Study guide

11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)

Oklahoma Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety

1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection

2 Chapter 2: General Electrical Theory & Calculations

2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments

3 Chapter 3: General Installation Requirements (NEC Article 110)

3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable

4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)

4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)

5 Chapter 5: Services & Service Equipment (NEC Article 230)

5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)

6 Chapter 6: Electrical Load Calculations (NEC Article 220)

6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)

7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)

7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)

8 Chapter 8: Grounding and Bonding (NEC Article 250)

8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)

9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)

9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)

10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems

10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)

11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)

11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)

12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)

12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)

13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)

13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)

14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems

14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)

11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)

Key Takeaways Explain This Topic AI

Air-conditioning and refrigeration equipment containing hermetic refrigerant motor-compressors are governed specifically by NEC Article 440, superseding general Article 430 rules due to suction gas cooling.

Under NEC 440.4(C), if the equipment nameplate lists a Branch-Circuit Selection Current (BCSC) greater than marked rated-load current, BCSC must be used for conductor, disconnect, and OCPD sizing.

Minimum Circuit Ampacity (MCA; NEC 440.32, 440.35) represents 125% of compressor rated current plus 100% of concurrent auxiliary loads; field branch conductors must have allowable ampacity ≥ MCA.

Maximum Overcurrent Protective Device (MOCP; NEC 440.22) is sized at not more than 175% of compressor rated current (max 225% exception); field circuit breakers or fuses must not exceed nameplate MOCP.

NEC 440.14 mandates that the equipment disconnecting means must be located 'within sight from' (visible and ≤50 ft), readily accessible, and NOT mounted on panels designed to be removed for servicing.

Last updated: August 2026

Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)

Air conditioning, heat pump, and commercial refrigeration systems operate with hermetic refrigerant motor-compressors —specialized assemblies where the electric motor and compressor pump are completely sealed within a welded steel or cast-iron shell exposed directly to refrigerant and lubricating oil. Because the motor windings are continuously cooled by cold suction gas returning from the evaporator, a hermetic motor can carry significantly higher electrical loads without overheating than a conventional open-air motor of the same physical dimensions. Consequently, the National Electrical Code dedicates Article 440 specifically to hermetic equipment, superseding standard Article 430 requirements.

1. Article 440 Scope & Nameplate Terminology (NEC 440.4)

On the Oklahoma Journeyman Electrician examination, electricians are not required to calculate internal compressor physics from scratch. Instead, manufacturers perform listed laboratory calculations under UL 1995 / UL 60335-2-40 and stamp the exact field requirements onto the equipment nameplate. Understanding how the NEC interprets these nameplate values is essential: +-----------------------------------------------------------------------------+

  • | ANATOMY OF AN HVAC EQUIPMENT NAMEPLATE |
  • | |
  • | MODEL: AC-4800-X VOLTS: 208/230V 1-PHASE 60 HZ |
  • | COMPRESSOR RLC: 24.2 A LOCKED ROTOR (LRA): 144.0 A |
  • | OUTDOOR FAN MOTOR FLA: 2.1 A 1/4 HP 1100 RPM |
  • | ----------------------------------------------------------------------- |
  • | MINIMUM CIRCUIT AMPACITY (MCA): 32.4 AMPERES |
  • | MAX OVERCURRENT PROTECTIVE DEVICE: 50 AMPERES |
  • | MAX FUSE OR HACR CIRCUIT BREAKER |
  • +-----------------------------------------------------------------------------+

Key Terms and Definitions:

Rated-Load Current (RLC): The current drawn by the compressor under maximum rated operating conditions (temperature, head pressure, suction pressure).

Branch-Circuit Selection Current (BCSC; NEC 440.4(C)): A current value marked on the nameplate that is greater than the rated-load current, used where the compressor is designed for sustained peak loading. Where marked, BCSC must be used in place of RLC for all calculations.

Locked-Rotor Amperes (LRA): The instantaneous current drawn when the compressor rotor is mechanically stalled at startup (typically 5 to 7 times running current). Used to determine disconnect interrupting capacity and horsepower ratings.

2. Minimum Circuit Ampacity (MCA) & Conductor Sizing (NEC 440.32–440.35)

The Minimum Circuit Ampacity (MCA) stamped on the equipment nameplate dictates the smallest allowable conductor ampacity that can be installed in the field: Conductor Allowable Ampacity ≥ Nameplate MCA \text{Conductor Allowable Ampacity} \ge \text{Nameplate MCA} Conductor Allowable Ampacity ≥ Nameplate MCA +-----------------------------------------------------------------------------+

  • | HOW THE MANUFACTURER CALCULATES MCA |
  • | |
  • | MCA = (1.25 x Compressor RLC/BCSC) + Sum(All Concurrent Fan/Pump Motors) |
  • | |
  • | FROM NAMEPLATE EXAMPLE: |
  • | MCA = (1.25 x 24.2 A) + 2.1 A = 30.25 A + 2.1 A = 32.35 A -> 32.4 Amps |
  • +-----------------------------------------------------------------------------+

Field Conductor Sizing Rules:

Select from NEC Table 310.16: Match the conductor's 75°C ampacity rating directly to the MCA value. For an MCA of 32.4A, select #8 AWG Copper (rated 50A at 75°C) or #8 AWG Aluminum (rated 40A at 75°C). (Note: #10 AWG Cu has a 75°C rating of 35A, which also satisfies 32.4A where termination temperatures permit).

Small Conductor Rule Exemption (NEC 240.4(G)): Article 440 exempts HVAC equipment from the general 15A, 20A, and 30A caps of NEC 240.4(D). If an MCA is 18.0A and the MOCP is 30A, #12 AWG Copper (rated 20A/25A) is 100% code-compliant on a 30A breaker!

3. Maximum Overcurrent Protective Device (MOCP) & HACR Breakers (NEC 440.22)

The Maximum Overcurrent Protective Device (MOCP) represents the largest fuse or circuit breaker permitted to protect the branch circuit: +-----------------------------------------------------------------------------+

  • | HOW THE MANUFACTURER CALCULATES MOCP |
  • | |
  • | STANDARD SIZING (NEC 440.22(A)): |
  • | MOCP = (1.75 x Compressor RLC) + Sum(Other Motors) |
  • | Rounded DOWN to the next standard rating (or up under specific test rules)|
  • | |
  • | ABSOLUTE MAXIMUM EXCEPTION (NEC 440.22(A) Exception 1): |
  • | If 175% cannot start unit, maximum is increased to 225% of RLC. |
  • +-----------------------------------------------------------------------------+
  • Critical Nameplate Markings & HACR Mandates (NEC 110.3(B) & 440.4(B))

Electricians must inspect the exact phrasing of the overcurrent protective device marking:

"MAX FUSE SIZE: 50A": The branch circuit MUST be protected by fuses (such as a fused disconnect or fuse panel). Installing an inverse-time circuit breaker is a direct violation of NEC 110.3(B) (listing requirements).

"MAX FUSE OR HACR BREAKER: 50A" (or "MAX CKT BKR: 50A"): The branch circuit is permitted to be protected by either fuses or an inverse-time circuit breaker listed for Heating, Air Conditioning, and Refrigeration (HACR) duty. Today, virtually all standard molded-case circuit breakers manufactured by major brands are UL-listed as HACR rated.

4. Disconnecting Means Requirements (NEC 440.14 & 440.12)

NEC 440.14 establishes stringent physical location requirements for air conditioning and refrigeration disconnect switches: +-----------------------------------------------------------------------------+

  • | NEC 440.14 HVAC DISCONNECT RULES |
  • | |
  • | 1. LOCATION: Must be located WITHIN SIGHT FROM the equipment. |
  • | - Visible AND not more than 50 feet (15 m) away. |
  • | |
  • | 2. ACCESSIBILITY: Must be READILY ACCESSIBLE (Article 100). |
  • | - No portable ladders, no crawling, no removing obstacles. |
  • | |
  • | 3. MOUNTING PROHIBITION: The disconnect SHALL NOT be mounted on or |
  • | within panels designed to be removed for servicing the equipment. |
  • | - Screwing a disconnect box into the compressor access door is a |
  • | DANGEROUS CODE VIOLATION! |
  • | |
  • | 4. WORKING CLEARANCE (NEC 110.26): |
  • | - Must maintain 3 feet minimum depth, 30 inches width, and 6.5 ft |
  • | headroom in front of the disconnect switch. |
  • +-----------------------------------------------------------------------------+
  • Disconnect Sizing (NEC 440.12)

Ampere Rating (440.12(A)(1)): Disconnect ampere rating must be at least 115% of the nameplate rated-load current (RLC) or branch-circuit selection current (BCSC).

Horsepower Rating (440.12(A)(2)): Horsepower rating is determined by taking the compressor locked-rotor amperes (LRA) and converting it to horsepower using NEC Table 430.251(A) (1-phase) or Table 430.251(B) (3-phase). +-----------------------------------------------------------------------------+

  • | HVAC BRANCH CIRCUIT SIZING SUMMARY MATRIX |
  • | |
  • | COMPONENT CODE SECTION SELECTION CRITERIA |
  • | ----------------------------------------------------------------------- |
  • | Conductor Size NEC 440.32 / 310.16 Ampacity >= Nameplate MCA |
  • | Overcurrent Device NEC 440.22 / 240.6 Rating <= Nameplate MOCP |
  • | Disconnect Amp Rating NEC 440.12(A)(1) Rating >= 115% of RLC / BCSC |
  • | Disconnect Location NEC 440.14 Within Sight (<= 50 ft) |
  • +-----------------------------------------------------------------------------+

Loading diagram... HVAC Branch Circuit Sizing & Nameplate Decoupling Flowchart (NEC Article 440)