Study guide
12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427)
Oklahoma Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety
1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection
2 Chapter 2: General Electrical Theory & Calculations
2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments
3 Chapter 3: General Installation Requirements (NEC Article 110)
3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable
4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)
4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)
5 Chapter 5: Services & Service Equipment (NEC Article 230)
5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)
6 Chapter 6: Electrical Load Calculations (NEC Article 220)
6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)
7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)
7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)
8 Chapter 8: Grounding and Bonding (NEC Article 250)
8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)
9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)
9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)
10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems
10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)
11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)
11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)
12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)
12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)
13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)
13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)
14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems
14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)
12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427)
Key Takeaways Explain This Topic AI
NEC 426.28 requires ground-fault protection of equipment for fixed outdoor electric deicing and snow-melting equipment, using devices that respond to leakage in the range of roughly 6 to 50 milliamperes rather than the 4 to 6 milliamperes of a Class A GFCI.
NEC 427.22 requires ground-fault protection of equipment for electric heat tracing and heating panels on pipelines and vessels, relieved only in industrial establishments with ground-fault alarm indication and qualified maintenance and supervision.
NEC 427.13 requires caution signs or permanent markings indicating the presence of electrically heated pipelines or vessels at intervals not exceeding 20 feet along the pipeline or vessel and on or adjacent to the equipment.
Fixed electric deicing, snow-melting, pipeline, and vessel heating loads are continuous loads, so branch-circuit conductors and overcurrent devices are sized at 125 percent of the total heating load.
Article 424 covers fixed electric space-heating equipment inside a building, Article 426 covers fixed outdoor deicing and snow-melting, and Article 427 covers fixed heating applied to pipelines and vessels — the PSI outline groups all three under "space-heating, snow-melting, and pipe-heating circuits."
Last updated: August 2026
12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427)
The PSI outline lists space-heating, snow-melting, and pipe-heating circuits as a single sub-topic, but the Code splits that work across three articles. Knowing which article to open is half the question:
Application Article Typical equipment
Fixed electric space heating inside a building 424 Baseboard heaters, unit heaters, duct heaters, radiant ceiling panels
Fixed outdoor electric deicing and snow-melting 426 Embedded driveway and sidewalk cable, roof and gutter deicing cable, ramp heating panels
Fixed electric heating for pipelines and vessels 427 Self-regulating heat trace, series resistance cable, induction and skin-effect heating, heating panels and jackets
1. Article 426 — Fixed Outdoor Electric Deicing and Snow-Melting Equipment
Article 426 applies to embedded or exposed heating equipment installed outdoors in driveways, walkways, steps, ramps, roofs, gutters, downspouts, and similar areas. Three concepts carry the article.
Installation types
Embedded (Part II). Heating cable, panels, or units are cast into concrete, masonry, or asphalt. The Code addresses spacing between adjacent runs so heating elements do not overheat each other, prohibits panels or units from bridging expansion joints unless protection against expansion and contraction is provided, requires that cable ends be terminated and insulated before the pour, and requires that the installation be inspected and tested before the covering material is applied.
Exposed (Part III). Cable installed on roofs, in gutters, and on downspouts must be secured with means that will not damage the sheath and must be arranged so that ice and snow loading cannot pull the cable loose.
Skin-effect heating (Part IV). A ferromagnetic tube with an insulated conductor inside carries current that returns on the inner surface of the tube; the tube itself is not a raceway in the ordinary sense but is treated as an enclosure for the internal conductor.
Ground-fault protection of equipment (426.28)
NEC 426.28 requires ground-fault protection of equipment for fixed outdoor electric deicing and snow-melting equipment. This is not a Class A GFCI:
- Device Trip threshold Purpose
- Class A GFCI 4–6 mA Protects people from electrocution
GFPE for heating equipment Typically 6–50 mA Protects the equipment and the structure from arcing ground faults in a wet, ice-loaded, mechanically abused cable
The protection may be built into the branch-circuit breaker (a GFPE-rated breaker) or supplied as an integral device that is part of the listed deicing or snow-melting equipment.
Identification, use, and control
426.13 requires that the presence of deicing or snow-melting equipment be made evident by posted caution signs or permanent markings on fixed pedestals and equipment, so someone drilling an anchor into a heated slab has been warned.
426.11 requires the equipment to be identified as suitable for the chemical, thermal, and physical environment in which it is installed.
426.4 treats the fixed outdoor electric deicing and snow-melting load as a continuous load , which means the branch-circuit conductors and overcurrent device are sized at 125 percent of the load.
426.14 permits certain installations only with special permission from the authority having jurisdiction.
Part V covers controllers and disconnecting means : the equipment must have a means of disconnect, and where the heating equipment is supplied by a remote panel, the disconnecting means must be capable of being locked in the open position.
2. Article 427 — Fixed Electric Heating Equipment for Pipelines and Vessels
Article 427 covers electrically energized heating systems and their controls applied to pipelines and vessels — freeze protection on a fire-suppression standpipe, viscosity maintenance on a fuel-oil line, and process temperature maintenance in a refinery are all Article 427 work.
The five heating technologies
Resistance heating elements — self-regulating or constant-wattage heat trace cable spiraled or straight-traced along the pipe under insulation.
Impedance heating — current is passed through the pipe itself, with the pipe acting as the resistive element; the voltage is limited and the pipe must be effectively grounded.
Induction heating — an isolated coil around the pipe induces current in the pipe wall.
Skin-effect heating — an insulated conductor inside a ferromagnetic tube welded to the pipe.
Heating panels and jackets applied to vessels.
The three rules the exam asks for
427.13 Identification. The presence of electrically heated pipelines or vessels must be evident by caution signs or markings at intervals not exceeding 20 feet (6.0 m) along the pipeline or vessel and on or adjacent to the equipment. A welder cutting into an unmarked traced line is exactly the hazard this rule addresses.
427.22 Equipment protection. Ground-fault protection of equipment is required for electric heat tracing and heating panels. The single exception is for industrial establishments where there is alarm indication of ground faults and where conditions of maintenance and supervision ensure that only qualified persons service the installed systems — a plant may then trade automatic disconnection for monitored operation, because losing freeze protection can itself be a hazard.
Disconnecting means. Means must be provided to disconnect all ungrounded conductors of each heating application, and where the heating equipment is remote from its supply, the disconnect must be lockable in the open position.
Installation practice that shows up as a scenario
Heat trace is installed under the thermal insulation, and the insulation must be kept dry — wet insulation destroys both the heating performance and the cable.
The thermostat or controller sensing bulb must be located on the pipe, not in the ambient air, unless the system is designed for ambient sensing.
Heating cable may not be installed through walls where it will be concealed unless the specific installation is permitted by the article, and cable ends must be terminated with listed kits.
Heating loads are continuous loads — size branch-circuit conductors and the overcurrent device at 125 percent of the total heating load.