Study guide

4.2 Pneumatic (Air) Testing, Vacuum Testing & Leak Detection

NZ PGDB Certifying Drainlayer Registration Examination Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Foul-Water Drainage System Design

1.1 Separated Drainage Systems & Cross-Connection Prevention 1.2 Drain Layout, Junctions, Bends & Sweep Connections 1.3 Gully Traps, Water Seals & Overflow Relief Gullies (ORG) 1.4 Boundary Connections, Inspection Shafts & Public Sewer Interface

2 Chapter 2: Drainage Ventilation & Commercial Waste Systems

2.1 Drainage Ventilation Systems, Relief Vents & Air Admittance Valves (AAVs) 2.2 Discharge Unit & Fixture Unit Sizing under G13/AS2 & AS/NZS 3500.2 2.3 Commercial Grease Interceptors & Oil/Grit Separators 2.4 Pumped Drainage Systems, Sumps & Rising Mains

3 Chapter 3: Stormwater Drainage & Surface Water Management

3.1 Stormwater Sizing & Flow Calculations to AS/NZS 3500.3 & E1/AS1 3.2 Stormwater Pits, Sumps, Silt Traps & Inlets 3.3 Soakage Systems, Retention & Detention Tanks 3.4 Overland Flow Paths & Secondary Flow Protection

4 Chapter 4: Drainage Testing & Quality Verification

4.1 Hydrostatic (Water) Testing Methods & Pressure Limits 4.2 Pneumatic (Air) Testing, Vacuum Testing & Leak Detection 4.3 CCTV Inspection, Defect Identification & As-Built Verification

5 Chapter 5: Trenching Safety & Confined Spaces

5.1 Excavation & Trenching Safety: Shoring, Battering & Benching 5.2 Confined Space Entry, Atmospheric Monitoring & Hazardous Gases 5.3 Underground Service Locating & Utility Strike Prevention 5.4 Site Health & Safety Management under the Health and Safety at Work Act 2015

6 Chapter 6: The Legislative & Regulatory Framework

6.1 Plumbers, Gasfitters, and Drainlayers Act 2006 & Board Functions 6.2 Licensing Classes, Registration Competencies & Annual Practising Licences 6.3 Disciplinary Regime, Offences, Complaints & Board Powers

7 Chapter 7: Certifying Drainlayer Authority & Site Supervision

7.1 Certifying Authority, Producer Statements & Records of Work 7.2 Supervision Principles: Direct vs General Supervision & Trainee Ratios 7.3 Professional Ethics, Continuing Professional Development (CPD) & Quality Assurance

8 Chapter 8: On-Site Wastewater System Design

8.1 AS/NZS 1547 Framework, Site Assessment & Soil Classification 8.2 Primary Treatment: Septic Tank Sizing, Baffles & Effluent Filters 8.3 Secondary Treatment: Aerated Wastewater Treatment Systems (AWTS) & Media Filters

9 Chapter 9: Land Application Systems & Environmental Protection

9.1 Land Application Systems: Absorption Trenches, Beds & Subsurface Drip Irrigation 9.2 Design Loading Rates (DLR), Reserve Areas & Hydraulic Sizing 9.3 Environmental Setbacks, Groundwater Protection & Resource Consents

10 Chapter 10: Pipe Materials, Jointing & Transitions

10.1 DWV Pipe Materials: uPVC, Vitrified Clay, PE & Concrete 10.2 Jointing Technologies: Solvent Cementing & Rubber Ring Joints 10.3 Dissimilar Material Adaptors, Flexible Couplings & Expansion Management

11 Chapter 11: Trench Bedding, Support & Backfill

11.1 Bedding Classes & Material Specifications under AS/NZS 3500.2 11.2 Cover Depths, Loading Conditions & Encasement Protection 11.3 Trench Backfill, Compaction Standards & Pipe Flotation Prevention

12 Chapter 12: Gradients, Invert Levels & Setting Out

12.1 Gradient Standards & Self-Cleansing Velocities under G13 & AS/NZS 3500.2 12.2 Fall, Grade & Run Calculations 12.3 Invert Level Calculations & Datum Relationships 12.4 Setting Out Methods: Laser Levels, Optical Instruments & Boning Rods

13 Chapter 13: Building Code Compliance & Service Separation

13.1 NZ Building Code Architecture: Clause G13, Clause E1 & Compliance Pathways 13.2 Service Separation: Clearances Between Foul Water, Stormwater & Other Utilities 13.3 Building Consent Authorities (BCAs), Code Compliance Certificates (CCC) & Council Inspections

14 Chapter 14: Examination Blueprint & Integrated Certifying Practice

14.1 Official Examination 9198 Blueprint, Logistics & Source Strategy 14.2 Plans, Specifications, Material Lists, Patterns, Tools & Equipment 14.3 Sustainability, Water Quality, Structural Integrity, Seismic & Geotechnical Resilience

4.2 Pneumatic (Air) Testing, Vacuum Testing & Leak Detection

Key Takeaways Explain This Topic AI

The E1/VM1 low-pressure method charges to 300 mm water gauge, stabilises for five minutes, and permits no more than 50 mm drop.

The high-pressure method charges to 25 kPa, stabilises for at least two minutes, and times the decay from 17 kPa to 14 kPa.

Minimum high-pressure decay times are 3 minutes for 90–100 mm, 4 minutes for 150 mm, and 6 minutes for 225 mm pipe.

Compressed-air test plugs must be positively restrained and kept clear of people.

Last updated: October 2026

Pneumatic air testing

Air testing can be efficient, but compressed gas stores much more releasable energy than water. A detached plug or cap can become a projectile. Use air only where the compliance documents permit it, use rated equipment, positively restrain plugs, and keep everyone out of the line of fire.

E1/VM1 low-pressure method

For the low-pressure procedure, introduce air until the pressure is 300 mm water gauge. Allow the air temperature to become uniform, disconnect the air supply, and after five minutes measure the pressure. The drop must not exceed 50 mm water gauge. The numbers belong together; replacing 300 mm water gauge with 15 kPa would be a major error because 300 mm water gauge is about 2.9 kPa.

Use a suitable water manometer or calibrated gauge with adequate resolution. Check hoses and temporary fittings before blaming buried pipework. Temperature changes can change pressure even when no air escapes, which is why stabilization and disconnection are part of the sequence.

E1/VM1 high-pressure method

For the high-pressure procedure, raise pressure to 25 kPa and allow at least two minutes for stabilization. Disconnect the supply. Let pressure fall to 17 kPa, then measure the time to fall to 14 kPa. The minimum times are 3 minutes for 90 mm and 100 mm pipe, 4 minutes for 150 mm pipe, and 6 minutes for 225 mm pipe.

Do not invent a “zero pressure drop” criterion. The high-pressure method intentionally measures a controlled decay between two pressures. Do not continue adding air during the timed interval.

Safety controls

Identify plug diameter, rated pressure, restraint load, access, and escape path in the test plan. Restraint is structural; leaning a board against a plug or relying on an inflatable seal is not enough. Establish barriers and prohibit anyone from standing in front of a plug, cap, branch, or temporary connection. Fit pressure-limiting equipment suitable for the method and release pressure remotely where practical.

Inspect the system before charging. Unsupported fittings, solvent joints that have not achieved manufacturer cure time, and damaged inspection caps should not be exposed to pressure. Increase pressure gradually. Stop if the restraint moves, a fitting distorts, or an abnormal sound occurs.

Diagnosis and retest

A compatible leak-detection solution can identify exposed leakage, but clean and inspect the joint afterward. Sectional testing can narrow the search. Smoke may help trace an odour path or cross-connection, but it is a different diagnostic procedure and not automatically an acceptance test.

After a failure, fully depressurise, verify zero pressure, repair the defect, and repeat the complete specified sequence. Never loosen a plug that may still be loaded. Record test boundaries, method, pipe sizes, initial pressures, stabilization times, timed results, gauge identification, ambient conditions, repairs, and final acceptance.

Method-selection check

If the consent cites AS/NZS 3500.2 through G13/AS3, follow that edition’s procedure rather than substituting E1/VM1 values. If G13/AS2 expressly accepts an E1/VM1 air test, use the E1/VM1 sequence above. The reviewer should be able to trace every number in the test sheet to one named method. A safe test with a mismatched acceptance criterion is not a verified compliance result.

Independent source-check exercise

For 4.2 Pneumatic (Air) Testing, Vacuum Testing & Leak Detection , practise answering from evidence rather than recall. Write the controlling source, its edition or effective date, its scope, and the exact paragraph, table, figure, or manufacturer instruction that supports the decision. Then state the site inputs that can change the result. In this section those inputs include The E1/VM1 low-pressure method charges to 300 mm water gauge, stabilises for five minutes, and permits no more than 50 mm drop.; The high-pressure method charges to 25 kPa, stabilises for at least two minutes, and times the decay from 17 kPa to 14 kPa.; Minimum high-pressure decay times are 3 minutes for 90–100 mm, 4 minutes for 150 mm, and 6 minutes for 225 mm pipe..

Build a four-column check: proposed condition, source requirement, evidence observed, and action. Test the answer with one changed assumption. A different pipe size, discharge-unit load, ground condition, licence status, authority, compliance path, or consent condition may produce a different result. If it does, explain why; if it does not, show which requirement remains controlling.

Finish with a field-verification plan. Name what must be inspected before concealment, what instrument or record demonstrates it, who has authority to accept a change, and what appears on the as-built or completion file. This exercise turns an open-book fact into certifying-level judgement. It also exposes accidental mixing of standards: if the source for a dimension differs from the source for the test or approval, either return to one complete compliance path or document the proposal as an Alternative Solution. Do not promote an example value into a national rule.

Loading diagram... Air-test safety sequence