Study guide

12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B))

Oklahoma Journeyman Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety

1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection

2 Chapter 2: General Electrical Theory & Calculations

2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments

3 Chapter 3: General Installation Requirements (NEC Article 110)

3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable

4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)

4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)

5 Chapter 5: Services & Service Equipment (NEC Article 230)

5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)

6 Chapter 6: Electrical Load Calculations (NEC Article 220)

6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)

7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)

7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)

8 Chapter 8: Grounding and Bonding (NEC Article 250)

8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)

9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)

9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)

10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems

10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)

11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)

11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)

12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)

12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)

13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)

13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)

14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems

14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)

12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B))

Key Takeaways Explain This Topic AI

Single-phase transformer full-load current is calculated as I = (kVA × 1000) / V, whereas three-phase full-load current is calculated as I = (kVA × 1000) / (√3 × V) = (kVA × 1000) / (1.732 × V).

Under NEC Table 450.3(B) for transformers ≤1000V with primary-only protection, primary currents ≥9A are permitted a maximum OCPD of 125% FLC (Note 1 round-up allowed), currents 2A to <9A are capped at 167% FLC (round down), and currents <2A are capped at 300% FLC.

When both primary and secondary overcurrent protection are provided under NEC Table 450.3(B), the primary OCPD may be sized up to 250% FLC (with Note 1 next-size-up permitted), and secondary protection for currents 9A or greater is sized at a maximum of 125% FLC (with Note 1 next-size-up permitted).

Transformer secondary conductors are not protected by primary overcurrent devices (except 2-wire single-phase and 3-wire 3-phase delta-delta systems) and must comply with the secondary conductor tap rules of NEC 240.21(C) (10-foot, 25-foot, or outside tap rules).

Dry-type transformers must be readily accessible per NEC 450.13, except dry-type units 50 kVA or less and 1000V or less are permitted in accessible hollow spaces if fire-resistant, and all transformers require at least 6 inches of clearance from walls for proper ventilation under NEC 450.9.

Last updated: August 2026

Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B))

Transformers are electromagnetic devices that transfer electrical energy between circuits through mutual induction. They allow electrical distribution systems to step voltages up for efficient long-distance transmission and step voltages down for safe utilization in commercial and industrial premises. On the Oklahoma Journeyman Electrician examination, mastering NEC Article 450 requires a fluent command of transformer formulas, full-load current (FLC) calculations, precise overcurrent protection thresholds from Table 450.3(B) , secondary conductor tap rules from NEC 240.21(C) , and physical installation clearances.

1. Fundamental Transformer Formulas & Full-Load Currents

Transformers are rated in kilovolt-amperes (kVA), which represents apparent power ( S S S ). In an ideal transformer, input power equals output power ( k V A primary = k V A secondary kVA_{\text{primary}} = kVA_{\text{secondary}} kV A primary ​ = kV A secondary ​ ), meaning voltage and current vary inversely with the turns ratio ( N p / N s = V p / V s = I s / I p N_p / N_s = V_p / V_s = I_s / I_p N p ​ / N s ​ = V p ​ / V s ​ = I s ​ / I p ​ ). +-----------------------------------------------------------------------------+

  • | TRANSFORMER FULL-LOAD CURRENT FORMULAS |
  • | |
  • | SINGLE-PHASE (1Ø): |
  • | kVA × 1000 kVA × 1000 |
  • | I_primary = ------------------ = ------------ |
  • | V_primary V_p |
  • | |
  • | kVA × 1000 kVA × 1000 |
  • | I_secondary = ------------------ = ------------ |
  • | V_secondary V_s |
  • | |
  • | THREE-PHASE (3Ø): |
  • | kVA × 1000 kVA × 1000 |
  • | I_primary = ---------------------------- = ----------------------- |
  • | √3 × V_primary(Line-to-Line) 1.732 × V_p(L-L) |
  • | |
  • | kVA × 1000 kVA × 1000 |
  • | I_secondary = ---------------------------- = ----------------------- |
  • | √3 × V_secondary(Line-to-Line) 1.732 × V_s(L-L) |
  • +-----------------------------------------------------------------------------+

Worked Calculation Examples:

Example 1: Single-Phase Transformer Full-Load Current

A 25 kVA , 480 V 480\text{V} 480 V primary to 120 / 240 V 120/240\text{V} 120/240 V single-phase dry-type transformer: I primary = 25 × 1000 480 V = 25000 480 = 52.08 Amperes I_{\text{primary}} = \frac{25 \times 1000}{480\text{ V}} = \frac{25000}{480} = \mathbf{52.08\text{ Amperes}} I primary ​ = 480 V 25 × 1000 ​ = 480 25000 ​ = 52.08 Amperes I secondary (240V) = 25 × 1000 240 V = 25000 240 = 104.17 Amperes I_{\text{secondary (240V)}} = \frac{25 \times 1000}{240\text{ V}} = \frac{25000}{240} = \mathbf{104.17\text{ Amperes}} I secondary (240V) ​ = 240 V 25 × 1000 ​ = 240 25000 ​ = 104.17 Amperes

Example 2: Three-Phase Transformer Full-Load Current

A 75 kVA , 480 V 480\text{V} 480 V three-phase delta primary to 208 Y / 120 V 208\text{Y}/120\text{V} 208 Y /120 V three-phase four-wire wye secondary transformer: I primary = 75 × 1000 1.73205 × 480 V = 75000 831.38 = 90.21 Amperes I_{\text{primary}} = \frac{75 \times 1000}{1.73205 \times 480\text{ V}} = \frac{75000}{831.38} = \mathbf{90.21\text{ Amperes}} I primary ​ = 1.73205 × 480 V 75 × 1000 ​ = 831.38 75000 ​ = 90.21 Amperes I secondary = 75 × 1000 1.73205 × 208 V = 75000 360.27 = 208.18 Amperes I_{\text{secondary}} = \frac{75 \times 1000}{1.73205 \times 208\text{ V}} = \frac{75000}{360.27} = \mathbf{208.18\text{ Amperes}} I secondary ​ = 1.73205 × 208 V 75 × 1000 ​ = 360.27 75000 ​ = 208.18 Amperes

Standard 3-Phase Transformer Full-Load Current Reference Table:

kVA Rating 480V Primary FLC (Amps) 208V Secondary FLC (Amps) 240V Secondary FLC (Amps) 480V Secondary FLC (Amps)

  • 15 kVA 18.04 A 41.64 A 36.08 A 18.04 A
  • 30 kVA 36.08 A 83.27 A 72.17 A 36.08 A
  • 45 kVA 54.13 A 124.91 A 108.25 A 54.13 A
  • 75 kVA 90.21 A 208.18 A 180.42 A 90.21 A
  • 112.5 kVA 135.32 A 312.28 A 270.63 A 135.32 A
  • 150 kVA 180.42 A 416.37 A 360.84 A 180.42 A
  • 225 kVA 270.63 A 624.55 A 541.27 A 270.63 A
  • 300 kVA 360.84 A 832.74 A 721.69 A 360.84 A
  • 500 kVA 601.41 A 1,387.90 A 1,202.81 A 601.41 A
  • 2. Transformer Overcurrent Protection ≤ 1000 Volts (NEC Table 450.3(B))

NEC Article 450 protects transformer windings from destructive overheating caused by overloads and short circuits. It does not protect the secondary conductors (which must be protected under NEC 240.4 and 240.21). Table 450.3(B) governs transformers operating at 1000 Volts or less, dividing protection into two fundamental methods: Primary-Only Protection and Primary and Secondary Protection . +---------------------------------------------------------------------------------------------------------+

  • | NEC TABLE 450.3(B): TRANSFORMERS OPERATING AT <= 1000 VOLTS |
  • | |
  • | PROTECTION METHOD PRIMARY CURRENT RATING MAX PRIMARY OCPD MAX SECONDARY OCPD |
  • | --------------------- --------------------------- ---------------------- -------------------------- |
  • | Primary Only 9 Amperes or more 125% of FLC (Note 1) None Required |
  • | Protection 2 Amperes to < 9 Amperes 167% of FLC (No Note 1) None Required |
  • | Less than 2 Amperes 300% of FLC (No Note 1) None Required |
  • | --------------------- --------------------------- ---------------------- -------------------------- |
  • | Primary AND Secondary 9 Amperes or more (Primary) 250% of FLC (Note 1) 125% of Sec FLC (Note 1) |
  • | Protection < 9 Amperes (Secondary) 250% of FLC (Note 1) 167% of Sec FLC (No Note 1)|
  • +---------------------------------------------------------------------------------------------------------+

Application of Note 1 (Next Higher Standard Rating Rule):

Note 1 Rule: Where 125% of the transformer rated current does not correspond to a standard rating of a fuse or nonadjustable circuit breaker listed in NEC 240.6 , the next higher standard rating shall be permitted.

Crucial Limitation: Note 1 applies ONLY when the base multiplier is 125% (for currents ≥ 9 A \ge 9\text{A} ≥ 9 A ) or 250% (for primary with secondary protection). Note 1 does NOT apply to the 167% or 300% multipliers. For primary currents between 2A and 9A, the maximum rating is strictly capped at 167% of FLC—you must round down to the nearest standard size that does not exceed 167%.

Standard Overcurrent Protective Device Ratings (NEC 240.6(A)): 15 , 20 , 25 , 30 , 35 , 40 , 45 , 50 , 60 , 70 , 80 , 90 , 100 , 110 , 125 , 150 , 175 , 200 , 225 , 250 , 300 , 350 , 400 , 450 , 500 , 600 , 700 , 800 , 1000 Amperes 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 1000\text{ Amperes} 15 , 20 , 25 , 30 , 35 , 40 , 45 , 50 , 60 , 70 , 80 , 90 , 100 , 110 , 125 , 150 , 175 , 200 , 225 , 250 , 300 , 350 , 400 , 450 , 500 , 600 , 700 , 800 , 1000 Amperes

Detailed Sizing Calculations:

Case 1: Primary-Only Protection (Primary Current ≥ 9A)

A 45 kVA, 480V 3-phase to 208Y/120V transformer with primary-only protection.

Primary FLC: I pri = 45000 / ( 1.732 × 480 ) = 54.13 Amperes I_{\text{pri}} = 45000 / (1.732 \times 480) = 54.13\text{ Amperes} I pri ​ = 45000/ ( 1.732 × 480 ) = 54.13 Amperes .

Sizing Multiplier (Table 450.3(B)): Since I pri ≥ 9 A I_{\text{pri}} \ge 9\text{A} I pri ​ ≥ 9 A , maximum protection is 125 % 125\% 125% .

Calculated Ampacity: 54.13 A × 1.25 = 67.66 Amperes 54.13\text{ A} \times 1.25 = \mathbf{67.66\text{ Amperes}} 54.13 A × 1.25 = 67.66 Amperes .

Application of Note 1: 67.66A is not a standard size in NEC 240.6(A). The next higher standard rating permitted is 70 Amperes .

Case 2: Primary-Only Protection (Primary Current 2A to < 9A)

A 3 kVA, 480V single-phase to 120/240V control transformer with primary-only protection.

Primary FLC: I pri = 3000 / 480 = 6.25 Amperes I_{\text{pri}} = 3000 / 480 = 6.25\text{ Amperes} I pri ​ = 3000/480 = 6.25 Amperes .

Sizing Multiplier: Since 2 A ≤ I pri < 9 A 2\text{A} \le I_{\text{pri}} < 9\text{A} 2 A ≤ I pri ​ < 9 A , maximum protection is 167 % 167\% 167% .

Calculated Limit: 6.25 A × 1.67 = 10.44 Amperes 6.25\text{ A} \times 1.67 = \mathbf{10.44\text{ Amperes}} 6.25 A × 1.67 = 10.44 Amperes .

Standard Size Selection: Note 1 does not apply. You cannot round up to 15A because 15A exceeds 10.44A (167%). Therefore, the maximum standard overcurrent device permitted is 10 Amperes .

Case 3: Primary and Secondary Protection (Primary ≥ 9A, Secondary ≥ 9A)

A 75 kVA, 480V 3-phase to 208Y/120V transformer protected on both primary and secondary.

Primary FLC: I pri = 90.21 Amperes I_{\text{pri}} = 90.21\text{ Amperes} I pri ​ = 90.21 Amperes .

Primary Max Multiplier = 250 % 250\% 250% : 90.21 A × 2.50 = 225.53 Amperes 90.21\text{ A} \times 2.50 = 225.53\text{ Amperes} 90.21 A × 2.50 = 225.53 Amperes .

Under Note 1, round up to next standard size = 250 Amperes .

Secondary FLC: I sec = 208.18 Amperes I_{\text{sec}} = 208.18\text{ Amperes} I sec ​ = 208.18 Amperes .

Secondary Max Multiplier = 125 % 125\% 125% : 208.18 A × 1.25 = 260.23 Amperes 208.18\text{ A} \times 1.25 = 260.23\text{ Amperes} 208.18 A × 1.25 = 260.23 Amperes .

Under Note 1, round up to next standard size = 300 Amperes .

3. Secondary Conductor Protection & Tap Rules (NEC 240.21(C))

A critical principle on the Journeyman exam: Overcurrent protection on the primary side of a transformer does NOT protect the secondary conductors , except in two rare configurations:

Single-phase transformer with a 2-wire (single-voltage) secondary.

Three-phase delta-delta transformer with a 3-wire (single-voltage) secondary.

For all common 3-phase 4-wire ( 208 Y / 120 V 208\text{Y}/120\text{V} 208 Y /120 V , 480 Y / 277 V 480\text{Y}/277\text{V} 480 Y /277 V ) and 1-phase 3-wire ( 120 / 240 V 120/240\text{V} 120/240 V ) transformers, secondary conductors have no overcurrent protection at their supply point and must be installed as transformer secondary taps under NEC 240.21(C) : +---------------------------------------------------------------------------------------------------+

  • | TRANSFORMER SECONDARY TAP RULES (NEC 240.21(C)) |
  • | |
  • | RULE MAX LENGTH MINIMUM CONDUCTOR AMPACITY TERMINATION REQUIREMENT|
  • | ----------------------- ----------- ---------------------------------- -----------------------|
  • | 10-Foot Tap 10 Feet Ampacity >= calculated load AND Must terminate in a |
  • | (NEC 240.21(C)(2)) (3.0 m) Ampacity >= rating of OCPD supplied single OCPD/panelboard.|
  • | Conductors must be in a raceway. No 240.4(B) round-up! |
  • | ----------------------- ----------- ---------------------------------- -----------------------|
  • | 25-Foot Tap 25 Feet Ampacity >= (Primary OCPD rating × Must terminate in a |
  • | (NEC 240.21(C)(6)) (7.5 m) Primary-to-Secondary Voltage Ratio) single OCPD or feeder |
  • | Ampacity >= 1/3 of secondary rating.panelboard. |
  • | ----------------------- ----------- ---------------------------------- -----------------------|
  • | Outside Secondary Taps Unlimited Ampacity protected from physical Must terminate in a |
  • | (NEC 240.21(C)(4)) Length damage, outside of building single disconnect/OCPD.|
  • +---------------------------------------------------------------------------------------------------+

Strict Exam Rule: The "next higher standard rating" rule of NEC 240.4(B) is STRICTLY PROHIBITED for tap conductors. Tap conductor ampacity must equal or exceed the rating of the overcurrent device in which the tap terminates!

4. Transformer Accessibility, Location & Clearances (NEC 450.9 & 450.13)

Transformers generate substantial internal core and coil heat during continuous operation ( I 2 R I^2R I 2 R and eddy-current losses) and present fire/flash hazards if improperly placed. +-----------------------------------------------------------------------------+

  • | PHYSICAL INSTALLATION & VENTILATION RULES |
  • | |
  • | [VENTILATION CLEARANCES (NEC 450.9)] |
  • | - Ventilation openings must NOT be obstructed by walls or equipment. |
  • | - Minimum clearance of SIX INCHES (6 in. / 150 mm) from walls and |
  • | combustible materials unless listed otherwise. |
  • | |
  • | [ACCESSIBILITY (NEC 450.13)] |
  • | - General Rule: Transformers must be READILY ACCESSIBLE (450.13). |
  • | - Open Installations (450.13(A)): Dry-type transformers in the open |
  • | (suspended from ceiling beams) need not be readily accessible. |
  • | - Hollow Spaces (450.13(B)): Dry-type transformers <= 50 kVA and <= 1000V |
  • | are PERMITTED in accessible hollow spaces (e.g. above lay-in ceiling |
  • | tiles) if fire-resistant materials surround them & 450.9 is met. |
  • +-----------------------------------------------------------------------------+

Dry-Type Transformers Installed Indoors (NEC 450.21):

112.5 kVA or Less (450.21(A)): Must have a separation of at least 12 inches (300 mm) from combustible material unless separated by a fire-resistant, heat-insulating barrier, or rated ≤ 600 V \le 600\text{V} ≤ 600 V and completely enclosed except for ventilation openings.

Over 112.5 kVA (450.21(B)): Must be installed in a transformer room of fire-resistant construction having a minimum 1-hour fire rating , unless:

Constructed with Class 155 ∘ C 155^{\circ}\text{C} 15 5 ∘ C or higher insulation materials and separated by at least 6 feet horizontally and 12 feet vertically from combustible material.

Completely enclosed within a noncombustible enclosure with Class 155+ insulation.

Loading diagram... Transformer Overcurrent Protection Decision Tree (NEC Table 450.3(B))