Study guide

5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30)

Oklahoma Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety

1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection

2 Chapter 2: General Electrical Theory & Calculations

2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments

3 Chapter 3: General Installation Requirements (NEC Article 110)

3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable

4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)

4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)

5 Chapter 5: Services & Service Equipment (NEC Article 230)

5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)

6 Chapter 6: Electrical Load Calculations (NEC Article 220)

6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)

7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)

7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)

8 Chapter 8: Grounding and Bonding (NEC Article 250)

8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)

9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)

9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)

10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems

10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)

11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)

11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)

12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)

12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)

13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)

13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)

14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems

14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)

5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30)

Key Takeaways Explain This Topic AI

NEC 230.2 establishes the general rule that a building or structure shall be supplied by only one service, with specific exceptions for fire pumps, emergency systems, capacity exceeding 2,000A, different voltages/phases, or special occupancies.

NEC 230.9 mandates a minimum 3-foot clearance between open service conductors and windows that open, doors, porches, balconies, stairs, and fire escapes, with an exemption for conductors installed above the top level of a window.

Under NEC 230.24(B), overhead service-drop vertical clearances above grade are 10 ft for pedestrian-only areas, 12 ft over residential driveways, 18 ft over public streets/alleys/truck areas, and 24.5 ft over railroad tracks.

Overhead roof clearances under NEC 230.24(A) require 8 ft general clearance, reducible to 3 ft for roof pitch ≥ 4/12 (≤ 300V), and 18 inches for through-the-roof service masts located within 4 ft of the roof edge with max 6 ft of conductor over the roof.

Underground service lateral raceways entering buildings must be sealed per NEC 230.8 and 300.5(G), and emerging conductors must be protected against physical damage using RMC, IMC, or Schedule 80 PVC from 18 in. below grade to at least 8 ft above grade.

Last updated: August 2026

Service Clearances, Overhead & Underground Service-Drop Requirements (NEC Article 230)

Article 230 of the National Electrical Code governs the installation, conductors, and equipment for control and protection of services—the vital link where utility-supplied power enters a customer's electrical distribution system. Because service conductors operate ahead of the main overcurrent protective device (OCPD), they carry immense available fault current and represent a unique fire and shock hazard. On the Oklahoma Journeyman Electrician examination, mastering service supply rules, clearance envelopes, structural mast limitations, and underground burial depths is essential for code compliance and public safety.

1. Number of Services Permitted (NEC 230.2)

As a foundational safety standard, NEC 230.2 establishes the general rule:

"A building or other structure served shall be supplied by only one service unless permitted in 230.2(A) through (D)."

Limiting a structure to a single service ensures that emergency first responders (such as firefighters) and service electricians can completely de-energize the entire building from a single concentrated location without leaving energized backfeeds. +-----------------------------------------------------------------------------+

  • | EXCEPTIONS TO THE "ONE SERVICE" RULE (NEC 230.2) |
  • | |
  • | [A. Special Conditions] [B. Special Occupancies] |
  • | - Fire pumps - Multiple-occupancy buildings with no |
  • | - Emergency / Standby systems common equipment access (special perm) |
  • | - Parallel solar PV / energy - Exceptionally large buildings |
  • | storage power sources [D. Different Characteristics] |
  • | [C. Capacity Requirements] - Different voltages (480V vs 208V) |
  • | - Calculated load > 2,000A - Different frequencies or phases |
  • | - Single-phase utility limits - Different utility billing rate tariffs |
  • +-----------------------------------------------------------------------------+
  • Mandatory Identification Plaques (NEC 230.2(E))

Where a building is supplied by more than one service, or by a combination of feeders, branch circuits, and services, a permanent plaque or directory must be installed at each service disconnect location denoting all other services, feeders, and branch circuits supplying that building and the specific area or equipment served by each.

2. Clearances from Building Openings (NEC 230.9)

Service conductors installed as open conductors, multiconductor cables without an overall outer jacket, or cabled service-drop conductors must maintain safe physical separation from building openings where occupants could reach out and contact energized lines. +-----------------------------------------------------------------------------+

  • | CLEARANCE FROM BUILDING OPENINGS (NEC 230.9) |
  • | |
  • | +------------------------+ |
  • | | Conductors Above Top | <-- EXEMPT from 3-ft rule |
  • | | Level of Window Frame | (Permitted overhead) |
  • | +------------------------+ |
  • | | |
  • | +--------------------+ |
  • | | OPERABLE WINDOW | |
  • | <--- 3 Feet ---> | OR DOOR OPENING | <--- 3 Feet ---> |
  • | Clearance Required +--------------------+ Clearance Required |
  • | | |
  • | <--- 3 Feet Below ---> |
  • +-----------------------------------------------------------------------------+

Key Clearance Rules under NEC 230.9:

3-Foot Minimum Clearance (230.9(A)): Service conductors must have a clearance of not less than 3 feet (900 mm) from windows that open, doors, porches, balconies, ladders, stairs, fire escapes, or similar locations.

The Above-Window Exemption: Service conductors installed above the top level of a window are exempt from the 3-foot requirement because occupants cannot lean or reach upward out of an open window sash to contact overhead conductors.

Prohibition Below Openings (230.9(C)): Service conductors shall NOT be installed underneath openings through which materials might be moved (e.g., commercial second-story delivery doors, hayloft openings in agricultural structures) and shall not obstruct entrance to these building openings.

3. Overhead Service-Drop & Conductor Clearances (NEC 230.24)

Overhead service spans must maintain strict vertical and horizontal clearances above ground, roads, driveways, platforms, and roofs to prevent contact with vehicles, pedestrians, and maintenance personnel.

Vertical Clearance Above Grade (NEC 230.24(B))

Location / Surface Classification Minimum Vertical Clearance Voltage & Application Limits

Pedestrian walkways, sidewalks, finished grade, decks 10 feet (3.0 m) For conductors rated ≤ 150V to ground (e.g., 120/240V 1-ph, 208Y/120V 3-ph)

Residential driveways & commercial areas (no truck traffic) 12 feet (3.7 m) Voltage ≤ 300V to ground

Residential driveways & commercial areas (no truck traffic) 15 feet (4.5 m) Voltage > 300V to ground (e.g., 480Y/277V systems)

Public streets, alleys, roads, parking areas (truck traffic) 18 feet (5.5 m) All public roadways, commercial driveways, and agricultural cultivated land

Railroad track rails 24.5 feet (7.5 m) Overhead spans crossing railroad tracks +-----------------------------------------------------------------------------+

  • | OVERHEAD SERVICE CLEARANCE ENVELOPE (NEC 230.24) |
  • | |
  • | [24.5 ft] ============================================= Railroad Tracks |
  • | [18.0 ft] ============================================= Public Streets |
  • | [15.0 ft] ============================================= Driveway (>300V) |
  • | [12.0 ft] ============================================= Driveway (≤300V) |
  • | [10.0 ft] ============================================= Sidewalk / Grade |
  • +-----------------------------------------------------------------------------+
  • Clearances Over Roofs (NEC 230.24(A))

General Rule: Overhead service conductors must maintain a vertical clearance of not less than 8 feet (2.5 m) above the roof surface. This clearance must be maintained for a distance of at least 3 feet (900 mm) in all directions from the edge of the roof.

Exception 1 (Sloped Roofs ≥ 4/12 Pitch): Where the voltage between conductors does not exceed 300 volts, and the roof has a slope of not less than 4 inches in 12 inches (4/12 pitch or 33.3% slope), the clearance may be reduced to 3 feet (900 mm) .

Exception 2 (Through-the-Roof Service Mast / Overhang): Where conductors pass over only the overhanging portion of the roof (eaves/overhang), the clearance may be reduced to 18 inches (450 mm) provided:

Voltage between conductors does not exceed 300 volts.

Conductors pass over not more than 4 feet (1.2 m) of the roof overhang measured horizontally.

Conductors terminate at a through-the-roof service raceway (mast) or approved support located within 4 feet of the roof edge.

A maximum of 6 feet (1.8 m) of conductor length passes over the roof surface.

Roofs Subject to Pedestrian Traffic: Where roofs, balconies, or decks are accessible to pedestrian traffic, service conductors must maintain a vertical clearance of at least 10 feet (3.0 m) per 230.24(B). +-----------------------------------------------------------------------------+

  • | ROOF OVERHANG 18-INCH CLEARANCE EXCEPTION |
  • | |
  • | Service Drop Conductor |
  • | ========================\ |
  • | \ Min. 18 in. Clearance |
  • | \ |
  • | +------------------[Weatherhead] |
  • | | | | |
  • | | | | Service Mast |
  • | | Roof Overhang | | (Within 4 ft of edge) |
  • | +==================+===+===== |
  • | | <--- Max 4 ft ---> | |
  • | | (Max 6 ft wire) | Building Wall |
  • +-----------------------------------------------------------------------------+
  • 4. Service Mast Structural Support (NEC 230.28)

Where a conduit raceway serves as a through-the-roof service mast to support overhead service-drop or service conductors, it is subjected to severe mechanical cantilever forces from conductor weight, wind drag, and winter ice accumulation.

NEC 230.28 Requirements:

Mechanical Strength: Service masts must have adequate mechanical strength or be supported by braces or guy wires to withstand the mechanical strain imposed by the service drop.

Permitted Raceway Types: Only rigid metal conduit (RMC) or intermediate metal conduit (IMC) are typically approved by utility specifications and AHJs as structural service masts. Electrical Metallic Tubing (EMT) and PVC conduit lack structural strength and are strictly prohibited from serving as mast supports.

Prohibition on Foreign Attachments (NEC 230.28(B)): Service masts shall NOT be used to attach or support other non-electrical systems. Attaching telephone, cable television (CATV), broadband data drops, satellite dishes, or radio antennas to an electrical service mast is a direct code violation.

5. Underground Service Lateral Requirements (NEC 230.30–230.32)

Underground service conductors (service laterals) are installed below grade from the utility distribution transformer or handhole to the building meter base or main service panel.

Permitted Wiring Methods (NEC 230.30):

Direct-burial underground service-entrance cable (Type USE or USE-2).

Rigid Metal Conduit (RMC) and Intermediate Metal Conduit (IMC).

Rigid Polyvinyl Chloride (PVC) Conduit (Schedule 40 or Schedule 80).

High-Density Polyethylene (HDPE) Conduit and Reinforced Thermosetting Resin Conduit (RTRC).

Minimum Burial Depths (NEC Table 300.5(A)):

Direct-Burial Cable (Type USE): 24 inches minimum cover.

Rigid PVC Conduit (Schedule 40/80): 18 inches minimum cover (reduced to 4 inches if encased beneath a 4-inch concrete slab).

Rigid Metal Conduit (RMC) / Intermediate Metal Conduit (IMC): 6 inches minimum cover.

Under Public Roads, Streets, & Commercial Driveways: 24 inches minimum cover for all wiring methods.

Protection from Physical Damage & Building Entry Sealing:

Mechanical Protection (NEC 230.32 & 300.5(D)): Conductors emerging from the ground must be protected in listed raceways (RMC, IMC, or Schedule 80 PVC) starting at least 18 inches below finished grade up to their point of termination or at least 8 feet above grade .

Raceway Sealing (NEC 230.8 & 300.5(G)): Underground raceways entering a building from below grade must be sealed with a listed duct-seal compound or expanding foam plug at the building entry point to prevent moisture, subterranean water, radon, and sewer/combustible gases from migrating into the electrical equipment.

Loading diagram... Overhead and Underground Service Clearance & Protection Workflow (NEC Article 230)