Study guide

13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)

Oklahoma Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety

1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection

2 Chapter 2: General Electrical Theory & Calculations

2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments

3 Chapter 3: General Installation Requirements (NEC Article 110)

3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable

4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)

4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)

5 Chapter 5: Services & Service Equipment (NEC Article 230)

5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)

6 Chapter 6: Electrical Load Calculations (NEC Article 220)

6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)

7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)

7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)

8 Chapter 8: Grounding and Bonding (NEC Article 250)

8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)

9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)

9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)

10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems

10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)

11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)

11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)

12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)

12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)

13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)

13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)

14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems

14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)

13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)

Key Takeaways Explain This Topic AI

Table 515.3 classifies the spaces around bulk storage plant tanks, vents, pumps, loading racks, and pits as Class I, Division 1 or Division 2 by measured distance from the source of the flammable vapor.

NEC 515.8 requires underground wiring at bulk storage plants to be in threaded rigid metal conduit or threaded steel intermediate metal conduit, with PVC, RTRC, or HDPE permitted only under not less than 2 feet of cover.

Where nonmetallic conduit is used underground at a bulk storage plant, threaded RMC or threaded steel IMC must be used for the last 2 feet of the run to emergence, and an equipment grounding conductor must be included for raceway continuity.

Under Table 516.5, the interior of an enclosed spray booth or spray room is a Class I, Division 1 location, and the space within 3 feet of any booth opening is Class I, Division 2.

Article 516 requires that electrical wiring and equipment located above or adjacent to classified spray areas but not within them use rigid metal conduit, intermediate metal conduit, EMT, Type MI cable, or metal boxes and fittings containing no taps, splices, or terminal connections.

Last updated: August 2026

13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)

The Special Occupancies subject area lists eight sub-topics for its 10 scored items, and one of them is "wiring in bulk storage plants, paint, and spray areas." Section 13.2 covered commercial garages (Article 511) and motor fuel dispensing (Article 514). Those are retail fuel articles. Article 515 is the wholesale one, and Article 516 is the finishing-process one.

  • Article Covers Typical facility
  • 511 Commercial repair garages Fleet shop, dealership service bay
  • 514 Motor fuel dispensing facilities Gas station, cardlock fueling island

515 Bulk storage plants Tank farm, terminal, distributor with above- or underground storage and truck/rail loading racks

516 Spray application, dipping, coating, and printing processes using flammable or combustible material Paint booth, powder coating line, dip tank, flexographic press

1. Article 515 — Bulk Storage Plants

A bulk storage plant is a facility where flammable liquids are received by tank vessel, pipeline, tank car, or tank vehicle and are stored or blended in bulk for distribution. The scale is the distinguishing feature: a service station dispenses into vehicles, and a bulk plant fills the trucks that fill the service stations.

Classification (515.3 and Table 515.3)

Table 515.3 does the classification work by listing each physical location and the classified extent around it. The pattern to internalize is that the classified envelope shrinks as the vapor source becomes more enclosed and better ventilated :

Inside a building or enclosure containing flammable liquid transfer — generally Class I, Division 1 in the immediate area of the transfer, with Division 2 extending outward and upward.

Around a vent discharging Class I liquids — a Division 1 sphere immediately at the vent opening, surrounded by a larger Division 2 sphere.

At an outdoor loading or unloading rack — Division 1 within a defined radius of the fill connection, Division 2 beyond it and to a defined height above grade.

Pits, sumps, and below-grade areas in or adjacent to a classified location — classified Division 1 , because heavier-than-air vapor collects there and cannot ventilate.

Aboveground tanks — the shell, ends, and roof, plus a defined envelope around them.

The exam does not usually ask you to recite a distance; it asks you to recognize that a pit inside a Division 2 area is Division 1 , and that a classified area extends horizontally from grade level , which drives the wiring method.

Underground wiring (515.8) — the most-tested rule in the article

  • Condition Permitted wiring method
  • Underground wiring, general Threaded rigid metal conduit or threaded steel intermediate metal conduit

Alternative Type PVC, Type RTRC, or Type HDPE conduit where buried under not less than 2 feet (600 mm) of cover

Where nonmetallic conduit is used Threaded RMC or threaded steel IMC must be used for the last 2 feet of the underground run to emergence or to the point of connection to the aboveground raceway

In every nonmetallic case An equipment grounding conductor must be included to provide electrical continuity of the raceway system and grounding of non-current-carrying metal parts

The reason for the last-2-feet rule is mechanical: the transition point at grade is where a vehicle strike, a shovel, or frost heave will find the raceway, and it is where an unbonded nonmetallic run would otherwise leave the equipment grounding path dependent on a single conductor with no raceway backup.

Sealing, grounding, and equipment

Seals are required per Article 501 wherever a raceway leaves a Division 1 or Division 2 area, and at the boundary of the classified location.

Grounding and bonding must comply with Article 250 Part V and with the requirements for classified locations — the equipment grounding path may not rely on locknut-and-bushing contact alone.

Above the classified area , ordinary wiring methods may be used, but the raceway entering the classified area from above still requires a boundary seal.

Static electricity control — bonding and grounding of tank vehicles and fill piping during transfer — is a fire-code requirement that the electrician installs and the inspector verifies.

2. Article 516 — Spray Application, Dipping, Coating, and Printing Processes

Article 516 applies where flammable or combustible materials are atomized, applied, dipped, or coated , plus the printing processes that use flammable inks and solvents. The hazard is compound: flammable vapor and combustible residue (overspray), which is why the article restricts equipment even outside the classified space.

Classification (Table 516.5)

  • Location Classification
  • Interior of an enclosed spray booth or spray room Class I, Division 1 (or Zone 1/21)
  • Within 3 feet of any spray booth or spray room opening Class I, Division 2 (or Zone 2/22)

Open spraying with no enclosure A larger Division 1 envelope around the spray operation with Division 2 beyond, per the specific entries of Table 516.5

Adjacent areas cut off by partitions with no communicating opening, or otherwise ventilated Unclassified

Two structural points follow. First, the 3-foot envelope measures from the opening, not from the sprayed part — a booth with a 10-foot-wide open face projects a Division 2 zone 3 feet out across that whole face. Second, adequate ventilation is what keeps the surrounding room unclassified ; when the exhaust fan is interlocked out of service, the classification assumptions behind the whole installation fail, which is why 516.10 requires the spray application equipment to be interlocked with the ventilating system.

Wiring inside and outside the classified space

Inside Class I, Division 1 portions: wiring and equipment must comply with Article 501 for Division 1 — threaded rigid metal conduit or threaded steel IMC, explosionproof or purged equipment, and seals.

Inside Class I, Division 2 portions: Article 501 Division 2 methods apply.

Above and adjacent to the classified area but not within it: Article 516 still restricts the wiring. Wiring in those spaces must be in rigid metal conduit, intermediate metal conduit, electrical metallic tubing, or Type MI cable , or in metal boxes or fittings containing no taps, splices, or terminal connections . The reason is overspray residue: a combustible film accumulates on everything above and near a spray area, and an arcing splice inside an ordinary box in that residue is an ignition source even though the vapor concentration there is below classification.

Luminaires used to illuminate a spray area through a panel must be listed for the purpose , separated from the spray area by a fixed, sealed glass panel, and arranged so the lamp can be serviced from outside the classified space.

Portable electric lamps and equipment may not be used in a spray area during spraying operations except where specifically approved and listed for the location.

Electrostatic equipment

Electrostatic spraying and detearing equipment concentrates high voltage in the presence of atomized solvent, so Article 516 imposes additional controls: the high-voltage equipment must be listed for the purpose, all conductive objects in the spray area (including the parts being coated and the conveyor) must be grounded , automatic means must de-energize the high-voltage supply on loss of ventilation or on failure of the conveyor, and safe distances must be maintained between the electrodes and the grounded work.