Study guide
12.3 Invert Level Calculations & Datum Relationships
NZ PGDB Certifying Drainlayer Registration Examination Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Foul-Water Drainage System Design
1.1 Separated Drainage Systems & Cross-Connection Prevention 1.2 Drain Layout, Junctions, Bends & Sweep Connections 1.3 Gully Traps, Water Seals & Overflow Relief Gullies (ORG) 1.4 Boundary Connections, Inspection Shafts & Public Sewer Interface
2 Chapter 2: Drainage Ventilation & Commercial Waste Systems
2.1 Drainage Ventilation Systems, Relief Vents & Air Admittance Valves (AAVs) 2.2 Discharge Unit & Fixture Unit Sizing under G13/AS2 & AS/NZS 3500.2 2.3 Commercial Grease Interceptors & Oil/Grit Separators 2.4 Pumped Drainage Systems, Sumps & Rising Mains
3 Chapter 3: Stormwater Drainage & Surface Water Management
3.1 Stormwater Sizing & Flow Calculations to AS/NZS 3500.3 & E1/AS1 3.2 Stormwater Pits, Sumps, Silt Traps & Inlets 3.3 Soakage Systems, Retention & Detention Tanks 3.4 Overland Flow Paths & Secondary Flow Protection
4 Chapter 4: Drainage Testing & Quality Verification
4.1 Hydrostatic (Water) Testing Methods & Pressure Limits 4.2 Pneumatic (Air) Testing, Vacuum Testing & Leak Detection 4.3 CCTV Inspection, Defect Identification & As-Built Verification
5 Chapter 5: Trenching Safety & Confined Spaces
5.1 Excavation & Trenching Safety: Shoring, Battering & Benching 5.2 Confined Space Entry, Atmospheric Monitoring & Hazardous Gases 5.3 Underground Service Locating & Utility Strike Prevention 5.4 Site Health & Safety Management under the Health and Safety at Work Act 2015
6 Chapter 6: The Legislative & Regulatory Framework
6.1 Plumbers, Gasfitters, and Drainlayers Act 2006 & Board Functions 6.2 Licensing Classes, Registration Competencies & Annual Practising Licences 6.3 Disciplinary Regime, Offences, Complaints & Board Powers
7 Chapter 7: Certifying Drainlayer Authority & Site Supervision
7.1 Certifying Authority, Producer Statements & Records of Work 7.2 Supervision Principles: Direct vs General Supervision & Trainee Ratios 7.3 Professional Ethics, Continuing Professional Development (CPD) & Quality Assurance
8 Chapter 8: On-Site Wastewater System Design
8.1 AS/NZS 1547 Framework, Site Assessment & Soil Classification 8.2 Primary Treatment: Septic Tank Sizing, Baffles & Effluent Filters 8.3 Secondary Treatment: Aerated Wastewater Treatment Systems (AWTS) & Media Filters
9 Chapter 9: Land Application Systems & Environmental Protection
9.1 Land Application Systems: Absorption Trenches, Beds & Subsurface Drip Irrigation 9.2 Design Loading Rates (DLR), Reserve Areas & Hydraulic Sizing 9.3 Environmental Setbacks, Groundwater Protection & Resource Consents
10 Chapter 10: Pipe Materials, Jointing & Transitions
10.1 DWV Pipe Materials: uPVC, Vitrified Clay, PE & Concrete 10.2 Jointing Technologies: Solvent Cementing & Rubber Ring Joints 10.3 Dissimilar Material Adaptors, Flexible Couplings & Expansion Management
11 Chapter 11: Trench Bedding, Support & Backfill
11.1 Bedding Classes & Material Specifications under AS/NZS 3500.2 11.2 Cover Depths, Loading Conditions & Encasement Protection 11.3 Trench Backfill, Compaction Standards & Pipe Flotation Prevention
12 Chapter 12: Gradients, Invert Levels & Setting Out
12.1 Gradient Standards & Self-Cleansing Velocities under G13 & AS/NZS 3500.2 12.2 Fall, Grade & Run Calculations 12.3 Invert Level Calculations & Datum Relationships 12.4 Setting Out Methods: Laser Levels, Optical Instruments & Boning Rods
13 Chapter 13: Building Code Compliance & Service Separation
13.1 NZ Building Code Architecture: Clause G13, Clause E1 & Compliance Pathways 13.2 Service Separation: Clearances Between Foul Water, Stormwater & Other Utilities 13.3 Building Consent Authorities (BCAs), Code Compliance Certificates (CCC) & Council Inspections
14 Chapter 14: Examination Blueprint & Integrated Certifying Practice
14.1 Official Examination 9198 Blueprint, Logistics & Source Strategy 14.2 Plans, Specifications, Material Lists, Patterns, Tools & Equipment 14.3 Sustainability, Water Quality, Structural Integrity, Seismic & Geotechnical Resilience
12.3 Invert Level Calculations & Datum Relationships
Key Takeaways Explain This Topic AI
Invert Level (IL) is the elevation of the internal bottom flow-line of a pipe; Crown Level (CL) is the external top of the barrel; Soffit Level is the internal top of the barrel.
Downstream Invert Level equals Upstream Invert Level minus Fall, whereas Upstream Invert Level equals Downstream Invert Level plus Fall.
New Zealand drainage engineering references the New Zealand Vertical Datum 2016 (NZVD2016); drainlayers must identify legacy local datum offsets (e.g. Auckland 1946, Lyttelton 1937) to prevent fatal connection errors.
Trench excavation depth (dig level) must account for pipe outside diameter, wall thickness, and granular bedding thickness (typically 75 mm to 100 mm under AS/NZS 3500.2).
The certifying drainlayer has a mandatory duty to physically pot-hole and verify the council connection lateral invert before trenching private drains.
Last updated: October 2026
Invert Level Calculations & Datum Relationships
In drainage engineering, vertical elevation is everything. Unlike surface building works where dimensions are taken from floor finishes or framing plates, underground pipe networks are referenced to precise geodetic datums. The certifying drainlayer must be able to calculate, verify, and cross-reference levels across plans, site benchmarks, and trench excavations with millimetre accuracy.
A single error in understanding the distinction between an Invert Level , a Crown Level , and a Bedding Dig Level can result in a pipeline colliding with municipal services, failing to achieve gravity fall to the council main, or being buried with insufficient cover depth under NZBC Clause G13/AS2 and AS/NZS 3500.2:2021. Furthermore, New Zealand's transition from historical local vertical datums to the modern New Zealand Vertical Datum 2016 (NZVD2016) introduces regional datum offset traps that certifying drainlayers must navigate on every civil infrastructure connection.
1. Definitive Terminology of Pipeline Levels
To eliminate site confusion, professional drainlayers and civil engineers utilize standardized vertical reference definitions: +-------------------------------------------------------------+
- | PIPELINE CROSS-SECTION GEOMETRY |
- | |
- | Finished Ground Level (GL) / Cover Level |
- | ==================================================== |
- | | |
- | | Cover Depth (GL - CL) |
- | v |
- | +-----------------------+ <--- Crown Level (CL) [Ext Top] |
- | | Pipe Wall Thickness | |
- | | +-------------------+ | <--- Soffit / Obvert [Int Top] |
- | | | | | |
- | | | Pipe Bore (ID) | | |
- | | | | | |
- | | +-------------------+ | <--- Invert Level (IL) [Int Btm]|
- | +-----------------------+ <--- Pipe Underside [Ext Btm] |
- | | Granular Bedding (75) | |
- | ========================= <--- Bottom-of-Trench Dig Level |
- | Undisturbed Trench Bed |
- +-------------------------------------------------------------+
Invert Level (IL): The elevation of the lowest point on the internal bottom surface of the pipe barrel. This is the hydraulic flow-line where wastewater travels and is the primary elevation quoted on all drainage plans.
Soffit Level (Obvert): The elevation of the highest point on the internal top surface of the pipe bore: Soffit Level = Invert Level + Internal Diameter (ID) \text{Soffit Level} = \text{Invert Level} + \text{Internal Diameter (ID)} Soffit Level = Invert Level + Internal Diameter (ID) When pipes of different diameters connect in an inspection chamber or junction (e.g. DN 100 connecting to DN 150), they must be aligned soffit-to-soffit (top-inside to top-inside). Aligning them invert-to-invert creates an abrupt step at the crown that traps sewer gases, while aligning centre-to-centre creates a backwater lip.
Crown Level (CL): The elevation of the highest point on the external top surface of the pipe barrel: Crown Level = Invert Level + Internal Diameter + ( 2 × Pipe Wall Thickness ) = Invert Level + Outside Diameter (OD) \text{Crown Level} = \text{Invert Level} + \text{Internal Diameter} + (2 \times \text{Pipe Wall Thickness}) = \text{Invert Level} + \text{Outside Diameter (OD)} Crown Level = Invert Level + Internal Diameter + ( 2 × Pipe Wall Thickness ) = Invert Level + Outside Diameter (OD)
Ground Level (GL) / Cover Level / Surface Level (SL): The finished surface elevation directly above the pipeline centerline (e.g. top of lawn, asphalt, or concrete driveway).
Cover Depth: The vertical depth of backfill material between the ground surface and the external top of the pipe: Cover Depth = Ground Level − Crown Level \text{Cover Depth} = \text{Ground Level} - \text{Crown Level} Cover Depth = Ground Level − Crown Level
Bottom-of-Trench Dig Level (Excavation RL): The elevation to which the excavator bucket must cut the native ground before placing the granular bedding material: Dig Level = Invert Level − Pipe Wall Thickness − Bedding Thickness \text{Dig Level} = \text{Invert Level} - \text{Pipe Wall Thickness} - \text{Bedding Thickness} Dig Level = Invert Level − Pipe Wall Thickness − Bedding Thickness
2. Tracing Invert Levels Along Gravity Pipelines
When navigating a drainage line across a property, calculating inverts proceeds sequentially from station to station:
Progressive Calculation Formulas
Moving Downstream (In Direction of Flow): As the pipe falls toward the outfall, elevation decreases: IL downstream = IL upstream − Fall \text{IL}_{\text{downstream}} = \text{IL}_{\text{upstream}} - \text{Fall} IL downstream = IL upstream − Fall
Moving Upstream (Against Flow): When calculating back from a fixed council connection point up toward the house: IL upstream = IL downstream + Fall \text{IL}_{\text{upstream}} = \text{IL}_{\text{downstream}} + \text{Fall} IL upstream = IL downstream + Fall
Passing Through a Manhole with an Invert Step: IL manhole outlet = IL manhole inlet − Step Drop \text{IL}_{\text{manhole outlet}} = \text{IL}_{\text{manhole inlet}} - \text{Step Drop} IL manhole outlet = IL manhole inlet − Step Drop
3. Geodetic Datums & Elevation Reference Systems in New Zealand
All official survey elevations in New Zealand are expressed as Reduced Levels (RL) relative to an established vertical datum plane.
New Zealand Vertical Datum 2016 (NZVD2016)
Prior to modern satellite geodesy, New Zealand utilized more than a dozen separate local vertical datums, each established in the mid-20th century based on local tide gauge observations of Mean Sea Level (MSL). In 2016, Land Information New Zealand (LINZ) formally introduced NZVD2016 as the official national vertical datum. NZVD2016 is defined by a gravimetric geoid model (NZGeoid2016) that provides a consistent, mathematically continuous vertical reference across the entire nation.
The Local Datum Conversion Trap
While all modern council GIS databases and LINZ survey plans utilize NZVD2016, older territorial authority drainage records (as-builts from the 1960s to 2010s) frequently reference historical local vertical datums. The vertical offset between a local datum and NZVD2016 is substantial and varies geographically:
Region / Local Authority Historical Local Datum Offset to NZVD2016 (Add offset to convert Local to NZVD2016) Trade Impact if Datum Ignored
Auckland Council Auckland 1946 + 0.34 m +0.34\text{ m} + 0.34 m ( + 340 mm +340\text{ mm} + 340 mm ) Sewer appears 340 mm deeper or higher than reality.
Tauranga / Bay of Plenty Moturiki 1953 + 0.24 m +0.24\text{ m} + 0.24 m ( + 240 mm +240\text{ mm} + 240 mm ) Severe risk of trenching below connection stub.
Wellington City Wellington 1953 + 0.44 m +0.44\text{ m} + 0.44 m ( + 440 mm +440\text{ mm} + 440 mm ) Drain misaligned with public sewer main.
Christchurch City Lyttelton 1937 + 0.47 m +0.47\text{ m} + 0.47 m ( + 470 mm +470\text{ mm} + 470 mm ) Fall calculation completely invalidated.
Dunedin City Dunedin 1958 + 0.38 m +0.38\text{ m} + 0.38 m ( + 380 mm +380\text{ mm} + 380 mm ) Connection point cannot receive gravity flow.
Critical Exam Rule: Never transfer an elevation from a council GIS drawing to a physical drainage trench without verifying whether the drawing references NZVD2016 or a Local Vertical Datum . A 400 mm 400\text{ mm} 400 mm datum error completely destroys the gradient on a 1 : 60 1:60 1 : 60 pipeline!
Benchmarks (BM) and Temporary Benchmarks (TBM)
Benchmark (BM): A permanent, officially surveyed marker (brass plaque, stainless steel pin, or survey pillar) with an accurately published RL.
Temporary Benchmark (TBM): A stable site reference point established by the surveyor or certifying drainlayer (e.g. top of a boundary survey peg, marked kerb corner, or concrete foundation plinth). All site optical and laser levels are calibrated against the TBM.
4. The Council Connection Audit: Verifying Available Fall
Under New Zealand regional bylaws and the Plumbers, Gasfitters, and Drainlayers Act 2006, a Certifying Drainlayer has a statutory duty of care to verify that gravity discharge is achievable before commencing installation.
The "Hanging a Drain" Disaster
A catastrophic trade failure occurs when a drainlayer lays pipework from a new house out toward the boundary, only to discover that the council sewer connection stub is 200 mm 200\text{ mm} 200 mm higher than anticipated. The drain is now "hung": it cannot connect by gravity, the trench must be re-excavated, or the client must fund an unconsented NZ$15,000 pump station.
The Mandatory Verification Procedure
Locate Council As-Built Drawing: Review the council public drainage record for the lateral connection stub (diameter, material, and surveyed Invert Level).
Physical Pot-Holing (Vacuum or Hand Excavation): Before excavating the building platform or laying a single pipe, physically uncover the council connection stub at the property boundary.
Direct Instrument Measurement: Take an optical level backsight onto the verified site TBM and take an inverted or direct foresight reading on the actual physical pipe invert of the council connection.
Compare Survey RL to Design RL: Calculate available fall using the true physical level. If there is a discrepancy exceeding 20 mm 20\text{ mm} 20 mm , redesign gradients immediately.
5. Excavation Depth & Bedding Allowance Calculations
When excavating trenches, machine operators cut to the bottom of the trench, not the pipe invert. The certifying drainlayer must provide the machine operator with the Trench Dig Level (Excavation RL) .
Pipe Specifications (AS/NZS 1260 uPVC SN4 / SN8)
DN 100 uPVC DWV: Outside Diameter (OD) = 110.2 mm 110.2\text{ mm} 110.2 mm , Wall Thickness = 3.2 mm 3.2\text{ mm} 3.2 mm , Internal Diameter (ID) = 103.8 mm 103.8\text{ mm} 103.8 mm .
DN 150 uPVC DWV: Outside Diameter (OD) = 160.3 mm 160.3\text{ mm} 160.3 mm , Wall Thickness = 4.7 mm 4.7\text{ mm} 4.7 mm , Internal Diameter (ID) = 150.9 mm 150.9\text{ mm} 150.9 mm .
Bedding Classes under AS/NZS 3500.2 Clause 3.7 & NZBC G13/AS2
Class B Bedding (Standard Trade Bedding): Minimum 75 mm 75\text{ mm} 75 mm of compacted granular bedding material (crushed stone chips 7 7 7 to 10 mm 10\text{ mm} 10 mm or coarse sand) placed beneath the underside of the pipe barrel in stable soil.
Rock Excavation: Where the trench base is cut into solid rock, shale, or hard unyielding ground, the bedding thickness must be increased to a minimum of 100 mm 100\text{ mm} 100 mm to prevent point-loading stones from puncturing the pipe wall.
Calculating Dig Level (Excavation Floor RL) Trench Bottom RL = Design Invert Level − Pipe Wall Thickness − Bedding Thickness \text{Trench Bottom RL} = \text{Design Invert Level} - \text{Pipe Wall Thickness} - \text{Bedding Thickness} Trench Bottom RL = Design Invert Level − Pipe Wall Thickness − Bedding Thickness
For a DN 100 pipe with an Invert Level of RL 34.500 m \text{RL } 34.500\text{ m} RL 34.500 m on standard 75 mm 75\text{ mm} 75 mm Class B bedding in soil: Trench Bottom RL = 34.500 − 0.0032 − 0.075 = RL 34.422 m \text{Trench Bottom RL} = 34.500 - 0.0032 - 0.075 = \text{RL } 34.422\text{ m} Trench Bottom RL = 34.500 − 0.0032 − 0.075 = RL 34.422 m Excavation Depth from Surface (GL 35.200 m) = 35.200 − 34.422 = 0.778 m = 778 mm \text{Excavation Depth from Surface (GL 35.200 m)} = 35.200 - 34.422 = 0.778\text{ m} = 778\text{ mm} Excavation Depth from Surface (GL 35.200 m) = 35.200 − 34.422 = 0.778 m = 778 mm
6. Worked Comprehensive Chainage and Invert Schedule
To demonstrate an exam-level setting-out problem, consider a proposed 48-metre DN 100 private foul drain serving a new residential dwelling, discharging into a council boundary lateral.
Site Survey & Engineering Data
Boundary Connection Stub (Chainage 0.00 m 0.00\text{ m} 0.00 m ): Surveyed Invert Level = RL 12.350 m \text{RL } 12.350\text{ m} RL 12.350 m . Ground Level = RL 13.250 m \text{RL } 13.250\text{ m} RL 13.250 m .
Inspection Chamber (Chainage 20.00 m 20.00\text{ m} 20.00 m ): Change of direction; requires a 30 mm 30\text{ mm} 30 mm ( 0.030 m 0.030\text{ m} 0.030 m ) invert drop across the benching.
Dwelling Gully Trap (Chainage 48.00 m 48.00\text{ m} 48.00 m ): Ground Level = RL 14.100 m \text{RL } 14.100\text{ m} RL 14.100 m .
Pipe Sizing & Gradient: Entire line is DN 100 uPVC (OD = 110.2 mm 110.2\text{ mm} 110.2 mm , wall = 3.2 mm 3.2\text{ mm} 3.2 mm ). Designed at minimum compliant grade of 1 : 60 1:60 1 : 60 ( 1.67 % 1.67\% 1.67% or 16.7 mm/m 16.7\text{ mm/m} 16.7 mm/m ).
Bedding: 75 mm 75\text{ mm} 75 mm Class B bedding throughout.
Step 1: Calculate Pipeline Inverts from Outfall Upstream
Boundary Stub (Chainage 0.00 m 0.00\text{ m} 0.00 m ): IL 0.0 = RL 12.350 m \text{IL}_{0.0} = \text{RL } 12.350\text{ m} IL 0.0 = RL 12.350 m
Inspection Chamber Outlet (Chainage 20.00 m 20.00\text{ m} 20.00 m ): Fall 0 to 20 = 20.00 m 60 = 0.333 m \text{Fall}_{0\text{ to }20} = \frac{20.00\text{ m}}{60} = 0.333\text{ m} Fall 0 to 20 = 60 20.00 m = 0.333 m IL Chamber Outlet = 12.350 + 0.333 = RL 12.683 m \text{IL}_{\text{Chamber Outlet}} = 12.350 + 0.333 = \text{RL } 12.683\text{ m} IL Chamber Outlet = 12.350 + 0.333 = RL 12.683 m
Inspection Chamber Inlet (Chainage 20.00 m 20.00\text{ m} 20.00 m ): Add the 30 mm 30\text{ mm} 30 mm chamber step drop: IL Chamber Inlet = 12.683 + 0.030 = RL 12.713 m \text{IL}_{\text{Chamber Inlet}} = 12.683 + 0.030 = \text{RL } 12.713\text{ m} IL Chamber Inlet = 12.683 + 0.030 = RL 12.713 m
Gully Trap Connection (Chainage 48.00 m 48.00\text{ m} 48.00 m ): Run from Chamber to Gully = 48.00 − 20.00 = 28.00 m 48.00 - 20.00 = 28.00\text{ m} 48.00 − 20.00 = 28.00 m . Fall 20 to 48 = 28.00 m 60 = 0.467 m \text{Fall}_{20\text{ to }48} = \frac{28.00\text{ m}}{60} = 0.467\text{ m} Fall 20 to 48 = 60 28.00 m = 0.467 m IL 48.0 = 12.713 + 0.467 = RL 13.180 m \text{IL}_{48.0} = 12.713 + 0.467 = \text{RL } 13.180\text{ m} IL 48.0 = 12.713 + 0.467 = RL 13.180 m
Step 2: Tabulated Setting-Out Schedule
Chainage (m) Station Description Ground Level (GL) Invert Level (IL) Crown Level (CL) Dig Level RL (IL - 78mm) Excavation Depth (mm) Cover Depth (mm) Compliance Check (Min Cover 500mm under unpaved ground)
0.00 m Boundary Stub RL 13.250 m RL 12.350 m RL 12.460 m RL 12.272 m 978 mm 790 mm Compliant ( 790 > 500 mm 790 > 500\text{ mm} 790 > 500 mm )
12.00 m Intermediate Station RL 13.500 m RL 12.550 m RL 12.660 m RL 12.472 m 1028 mm 840 mm Compliant ( 840 > 500 mm 840 > 500\text{ mm} 840 > 500 mm )
20.00 m (Out) Chamber Outlet RL 13.680 m RL 12.683 m RL 12.793 m RL 12.605 m 1075 mm 887 mm Compliant ( 887 > 500 mm 887 > 500\text{ mm} 887 > 500 mm )
20.00 m (In) Chamber Inlet RL 13.680 m RL 12.713 m RL 12.823 m RL 12.635 m 1045 mm 857 mm Compliant ( 857 > 500 mm 857 > 500\text{ mm} 857 > 500 mm )
36.00 m Intermediate Station RL 13.920 m RL 12.980 m RL 13.090 m RL 12.902 m 1018 mm 830 mm Compliant ( 830 > 500 mm 830 > 500\text{ mm} 830 > 500 mm )
48.00 m Gully Trap Riser RL 14.100 m RL 13.180 m RL 13.290 m RL 13.102 m 998 mm 810 mm Compliant ( 810 > 500 mm 810 > 500\text{ mm} 810 > 500 mm )
7. Trade Traps in Invert Level Management +-------------------------------------------------------------------------+
- | DRAINLAYER TRADE TRAPS |
- | |
- | [!] THE 'TRENCH FLOOR IS THE INVERT' TRAP |
- | Forgetting the 75 mm bedding and 3 mm wall thickness when measuring |
- | trench depth with a boning rod. The finished pipe ends up 78 mm too |
- | high, losing all fall or emerging above ground. |
- | |
- | [!] THE INVERT-TO-INVERT EXPANSION BLUNDER |
- | Connecting a DN 100 pipe invert-to-invert with a DN 150 pipe at an |
- | inspection chamber. The soffit step restricts air movement, while |
- | expanding wastewater creates a hydraulic jump and solids dam. |
- | |
- | [!] THE GIS DATUM BLINDSPOT |
- | Assuming an older council as-built RL is on NZVD2016. In Auckland, an |
- | uncorrected 1946 datum offset introduces a 340 mm vertical error that |
- | destroys the entire gravity drainage design. |
- +-------------------------------------------------------------------------+