Study guide

4.3 CCTV Inspection, Defect Identification & As-Built Verification

NZ PGDB Certifying Drainlayer Registration Examination Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Foul-Water Drainage System Design

1.1 Separated Drainage Systems & Cross-Connection Prevention 1.2 Drain Layout, Junctions, Bends & Sweep Connections 1.3 Gully Traps, Water Seals & Overflow Relief Gullies (ORG) 1.4 Boundary Connections, Inspection Shafts & Public Sewer Interface

2 Chapter 2: Drainage Ventilation & Commercial Waste Systems

2.1 Drainage Ventilation Systems, Relief Vents & Air Admittance Valves (AAVs) 2.2 Discharge Unit & Fixture Unit Sizing under G13/AS2 & AS/NZS 3500.2 2.3 Commercial Grease Interceptors & Oil/Grit Separators 2.4 Pumped Drainage Systems, Sumps & Rising Mains

3 Chapter 3: Stormwater Drainage & Surface Water Management

3.1 Stormwater Sizing & Flow Calculations to AS/NZS 3500.3 & E1/AS1 3.2 Stormwater Pits, Sumps, Silt Traps & Inlets 3.3 Soakage Systems, Retention & Detention Tanks 3.4 Overland Flow Paths & Secondary Flow Protection

4 Chapter 4: Drainage Testing & Quality Verification

4.1 Hydrostatic (Water) Testing Methods & Pressure Limits 4.2 Pneumatic (Air) Testing, Vacuum Testing & Leak Detection 4.3 CCTV Inspection, Defect Identification & As-Built Verification

5 Chapter 5: Trenching Safety & Confined Spaces

5.1 Excavation & Trenching Safety: Shoring, Battering & Benching 5.2 Confined Space Entry, Atmospheric Monitoring & Hazardous Gases 5.3 Underground Service Locating & Utility Strike Prevention 5.4 Site Health & Safety Management under the Health and Safety at Work Act 2015

6 Chapter 6: The Legislative & Regulatory Framework

6.1 Plumbers, Gasfitters, and Drainlayers Act 2006 & Board Functions 6.2 Licensing Classes, Registration Competencies & Annual Practising Licences 6.3 Disciplinary Regime, Offences, Complaints & Board Powers

7 Chapter 7: Certifying Drainlayer Authority & Site Supervision

7.1 Certifying Authority, Producer Statements & Records of Work 7.2 Supervision Principles: Direct vs General Supervision & Trainee Ratios 7.3 Professional Ethics, Continuing Professional Development (CPD) & Quality Assurance

8 Chapter 8: On-Site Wastewater System Design

8.1 AS/NZS 1547 Framework, Site Assessment & Soil Classification 8.2 Primary Treatment: Septic Tank Sizing, Baffles & Effluent Filters 8.3 Secondary Treatment: Aerated Wastewater Treatment Systems (AWTS) & Media Filters

9 Chapter 9: Land Application Systems & Environmental Protection

9.1 Land Application Systems: Absorption Trenches, Beds & Subsurface Drip Irrigation 9.2 Design Loading Rates (DLR), Reserve Areas & Hydraulic Sizing 9.3 Environmental Setbacks, Groundwater Protection & Resource Consents

10 Chapter 10: Pipe Materials, Jointing & Transitions

10.1 DWV Pipe Materials: uPVC, Vitrified Clay, PE & Concrete 10.2 Jointing Technologies: Solvent Cementing & Rubber Ring Joints 10.3 Dissimilar Material Adaptors, Flexible Couplings & Expansion Management

11 Chapter 11: Trench Bedding, Support & Backfill

11.1 Bedding Classes & Material Specifications under AS/NZS 3500.2 11.2 Cover Depths, Loading Conditions & Encasement Protection 11.3 Trench Backfill, Compaction Standards & Pipe Flotation Prevention

12 Chapter 12: Gradients, Invert Levels & Setting Out

12.1 Gradient Standards & Self-Cleansing Velocities under G13 & AS/NZS 3500.2 12.2 Fall, Grade & Run Calculations 12.3 Invert Level Calculations & Datum Relationships 12.4 Setting Out Methods: Laser Levels, Optical Instruments & Boning Rods

13 Chapter 13: Building Code Compliance & Service Separation

13.1 NZ Building Code Architecture: Clause G13, Clause E1 & Compliance Pathways 13.2 Service Separation: Clearances Between Foul Water, Stormwater & Other Utilities 13.3 Building Consent Authorities (BCAs), Code Compliance Certificates (CCC) & Council Inspections

14 Chapter 14: Examination Blueprint & Integrated Certifying Practice

14.1 Official Examination 9198 Blueprint, Logistics & Source Strategy 14.2 Plans, Specifications, Material Lists, Patterns, Tools & Equipment 14.3 Sustainability, Water Quality, Structural Integrity, Seismic & Geotechnical Resilience

4.3 CCTV Inspection, Defect Identification & As-Built Verification

Key Takeaways Explain This Topic AI

CCTV requirements and acceptance criteria come from the consent, network-owner specification, and inspection brief.

CCTV can identify visible defects and features but does not replace leakage testing, survey, or structural design verification.

Use the current inspection manual and authority coding requirements for public-asset or specified surveys.

Report observed evidence accurately and avoid applying an asset-owner threshold to unrelated private work.

Last updated: October 2026

CCTV inspection, defects, and as-built verification

CCTV is a useful inspection tool, but it is not universally mandatory for every private drain and it does not by itself prove Code compliance. The consent, network utility operator, asset-vesting specification, or project quality plan determines when a survey is required, which inspection manual applies, and what acceptance criteria are used.

Define the inspection brief

Before surveying, record the asset identifier, pipe material and nominal size, upstream and downstream limits, direction, purpose, cleaning requirements, coding manual and edition, authority specification, and deliverables. A private building drain, a public sewer proposed for vesting, and an existing condition survey may have different requirements.

Confirm that cleaning can be carried out without sending sediment, concrete slurry, or contaminated water to an unauthorised outfall. Manage confined-space, traffic, biological, jetting, and access hazards. Do not enter a chamber unless the work has been assessed and controlled under the applicable confined-space procedure.

What the camera can show

A correctly prepared survey can record cracks, breaks, roots, debris, infiltration, displaced joints, connections, surface damage, and visible ponding. A chainage counter and feature log allow observations to be located. Pan-and-tilt views can examine junctions and chambers. Laser profiling or other calibrated geometry tools may quantify deformation when the project specification requires them.

A standard camera image has limits. Water, steam, dirt, glare, lens distortion, speed, centralisation, and lighting affect interpretation. A camera’s inclinometer is not automatically a survey-grade invert profile. CCTV cannot see the bedding outside the pipe, prove leakage resistance, verify every material property, or establish a legal outfall.

Classification and acceptance

Use the current inspection manual named by the authority, together with that authority’s acceptance specification. Record the feature and severity code exactly as defined. Do not invent universal limits such as “all ponding over 10 mm fails” or “all flexible pipes over 5 percent deflection fail” without identifying the controlling asset standard and measurement method.

When a defect is suspected, distinguish observation from diagnosis. A joint appears displaced; poor bedding may be a cause, but excavation or other evidence may be needed. Report confidence, visibility limitations, and the extent of the feature.

Timing

A pre-cover camera run may confirm that the bore is clear before backfill. A post-construction run can reveal damage or deformation that occurred during compaction and traffic. The required timing comes from the project specification. Neither survey removes the need for the specified drainage leakage test, open-trench inspection, level survey, or commissioning.

As-built evidence

An as-built plan records the actual route, flow direction, pipe attributes, junctions, access, structures, outfall, and important levels or coordinates. CCTV can help locate features along a pipe, but chainage alone is not a geospatial coordinate. Tie the as-built to reliable site control and reconcile it with the approved design and variations.

A complete survey package commonly includes video files in the required format, a coded report, still images for significant features, asset and direction data, date, operator, equipment details, cleaning notes, visibility limitations, and recommendations. Preserve original files and issue corrected versions transparently.

Review scenario

A post-backfill survey shows standing water between chainages 12 m and 16 m. Do not automatically declare a fixed national “ponding failure.” Check the design grade, level survey, authority acceptance rule, camera orientation, pipe size, depth estimate, and whether water prevented a complete view. If the evidence shows a backfall outside the approved tolerance, specify a lawful repair and repeat the required verification. If the public-asset standard sets a deformation limit, use its measurement protocol rather than estimating from an uncalibrated image.

The certifier’s role is to combine sources: CCTV observations, installed levels, tests, construction records, design requirements, and authority criteria. No single record should be made to prove more than it actually demonstrates.

Independent source-check exercise

For 4.3 CCTV Inspection, Defect Identification & As-Built Verification , practise answering from evidence rather than recall. Write the controlling source, its edition or effective date, its scope, and the exact paragraph, table, figure, or manufacturer instruction that supports the decision. Then state the site inputs that can change the result. In this section those inputs include CCTV requirements and acceptance criteria come from the consent, network-owner specification, and inspection brief.; CCTV can identify visible defects and features but does not replace leakage testing, survey, or structural design verification.; Use the current inspection manual and authority coding requirements for public-asset or specified surveys..

Build a four-column check: proposed condition, source requirement, evidence observed, and action. Test the answer with one changed assumption. A different pipe size, discharge-unit load, ground condition, licence status, authority, compliance path, or consent condition may produce a different result. If it does, explain why; if it does not, show which requirement remains controlling.

Finish with a field-verification plan. Name what must be inspected before concealment, what instrument or record demonstrates it, who has authority to accept a change, and what appears on the as-built or completion file. This exercise turns an open-book fact into certifying-level judgement. It also exposes accidental mixing of standards: if the source for a dimension differs from the source for the test or approval, either return to one complete compliance path or document the proposal as an Alternative Solution. Do not promote an example value into a national rule.

Loading diagram... CCTV evidence limits