Study guide

7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)

Oklahoma Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety

1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection

2 Chapter 2: General Electrical Theory & Calculations

2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments

3 Chapter 3: General Installation Requirements (NEC Article 110)

3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable

4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)

4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)

5 Chapter 5: Services & Service Equipment (NEC Article 230)

5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)

6 Chapter 6: Electrical Load Calculations (NEC Article 220)

6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)

7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)

7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)

8 Chapter 8: Grounding and Bonding (NEC Article 250)

8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)

9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)

9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)

10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems

10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)

11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)

11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)

12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)

12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)

13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)

13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)

14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems

14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)

7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)

Key Takeaways Explain This Topic AI

Ground-Fault Protection of Equipment (GFPE, NEC 240.13 & 230.95) is mandatory for solidly grounded wye systems >150V to ground (e.g., 480Y/277V) rated 1,000A or higher, capped at 1,200A max pickup and 1.0-second delay for faults ≥ 3,000A.

GFPE is designed to prevent destructive equipment burn-down from low-level arcing ground faults; it does NOT provide personnel shock protection (contrast with Class A GFCI 4–6 mA thresholds).

Selective Coordination (defined in NEC Article 100) requires total isolation of an overcurrent condition strictly to the affected circuit across the full range of overcurrents and operating times; the over-1000-volt overcurrent rules formerly at 240.100 and 240.101 moved to the new Article 245 in the 2023 edition.

Mandatory selective coordination applies to Emergency Systems (NEC 700.32), Legally Required Standby Systems (NEC 701.27), COPS (Article 708), and Health Care Essential Systems (NEC 517.31(G)).

Series-rated systems (NEC 240.86) allow lower-AIC downstream breakers when protected by tested upstream devices, but are prohibited where connected motor full-load currents exceed 1% of the downstream breaker's AIC.

Last updated: August 2026

Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)

In modern commercial and industrial electrical distribution, preventing catastrophic equipment destruction and preserving life-safety power continuity require engineering methodologies beyond simple overcurrent protection. Two critical advanced concepts tested heavily on the Oklahoma Journeyman Electrician exam are Ground-Fault Protection of Equipment (GFPE) and Selective Coordination .

1. Ground-Fault Protection of Equipment (GFPE) (NEC 240.13 & 230.95)

Arguably the most destructive type of electrical event in commercial facilities is an arcing ground fault on a 480Y/277V system. Because 277V to ground can easily sustain an electric arc in air, hundreds or thousands of amperes of arcing fault current can vaporize switchgear buses and enclosures within fractions of a second without drawing sufficient current to instantly trip a standard 1200A, 2000A, or 3000A main overcurrent device. +-----------------------------------------------------------------------------+

  • | THE THREE-PART TRIGGER FOR MANDATORY GFPE |
  • | |
  • | Under NEC 240.13 (Feeders) and NEC 230.95 (Services), GFPE is MANDATORY |
  • | if ALL THREE conditions exist: |
  • | |
  • | 1. SOLIDLY GROUNDED WYE SYSTEM |
  • | (Must have grounded neutral; Delta & ungrounded systems are EXEMPT) |
  • | |
  • | 2. VOLTAGE > 150V TO GROUND & <= 1000V PHASE-TO-PHASE |
  • | - 480Y/277V Systems: MANDATORY (277V to ground > 150V) |
  • | - 208Y/120V Systems: EXEMPT (120V to ground <= 150V) |
  • | - 480V 3-Phase Delta: EXEMPT (Not a solidly grounded Wye) |
  • | |
  • | 3. DISCONNECT RATING OF 1000 AMPERES OR HIGHER |
  • | - Feeder / Main Breaker rated 1000A, 1200A, 1600A, 2000A, etc. |
  • | - Breakers rated 800A or less: EXEMPT |
  • +-----------------------------------------------------------------------------+
  • GFPE Operational Settings & Parameters (NEC 230.95(A))

Maximum Pickup Setting: The ground-fault protection system shall have a maximum setting of 1200 Amperes .

Maximum Time Delay: The maximum time delay shall be 1.0 second for ground-fault currents equal to or greater than 3000 Amperes .

Testing Mandate (NEC 230.95(C)): The GFPE system must be performance tested when first installed in accordance with manufacturer instructions, with a written record submitted to the Authority Having Jurisdiction (AHJ). +-----------------------------------------------------------------------------+

  • | GFCI (PERSONNEL) VS. GFPE (EQUIPMENT) |
  • | |
  • | FEATURE CLASS A GFCI (NEC 210.8) GFPE (NEC 240.13/230.95) |
  • | ----------------------------------------------------------------------- |
  • | Primary Purpose Human Life / Shock Equipment / Fire Loss |
  • | Trip Current Level 4 to 6 Milliamperes (5 mA) 200 to 1200 Amperes |
  • | Operating Speed ~25 ms (1/40th sec) Up to 1.0 second delay |
  • | Standard Reference UL 943 UL 1053 |
  • +-----------------------------------------------------------------------------+

Exceptions to Mandatory GFPE (NEC 240.13):

Continuous Industrial Processes: Where an orderly shutdown is required to minimize hazards to personnel and equipment.

Fire Pumps (Article 695): Fire pump feeder disconnects are strictly prohibited from incorporating GFPE tripping to ensure water flow during a structural fire.

Health Care Facilities (NEC 517.17): Where GFPE is installed on the main service disconnect of a hospital, an additional downstream step of GFPE is required on the feeders, engineered with a minimum of 6 cycles (0.1 seconds) of selective time separation between the service and feeder devices.

2. Selective Coordination (NEC Article 100, 700.32 & 701.27)

Note

Where the over-1000-volt overcurrent rules went. The 2020 NEC kept feeder and branch-circuit overcurrent protection above 1000 volts in Article 240 Part IX, at 240.100 and 240.101. The 2023 NEC moved that material into a new Article 245, Overcurrent Protection for Systems Rated Over 1000 Volts ac, 1500 Volts dc . If a question sends you to 240.100 in a 2023 codebook, you will not find it there.

Definition of Selective Coordination

NEC Article 100 Definition: Localization of an overcurrent condition to restrict outages to the circuit or equipment affected, accomplished by the choice of overcurrent protective devices and their ratings or settings for the full range of overcurrents from overload to maximum available fault current, and for the full range of overcurrent protective device operating times associated with those overcurrents. +-----------------------------------------------------------------------------+

  • | SELECTIVE COORDINATION IN ACTION |
  • | |
  • | [ Utility Transformer (Available Fault Current = 42,000A) ] |
  • | | |
  • | [ Main Emergency Switchboard Breaker (OCPD-1: 800A) ] |
  • | | |
  • | +----------------------+----------------------+ |
  • | | | |
  • | [ Feeder Breaker (OCPD-2: 200A) ] [ Feeder Breaker (200A) ] |
  • | | | (Remains ON!) |
  • | [ Branch Breaker (OCPD-3: 20A) ] [ Surgical Suite / Egress ] |
  • | | |
  • | [ X ] BOLTED SHORT CIRCUIT ON BRANCH RECEPTACLE |
  • | |
  • | - NON-COORDINATED SYSTEM: OCPD-1, OCPD-2, and OCPD-3 all trip -> BLACKOUT!|
  • | - SELECTIVELY COORDINATED: ONLY OCPD-3 trips in 0.01 sec -> Emergency |
  • | lighting, surgical suites, and life safety stay 100% OPERATIONAL! |
  • +-----------------------------------------------------------------------------+

Where Is Selective Coordination Mandatory?

Selective coordination is not required for standard commercial branch circuits, but is strictly mandated by the NEC in mission-critical and life-safety systems:

Emergency Systems (NEC 700.32): Emergency lighting, exit signs, emergency ventilation.

Legally Required Standby Systems (NEC 701.27): Sewage lift pumps, communications, heating systems required by building codes.

Critical Operations Power Systems - COPS (NEC 708.54): Homeland security, 911 dispatch, military infrastructure.

Health Care Facilities Essential Electrical Systems (NEC 517.31(G)): Life safety and critical branch circuits in hospitals.

Multiple Elevators (NEC 620.62): Where more than one elevator is supplied by a single feeder.

Time-Current Characteristic Curves (TCC)

Selective coordination is proven by plotting the time-current curves (TCC) of upstream and downstream devices on log-log graph paper:

The total clearing curve of the downstream device must sit entirely below and to the left of the minimum melting curve / pickup curve of the upstream device.

There can be zero overlap across all fault currents up to the maximum available short-circuit current.

3. Series-Rated Systems vs. Fully Rated Systems (NEC 240.86 & 110.22)

When specifying equipment short-circuit interrupting ratings (AIC / AIR), electrical engineers utilize either fully rated systems or series-rated combinations: +-----------------------------------------------------------------------------+

  • | FULLY RATED VS. SERIES-RATED SYSTEMS |
  • | |
  • | FULLY RATED SYSTEM: |
  • | - Every individual circuit breaker has an interrupting rating (AIC) equal |
  • | to or greater than the maximum available fault current at its terminals.|
  • | - Example: Available fault = 42 kAIC -> All main, feeder, and branch |
  • | breakers are rated at least 42 kAIC. Robust, no special restrictions. |
  • | |
  • | SERIES-RATED COMBINATION (NEC 240.86): |
  • | - A lower-cost downstream breaker with lower AIC (e.g., 10 kAIC) is |
  • | protected by an upstream current-limiting fuse or breaker (e.g., 65 kAIC)|
  • | that reduces peak let-through energy. |
  • | - Combination must be UL tested and listed, or selected under engineering|
  • | supervision for existing installations (NEC 240.86(A)). |
  • +-----------------------------------------------------------------------------+
  • Field Labeling Requirements (NEC 110.22(B) & (C))

Panelboards and switchboards utilizing series ratings must be permanently field marked with a label stating:

  • "CAUTION — SERIES RATED SYSTEM — [____] AMPERES. IDENTIFIED REPLACEMENT COMPONENTS ONLY."
  • The Motor Contribution Prohibition (NEC 240.86(C))

During a short circuit, running electric motors act as induction generators for several cycles, back-feeding current directly into the fault. Because this back-fed motor current does not pass through the upstream current-limiting device, it can overpower and violently destroy a downstream 10 kAIC breaker. +-----------------------------------------------------------------------------+

  • | THE 1% MOTOR CONTRIBUTION LIMIT (NEC 240.86(C)) |
  • | |
  • | Series ratings SHALL NOT BE USED where the sum of motor full-load currents|
  • | (FLC) connected on the load side of the higher-rated device exceeds |
  • | ONE PERCENT (1%) of the interrupting rating of the lower-rated device: |
  • | |
  • | Sum of Connected Motor FLC > (0.01 x AIC_downstream) |
  • | ==> PROHIBITED! |
  • +-----------------------------------------------------------------------------+

Worked Example:

A commercial subpanel is protected by a series-rated combination where the downstream branch circuit breakers have an individual interrupting rating of 10,000 Amperes (10 kAIC) .

Calculate 1% limit: 10 , 000 A × 0.01 = 100 Amperes 10,000\text{ A} \times 0.01 = \mathbf{100\text{ Amperes}} 10 , 000 A × 0.01 = 100 Amperes .

If total full-load currents of all motors connected to this panel exceed 100 Amperes , the series-rated combination is strictly prohibited by NEC 240.86(C) , and fully rated circuit breakers must be installed.

Loading diagram... Ground-Fault Protection & Selective Coordination Engineering Workflow