Study guide
4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8)
Oklahoma Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety
1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection
2 Chapter 2: General Electrical Theory & Calculations
2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments
3 Chapter 3: General Installation Requirements (NEC Article 110)
3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable
4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)
4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)
5 Chapter 5: Services & Service Equipment (NEC Article 230)
5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)
6 Chapter 6: Electrical Load Calculations (NEC Article 220)
6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)
7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)
7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)
8 Chapter 8: Grounding and Bonding (NEC Article 250)
8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)
9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)
9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)
10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems
10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)
11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)
11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)
12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)
12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)
13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)
13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)
14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems
14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)
4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8)
Key Takeaways Explain This Topic AI
A Class A GFCI protects people, tripping when ground-fault current reaches 4 to 6 milliamperes in about 25 milliseconds; GFPE devices at 30 mA and above protect equipment, not personnel.
NEC 210.8(A) requires GFCI protection for 125-volt through 250-volt receptacles in dwelling bathrooms, garages and accessory buildings, outdoors, crawl spaces, basements, kitchens, laundry areas, and within 6 feet of a sink, bathtub, or shower stall.
NEC 210.8(B)(2) requires GFCI protection for all 125-volt through 250-volt receptacles installed in a commercial kitchen regardless of distance from a sink, while the 6-foot proximity rule applies to other non-dwelling sinks.
The 6-foot measurement in 210.8 is the shortest path an appliance supply cord would follow without piercing a floor, wall, ceiling, fixed barrier, or fixed doorway — never a straight line through cabinetry.
Oklahoma modified 210.8(F) through OAC 748:20-10-8: outdoor dwelling outlets on single-phase circuits rated 150 volts or less to ground and 50 amperes or less require GFCI protection, but Exception No. 2 for listed HVAC equipment was made permanent by deleting its expiration date.
Last updated: August 2026
Ground-Fault Circuit-Interrupter (GFCI) Protection (NEC 210.8)
Ground-Fault Circuit-Interrupters (GFCIs) are life-safety devices designed to protect human beings from lethal electric shocks caused by current leaking to ground through a person's body. Standard overcurrent protective devices (15A or 20A circuit breakers) protect conductors from overheating and short circuits, but 100 milliamperes (0.1A) is more than enough current to induce fatal ventricular fibrillation in a human heart. NEC 210.8 establishes mandatory GFCI protection across residential, commercial, and industrial occupancies.
1. Operating Principles of Class A GFCI Devices
A Class A GFCI device incorporates a differential current sensing transformer that continuously monitors the current flowing out on the ungrounded (hot) conductor and returning on the grounded (neutral) conductor. +-----------------------------------------------------------------------------+
- | CLASS A GFCI OPERATIONAL MECHANISM |
- | |
- | [Hot Conductor (I_hot)] ==========================> [Load / Appliance] |
- | ( ) Current Transformer |
- | [Neutral Conductor (I_neut)] <======================= [Load / Appliance] |
- | |
- | NORMAL STATE: |
- | I_hot - I_neut = 0 Amperes (Magnetic flux cancels in transformer core). |
- | |
- | GROUND FAULT STATE: |
- | Current leaks through human to earth (I_fault = 4 to 6 mA). |
- | I_hot - I_neut = I_fault >= 5 mA. |
- | Differential flux induces secondary voltage -> Tripping relay opens in |
- | 1/40th of a second (approx. 25 milliseconds)! |
- +-----------------------------------------------------------------------------+
Critical Technical Specifications:
Trip Threshold: Trips when fault current to ground exceeds 4 to 6 milliamperes (nominal design trip rating is 5 mA ).
Response Speed: UL 943 caps the clearing time on a curve that tightens as fault current rises, T = (20 ÷ I)^1.43 seconds with I in milliamperes. At the fault currents of a real line-to-earth contact that works out to roughly 25 milliseconds (1/40 of a second, about 1.5 AC cycles), cutting current off before the cardiac cycle can be driven into ventricular fibrillation; near the 4–6 mA threshold the permitted time is longer.
Readily Accessible Mandate (NEC 210.8): All GFCI test and reset mechanisms must be readily accessible . They cannot be installed behind refrigerators, above drop ceilings requiring a ladder, or behind locked access panels.
2. Dwelling Unit GFCI Requirements (NEC 210.8(A))
In dwelling units, all 125-volt through 250-volt receptacles supplied by single-phase branch circuits rated 150 volts or less to ground installed in the following locations must have GFCI protection:
Bathrooms (210.8(A)(1)): All receptacles in bathrooms without exception.
Garages & Accessory Buildings (210.8(A)(2)): Garages and accessory buildings with floors at or below grade level (including dedicated freezer or garage door opener outlets).
Outdoors (210.8(A)(3)): All outdoor receptacles, including those installed under eaves, on decks, or porches.
Crawl Spaces (210.8(A)(4)): At or below grade level.
Basements (210.8(A)(5)): Finished and unfinished basements (including sump pump and workshop receptacles).
Kitchens (210.8(A)(6)): All receptacles serving countertop surfaces, plus any other receptacle installed within 6 feet of the sink.
Sinks (210.8(A)(7)): Where receptacles are installed within 1.8 m (6 ft) from the top inside edge of the bowl of any sink (wet bar, utility, garage, laundry sink).
Boathouses (210.8(A)(8)): All receptacles in boathouses.
Bathtubs & Shower Stalls (210.8(A)(9)): Receptacles installed within 1.8 m (6 ft) of the outside edge of the bathtub or shower stall.
Laundry Areas (210.8(A)(10)): All receptacles in laundry rooms and laundry areas.
Indoor Damp & Wet Locations (210.8(A)(11)): Indoor pool rooms, car washing bays, greenhouse potting sheds. +-----------------------------------------------------------------------------+
- | MEASURING THE 6-FOOT SINK DISTANCE RULE (NEC 210.8) |
- | |
- | The distance is measured as the SHORTEST PATH an appliance supply cord |
- | would follow without piercing a floor, wall, ceiling, or fixed doorway. |
- | |
- | [Receptacle] <==== (Flexible Cord Path along Counter/Wall) ====> [Sink] |
- | |
- | - Doorway Rule: If a doorway with a hinged door separates the space, the |
- | measurement path extends through the door opening. |
- | - Pass-Through Rule: Measuring directly through a wall or cabinet back is |
- | STRICTLY PROHIBITED. |
- +-----------------------------------------------------------------------------+
- 3. Non-Dwelling / Commercial GFCI Requirements (NEC 210.8(B))
In other than dwelling units (commercial, industrial, institutional facilities), all 125-volt through 250-volt receptacles supplied by single-phase circuits rated 150V or less to ground, 50A or less, and three-phase circuits rated 150V or less to ground, 100A or less, must have GFCI protection in:
Bathrooms: All commercial public and employee restrooms.
Commercial Kitchens: Any kitchen or food preparation area (all receptacles, including under-counter, island, and wall outlets regardless of sink distance).
Buffets & Beverage Service Areas: Where receptacles serve beverage dispensers or warming stations.
Rooftops: All rooftop receptacles (including HVAC service receptacles required by 210.63).
Outdoors: All outdoor commercial receptacles.
Sinks: Within 6.0 feet (1.8 m) of the top inside edge of any sink.
Indoor Damp / Wet Locations: Washdown rooms, commercial car washes, brewery cellars.
Locker Rooms: Locker rooms with associated showering facilities.
Garages & Service Bays: Commercial automotive repair shops, tire service centers, lube bays.
4. Specific Appliance GFCI Protection (NEC 210.8(D))
NEC 210.8(D) mandates GFCI protection for specific appliances in both dwelling and non-dwelling occupancies, whether supplied by a receptacle outlet or hardwired directly : +-----------------------------------------------------------------------------+
- | SPECIFIC APPLIANCES REQUIRING GFCI (NEC 210.8(D)) |
- | |
- | - Automotive vacuum machines - Commercial drinking fountains |
- | - High-pressure spray washers - Tire inflation machines |
- | - Vending machines - Sump pumps |
- | - Dishwashers (residential/comm.) - Electric ranges & cooktops |
- | - Wall-mounted ovens - Clothes dryers |
- | - Microwave ovens - Beverage dispensing equipment |
- +-----------------------------------------------------------------------------+
- 5. Outdoor Dwelling Unit Outlets & HVAC Equipment (NEC 210.8(F))
In Oklahoma, read 210.8(F) as the OUBCC adopted it, not as NFPA printed it. OAC 748:20-10-8 modifies this subsection, and the modification changes the answer for the single most common outdoor dwelling load in the state.
The Oklahoma text requires GFCI protection for all outdoor outlets for dwellings, other than those covered in 210.8(A) Exception No. 1, supplied by single-phase branch circuits rated 150 volts or less to ground and 50 amperes or less , and it names three locations explicitly:
- Garages that have floors located at or below grade
- Accessory buildings
- Boathouses
It also provides that where equipment supplied by such an outlet is replaced , the outlet must then be provided with GFCI protection.
Oklahoma exception Effect
Exception No. 1 GFCI protection is not required on lighting outlets other than those covered by 210.8(C).
Exception No. 2 GFCI protection is not required for listed HVAC equipment . Oklahoma deleted the expiration date that the national text attached to this exception, so it does not sunset here.
Important
The outdoor condenser question is an Oklahoma-specific answer. A listed outdoor air-conditioning condensing unit or heat pump at a dwelling falls under Exception No. 2 and does not require GFCI protection in Oklahoma. Candidates who study a national course will answer this backwards. Section 1.6 covers the amendment and its companion, the added 422.16(B)(5) gas-furnace cord allowance, in full.
Everything not covered by an exception still needs protection: outdoor receptacles, outlets in an at-or-below-grade garage, outlets in accessory buildings and boathouses, and any outlet whose supplied equipment is replaced..