Study guide
14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680)
Oklahoma Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety
1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection
2 Chapter 2: General Electrical Theory & Calculations
2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments
3 Chapter 3: General Installation Requirements (NEC Article 110)
3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable
4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)
4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)
5 Chapter 5: Services & Service Equipment (NEC Article 230)
5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)
6 Chapter 6: Electrical Load Calculations (NEC Article 220)
6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)
7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)
7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)
8 Chapter 8: Grounding and Bonding (NEC Article 250)
8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)
9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)
9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)
10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems
10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)
11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)
11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)
12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)
12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)
13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)
13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)
14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems
14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)
14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680)
Key Takeaways Explain This Topic AI
NEC Table 680.9 establishes strict overhead clearances (22.5 ft above water, 14.5 ft above diving platforms), while 680.11 prohibits underground wiring within 5 ft horizontally unless space-constrained in approved raceways.
NEC 680.26 mandates an equipotential bonding grid using #8 AWG solid bare copper to eliminate voltage gradients across the pool shell, 3-foot perimeter surface (tied at ≥4 points), metallic equipment, forming shells, and water (≥9 sq. in. contact).
Under NEC 680.21(C), Ground-Fault Circuit-Interrupter (GFCI) protection is mandatory for ALL outlets supplying swimming pool pump motors on branch circuits rated 120V through 240V, up to 60 amperes.
Underwater luminaires (NEC 680.23) require GFCI protection and potting, while deck junction boxes (680.24) must be listed, elevated ≥4 in. above deck / ≥8 in. above water level, and located ≥4 ft from inside pool wall.
Spas and hot tubs (NEC Article 680 Part IV) require a readily accessible emergency shutoff switch within sight and ≥5 ft away, while hydromassage bathtubs (Part VII) require individual GFCI circuits and accessible equipment.
Last updated: August 2026
Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (NEC Article 680)
Water and electricity present an exceptionally hazardous combination. When the human body is immersed in water or standing on wet concrete decks, skin resistance drops precipitously from thousands of ohms to less than 500 ohms. Under these conditions, minute stray currents—as low as 10 to 20 milliamperes—can cause muscular tetany (inability to let go), drowning, or fatal ventricular fibrillation. Consequently, NEC Article 680 establishes rigorous engineering protocols governing equipment location, overhead/underground clearances, Ground-Fault Circuit-Interrupter (GFCI) protection, and equipotential bonding grids.
1. Overhead and Underground Clearances (NEC 680.9 & 680.11)
To prevent physical contact with energized lines during maintenance (such as handling long aluminum skimmer poles) or inadvertent conductor flashover, the NEC establishes severe clearance boundaries surrounding swimming pools, diving structures, and observation stands. +-----------------------------------------------------------------------------+
- | OVERHEAD CLEARANCES OVER SWIMMING POOLS (NEC TABLE 680.9) |
- | |
- | CONDUCTOR VOLTAGE & TYPE CLEARANCE ABOVE CLEARANCE ABOVE |
- | MAX WATER LEVEL DIVING PLATFORM |
- | ----------------------------------------------------------------------- |
- | - 0–750V Insulated Cable (with 22.5 Feet (6.86 m) 14.5 Feet (4.42 m)|
- | grounded bare neutral / triplex) |
- | - 0–750V Open Supply Conductors 22.5 Feet (6.86 m) 14.5 Feet (4.42 m)|
- | - Over 750V to 22 kV (Phase-to-Grnd) 25.0 Feet (7.62 m) 17.0 Feet (5.18 m)|
- | - Over 22 kV to 50 kV 27.0 Feet (8.23 m) 19.0 Feet (5.79 m)|
- | - Network-Powered Broadband / Comms 22.5 Feet (6.86 m) 14.5 Feet (4.42 m)|
- +-----------------------------------------------------------------------------+
- Clearance Envelope Rules (NEC 680.9)
Horizontal Clearance Envelope: The overhead clearance limits extend horizontally 10 feet (3.05 m) beyond the inside edge of the pool walls, diving structures, observation stands, and observation towers.
Utility Service Drops & Service Conductors: Utility service drops and open overhead conductors must not pass directly over swimming pools, storable pools, outdoor spas, or diving towers unless installed at or above the minimum heights specified in Table 680.9.
Underground Wiring Clearances (NEC 680.11) +-----------------------------------------------------------------------------+
- | UNDERGROUND WIRING RESTRICTIONS (NEC 680.11) |
- | |
- | [RESTRICTED ZONE] [PERMITTED ZONE] |
- | <------------------------ 5 Feet ------------------------> |
- | +-----------------------+ |
- | | | Underground wiring prohibited |
- | | POOL WATER | under pool or within 5 ft horizontally. |
- | | | |
- | | (Inside Pool Wall) | EXCEPTION: Where space is limited, wiring |
- | | | | permitted in RMC, IMC, PVC, or RTRC with |
- | +-----------|-----------+ strict minimum cover depths. |
- | v |
- | (0 to 5 Feet) (Beyond 5 Feet) |
- | Wiring Prohibited (unless Standard Chapter 3 underground |
- | raceway exception applies) burial depths apply (Table 300.5(A)) |
- +-----------------------------------------------------------------------------+
General Prohibition: Underground wiring is strictly prohibited beneath a pool structure or within the zone extending 5 feet (1.52 m) horizontally from the inside wall of the pool.
Limited Space Exception: Where installation space is physically constrained (such as between a property line and the pool deck), underground wiring is permitted within the 5-foot zone provided it is installed in one of the following approved raceways:
Rigid Metal Conduit (RMC) — Minimum cover depth: 6 inches (150 mm) .
Intermediate Metal Conduit (IMC) — Minimum cover depth: 6 inches (150 mm) .
Schedule 80 or Schedule 40 Rigid Polyvinyl Chloride (PVC) — Minimum cover depth: 18 inches (450 mm) .
Reinforced Thermosetting Resin Conduit (RTRC) — Minimum cover depth: 18 inches (450 mm) .
2. Equipotential Bonding Grid (NEC 680.26)
Equipotential bonding is the single most critical safety mechanism in pool electrical installations. Bonding is NOT equipment grounding. While equipment grounding clears ground faults by providing a low-impedance path back to the electrical source to trip the overcurrent device, equipotential bonding eliminates voltage gradients across the pool structure, deck, equipment, and water. By tying all conductive surfaces together to a common reference plane, the electrical potential between any two touchable surfaces is reduced to zero, completely preventing current from flowing through a bather's body. +-----------------------------------------------------------------------------+
- | EQUIPOTENTIAL BONDING SYSTEM (NEC 680.26) |
- | |
- | BONDING CONDUCTOR SPECIFICATION: |
- | - Minimum Size: #8 AWG Solid Bare Copper Conductor (Stranded Prohibited!) |
- | - Connections: Listed pressure connectors (copper/brass), exothermic |
- | welds, or stainless steel clamps (NEC 680.26(D)). |
- | |
- | BONDED ELEMENTS (NEC 680.26(B)): |
- | 1. Conductive Pool Shell (Structural Rebar or #8 Cu Grid 12"x12"). |
- | 2. Perimeter Surface (Extends 3 ft horizontally, 4–6 in. below grade, |
- | attached to pool shell at minimum 4 uniformly spaced points). |
- | 3. Metallic Pool Equipment (Pumps, Heaters, Filters, Chlorinators). |
- | 4. Metallic Structural Parts (Ladders, Handrails, Diving Stands). |
- | 5. Underwater Light Forming Shells & Mounting Brackets (680.26(B)(4)). |
- | 6. Pool Water (Intentional contact with min 9 sq. in. conductive surface).|
- +-----------------------------------------------------------------------------+
- The 6 Mandatory Bonded Components (NEC 680.26(B))
Conductive Pool Shell (680.26(B)(1)):
Structural Concrete Pools: The unencapsulated structural steel rebar grid tied together with steel tie wires satisfies the bonding grid requirement. If rebar is epoxy-coated or nonconductive, an independent copper grid consisting of #8 AWG solid bare copper arranged in a 12 in. × 12 in. grid must be installed conforming to the pool contour.
Poured / Vinyl / Fiberglass Pools: Nonconductive shells require a copper bonding grid installed directly beneath the pool liner/shell.
Perimeter Surface Bonding (680.26(B)(2)):
Extends 3 feet (1 meter) horizontally beyond the inside walls of the pool.
Must be installed 4 to 6 inches (100 to 150 mm) below the subgrade.
Constructed of either structural deck rebar, a copper mesh grid, or a single continuous #8 AWG solid bare copper conductor encircling the pool perimeter.
The perimeter bonding ring must be connected to the pool shell grid at a minimum of 4 uniformly spaced points around the pool perimeter.
Metallic Structural Components (680.26(B)(3)):
Metal ladders, handrails, safety stanchions, diving board bases, and forming brackets must be bonded to the #8 copper grid.
Underwater Light Forming Shells (680.26(B)(4)):
Wet-niche forming shells and mounting brackets for no-niche luminaires must connect to the bonding grid.
Metal Fittings & Equipment (680.26(B)(5)):
Metal parts of electrical equipment associated with the pool water circulating system (pump motors, pool heaters, heat pumps, ozone generators, chemical feeders) must be bonded. Double-insulated pump motors are exempt from internal bonding, but an external #8 solid copper pigtail must be provided to bond to the grid.
Pool Water Bonding (680.26(C)):
The pool water must be intentionally bonded to the equipotential grid. The bonding connection must consist of a corrosion-resistant metallic surface (such as a conductive bronze fitting, metallic pool light forming shell, or listed inline pipe bond) with not less than 9 square inches ( 58 cm 2 58\text{ cm}^2 58 cm 2 ) of conductive surface area in direct contact with pool water at all times.
3. Pool Pump Motor & Equipment GFCI Protection (NEC 680.21)
Electric pump motors operate under continuous vibration and exposure to splashing water, chemical vapors, and moisture condensation. NEC 680.21 enforces universal ground-fault protection to prevent fatal shocks from motor winding insulation degradation: +-----------------------------------------------------------------------------+
- | POOL PUMP MOTOR GFCI PROTECTION MANDATE (NEC 680.21(C)) |
- | |
- | APPLICATION: |
- | - All Outlets supplying pool pump motors. |
- | - Single-Phase or Three-Phase. |
- | - Rated 120 Volts through 240 Volts. |
- | - Rated up to and including 60 Amperes. |
- | - Cord-and-Plug Connected OR Hardwired (Direct Conduit Connection). |
- | |
- | PROTECTION REQUIREMENT: |
- | - Class A GFCI Protection (Trips at 4 mA to 6 mA ground-fault current). |
- +-----------------------------------------------------------------------------+
- Disconnecting Means for Pool Equipment (NEC 680.13)
A disconnecting means must be provided for all pool utilization equipment, heaters, and pump motors.
Location: Must be located in sight from the controller and pool equipment, and located at least 5 feet (1.52 m) horizontally from the inside wall of the pool (unless separated by a permanent barrier, wall, or fence).
4. Underwater Luminaires & Junction Deck Boxes (NEC 680.23 & 680.24)
Underwater pool luminaires are classified into wet-niche, dry-niche, no-niche, and submersible fixtures: +-----------------------------------------------------------------------------+
- | UNDERWATER LUMINAIRE CLASSIFICATIONS (NEC 680.23) |
- | |
- | LUMINAIRE TYPE OPERATING VOLTAGE MANDATORY SAFETY RULES |
- | ----------------------------------------------------------------------- |
- | - Line-Voltage 120 Volts Nominal - Class A GFCI protected |
- | Wet-Niche Fixture - Forming shell grounded |
- | - Potting compound seal |
- | - Low-Voltage <= 15V AC (RMS) / - Listed isolating pool |
- | Luminaire <= 30V DC Continuous transformer / supply |
- | (Low-Voltage Limit) - GFCI on supply side |
- +-----------------------------------------------------------------------------+
- Wet-Niche Luminaire Wiring & Potting (NEC 680.23(B))
Raceway Requirement: Conduit connecting the forming shell to the junction box must be Rigid Metal Conduit (brass or corrosion-resistant metal) or Schedule 80/40 Rigid PVC Conduit .
Equipment Grounding Conductor: An insulated copper equipment grounding conductor (EGC), sized per NEC 250.122 but never smaller than #12 AWG , must be installed inside the raceway without splices.
Corrosion-Resistant Potting (NEC 680.23(B)(2)(b)): Where a nonmetallic conduit (PVC) is run between the forming shell and junction box, a #8 AWG solid insulated or bare copper bonding jumper must be terminated inside the forming shell and encapsulated in a listed, non-hardening, corrosion-resistant potting compound to prevent swimming pool water from corroding the grounding terminal.
Junction Boxes & Deck Boxes (NEC 680.24)
Junction boxes (deck boxes) connected to wet-niche forming shells provide the dry transition point between branch-circuit wiring and the luminaire's flexible underwater cord: +-----------------------------------------------------------------------------+
- | DECK BOX ELEVATION & DISTANCE (NEC 680.24) |
- | |
- | [LISTED DECK BOX] |
- | | |
- | +---------------+---------------+ |
- | | | |
- | >= 4 Inches (100 mm) >= 8 Inches (200 mm) |
- | above Finished Deck / Grade above Maximum Pool Water Level |
- | | | |
- | +---------------+---------------+ |
- | | |
- | HORIZONTAL DISTANCE: >= 4 Feet (1.22 m) from Inside Pool Wall |
- | (Unless separated by a permanent solid wall or barrier) |
- +-----------------------------------------------------------------------------+
Elevation Requirement (680.24(A)(2)): The junction box must be installed not less than 4 inches (100 mm) above the finished deck/ground level, OR not less than 8 inches (200 mm) above the maximum water level, whichever elevation is higher.
Horizontal Distance (680.24(A)(2)): The box must be located not less than 4 feet (1.22 m) horizontally from the inside wall of the pool.
Construction (680.24(A)(1)): Must be listed for swimming pool junction box application, constructed of brass, stainless steel, or approved nonmetallic material, and equipped with threaded hubs and an integrated copper grounding bar with grounding terminals.
5. Spas, Hot Tubs & Hydromassage Bathtubs (NEC Article 680 Parts IV & VII) +-----------------------------------------------------------------------------+
- | SPAS, HOT TUBS & HYDROMASSAGE COMPARISON |
- | |
- | EQUIPMENT NEC PART KEY INSTALLATION REQUIREMENTS |
- | ----------------------------------------------------------------------- |
- | - Outdoor Spas & Part IV - Emergency shutoff switch within sight|
- | Hot Tubs and >= 5 ft horizontally. |
- | - GFCI protection for all equipment. |
- | - Equipotential bonding required. |
- | - Indoor Spas & Part IV - Receptacles min 6 ft away (GFCI <=10ft)|
- | Hot Tubs - Lighting >= 7 ft 6 in. (or 5 ft GFCI)|
- | - Hydromassage Part VII - Individual branch circuit required. |
- | Bathtubs - GFCI protection on pump and controls.|
- | - Pump/electrical equipment ACCESSIBLE |
- | without damaging building structure. |
- +-----------------------------------------------------------------------------+
- Emergency Shutoff Switch (NEC 680.41)
In public and commercial spas or hot tubs, a clearly labeled emergency shutoff switch or control must be installed to instantly de-energize the recirculation pump and jet system.
Location: Must be readily accessible , located in sight from the spa/hot tub, and located not less than 5 feet (1.52 m) horizontally from the inside wall of the spa/hot tub.
Hydromassage Bathtub Accessibility & Circuit Rules (NEC 680.70–680.73)
Individual Branch Circuit (680.71): Hydromassage bathtubs and their associated electrical components must be supplied by an individual branch circuit protected by a Class A GFCI.
Accessibility (680.73): The circulation pump motor, electrical controls, and receptacle outlets must be accessible without damaging the building finish or structural components . An access panel or opening of sufficient size (typically min 12 in. × 12 in.) must be provided directly adjacent to the pump equipment.