Study guide

8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66)

Oklahoma Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety

1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection

2 Chapter 2: General Electrical Theory & Calculations

2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments

3 Chapter 3: General Installation Requirements (NEC Article 110)

3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable

4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)

4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)

5 Chapter 5: Services & Service Equipment (NEC Article 230)

5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)

6 Chapter 6: Electrical Load Calculations (NEC Article 220)

6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)

7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)

7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)

8 Chapter 8: Grounding and Bonding (NEC Article 250)

8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)

9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)

9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)

10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems

10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)

11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)

11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)

12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)

12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)

13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)

13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)

14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems

14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)

8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66)

Key Takeaways Explain This Topic AI

NEC 250.50 mandates that all grounding electrodes specified in NEC 250.52(A)(1) through (A)(7) that are present at each building or structure served must be bonded together to form the Grounding Electrode System (GES).

Permitted grounding electrodes under NEC 250.52(A) include 10+ ft metal underground water pipes, concrete-encased electrodes (Ufer grounds with 20+ ft of #4 Cu or 1/2 in. rebar), ground rings (20+ ft of #2 Cu at 30+ in. depth), 8-ft rod/pipe electrodes, plate electrodes, and other listed grounding assemblies.

Under NEC 250.68(C)(1), interior metal water piping located more than 5 feet (1.5 m) from the point of entrance into the building shall NOT be used as part of the grounding electrode system or to interconnect electrodes.

NEC 250.53(A)(2)–(3) dictates that a single ground rod, pipe, or plate electrode with a resistance to earth exceeding 25 ohms MUST be supplemented by one additional electrode spaced not less than 6 feet (1.8 m) apart; once supplemented, no further resistance testing is required.

Grounding Electrode Conductors (GECs) are sized using NEC Table 250.66 based on the largest ungrounded service conductor, but sole connections to specific electrodes have maximum size caps: #6 AWG copper for rod/pipe/plate electrodes (250.66(A)), #4 AWG copper for concrete-encased electrodes (250.66(B)), and #2 AWG copper for ground rings (250.66(C)).

Last updated: August 2026

Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66)

The Grounding Electrode System (GES) establishes the direct physical interface between a premises electrical installation and the earth. Its function is to dissipate lightning energy, drain external utility surges, and clamp the premises electrical system voltage to a stable earth potential. On the Oklahoma Journeyman examination, sizing the Grounding Electrode Conductor (GEC) using NEC Table 250.66 and understanding the specific electrode construction standards under NEC 250.52 are heavily tested competencies.

1. The Grounding Electrode System Rule (NEC 250.50)

NEC 250.50 sets forth the mandatory requirement for establishing a comprehensive grounding electrode network:

"All grounding electrodes as described in 250.52(A)(1) through (A)(7) that are present at each building or structure served shall be bonded together to form the grounding electrode system."

If none of the primary electrodes exist (such as in an existing building with all-plastic underground plumbing and no accessible foundation rebar), one or more of the electrodes described in 250.52(A)(4) through (A)(8) (such as driven ground rods or a ground ring) must be installed and bonded together. +---------------------------------------------------------------------------------------------------+

  • | GROUNDING ELECTRODE SYSTEM (GES) BONDING MATRIX |
  • | |
  • | +-------------------------------------+ |
  • | | SERVICE DISCONNECT / GEC TERMINAL | |
  • | +------------------+------------------+ |
  • | | |
  • | +-------------------+-----------------+-------------------+-------------------+ |
  • | | (GEC per T250.66) | (Max #4 Cu) | (Max #6 Cu) | (Max #2 Cu) | (T250.66) |
  • | v v v v v |
  • | +-----------+ +--------------+ +-----------+ +--------------+ +------------+ |
  • | | Metal | | Concrete- | | Driven | | Ground Ring | | Structural | |
  • | | Water | | Encased | | Ground | | (20 ft #2 Cu | | Metal | |
  • | | Pipe | | Ufer Ground | | Rods | | @ 30 in deep)| | Building | |
  • | | (≥10 ft) | | (20 ft rebar)| | (8 ft rod)| +--------------+ | Frame | |
  • | +-----+-----+ +--------------+ +-----+-----+ +------------+ |
  • | | | |
  • | +====== SUPPLEMENTAL BOND ===========+ |
  • | (NEC 250.53(D)(2)) |
  • +---------------------------------------------------------------------------------------------------+
  • 2. Permitted Grounding Electrodes (NEC 250.52(A))

NEC 250.52(A) defines the physical characteristics and dimensional requirements of qualifying electrodes:

1. Metal Underground Water Pipe (NEC 250.52(A)(1))

Earth Contact: Must be in direct contact with the earth for 10 feet (3.0 m) or more (including any metal well casing bonded to the pipe).

The 5-Foot Interior Rule (NEC 250.68(C)(1)): The connection of the GEC to a metal underground water pipe electrode must be made within 5 feet (1.5 m) of the point of entrance of the pipe into the building. Interior metal water piping beyond 5 feet shall NOT be used as part of the GES because downstream maintenance may replace copper pipes with PEX or PVC.

Mandatory Supplemental Electrode (NEC 250.53(D)(2)): A metal underground water pipe electrode must always be supplemented by an additional electrode (such as a concrete-encased electrode, ground ring, or driven ground rod). If the supplemental electrode is a ground rod, pipe, or plate, it must comply with the 25-ohm resistance rule.

2. Concrete-Encased Electrode / "Ufer Ground" (NEC 250.52(A)(3))

Consists of at least 20 feet (6.0 m) of either:

One or more bare or zinc-galvanized or electrically conductive coated steel reinforcing bars or rods of not less than 1/2 inch (13 mm) in diameter (tied together by standard steel tie wire), OR

Bare copper conductor not smaller than #4 AWG .

Encased by at least 2 inches (50 mm) of concrete, located horizontally or vertically near the bottom of a concrete foundation or footing that is in direct contact with the earth.

Note: In modern construction with concrete footings containing rebar, the concrete-encased electrode is mandatory and forms one of the lowest-impedance, most reliable electrodes available.

3. Ground Ring (NEC 250.52(A)(4))

Encircles the building or structure in direct contact with the earth.

Consists of at least 20 feet (6.0 m) of bare copper conductor not smaller than #2 AWG .

Buried at a depth below the earth's surface of not less than 30 inches (750 mm) .

4. Rod and Pipe Electrodes (NEC 250.52(A)(5) & 250.53(A))

Length: Minimum 8 feet (2.44 m) of rod length in direct contact with the soil.

Diameter: Listed ground rods (copper-coated steel or stainless steel) must have a diameter of not less than 5/8 inch (15.87 mm) (unless specifically listed for smaller diameters, minimum 1/2 in.). Iron or steel pipe electrodes must be not less than 3/4 inch trade size with a galvanized outer coating.

Installation Position (NEC 250.53(G)): Rods must be driven vertically to full 8-foot depth. If rock bottom is encountered, the rod may be driven at an oblique angle not exceeding 45 degrees from the vertical, or buried in a trench that is at least 30 inches (750 mm) deep.

The 25-Ohm Rule & Second Rod Requirement (NEC 250.53(A)(2)–(3)): A single rod electrode that does not have a resistance to earth of 25 ohms or less must be supplemented by one additional electrode. When two rods are installed, they must be spaced not less than 6 feet (1.8 m) apart (spacing equal to rod length, e.g. 8 to 16 feet, yields optimal resistance). Once the second rod is driven, no further resistance measurement is required.

5. Plate Electrodes (NEC 250.52(A)(6))

Must expose not less than 2 square feet (0.186 m²) of surface area to the exterior soil.

Bare steel or iron plates must be at least 1/4 inch (6.4 mm) thick; nonferrous (copper) plates must be at least 0.06 inch (1.5 mm) thick.

Buried at least 30 inches (750 mm) below the surface of the earth. +---------------------------------------------------------------------------------------------------+

  • | PROHIBITED GROUNDING ELECTRODES (NEC 250.52(B)) |
  • | |
  • | 1. Metal Underground Gas Piping Systems: |
  • | - Strictly prohibited from serving as a grounding electrode due to fire and explosion risks. |
  • | |
  • | 2. Aluminum Electrodes: |
  • | - Strictly prohibited in direct earth contact due to rapid galvanic corrosion and oxidation. |
  • +---------------------------------------------------------------------------------------------------+
  • 3. Sizing the Grounding Electrode Conductor (NEC Table 250.66)

The Grounding Electrode Conductor (GEC) connects the service equipment or separately derived system to the grounding electrodes. The baseline GEC size is determined from NEC Table 250.66 based on the total cross-sectional area of the largest ungrounded service-entrance conductor (or equivalent area for parallel sets): +---------------------------------------------------------------------------------------------------+

  • | NEC TABLE 250.66: GROUNDING ELECTRODE CONDUCTOR SIZING |
  • | |
  • | SIZE OF LARGEST UNGROUNDED MINIMUM SIZE OF GROUNDING ELECTRODE CONDUCTOR |
  • | SERVICE-ENTRANCE CONDUCTOR --------------------------------------------- |
  • | COPPER ALUMINUM COPPER (AWG/kcmil) ALUMINUM (AWG/kcmil) |
  • | ----------------------- --------------------- --------------------- --------------------- |
  • | 2 AWG or smaller 1/0 AWG or smaller 8 AWG 6 AWG |
  • | 1 AWG or 1/0 AWG 2/0 AWG or 3/0 AWG 6 AWG 4 AWG |
  • | 2/0 AWG or 3/0 AWG 4/0 AWG or 250 kcmil 4 AWG 2 AWG |
  • | Over 3/0 thru 350 kcmil Over 250 thru 500 kcmil 2 AWG 1/0 AWG |
  • | Over 350 thru 600 kcmil Over 500 thru 900 kcmil 1/0 AWG 3/0 AWG |
  • | Over 600 thru 1100 kcmil Over 900 thru 1750 kcmil 2/0 AWG 4/0 AWG |
  • | Over 1100 kcmil Over 1750 kcmil 3/0 AWG 250 kcmil |
  • +---------------------------------------------------------------------------------------------------+

Sizing for Parallel Service Conductors:

Where service-entrance conductors are installed in parallel in two or more raceways, the equivalent area is calculated by summing the circular mil area of the ungrounded conductors of each phase .

Worked Calculation Example: A 400A service is supplied by two parallel sets of 3/0 AWG copper conductors per phase in two conduits:

Area of 3/0 AWG Copper (from NEC Ch. 9, Table 8) = 167 , 800 cmil 167,800\text{ cmil} 167 , 800 cmil .

Total equivalent area per phase = 167 , 800 × 2 = 335 , 600 cmil 167,800 \times 2 = 335,600\text{ cmil} 167 , 800 × 2 = 335 , 600 cmil ( 335.6 kcmil 335.6\text{ kcmil} 335.6 kcmil ).

Looking up 335.6 kcmil 335.6\text{ kcmil} 335.6 kcmil in Table 250.66 ("Over 3/0 through 350 kcmil"): The required copper GEC to a metal water pipe is #2 AWG Copper .

4. Maximum Required GEC Sizes: The Special Electrode Limits (NEC 250.66(A)–(C))

A critical rule heavily tested on journeyman exams is that where a GEC connects solely to specific manufactured or encased electrodes, the conductor is NOT required to be sized per Table 250.66, but is capped at specific maximum sizes: +---------------------------------------------------------------------------------------------------+

  • | MAXIMUM GEC SIZES TO SPECIFIC ELECTRODES (NEC 250.66(A)-(C)) |
  • | |
  • | ELECTRODE TYPE MAXIMUM COPPER GEC SIZE CODE REFERENCE |
  • | --------------------------------- ------------------------- ------------------------------- |
  • | Rod, Pipe, or Plate Electrode #6 AWG Copper NEC 250.66(A) |
  • | (#4 AWG Aluminum) |
  • | |
  • | Concrete-Encased (Ufer) Electrode #4 AWG Copper NEC 250.66(B) |
  • | (#2 AWG Aluminum) |
  • | |
  • | Ground Ring Conductor #2 AWG Copper NEC 250.66(C) |
  • | (Same size as ring wire) |
  • +---------------------------------------------------------------------------------------------------+

The "Sole Connection" Rule Explained:

If an 800A service has 2 × 500 kcmil Cu 2 \times 500\text{ kcmil Cu} 2 × 500 kcmil Cu conductors per phase ( 1 , 000 kcmil 1,000\text{ kcmil} 1 , 000 kcmil total), Table 250.66 would normally call for a 2/0 AWG Cu GEC.

If this GEC connects to a metal water pipe , it MUST be sized at 2/0 AWG Cu .

If a bonding jumper extends from the water pipe or service panel solely to two driven ground rods , that bonding jumper is never required to be larger than #6 AWG Cu under NEC 250.66(A).

If a conductor connects solely to a concrete-encased foundation rebar electrode , it is never required to be larger than #4 AWG Cu under NEC 250.66(B).

5. Grounding Electrode Conductor Installation & Physical Protection (NEC 250.64)

Continuous Run (NEC 250.64(C)): The GEC must be installed in one continuous length without splices, except where spliced by irreversible compression fittings listed as grounding equipment or by exothermic welding.

Mechanical Protection (NEC 250.64(B)):

#8 AWG Cu: Must be enclosed in rigid metal conduit (RMC), intermediate metal conduit (IMC), Schedule 80 PVC, EMT, or cable armor.

#6 AWG Cu: May be run exposed along the building surface if secured firmly and not exposed to physical damage.

#4 AWG Cu and Larger: May be secured directly to building surfaces without raceway protection where not exposed to severe physical damage.

The Ferrous Enclosure "Choke Effect" Rule (NEC 250.64(E)): Where a GEC is installed inside a ferrous metal raceway (such as steel EMT or RMC), both ends of the metallic raceway must be bonded to the GEC . Failure to bond both ends turns the steel raceway into an inductive choke coil during high-frequency lightning discharges, severely impeding surge current flow.

Loading diagram... Grounding Electrode Conductor (GEC) Sizing & Selection Logic (NEC 250.66)