Study guide
3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28)
Oklahoma Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety
1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection
2 Chapter 2: General Electrical Theory & Calculations
2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments
3 Chapter 3: General Installation Requirements (NEC Article 110)
3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable
4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)
4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)
5 Chapter 5: Services & Service Equipment (NEC Article 230)
5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)
6 Chapter 6: Electrical Load Calculations (NEC Article 220)
6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)
7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)
7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)
8 Chapter 8: Grounding and Bonding (NEC Article 250)
8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)
9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)
9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)
10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems
10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)
11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)
11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)
12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)
12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)
13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)
13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)
14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems
14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)
3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28)
Key Takeaways Explain This Topic AI
NEC Table 110.28 establishes environmental ratings for enclosures: Type 1 (indoor dry), Type 3R (outdoor rainproof and ice-resistant), Type 4/4X (watertight, dust-tight, corrosion-resistant), and Type 12 (industrial dust and oil drip-tight).
Service equipment in other than dwelling units must be field marked under NEC 110.24 with maximum available fault current (AFC) and calculation date, updated whenever system modifications alter AFC (110.24(B)).
NEC 110.9 mandates that protective devices have an Ampere Interrupting Capacity (AIC) sufficient for the maximum available fault current at their line terminals; exceeding AIC leads to catastrophic arc flash and explosion.
NEC 110.10 requires complete component protection, ensuring that short-circuit current ratings (SCCR) of panels, contactors, and busways coordinate with overcurrent devices to clear faults without extensive damage.
Disconnecting means and panelboard circuits must be legibly and durably identified with specific circuit directories under NEC 110.22, and series-rated combinations must carry prominent warning labels.
Last updated: August 2026
Enclosure Types, Markings & Available Fault Current (NEC 110.24 & 110.28)
Selecting the correct enclosure protects electrical components from environmental contamination, moisture, and chemical deterioration. Simultaneously, verifying that equipment can safely withstand and interrupt available short-circuit currents is fundamental to preventing catastrophic arc blast explosions. On the Oklahoma Journeyman Electrician examination, Article 110 questions frequently test your knowledge of NEMA/NEC enclosure types (Table 110.28) , Available Fault Current field markings (110.24) , Interrupting Ratings (110.9) , and Circuit Directories (110.22) .
1. Enclosure Selection and Environmental Types (NEC Table 110.28)
NEC Table 110.28 provides the definitive criteria for selecting electrical enclosures based on environmental exposure. Enclosures are not interchangeable; installing an indoor enclosure outdoors or a standard enclosure in a washdown area creates severe shock, fire, and equipment degradation risks. +-----------------------------------------------------------------------------+
- | NEC TABLE 110.28 ENCLOSURE TYPE MATRIX |
- | |
- | [INDOOR ENCLOSURES] |
- | - Type 1: General purpose indoor; protects against falling dirt. |
- | - Type 2: Indoor drip-proof; protects against light falling liquids. |
- | - Type 12 / 12K: Industrial dust-tight & drip-tight; resists oil, |
- | coolant seepage, lint, fibers, and flying particles. |
- | |
- | [OUTDOOR ENCLOSURES] |
- | - Type 3R: Rainproof, sleet-resistant, ice-damage resistant. Standard |
- | for outdoor panels, air conditioning disconnects, and meter sockets. |
- | - Type 3S: Weatherproof; operable when external mechanisms are ice-laden. |
- | - Type 4: Watertight and dust-tight; protects against hose-directed water.|
- | - Type 4X: Watertight, dust-tight, PLUS superior CORROSION RESISTANCE |
- | (stainless steel, fiberglass, or polycarbonate). Used in chemical |
- | plants, wastewater treatment, coastal marine environments. |
- | - Type 6P: Submersible under water or oil for prolonged periods. |
- +-----------------------------------------------------------------------------+
Enclosure Selection Guide:
- Enclosure Type Location Environmental Protection Factors
- Type 1 Indoor Falling dirt, accidental contact
- Type 3R Outdoor Falling rain, sleet, snow, external ice formation (drain hole provided)
- Type 4 Indoor/Outdoor Windblown dust/rain, splashing water, hose-directed washdown
- Type 4X Indoor/Outdoor Type 4 protections plus severe corrosive agents (chemical/saltwater)
- Type 12 Indoor Circulating dust, falling dirt, dripping non-corrosive liquids, machine oils
- 2. Available Fault Current Field Marking (NEC 110.24)
When a short circuit occurs, the amount of current that flows is limited only by the impedance of the utility transformer, service conductors, and upstream grid. Service equipment must be labeled so electricians and inspectors can verify that circuit breakers and fuses have sufficient interrupting capacity. +-----------------------------------------------------------------------------+
- | FIELD MARKING OF AVAILABLE FAULT CURRENT (NEC 110.24) |
- | |
- | [MANDATORY FIELD LABEL ON SERVICE EQUIPMENT] |
- | (Other than dwelling units - Commercial, Industrial, Multi-Family) |
- | |
- | +---------------------------------------------------------------------+ |
- | | MAXIMUM AVAILABLE FAULT CURRENT: 42,850 RMS AMPS SYMMETRICAL | |
- | | DATE FAULT CURRENT CALCULATED: AUGUST 18, 2026 | |
- | +---------------------------------------------------------------------+ |
- | |
- | - Must be legible, permanent, and withstand environmental conditions. |
- | - System Modifications (110.24(B)): If the utility changes the |
- | transformer or service conductors, the AFC must be RECALCULATED and |
- | the label updated immediately. |
- | - Exception: Industrial installations with qualified engineering staff. |
- +-----------------------------------------------------------------------------+
- 3. Interrupting Rating (110.9) vs. Short-Circuit Current Rating (SCCR, 110.10)
Understanding the distinction between AIC and SCCR is critical for journeyman code competence.
Interrupting Rating (NEC 110.9):
Applies to overcurrent protective devices (fuses and circuit breakers).
The maximum RMS symmetrical current that the device is rated to safely interrupt at its nominal voltage without blowing apart or creating an sustained arc.
Standard residential breakers are rated 10,000 Amperes Interrupting Capacity (10 kAIC) , while commercial/industrial breakers often require 22 kAIC, 42 kAIC, 65 kAIC, or 100 kAIC .
If a fault occurs with 35,000A available at a 10 kAIC breaker, the breaker will catastrophically explode before opening the circuit.
Short-Circuit Current Rating (SCCR, NEC 110.10):
Applies to complete electrical equipment assemblies (industrial control panels, switchboards, meter disconnects, motor starters, busway assemblies).
The maximum prospective fault current that an assembly can withstand without catching fire or suffering structural busbar failure during the time it takes an upstream protective device to clear the fault.
Series-Rated Combinations (NEC 110.22(B) & (C)):
When a higher-rated upstream main breaker/fuse protects lower-rated downstream branch circuit breakers tested and listed together by an NRTL (e.g., a 22 kAIC main protecting 10 kAIC branch breakers at a 20 kA fault location).
Mandatory Warning Label: The enclosure must be field marked with a conspicuous label stating: "CAUTION — SERIES RATED SYSTEM — XXXX IDENTIFIED REPLACEMENT COMPONENTS ONLY" .
4. Identification of Disconnecting Means & Circuits (NEC 110.22)
Every disconnecting means (circuit breakers, safety switches, motor disconnects) must be legibly and durably marked to indicate its purpose unless located and arranged so the purpose is evident.
Requirements for Circuit Directories:
Panelboard circuit directories must be specific, clear, and unambiguous .
Descriptions such as "Lights", "Plugs", or "Spare" (for an active breaker) are non-compliant.
Compliant directory labels must state precise functional locations, such as "Receptacles - East Office Room 102" or "HVAC Rooftop Unit #3" .
Labels must withstand environmental degradation (fading, moisture, dirt).