Study guide

4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10)

Oklahoma Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety

1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection

2 Chapter 2: General Electrical Theory & Calculations

2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments

3 Chapter 3: General Installation Requirements (NEC Article 110)

3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable

4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)

4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)

5 Chapter 5: Services & Service Equipment (NEC Article 230)

5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)

6 Chapter 6: Electrical Load Calculations (NEC Article 220)

6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)

7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)

7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)

8 Chapter 8: Grounding and Bonding (NEC Article 250)

8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)

9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)

9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)

10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems

10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)

11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)

11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)

12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)

12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)

13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)

13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)

14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems

14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)

4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10)

Key Takeaways Explain This Topic AI

Branch circuits are classified by the maximum permitted rating or setting of their overcurrent protective device (15A, 20A, 30A, 40A, and 50A per NEC 210.3); multi-outlet branch circuits are restricted strictly to these standard ratings.

Under NEC 210.23, cord-and-plug loads not fastened in place must not exceed 80% of branch circuit rating (12A for 15A circuit, 16A for 20A circuit), while fastened-in-place utilization equipment cannot exceed 50% when lighting or portable loads are also supplied.

Multiwire branch circuits (NEC 210.4) require simultaneous disconnect of all ungrounded conductors, originating from different phases to prevent neutral overload, conductor grouping in panels (210.4(D)), and neutral pigtailing (300.13(B)).

Continuous loads (operating 3 hours or more) require branch circuit conductors and overcurrent protective devices to be sized at not less than 125% of the continuous load plus 100% of the non-continuous load (NEC 210.19(A)(1) and 210.20(A)).

Conductor identification rules under NEC 210.5 and 200.6 mandate continuous white or gray for grounded conductors, green/bare for equipment grounding, and documented phase identification posted at panelboards where multiple voltage systems are present.

Last updated: August 2026

Branch Circuit Ratings, Multiwire Branch Circuits & Identification (NEC 210.3–210.10)

Branch circuits represent the final link in the electrical distribution system, extending from the last overcurrent protective device (fuse or circuit breaker) to the utilization equipment and receptacle outlets. Because branch circuits directly interface with appliances, lighting, and building occupants, the National Electrical Code (NEC) enforces rigorous rules governing their sizing, loading, multiwire configurations, and conductor identification. On the Oklahoma Journeyman Electrician examination, mastering NEC Article 210 is foundational for both calculation problems and code compliance questions.

1. Branch Circuit Ratings & Standard Classifications (NEC 210.3)

Branch circuits are rated according to the maximum permitted ampere rating or setting of their overcurrent protective device (OCPD). NEC 210.3 establishes that branch circuits recognized by Article 210 shall be rated as follows:

Standard Multi-Outlet Branch Circuit Ratings: 15, 20, 30, 40, and 50 Amperes .

Individual Branch Circuits: Circuits supplying a single piece of utilization equipment (e.g., a 60A industrial welder or a 100A commercial chiller) may have any ampere rating and are not restricted to the standard multi-outlet ratings.

Conductor Sizing Coordination: Conductor ampacity must never be lower than the branch circuit rating. For instance, if a 20A circuit breaker protects a circuit, the conductors must have an allowable ampacity of at least 20A (typically #12 AWG copper under NEC Table 310.16 and 240.4(D)). +-----------------------------------------------------------------------------+

  • | STANDARD BRANCH CIRCUIT SUMMARY (NEC 210.3) |
  • | |
  • | CIRCUIT RATING MIN CONDUCTOR (Cu) OCPD RATING COMMON APPLICATIONS |
  • | ----------------------------------------------------------------------- |
  • | 15 Amperes #14 AWG 15 Amperes General Lighting |
  • | 20 Amperes #12 AWG 20 Amperes SABC, Bathrooms |
  • | 30 Amperes #10 AWG 30 Amperes Dryers, Water Heater |
  • | 40 Amperes #8 AWG 40 Amperes Cooktops, Commercial |
  • | 50 Amperes #6 AWG 50 Amperes Ranges, EV Chargers |
  • +-----------------------------------------------------------------------------+
  • 2. Permissible Loads & Load Limits (NEC 210.23)

In no case shall the total continuous and non-continuous load exceed the rating of the branch circuit. When multiple outlets are served by a single branch circuit, NEC 210.23 imposes strict percentage limits based on equipment fastening and mobility:

15-Ampere and 20-Ampere Branch Circuits (NEC 210.23(A))

Cord-and-Plug-Connected Equipment NOT Fastened in Place (210.23(A)(1)):

The rating of any single portable cord-and-plug appliance shall not exceed 80% of the branch circuit ampere rating.

On a 15A circuit: Maximum portable load = 15 A × 0.80 = 12.0 Amperes 15\text{ A} \times 0.80 = \mathbf{12.0\text{ Amperes}} 15 A × 0.80 = 12.0 Amperes (1,440 VA at 120V).

On a 20A circuit: Maximum portable load = 20 A × 0.80 = 16.0 Amperes 20\text{ A} \times 0.80 = \mathbf{16.0\text{ Amperes}} 20 A × 0.80 = 16.0 Amperes (1,920 VA at 120V).

Utilization Equipment Fastened in Place (210.23(A)(2)):

Where a circuit supplies lighting units, cord-and-plug equipment not fastened in place, OR both, any fastened-in-place appliance (such as a garbage disposal, dishwasher, or attic exhaust fan) shall not exceed 50% of the branch circuit rating.

On a 15A circuit: Maximum fastened-in-place load = 15 A × 0.50 = 7.5 Amperes 15\text{ A} \times 0.50 = \mathbf{7.5\text{ Amperes}} 15 A × 0.50 = 7.5 Amperes (900 VA at 120V).

On a 20A circuit: Maximum fastened-in-place load = 20 A × 0.50 = 10.0 Amperes 20\text{ A} \times 0.50 = \mathbf{10.0\text{ Amperes}} 20 A × 0.50 = 10.0 Amperes (1,200 VA at 120V).

30-Ampere Branch Circuits (NEC 210.23(B))

Permitted to supply fixed lighting units with heavy-duty lampholders in other than dwelling units, or utilization equipment in any occupancy.

Any single cord-and-plug connected appliance not fastened in place shall not exceed 80% of the circuit rating ( 30 A × 0.80 = 24.0 Amperes 30\text{ A} \times 0.80 = \mathbf{24.0\text{ Amperes}} 30 A × 0.80 = 24.0 Amperes ).

40-Ampere and 50-Ampere Branch Circuits (NEC 210.23(C))

Permitted to supply cooking appliances fastened in place, infrared heating units, or other utilization equipment. Multi-outlet 40A/50A circuits in dwellings shall not supply general lighting fixtures.

3. Continuous Loads vs. Non-Continuous Loads (NEC 210.19 & 210.20)

The NEC establishes a fundamental distinction between continuous and non-continuous electrical loads based on thermal accumulation inside enclosures and overcurrent devices:

Continuous Load Definition (NEC Article 100): A load where the maximum current is expected to continue for 3 hours or more (e.g., commercial store lighting, office building general illumination, parking lot lighting).

Non-Continuous Load: Any load that operates intermittently for less than 3 hours (e.g., residential kitchen appliances, bathroom exhaust fans, power tools). +-----------------------------------------------------------------------------+

  • | THE 125% CONTINUOUS SIZING RULE |
  • | |
  • | MINIMUM CONDUCTOR AMPACITY (NEC 210.19(A)(1)): |
  • | Ampacity >= (100% of Non-Continuous Load) + (125% of Continuous Load) |
  • | |
  • | MINIMUM OVERCURRENT DEVICE RATING (NEC 210.20(A)): |
  • | OCPD Rating >= (100% of Non-Continuous Load) + (125% of Continuous Load) |
  • | |
  • | EXCEPTION: 100%-rated overcurrent devices and listed assemblies. |
  • +-----------------------------------------------------------------------------+

Worked Calculation Example:

A commercial retail sales floor has 32 Amperes of continuous LED lighting operating 12 hours per day, plus 8 Amperes of non-continuous receptacle loads on the same feeder branch. Minimum Required Rating = ( 8 A × 1.00 ) + ( 32 A × 1.25 ) = 8 A + 40 A = 48.0 Amperes \text{Minimum Required Rating} = (8\text{ A} \times 1.00) + (32\text{ A} \times 1.25) = 8\text{ A} + 40\text{ A} = \mathbf{48.0\text{ Amperes}} Minimum Required Rating = ( 8 A × 1.00 ) + ( 32 A × 1.25 ) = 8 A + 40 A = 48.0 Amperes

Under NEC 240.6, the minimum standard overcurrent protective device required is 50 Amperes , and conductors must have an allowable ampacity of at least 48A before adjustment or correction factors.

4. Multiwire Branch Circuits (NEC 210.4 & 300.13(B))

A multiwire branch circuit consists of two or more ungrounded (hot) conductors that have a voltage between them, and a grounded (neutral) conductor having equal voltage between it and each ungrounded conductor (e.g., two 120V hots sharing a common neutral in a 120/240V 1-phase system, or three 120V hots sharing a neutral in a 120/208V 3-phase Wye system). +-----------------------------------------------------------------------------+

  • | MULTIWIRE BRANCH CIRCUIT SAFETY ARCHITECTURE |
  • | |
  • | [PANELBOARD] |
  • | Phase A (120V Hot 1) ---[ 20A Breaker ]----+ |
  • | |==== (Handle Tie / 2-Pole) |
  • | Phase B (120V Hot 2) ---[ 20A Breaker ]----+ MANDATORY DISCONNECT |
  • | |
  • | Neutral Bar -----------[ Shared White ]==== Grouped with Hots (210.4(D)) |
  • | |
  • | [OUTLET BOX TERMINATION] |
  • | - Neutral MUST be PIGTAILED (NEC 300.13(B)) so removing a receptacle |
  • | does NOT open the neutral path to downstream loads! |
  • +-----------------------------------------------------------------------------+

Critical Rules Governing Multiwire Branch Circuits:

Simultaneous Disconnecting Means (NEC 210.4(B)):

Each multiwire branch circuit shall be provided with a means that will simultaneously disconnect all ungrounded conductors at the point where the branch circuit originates.

Compliant methods: An identified multipole circuit breaker or single-pole breakers connected with UL-listed handle ties. Nails, screws, or unlisted wire ties are strictly prohibited.

Phase Coordination & Neutral Overloading:

Ungrounded conductors must originate from different phases or line buses .

In a 120/240V single-phase system, when Phase A carries 15A and Phase B carries 12A, the neutral carries only the vector difference: I N = ∣ 15 − 12 ∣ = 3 Amperes I_N = |15 - 12| = 3\text{ Amperes} I N ​ = ∣15 − 12∣ = 3 Amperes .

Dangerous Violation: If both hots are landed on the same phase (e.g., via a tandem/twin breaker on a single bus stab), the neutral currents add arithmetically: I N = 15 + 12 = 27 Amperes I_N = 15 + 12 = \mathbf{27\text{ Amperes}} I N ​ = 15 + 12 = 27 Amperes ! This will severely overheat the #12 AWG neutral wire without either 20A breaker ever tripping.

Grouping of Conductors (NEC 210.4(D)):

The ungrounded and grounded circuit conductors of each multiwire branch circuit must be grouped by cable ties or similar means in at least one location within the panelboard or distribution enclosure.

Exception: Grouping is not required if the circuit enters the enclosure as part of a single multiconductor cable assembly (e.g., 12/3 NM-B or MC cable).

Continuity of Grounded Conductor / Device Pigtailing (NEC 300.13(B)):

In multiwire branch circuits, the continuity of a grounded conductor shall not depend on device connections (such as the terminal screws or push-in terminals of a receptacle).

Electricians must splice the neutral conductors together with a pigtail to the receptacle terminal. If the neutral wire were daisy-chained through the receptacle screws and the device removed, the downstream neutral becomes disconnected ("floating neutral"). +-----------------------------------------------------------------------------+

  • | THE DANGEROUS FLOATING NEUTRAL PHENOMENON |
  • | |
  • | [Phase A: 120V] ---> [ 100W Lamp (Z1 = 144 Ohms) ] |
  • | | |
  • | [ OPEN NEUTRAL POINT ] |
  • | | |
  • | [Phase B: 120V] ---> [ 1200W Microwave (Z2 = 12 Ohms) ] |
  • | |
  • | RESULT: Loads are now connected in SERIES across 240 Volts! |
  • | - Current (I) = 240V / (144 + 12) = 1.538 Amps |
  • | - Voltage on 100W Lamp = 1.538 A x 144 Ohms = 221.5 VOLTS! (BURNOUT/FIRE) |
  • | - Voltage on Microwave = 1.538 A x 12 Ohms = 18.5 VOLTS! (UNDERVOLTAGE) |
  • +-----------------------------------------------------------------------------+
  • 5. Branch Circuit Voltage Limitations (NEC 210.6)

To safeguard personnel from high voltage-to-ground shocks in everyday occupancies, NEC 210.6 restricts branch circuit operating voltages:

Dwelling Units & Guest Rooms (210.6(A)): Nominal voltage shall not exceed 120 Volts between conductors supplying luminaires and cord-and-plug loads of 1,440 VA or less, or less than 1/4 horsepower.

Commercial & Industrial Lighting (210.6(C)): Circuits not exceeding 277 Volts to ground are permitted to supply listed luminaires equipped with mogul-base screw shell lampholders or other approved types, mounted not less than 8 feet above the floor (e.g., standard 277V commercial fluorescent and LED fixtures).

Outdoor & High-Mast Lighting (210.6(D)): Circuits up to 600 Volts between conductors are permitted to supply luminaires for lighting outdoor areas (highways, bridges, athletic fields, parking lots) mounted not less than 22 feet high.

6. Conductor Identification Protocols (NEC 210.5 & 200.6)

Proper color coding and identification ensure safe installation and future servicing:

Conductor Role Code Reference Mandatory Identification Method

Grounded (Neutral) NEC 200.6(A) & (B) Continuous white outer finish, continuous gray outer finish, or 3 continuous white or gray stripes along conductor length. For #4 AWG and larger, white/gray tape marking at terminations is permitted.

Equipment Grounding (EGC) NEC 250.119 Bare wire, green insulation, or green insulation with one or more yellow stripes. Green is NEVER permitted for neutral or hot.

Ungrounded (Hot) NEC 210.5(C) Black, Red, Blue (standard 120/208V) or Brown, Orange, Yellow (standard 277/480V). Phase identification must be posted at each panelboard.

Loading diagram... Multiwire Branch Circuit Safety & Compliance Decision Tree (NEC 210.4 & 300.13)