Study guide
13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514)
Oklahoma Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety
1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection
2 Chapter 2: General Electrical Theory & Calculations
2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments
3 Chapter 3: General Installation Requirements (NEC Article 110)
3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable
4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)
4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)
5 Chapter 5: Services & Service Equipment (NEC Article 230)
5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)
6 Chapter 6: Electrical Load Calculations (NEC Article 220)
6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)
7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)
7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)
8 Chapter 8: Grounding and Bonding (NEC Article 250)
8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)
9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)
9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)
10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems
10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)
11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)
11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)
12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)
12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)
13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)
13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)
14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems
14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)
13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514)
Key Takeaways Explain This Topic AI
Commercial repair garages (NEC Article 511) are classified based on major vs. minor repair; in major repair garages, the space from floor level up to 18 inches (450 mm) is Class I, Division 2 throughout unless positive mechanical ventilation is provided.
Unventilated service and lubrication pits below garage floor level are classified as Class I, Division 1; providing continuous mechanical ventilation of at least 4 air changes/hour or 1 cfm/sq ft with exhaust at the pit floor declassifies the pit to Class I, Division 2.
Under NEC Article 514 and Table 514.3(B)(1), the internal cavity of a fuel dispenser housing and dispenser pit is Class I, Division 1; the outdoor area up to 18 inches above grade within a 20-foot horizontal radius from the dispenser is Class I, Division 2.
NEC 514.9 mandates a conduit seal as the first fitting where raceways enter or emerge from dispenser pits or housings, with no unions, couplings, or fittings permitted between the seal and the dispenser housing.
Emergency disconnects for motor fuel dispensing facilities (NEC 514.11) must simultaneously disconnect power to all conductors including the grounded (neutral) conductor, located between 20 feet and 100 feet from the dispensers.
Last updated: August 2026
Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (NEC Articles 511 & 514)
Facilities that service motor vehicles and dispense volatile hydrocarbon fuels (gasoline, ethanol blends, diesel, CNG, and LNG) are subject to specialized National Electrical Code standards. Gasoline vapors are heavier than air (vapor density of approximately 3.0 to 4.0 compared to air at 1.0), meaning spilled fuel vapors sink to the floor, migrate into depressions and service pits, and create invisible explosive blankets. Articles 511 and 514 establish strict zoning, ventilation, sealing, and emergency disconnect mandates to prevent catastrophic ignition.
1. Commercial Garages: Repair and Storage (NEC Article 511)
NEC Article 511 applies to locations used for service, repair, and storage of self-propelled vehicles (automobiles, buses, trucks, tractors) fueled with flammable liquids or flammable gases.
Major vs. Minor Repair Garages (NEC 511.2 Definitions):
Major Repair Garage: A building or portion of a building where major repairs, engine overhauls, painting, body work involving torch cutting/welding, fuel tank drainage, or fuel system repairs are performed.
Minor Repair Garage: A building used for lubrication, oil changes, tire rotation, brake maintenance, fluid replacement, or minor tune-ups where fuel tanks are NOT opened or drained. +-----------------------------------------------------------------------------+
- | COMMERCIAL REPAIR GARAGE HAZARD ZONES (NEC 511.3) |
- | |
- | [ABOVE 18 INCHES] |
- | - Unclassified space (provided ventilation meets 511.3(C)). |
- | - Receptacles & luminaires must be enclosed/gasketed if subject to sparks.|
- | - Luminaires below 12 ft must be totally enclosed or shielded. |
- | |
- | [FLOOR LEVEL UP TO 18 INCHES (450 mm)] ================================== |
- | - CLASSIFIED AS CLASS I, DIVISION 2 throughout entire room. |
- | - Wiring must be RMC, IMC, EMT, or listed cable (501.10(B)). |
- | - Receptacles must be explosionproof OR mounted > 18 in. above floor. |
- | |
- | [SERVICE / LUBRICATION PITS (BELOW FLOOR LEVEL)] |
- | - WITHOUT Positive Ventilation: CLASS I, DIVISION 1 (Floor to rim). |
- | - WITH Positive Mechanical Ventilation (4 ACH or 1 cfm/sq ft with |
- | exhaust at pit bottom): Downgraded to CLASS I, DIVISION 2. |
- +-----------------------------------------------------------------------------+
Garage Ventilation Requirements (NEC 511.3(C) & (D)):
To maintain the space above 18 inches as unclassified, the garage must have continuous mechanical ventilation providing at least 4 air changes per hour (ACH) or 1.0 cubic foot per minute per square foot (cfm/sq ft) of floor area.
Exhaust air must be drawn from intake points located not more than 12 inches (300 mm) above the finished floor line to capture heavy settling gasoline vapors.
Where mechanical ventilation fails, interlocks must de-energize non-classified electrical equipment or trigger emergency ventilation alarms.
2. Motor Fuel Dispensing Facilities (NEC Article 514)
NEC Article 514 regulates retail service stations, commercial fleet refueling plazas, and marine/aviation fuel dispensing facilities.
Hazardous Classification Boundaries (NEC Table 514.3(B)(1))
Table 514.3(B)(1) provides precise geometric envelopes classifying spaces around fuel dispensers based on the proximity to volatile gasoline and ethanol liquid/vapor sources: +-----------------------------------------------------------------------------+
- | FUEL DISPENSER CLASSIFICATION ENVELOPE |
- | |
- | Dispenser Housing |
- | +---------------------+ |
- | | | |
- | | Class I, Div 1 | |
- | | (Entire Interior | <-- Class I, Div 2 |
- | | Cavity up to 4ft) | Within 18" of |
- | +----------+----------+ dispenser housing |
- | | |
- | [GRADE LEVEL] | |
- | ==============+====================+====================+============== |
- | 18" Height | | 18" Height |
- | <-----------> | <------- CLASS I, DIVISION 2 ---------> | <-----------> |
- | <------------------ 20 FEET HORIZONTAL RADIUS --------->| |
- | |
- | [DISPENSER CONTAINMENT PIT] |
- | - Entire pit below island is CLASS I, DIVISION 1. |
- +-----------------------------------------------------------------------------+
Summary Table of Fuel Dispenser Hazard Classifications:
Location / Boundary Zone NEC Classification Extent of Classified Space
Dispenser Cavity / Housing Class I, Division 1 Entire interior cavity of dispenser from base up to 4.0 feet (1.2 m), and entire containment pit below dispenser.
Dispenser Exterior Envelope Class I, Division 2 Horizontally within 18 inches (450 mm) of the dispenser housing, extending from island base up to 4.0 feet (1.2 m).
Outdoor Ground Perimeter Class I, Division 2 From grade level up to 18 inches (450 mm) high, extending horizontally 20 feet (6.0 m) in all directions from the dispenser island perimeter.
Overhead Dispenser Units Class I, Division 1 & 2 Div 1 inside internal housing; Div 2 within 18 inches of housing down to ground level.
Underground Fuel Tank Fill Pipe Class I, Division 1 Within 3.0 feet (900 mm) of fill connection opening in all directions.
Underground Fuel Tank Fill Pipe Class I, Division 2 Between 3.0 feet and 10.0 feet horizontally from fill connection, from grade up to 18 inches high.
3. Conduit Sealing Requirements for Fuel Dispensers (NEC 514.9)
Because fuel dispensers sit directly atop underground tanks and delivery pipes, raceways connecting to dispensers represent direct pathways for gasoline liquid and vapors to enter electrical systems. +-----------------------------------------------------------------------------+
- | DISPENSER CONDUIT SEAL MANDATES (NEC 514.9) |
- | |
- | [ Inside Dispenser Housing ] |
- | | |
- | +-----------------------------+ |
- | | CONDUIT SEAL FITTING (EYS) | |
- | +-----------------------------+ |
- | | |
- | =================================+===================================== |
- | CONCRETE ISLAND / SLAB | (First fitting emerging from slab!) |
- | | |
- | *CRITICAL CODE RULES (NEC 514.9(A)): |
- | 1. The conduit seal MUST be the FIRST fitting where the raceway emerges |
- | into the dispenser housing or dispenser containment pit. |
- | 2. NO UNIONS, COUPLINGS, BOXES, OR FITTINGS are permitted between the |
- | seal fitting and the point of emergence from the slab/ground! |
- | 3. Boundary seals are required where raceways exit the 20-foot Class I, |
- | Division 2 perimeter into unclassified territory. |
- +-----------------------------------------------------------------------------+
- 4. Emergency Disconnecting Means (NEC 514.11)
In the event of a drive-off hose rupture, fuel spill, vehicle collision, or forecourt fire, all electrical power to dispensing pumps and controls must be instantaneously dropped from a safe location. +-----------------------------------------------------------------------------+
- | EMERGENCY DISCONNECT REQUIREMENTS (NEC 514.11) |
- | |
- | 1. SIMULTANEOUS ALL-CONDUCTOR DISCONNECTION (NEC 514.11(A)): |
- | - Must simultaneously disconnect ALL conductors of all circuits |
- | supplying or passing through any dispenser, submersible turbine pump |
- | (STP), solenoid valve, vapor recovery system, and data wiring. |
- | - MANDATORY: The GROUNDED (NEUTRAL) CONDUCTOR MUST BE DISCONNECTED! |
- | (Only the Equipment Grounding Conductor remains connected). |
- | |
- | 2. LOCATION AND DISTANCE RULES (NEC 514.11(B)): |
- | - Minimum Distance: Not less than 20 FEET (6.0 m) from dispensers. |
- | - Maximum Distance: Not more than 100 FEET (30.0 m) from dispensers. |
- | - Must be readily accessible and clearly identified with a permanent |
- | sign reading "EMERGENCY FUEL SHUTOFF" or similar wording. |
- | |
- | 3. RESETTING MECHANISM: |
- | - Disconnect must be designed such that it can be reset ONLY manually |
- | by authorized attendants/technicians. |
- +-----------------------------------------------------------------------------+
Why Disconnect the Neutral Conductor?
In multi-transformer commercial distribution systems, neutral conductors carry return currents and may have a small potential to earth (stray neutral voltage). If a neutral wire remains connected during an emergency shutoff and a metal conduit is severed in a car collision, neutral current can arc to ground, creating an ignition spark in a puddle of spilled gasoline. Disconnecting the neutral completely eliminates this stray current ignition source.