Study guide

6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III)

Oklahoma Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety

1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection

2 Chapter 2: General Electrical Theory & Calculations

2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments

3 Chapter 3: General Installation Requirements (NEC Article 110)

3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable

4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)

4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)

5 Chapter 5: Services & Service Equipment (NEC Article 230)

5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)

6 Chapter 6: Electrical Load Calculations (NEC Article 220)

6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)

7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)

7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)

8 Chapter 8: Grounding and Bonding (NEC Article 250)

8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)

9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)

9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)

10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems

10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)

11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)

11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)

12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)

12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)

13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)

13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)

14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems

14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)

6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III)

Key Takeaways Explain This Topic AI

The Standard Calculation method (NEC Article 220 Part III) requires evaluating each appliance and load category through specific dedicated code sections and distinct demand factors.

Under NEC 220.53, a 75% demand factor is applied to the nameplate ratings when four or more fastened-in-place appliances are served by the same feeder or service, strictly excluding electric ranges, clothes dryers, space heating, and air conditioning.

Electric clothes dryers are sized under NEC 220.54 at 5,000 VA or the nameplate rating (whichever is larger), with Table 220.54 applying a 100% demand factor for 1 to 4 dwelling dryers.

Household electric ranges rated up to 12 kW are sized using Table 220.55 Column C at 8,000 VA (8 kW); for ranges exceeding 12 kW through 27 kW, Note 1 mandates adding 5% to 8 kW for each kilowatt or major fraction thereof exceeding 12 kW.

Non-coincident loads (NEC 220.60) permit comparing heating and air conditioning and omitting the smaller load; feeder neutral conductors (NEC 220.61) apply a 70% demand factor to electric range and dryer loads and a 70% factor to the portion of neutral current exceeding 200A.

Last updated: August 2026

Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III)

The Standard Calculation method set forth in NEC Article 220 Part III is the traditional, universal procedure for sizing residential feeders and service entrance conductors. Unlike optional calculation methods that group loads into broad aggregates, the Part III Standard Method requires the electrician to break the installation into discrete functional categories, apply specific demand tables to each, evaluate non-coincident loads, and compute separate line and neutral ampacities.

1. The Standard Calculation Step-by-Step Architecture

A complete Part III standard calculation follows a rigorous 6-step procedure : +-----------------------------------------------------------------------------+

  • | NEC ARTICLE 220 PART III STANDARD CALCULATION STEPS |
  • | |
  • | [STEP 1: General Lighting, Small Appliance & Laundry (220.41 & 220.52)]|
  • | • Floor Area × 3 VA/sq ft + (Small Appliance × 1,500) + (Laundry × 1,500) |
  • | • Apply NEC Table 220.45 Demand (First 3k @ 100%, 3k-120k @ 35%) |
  • | |
  • | [STEP 2: Fixed Fastened-in-Place Appliances (NEC 220.53)] |
  • | • Sum water heater, dishwasher, disposal, microwave, trash compactor, etc.|
  • | • If 4 or MORE fastened-in-place units -> Apply 75% Demand Factor |
  • | • Excludes: Ranges, Dryers, Space Heating, Air Conditioning |
  • | |
  • | [STEP 3: Electric Clothes Dryer (NEC 220.54 & Table 220.54)] |
  • | • 5,000 VA minimum or nameplate rating (whichever is larger) |
  • | • 1 to 4 dryers = 100% Demand Factor |
  • | |
  • | [STEP 4: Household Electric Cooking Appliances (NEC 220.55 & Table 220.55)]|
  • | • Single range ≤ 12 kW = 8,000 VA (Column C) |
  • | • Range > 12 kW -> Add 5% to 8 kW for each kW exceeding 12 kW (Note 1) |
  • | |
  • | [STEP 5: Non-Coincident Loads & Largest Motor (NEC 220.60 & 220.18)] |
  • | • Compare Electric Space Heating vs. Air Conditioning -> Take LARGER only |
  • | • Add 25% of the largest motor rating (compressor or pump) |
  • | |
  • | [STEP 6: Total Service Amperage & Neutral Sizing (NEC 220.61)] |
  • | • Total Calculated Line Amps = Total Line VA / 240V |
  • | • Neutral Load: Net 120V Loads + (Range × 70%) + (Dryer × 70%) |
  • | • Apply 70% Neutral Demand to excess over 200 Amperes |
  • +-----------------------------------------------------------------------------+
  • 2. Fixed Fastened-in-Place Appliances (NEC 220.53)

NEC 220.53 permits a 75 % 75\% 75% demand factor ( 0.75 0.75 0.75 ) to be applied to the total nameplate rating of fixed appliances if four (4) or more appliances are served by the same feeder or service.

Qualifying vs. Excluded Appliances under NEC 220.53:

Qualifying Appliances: Electric water heater, dishwasher, food waste disposal, built-in microwave, trash compactor, attic ventilation fan, central vacuum system, electric pool pump, sump pump, and instant hot water dispenser.

Strictly Excluded Appliances (Never derated under 220.53):

Household electric cooking equipment (ranges, cooktops, ovens — sized under 220.55).

Electric clothes dryers (sized under 220.54).

Electric space heating equipment (sized under 220.51 / 220.60).

Air-conditioning equipment (sized under Article 440 / 220.60).

Example Rule Application: If a house has 3 qualifying fixed appliances (water heater, dishwasher, disposal), they must be calculated at 100 % 100\% 100% nameplate rating . If a 4th appliance (e.g., built-in microwave) is present, all four appliances are summed and multiplied by 0.75 0.75 0.75 .

3. Electric Clothes Dryers (NEC 220.54)

Electric clothes dryer load calculations must comply with NEC 220.54 :

Minimum Rating: The load must be calculated at 5 , 000 VA 5,000\text{ VA} 5 , 000 VA or the nameplate rating , whichever is larger.

If a residential dryer has a nameplate rating of 4 , 500 VA 4,500\text{ VA} 4 , 500 VA , it must be calculated at 5 , 000 VA 5,000\text{ VA} 5 , 000 VA .

If a heavy-duty dryer has a nameplate rating of 6 , 200 VA 6,200\text{ VA} 6 , 200 VA , it is calculated at 6 , 200 VA 6,200\text{ VA} 6 , 200 VA .

Demand Factors (Table 220.54): For 1 to 4 dryers, the demand factor is 100 % 100\% 100% . For multi-family installations with 5 or more dryers, demand factors scale downward (e.g., 5 dryers = 85%, 6 dryers = 75%, 7 dryers = 65%).

4. Household Cooking Appliances (NEC 220.55 & Table 220.55)

NEC Table 220.55 governs household electric ranges, wall-mounted ovens, counter-mounted cooktops, and other household cooking appliances exceeding 1.75 kW 1.75\text{ kW} 1.75 kW rating. +-----------------------------------------------------------------------------+

  • | NEC TABLE 220.55 DEMAND SIZING SUMMARY (COLUMN C) |
  • | |
  • | NUMBER OF RANGES MAXIMUM RATING COLUMN C DEMAND |
  • | ----------------------------------------------------------------------- |
  • | 1 Range Not over 12 kW 8 kW (8,000 VA) |
  • | 2 Ranges Not over 12 kW 11 kW (11,000 VA) |
  • | 3 Ranges Not over 12 kW 14 kW (14,000 VA) |
  • | 4 Ranges Not over 12 kW 17 kW (17,000 VA) |
  • | 5 Ranges Not over 12 kW 20 kW (20,000 VA) |
  • +-----------------------------------------------------------------------------+

Sizing Ranges Over 12 kW (Table 220.55 Note 1):

For ranges rated over 12 kW 12\text{ kW} 12 kW through 27 kW 27\text{ kW} 27 kW , the Column C demand value must be increased by 5 % 5\% 5% for each additional kilowatt (or major fraction thereof, ≥ 0.5 kW \ge 0.5\text{ kW} ≥ 0.5 kW ) by which the rating exceeds 12 kW 12\text{ kW} 12 kW . Demand (kW) = 8 kW + [ 8 kW × 0.05 × ( Range Rating in kW − 12 ) ] \text{Demand (kW)} = 8\text{ kW} + \left[ 8\text{ kW} \times 0.05 \times (\text{Range Rating in kW} - 12) \right] Demand (kW) = 8 kW + [ 8 kW × 0.05 × ( Range Rating in kW − 12 ) ]

Worked Range Examples:

14 kW Range: Exceeds 12 kW by 2 kW 2\text{ kW} 2 kW . Increase = 2 × 5 % = 10 % 2 \times 5\% = 10\% 2 × 5% = 10% . Demand = 8 kW × 1.10 = 8.8 kW = 8 , 800 VA 8\text{ kW} \times 1.10 = 8.8\text{ kW} = 8,800\text{ VA} 8 kW × 1.10 = 8.8 kW = 8 , 800 VA .

16 kW Range: Exceeds 12 kW by 4 kW 4\text{ kW} 4 kW . Increase = 4 × 5 % = 20 % 4 \times 5\% = 20\% 4 × 5% = 20% . Demand = 8 kW × 1.20 = 9.6 kW = 9 , 600 VA 8\text{ kW} \times 1.20 = 9.6\text{ kW} = 9,600\text{ VA} 8 kW × 1.20 = 9.6 kW = 9 , 600 VA .

16.6 kW Range: Exceeds 12 kW by 4.6 kW 4.6\text{ kW} 4.6 kW (rounds to 5 kW 5\text{ kW} 5 kW major fraction). Increase = 5 × 5 % = 25 % 5 \times 5\% = 25\% 5 × 5% = 25% . Demand = 8 kW × 1.25 = 10.0 kW = 10 , 000 VA 8\text{ kW} \times 1.25 = 10.0\text{ kW} = 10,000\text{ VA} 8 kW × 1.25 = 10.0 kW = 10 , 000 VA .

Separate Ovens and Cooktops (Table 220.55 Note 4):

Where a branch circuit or feeder supplies one counter-mounted cooktop and not more than two wall-mounted ovens in the same room, their nameplate ratings are added together, and the total is treated as a single range under Table 220.55.

5. Non-Coincident Loads (NEC 220.60)

Where it is unlikely that two dissimilar loads will be operated simultaneously, NEC 220.60 permits calculating only the largest load and omitting the smaller:

Electric Space Heating vs. Air Conditioning: Compare the total heating load against the total air conditioning load. Include 100 % 100\% 100% of the larger load and drop the smaller load entirely from the calculation.

Example: A home has a 10 kW 10\text{ kW} 10 kW central electric furnace and a 4.5 kW 4.5\text{ kW} 4.5 kW ( 18.75 A @ 240 V 18.75\text{A} @ 240\text{V} 18.75 A @240 V ) air conditioning unit. Electric heat ( 10 , 000 VA 10,000\text{ VA} 10 , 000 VA ) is larger than air conditioning ( 4 , 500 VA 4,500\text{ VA} 4 , 500 VA ). The 10 , 000 VA 10,000\text{ VA} 10 , 000 VA heating load is included in the service calculation, and the 4 , 500 VA 4,500\text{ VA} 4 , 500 VA AC load is omitted.

6. Service & Feeder Neutral Load Calculations (NEC 220.61)

The service/feeder neutral conductor carries only the maximum unbalanced load between the neutral and any one ungrounded conductor. +-----------------------------------------------------------------------------+

  • | NEC 220.61 NEUTRAL SIZING RULES |
  • | |
  • | [100% UNBALANCED 120V LOADS] |
  • | • General lighting, small appliance, and laundry calculated demand load. |
  • | • 100% of 120V fixed appliances (dishwasher, disposal, microwave). |
  • | |
  • | [70% DEMAND FACTOR REDUCTIONS (220.61(B))] |
  • | • Household Electric Ranges: Calculated demand (220.55) × 70% (0.70). |
  • | • Electric Clothes Dryers: Calculated demand (220.54) × 70% (0.70). |
  • | • 200A Neutral Threshold: The portion of neutral load over 200A is derated|
  • | by 70% for 3-wire 120/240V single-phase systems. |
  • | |
  • | [PURE 240V LOADS (NO NEUTRAL CONNECTION)] |
  • | • 240V Water Heaters, 240V AC Compressors, 240V Baseboard Heaters = 0 VA. |
  • +-----------------------------------------------------------------------------+
  • 7. Complete Worked Standard Calculation: 2,400 sq ft Home

Single-Family Dwelling Parameters:

Living Area: 2 , 400 sq ft 2,400\text{ sq ft} 2 , 400 sq ft

Dedicated Circuits: 2 Small Appliance ( 1 , 500 VA 1,500\text{ VA} 1 , 500 VA each), 1 Laundry ( 1 , 500 VA 1,500\text{ VA} 1 , 500 VA )

Fixed Fastened-in-Place Appliances (4 units):

  • Water Heater ( 240 V 240\text{V} 240 V ): 4 , 500 VA 4,500\text{ VA} 4 , 500 VA
  • Dishwasher ( 120 V 120\text{V} 120 V ): 1 , 200 VA 1,200\text{ VA} 1 , 200 VA
  • Garbage Disposal ( 120 V 120\text{V} 120 V ): 900 VA 900\text{ VA} 900 VA
  • Microwave Hood ( 120 V 120\text{V} 120 V ): 1 , 400 VA 1,400\text{ VA} 1 , 400 VA
  • Electric Clothes Dryer: 5.0 kW 5.0\text{ kW} 5.0 kW nameplate ( 5 , 000 VA 5,000\text{ VA} 5 , 000 VA )

Household Electric Range: 12.0 kW 12.0\text{ kW} 12.0 kW nameplate ( 12 , 000 VA 12,000\text{ VA} 12 , 000 VA )

HVAC Equipment: Central Air Conditioning ( 4 , 500 VA 4,500\text{ VA} 4 , 500 VA ) vs. Electric Furnace ( 10 , 000 VA 10,000\text{ VA} 10 , 000 VA )

Largest Motor: Disposal motor ( 900 VA 900\text{ VA} 900 VA ) -> 25 % 25\% 25% addition = 225 VA 225\text{ VA} 225 VA ===============================================================================

  • PART III STANDARD CALCULATION WORKSHEET
  • ===============================================================================

1. GENERAL LIGHTING & APPLIANCE LOAD (Table 220.45):

  • General Lighting: 2,400 sq ft × 3 VA/sq ft = 7,200 VA
  • Small Appliance Circuits: 2 × 1,500 VA = 3,000 VA
  • Laundry Branch Circuit: 1 × 1,500 VA = 1,500 VA
  • --------------------------------------------------------------
  • Total Connected General Load = 11,700 VA

Apply Table 220.45 Demand Factors:

  • First 3,000 VA @ 100% = 3,000 VA
  • Remaining 8,700 VA (11,700 - 3,000) @ 35% = 3,045 VA
  • --------------------------------------------------------------
  • > Net General Lighting & Appliance Load = 6,045 VA

2. FIXED FASTENED-IN-PLACE APPLIANCES (NEC 220.53):

  • Water Heater = 4,500 VA
  • Dishwasher = 1,200 VA
  • Garbage Disposal = 900 VA
  • Microwave Hood = 1,400 VA
  • --------------------------------------------------------------
  • Total Connected Fixed Load = 8,000 VA
  • Apply 75% Demand Factor (4 appliances): 8,000 × 0.75 = 6,000 VA
  • > Net Fixed Appliance Load = 6,000 VA

3. ELECTRIC CLOTHES DRYER (NEC 220.54):

  • 5,000 VA nameplate (min 5,000 VA) @ 100% demand = 5,000 VA
  • > Net Clothes Dryer Load = 5,000 VA

4. HOUSEHOLD ELECTRIC RANGE (NEC 220.55 & Table 220.55):

  • 12 kW Range -> Column C Demand = 8,000 VA
  • > Net Electric Range Load = 8,000 VA

5. NON-COINCIDENT HVAC LOADS (NEC 220.60):

  • Central Air Conditioning: 4,500 VA
  • Electric Heating: 10,000 VA
  • Select LARGER load (Electric Heat @ 100%) = 10,000 VA
  • > Net Space Heating Load = 10,000 VA

6. LARGEST MOTOR ADDITION (NEC 220.14(C) / 430.24):

  • 25% of largest motor (Disposal: 900 VA × 0.25) = 225 VA
  • > Net Largest Motor Addition = 225 VA
  • ===============================================================================
  • TOTAL CALCULATED SERVICE LOAD (VA) = 35,270 VA

MINIMUM SERVICE ENTRANCE AMPACITY (120/240V Single-Phase):

  • Current (Amperes) = 35,270 VA / 240 Volts = 146.96 Amperes
  • Standard Service Equipment Rating: 150A or 200A Service
  • ===============================================================================

7. SERVICE NEUTRAL LOAD CALCULATION (NEC 220.61):

  • Net General Lighting & Appliance Load = 6,045 VA
  • 120V Fixed Appliances (1,200 + 900 + 1,400) × 0.75 = 2,625 VA
  • Electric Clothes Dryer (5,000 VA × 70%) = 3,500 VA
  • Household Electric Range (8,000 VA × 70%) = 5,600 VA
  • 240V Loads (Water Heater, Electric Heat) = 0 VA
  • --------------------------------------------------------------
  • Total Calculated Neutral Load = 17,770 VA

Calculated Neutral Current = 17,770 VA / 240V = 74.04 Amperes

(Since neutral current is under 200A, the 200A derating does not apply).

===============================================================================

Loading diagram... NEC Part III Standard Dwelling Unit Calculation Methodology