Study guide
7.2 Springs, Struts, Arms, Air Suspension & Ride Height
NZTA Warrant of Fitness WoF
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Inspector Administration, Legal Rules & Certification Workflow
1.1 Becoming a WoF Inspector: Appointment, Assessment & Professional Duties 1.2 WoF Validity, Reference Dates & Label Control 1.3 Inspection Records, Rechecks, Complaints & Quality Management
2 Chapter 2: Vehicle Identification, Body Exterior & Structural Corrosion
2.1 VIN, Chassis Number & Vehicle-Record Identification 2.2 External Projections, Vehicle Dimensions & Mudguards 2.3 Structure, Frontal-Impact Systems & Corrosion Decisions
3 Chapter 3: Glazing, Vision, Mirrors & Vehicle Access
3.1 Windscreen, Critical Vision Area & Damage Limits 3.2 Safety Glazing, VLT, Overlays & Driver Vision 3.3 Visors, Wipers, Washers, Mirrors & Door Retention
4 Chapter 4: Lighting, Signalling & Electrical Safety
4.1 Headlamps, Fog Lamps, Cornering Lamps & DRLs 4.2 Direction Indicators, Position Lamps, Side Markers & End-Outline Lamps 4.3 Stop Lamps, High-Mounted Stop Lamps, Plate Lamps, Reflectors & Reversing Lamps
5 Chapter 5: Tyres, Wheels & Running Gear
5.1 Tyre Tread, Damage, Winter Tyres & TPMS 5.2 Tyre Size, Carcass, Load/Speed Categories & Modifications 5.3 Wheels, Fasteners, Hubs & Axles
6 Chapter 6: Braking Systems & Performance Testing
6.1 Service & Parking Brake Performance 6.2 Brake Pedal, Hydraulics, Friction Components & Parking Mechanism 6.3 ABS, ESC, Brake Warnings & Brake Modifications
7 Chapter 7: Steering & Suspension Systems
7.1 Steering Wheel, Column, Linkages, Rack & Power Assistance 7.2 Springs, Struts, Arms, Air Suspension & Ride Height 7.3 Dampers, Ball Joints, Bushes, Sway Bars & Suspension Operation
8 Chapter 8: Interior Safety, Seatbelts & Occupant Protection
8.1 Seats, Anchorages, Head Restraints & Interior Impact 8.2 Seatbelts, Retractors, Buckles, Pretensioners & Anchorages 8.3 Frontal Airbags, Speedometer & Audible Warning Device
9 Chapter 9: Exhaust, Fuel Systems, Alternative Fuels & LVV Modifications
9.1 Exhaust System, Noise Evidence & Visible Emissions 9.2 Engine/Driveline, Liquid Fuel & LPG/CNG Systems 9.3 EV/Hybrid Safety, Towbars & Modification Certification
7.2 Springs, Struts, Arms, Air Suspension & Ride Height
Key Takeaways Explain This Topic AI
Suspension components fail for insecurity, damage, excessive wear/play, binding, or excessive damping-fluid/air leakage as specified.
Replacement springs must remain captive in unmodified OE seats through full travel and must not be cut, heated, or made height-adjustable unless OE.
The uncertified replacement-spring route requires at least 40 mm rebound wheel travel and 100 mm ground clearance under the specified conditions.
Strut or spring spacers always require certification; leaf-spring blocks have a specific conditional allowance including a 50 mm maximum.
An air bellows with protruding or worn cords is rejected, and certified ride height must match the value recorded on the LVV plate.
Last updated: October 2026
Separate condition from modification
Inspect the suspension as fitted, then decide whether any change is excluded from LVV certification. A vehicle can fail for condition even when its modification is certified, and can fail for missing certification even when components look new.
Springs, arms, struts, and air systems
Page 9-1 covers shock absorbers, springs, upper and lower arms, sway bars, air suspension, and kingpins. Reject components or mountings that are insecure, cracked, fractured, deformed, excessively worn, seized, or have play beyond manufacturer specifications. Check spring seats, locating features, U-bolts, control-arm pivots, strut towers, and subframe points.
A spring must remain correctly located through suspension travel. Reject a cut or heated spring, a spring not self-retaining in its seat, or makeshift wire ties/straps used to keep it captive. Check leaf springs for fracture, displacement, insecure clamps, worn eyes/bushes, and axle attachment problems.
For air suspension, inspect bellows at normal ride height and pressure. Obvious external damage with protruding or worn cords is a reason for rejection. Apply the excessive air-leakage and operation rules; do not fail harmless moulding seams as cracks without evidence.
Uncertified replacement-spring route
The modification table can exclude direct replacement springs and shock absorbers from LVV certification only when every condition is met. Important conditions include:
- unmodified OE spring seats and mountings;
- springs self-retaining at full extension without non-standard retainers;
- no heating, cutting, or non-OE height adjustment;
- adequate suspension travel and clearance;
- more than 40 mm rebound (droop) wheel travel ; and
at least 100 mm ground clearance , unladen and without the driver, below the vehicle structure or steering, braking, or suspension components, subject to the VIRM note.
This is not a general statement that “up to 50 mm lowering never needs certification.” The table’s conditions, geometry, travel, and component type all matter.
Strut or spring spacers always require certification. Leaf-spring blocks can be excluded only under their detailed conditions, including no other raising method and blocks no more than 50 mm high. OE torsion-bar or OE adjustable-air-suspension adjustments have their own route.
Certified ride height
Where suspension is LVV-certified, measure from the wheel centre to the underside of the wheel arch with the vehicle unladen as directed. Reject when the current ride height differs from the value listed on the LVV plate. Also confirm the plate covers the components actually fitted.
Inspection sequence
Observe stance and compare side-to-side height.
Inspect springs, seats, arms, struts, bars, kingpins, bellows, and mountings.
Safely load/unload joints using the proper jacking points and method.
Check travel, bump-stop clearance, tyre/body clearance, and ground clearance.
Identify spacers, adjustable seats, blocks, air conversions, or changed mounts.
Apply every condition in the modification-table exclusion.
Compare certified ride height and hardware to the LVV record.
Scenario
A car has non-adjustable lowering springs that remain captive and clears the ground by 105 mm, but rebound travel measures 30 mm. It does not meet the full uncertified exclusion, because the table requires more than 40 mm rebound; ground clearance alone is not enough.
Caution
Never certify a modification from one attractive number. Every condition in the table is cumulative.
Modification-table discipline
Measure rebound as the difference between the tyre-to-arch reference with the vehicle resting and at full rebound, following the note; record the points so the result can be repeated. Ground clearance is checked in the specified unladen state and excludes only items the note excludes. An exhaust or cosmetic part may have a different rule than structure, steering, brakes or suspension, so quote the actual low point.
Inspect bump stops and spring aids. A high-density bump stop is not intended to carry the vehicle continuously; a compliant spring aid can engage under loading as described in the note. Cut stops, coil bind, tyre contact, and insufficient travel can fail even when static ride height matches a plate. Adjustable spring seats are not made acceptable by locking them at factory height.
Condition still controls after certification
An LVV plate confirms an approved configuration at certification; it does not excuse later wear, loose adjusters, leaking dampers, cracked arms, tyre contact or corrosion. Compare identifiers and listed height/components, then perform the full in-service inspection. If hardware differs from the certified description, treat it as an uncovered modification. If hardware matches but is worn or damaged, fail under the ordinary condition reason rather than calling the plate invalid.