Study guide
3.1 Examination, Identification, Installation & Use of Equipment (110.3)
Oklahoma Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety
1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection
2 Chapter 2: General Electrical Theory & Calculations
2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments
3 Chapter 3: General Installation Requirements (NEC Article 110)
3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable
4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)
4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)
5 Chapter 5: Services & Service Equipment (NEC Article 230)
5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)
6 Chapter 6: Electrical Load Calculations (NEC Article 220)
6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)
7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)
7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)
8 Chapter 8: Grounding and Bonding (NEC Article 250)
8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)
9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)
9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)
10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems
10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)
11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)
11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)
12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)
12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)
13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)
13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)
14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems
14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)
3.1 Examination, Identification, Installation & Use of Equipment (110.3)
Key Takeaways Explain This Topic AI
NEC 110.3(A) mandates eight core examination factors when evaluating electrical equipment, including suitability for the environment, mechanical strength, wire-bending space, and electrical insulation.
NEC 110.3(B) makes manufacturer installation instructions and listing/labeling requirements by a Nationally Recognized Testing Laboratory (NRTL such as UL, ETL, CSA) legally binding.
Under NEC 110.12, all electrical equipment must be installed in a neat and workmanlike manner, with unused enclosure openings effectively closed (110.12(A)) and internal parts protected against construction debris, paint, and contaminants (110.12(B)).
NEC 110.11 prohibits installing standard equipment where exposed to deteriorating agents such as dampness, corrosive fumes, or excessive temperatures unless identified for that specific environment.
NEC 110.13 mandates secure mechanical fastening of equipment, strictly prohibits wooden plugs driven into masonry or concrete, and requires unobstructed natural ventilation and cooling.
Last updated: August 2026
Examination, Identification, Installation & Use of Equipment (NEC 110.3)
Article 110 of the National Electrical Code (NEC) serves as the universal foundation for all electrical installations. Before calculating feeder sizes, running raceways, or setting overcurrent devices, every journeyman electrician must understand the general requirements governing equipment approval, environmental suitability, mounting integrity, and quality of workmanship. On the Oklahoma Journeyman Electrician examination, questions drawn from Article 110 test your ability to evaluate equipment listings, interpret manufacturer instructions, and identify code-compliant mechanical installations.
1. Examination of Equipment (NEC 110.3(A))
Before electrical equipment is installed, the Authority Having Jurisdiction (AHJ) and the installing electrician must evaluate its suitability, safety, and physical condition. NEC 110.3(A) establishes eight specific examination factors that must be judged:
Suitability for Installation and Use: Equipment must be verified for suitability in conformity with the NEC. Suitability is primarily evidenced by listing or labeling from a qualified third-party testing laboratory.
Mechanical Strength and Durability: Enclosures, parts, and mountings must provide structural adequacy to withstand normal mechanical stress, including the adequacy of parts designed to enclose and protect other equipment.
Wire-Bending and Connection Space: Equipment enclosures must provide adequate physical volume and gutter space so conductors can enter, bend, and terminate without damaging insulation or stressing terminal lugs.
Electrical Insulation: Insulation properties must be adequate for the voltage, dielectric stresses, and operating temperatures encountered.
Heating Effects Under Normal and Abnormal Conditions: Equipment must dissipate heat safely without exceeding component temperature ratings or creating a fire hazard to adjacent combustible construction.
Arcing Effects: Arcing parts (such as open switches, contactors, or circuit breaker vents) must be enclosed or isolated so that hot gases and sparks cannot ignite nearby materials or injure personnel.
Classification by Type, Size, Voltage, Current Capacity, and Specific Use: Equipment must match the exact electrical parameters of the system (voltage rating, phase configuration, continuous current rating, and frequency).
Other Factors Contributing to Practical Safeguarding: Any additional factors affecting the safety of persons using or likely to come into contact with the equipment.
2. Mandatory Compliance with Listing and Labeling (NEC 110.3(B))
One of the most frequently cited and critical rules in the entire NEC is NEC 110.3(B) :
"Equipment that is listed, labeled, or both shall be installed and used in accordance with any instructions included in the listing or labeling." +-----------------------------------------------------------------------------+
- | NEC 110.3(B) LISTING & LABELING CHAIN |
- | |
- | [OSHA Recognized NRTL] --> [Tests Equipment to ANSI/UL Standards] |
- | (UL, Intertek/ETL, CSA) - Establishes maximum voltage & current |
- | - Defines mounting orientations |
- | - Specifies terminal conductor types/ranges |
- | |
- | | |
- | v |
- | [Manufacturer Instructions] --> [Legally Binding Code Mandate] |
- | - Lug torque values - Installing contrary to instructions |
- | - Terminal temperature limits violates NEC 110.3(B) |
- | - Enclosure mounting clearances - Field alterations void the listing |
- +-----------------------------------------------------------------------------+
Practical Applications of NEC 110.3(B) for Journeymen:
Nationally Recognized Testing Laboratories (NRTLs): In the United States, independent testing laboratories such as Underwriters Laboratories (UL), Intertek (ETL), and CSA Group test equipment against rigorous safety standards. When an NRTL lists a product, its installation instructions become an enforceable extension of the NEC.
Field Modifications: Modifying an enclosure (e.g., cutting unauthorized ventilation slots, drilling oversized holes in unapproved locations, or replacing factory lugs with unlisted aftermarket parts) voids the listing and violates NEC 110.3(B) unless specifically permitted by the manufacturer's written instructions.
Multi-Conductor Terminations: Inserting two wires under a terminal screw designed and listed for a single wire is an explicit violation of 110.3(B) and 110.14(A).
Breaker Interchangeability: Installing a circuit breaker brand into a panelboard for which it is not listed (classified) violates 110.3(B), even if the breaker physically snaps into the busbar.
3. Mechanical Execution of Work (NEC 110.12)
NEC 110.12 mandates that electrical equipment shall be installed in a neat and workmanlike manner . While this standard was historically considered subjective, the NEC and industry standards (such as NECA 1, Standard Practice for Good Workmanship in Electrical Construction ) codify specific enforceable criteria.
Unused Openings (NEC 110.12(A))
Unused cable or conduit knockouts, cutout openings, and hub entries in boxes, panelboards, meter centers, and switchboards must be effectively closed to afford protection substantially equivalent to the wall of the enclosure.
Where metallic plugs or plates are used with nonmetallic enclosures, they must be recessed at least 6 mm (1/4 in.) from the outer surface to avoid conductive bridging.
Open knockout holes in live panelboards create severe fire, arc flash, and rodent intrusion hazards.
Integrity of Electrical Equipment and Contamination (NEC 110.12(B))
Internal parts of electrical equipment, including busbars, wiring gutters, terminal lugs, switches, and insulation, must not be damaged or contaminated by foreign materials.
Prohibited contaminants include paint, plaster, drywall compound, cleaner solvents, abrasive dust, corrosive vapors, or water .
Equipment exposed during construction must be shielded and protected. If equipment is damaged by water submersion or plaster encasement, the AHJ can require complete equipment replacement per NEMA guidelines.
4. Deteriorating Agents & Environmental Exposure (NEC 110.11)
Electrical equipment must be designed and selected specifically for the environmental conditions of the installation site. NEC 110.11 establishes that unless identified for use in the operating environment, no conductors or equipment shall be located in:
Damp or Wet Locations: Locations subject to moisture, water run-off, condensation, or direct weather.
Corrosive Atmospheres: Areas exposed to gases, fumes, vapors, liquids, or chemicals having a deteriorating effect on conductors or equipment (e.g., chemical storage rooms, fertilizer processing facilities, chlorine storage areas in water treatment or swimming pool pump rooms).
Excessive Temperatures: Locations where ambient operating temperatures exceed standard equipment ratings (typically 40°C / 104°F unless marked otherwise).
- Environment Category Deteriorating Factors Present Mandatory Equipment Classification
- Dry Location Standard atmospheric conditions, no moisture Type 1 Enclosures, standard steel fittings
- Damp Location Protected from weather but moderate moisture Type 3R, Type 12, or weatherproof fittings
- Wet Location Underground, direct rain, car wash bays Type 4, Type 4X, listed wet-location raceways
- Corrosive Location Chlorine, ammonia, sulfuric acid, salts Type 4X (Stainless Steel/Nonmetallic), PVC conduit
- 5. Mounting and Cooling of Equipment (NEC 110.13)
Proper mechanical support and thermal management ensure electrical equipment operates safely throughout its service life without overheating or detaching under mechanical and magnetic stresses. +-----------------------------------------------------------------------------+
- | MOUNTING & COOLING RULES (NEC 110.13) |
- | |
- | [NEC 110.13(A): MOUNTING] [NEC 110.13(B): COOLING] |
- | - Firmly secured to surface - Unobstructed natural airflow |
- | - Wooden plugs in masonry PROHIBITED - No blocked ventilation louvers |
- | - Approved masonry anchors, toggle - Maintain manufacturer minimum |
- | bolts, expansion anchors mandatory side and top clearances |
- +-----------------------------------------------------------------------------+
- Mounting Integrity (NEC 110.13(A))
Electrical equipment must be firmly secured to the surface on which it is mounted.
Prohibition on Wooden Plugs: Wooden plugs driven into holes in masonry, concrete, brick, plaster, or similar materials shall not be used for securing electrical equipment or raceway supports. Wood shrinks, rots, and loses holding power over time. Installers must use approved mechanical expansion anchors, epoxy anchors, or masonry screws (such as Tapcons).
Cooling and Airflow Clearance (NEC 110.13(B))
Electrical equipment that depends on natural circulation of air or convection for cooling must be installed so that room airflow over its surfaces is not obstructed by walls, adjacent equipment, or structural framing.
Ventilation openings and louvers on transformers, variable frequency drives (VFDs), and panelboards must be kept clear of storage, insulation, and building materials.