Study guide
13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550)
Oklahoma Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety
1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection
2 Chapter 2: General Electrical Theory & Calculations
2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments
3 Chapter 3: General Installation Requirements (NEC Article 110)
3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable
4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)
4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)
5 Chapter 5: Services & Service Equipment (NEC Article 230)
5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)
6 Chapter 6: Electrical Load Calculations (NEC Article 220)
6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)
7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)
7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)
8 Chapter 8: Grounding and Bonding (NEC Article 250)
8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)
9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)
9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)
10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems
10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)
11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)
11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)
12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)
12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)
13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)
13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)
14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems
14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)
13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550)
Key Takeaways Explain This Topic AI
Agricultural buildings (NEC Article 547) subject to corrosive animal ammonia fumes, high humidity, and dust require nonmetallic, dusttight, and watertight wiring methods (such as Type UF cable, PVC, RTRC, and NEMA 4X enclosures); standard EMT and NM-B are prohibited.
NEC 547.10 mandates equipotential planes in concrete livestock confinement floors (bonded with min 8 AWG bare copper) to eliminate tingle/stray voltage that reduces milk yields and impairs livestock health.
A voltage gradient transition ramp extending at least 3 feet (900 mm) beyond the confinement entrance is required under NEC 547.10(B) to prevent step-potential shocks as livestock enter or exit.
Service equipment for manufactured and mobile homes (NEC 550.32) must NOT be mounted on or inside the home; it must be installed on an exterior pedestal or pole located within 30 feet of the home exterior wall.
Manufactured home feeders (NEC 550.16 & 550.33) require a 4-wire installation (2 hots, 1 neutral, 1 equipment ground) with the neutral bus strictly ISOLATED from the chassis/enclosure inside the interior distribution panel.
Last updated: August 2026
Agricultural Buildings & Manufactured/Mobile Homes (NEC Articles 547 & 550)
Specialized environmental conditions and structural configurations require tailored electrical installation standards. Agricultural facilities subject livestock and electrical equipment to extreme moisture, corrosive ammonia vapors, and dust, where minute stray voltages can cause livestock distress and severe economic loss. Manufactured and mobile homes present unique grounding and service disconnecting challenges due to their transportable metal frames. NEC Articles 547, 550, and 551 address these critical installations.
1. Agricultural Buildings (NEC Article 547)
NEC Article 547 applies to agricultural structures where excessive dust, dust with water, or corrosive atmospheres exist (e.g., dairy barns, poultry houses, hog confinement buildings, feed storage, and livestock pavilions). +-----------------------------------------------------------------------------+
- | AGRICULTURAL ENVIRONMENTAL HAZARDS (NEC 547.1) |
- | |
- | - Corrosive Ammonia (NH3) & Moisture: Decomposing animal waste creates |
- | corrosive gases that aggressively corrode steel raceways and copper. |
- | - Washdown Sanitization: High-pressure hot water washdowns soak boxes. |
- | - Combustible Dusts: Feed milling, bedding, and dry manure create dust. |
- +-----------------------------------------------------------------------------+
Permitted vs. Prohibited Wiring Methods (NEC 547.5):
Permitted Wiring Methods (547.5(A)):
Type UF (Underground Feeder) Cable and Type USE Cable.
Rigid Polyvinyl Chloride Conduit (PVC - Schedule 40 or 80).
Reinforced Thermosetting Resin Conduit (RTRC).
Liquidtight Flexible Nonmetallic Conduit (LFNC) with listed nonmetallic fittings.
Copper SE (Service-Entrance) Cable.
Prohibited Wiring Methods:
Standard Electrical Metallic Tubing (EMT), galvanized steel conduit, flexible metal conduit (FMC), and Type NM-B (Romex) are strictly prohibited in areas subject to corrosive ammonia fumes.
Boxes, Enclosures & Luminaires (NEC 547.5(C) & 547.8):
All junction boxes, pull boxes, switches, and receptacles must be dusttight and watertight (NEMA 4, 4X, or IP66/67 rated) constructed of nonmetallic or corrosion-resistant materials with gasketed covers.
Luminaires must be sealed, gasketed, and resistant to water spray and corrosive vapors.
2. Equipotential Planes in Livestock Areas (NEC 547.10)
The "Stray Voltage" (Tingle Voltage) Phenomenon:
Dairy cows and livestock have much lower body resistance than humans and are grounded through wet hooves. Voltage differences as low as 0.5 to 1.0 Volt AC between a metal drinking trough/stanchion and the concrete floor can cause cows to receive painful shocks.
Affected animals refuse to drink water, stop eating, develop mastitis, and experience steep drops in milk production. +-----------------------------------------------------------------------------+
- | EQUIPOTENTIAL PLANE ARCHITECTURE (NEC 547.10) |
- | |
- | [EQUIPOTENTIAL PLANE (547.10(A))] |
- | - Welded wire mesh or bonded grid embedded in concrete floor slab. |
- | - Bonded with minimum #8 AWG SOLID BARE COPPER conductor. |
- | - Connected to all metal stanchions, water bowls, and electrical grounds. |
- | *Ensures the cow's hooves and mouth are at the EXACT SAME POTENTIAL (0V)! |
- | |
- | [VOLTAGE GRADIENT TRANSITION RAMP (NEC 547.10(B))] |
- | - As animals walk from unbonded soil/gravel onto the equipotential floor, |
- | a dangerous step-potential shock occurs at the boundary line. |
- | - MANDATE: A voltage gradient transition plane must extend at least |
- | 3.0 FEET (900 mm) outward into the dirt/gravel approach ramp. |
+-----------------------------------------------------------------------------+ +-----------------------------------------------------------------------------+
- | LIVESTOCK ENTRANCE TRANSITION RAMP DETAIL |
- | |
- | Equipotential Barn Floor Exterior Dirt / Gravel Path |
- | +==============================+ --------------------------------- |
- | | Bonded Concrete Floor Slab | |
- | | (Embedded 8 AWG Wire Mesh) | \ Transition Ramp Grid |
- | +==============================+ \ (Extends Min 3 ft Outward |
- | \ sloped at 45 degrees) |
- | <------- INSIDE BARN --------> | <--- 3 FT TRANSITION ---> | OUTSIDE |
- +-----------------------------------------------------------------------------+
- 3. Manufactured Homes & Mobile Homes (NEC Article 550)
NEC Article 550 governs factory-assembled transportable structures built on permanent steel chassis.
Service Equipment Location (NEC 550.32(A))
Prohibition on Structure Mounting: Service equipment (utility meter base and main service disconnecting means) shall NOT be mounted on or in a manufactured home .
Pedestal / Pole Mounting: The service equipment must be installed on a separate pedestal, pole, or adjacent substantial structure.
Proximity Rule: The service equipment must be installed in sight from and not more than 30 feet (9.0 m) from the exterior wall of the manufactured home.
Rationale: Movement and chassis flex during transport, high wind vibrations, and emergency first-responder disconnect accessibility. +-----------------------------------------------------------------------------+
- | MANUFACTURED HOME SERVICE PEDESTAL & 4-WIRE FEEDER |
- | |
- | [OUTDOOR SERVICE PEDESTAL] (Max 30 ft away) |
- | - Meter Base + Main Service Disconnect (e.g., 200A) |
- | - Main Bonding Jumper (MBJ) connects Neutral to Grounding Electrode |
- | |
- | =================== 4-WIRE FEEDER (NEC 550.16 / 550.33) =============== |
- | 1. Phase A Hot |
- | 2. Phase B Hot |
- | 3. Neutral (Grounded Conductor) |
- | 4. Equipment Grounding Conductor (Insulated / Bare Copper) |
- | |
- | [INTERIOR DISTRIBUTION PANELBOARD] (Inside Manufactured Home) |
- | - NEUTRAL BUS MUST BE COMPLETELY ISOLATED (FLOATING)! |
- | - NO bonding screw or strap between neutral bus and metal enclosure! |
- | - Equipment Grounding Bus bonded directly to metal enclosure & chassis. |
- +-----------------------------------------------------------------------------+
Why the 4-Wire Isolated Neutral is Critical (NEC 550.16):
If an electrician incorrectly installs a 3-wire feeder or bonds the neutral to the panel enclosure inside a mobile home, return neutral current from 120V appliances splits across the neutral wire AND the metal frame/aluminum siding of the home. Anyone touching the exterior metal siding while standing on the wet ground receives an electrical shock.
4. Recreational Vehicles & RV Parks (NEC Article 551)
NEC Article 551 establishes electrical requirements for RV parks and campground power pedestals. +-----------------------------------------------------------------------------+
- | RV PARK RECEPTACLE DISTRIBUTION (NEC 551.71) |
- | |
- | 1. 20-Ampere, 125-Volt GFCI Outlets (NEMA 5-20R): |
- | - Every RV site with electrical power must have at least one 20A GFCI. |
- | |
- | 2. 30-Ampere, 125-Volt Outlets (NEMA TT-30R): |
- | - At least 70% of all electrical supply sites must have 30A receptacles|
- | |
- | 3. 50-Ampere, 120/240-Volt Outlets (NEMA 14-50R): |
- | - At least 20% of all electrical supply sites must have 50A receptacles|
- | |
- | *Demand Factors (NEC Table 551.73): Feeder demand factors scale down from |
- | 100% for 1-4 sites to 41% for 36+ sites. |
- +-----------------------------------------------------------------------------+
Loading diagram... Agricultural Buildings & Manufactured Homes Compliance Architecture (NEC Articles 547 & 550)