Study guide
9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314)
Oklahoma Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Oklahoma Licensing Laws, Board Rules & Safety
1.1 Oklahoma Electrical License Act & CIB Regulations 1.2 OK Journeyman Exam Format, PSI Logistics & Codebook Navigation 1.3 OSHA Electrical Safety Standards (29 CFR 1926/1910) 1.4 NFPA 70E Electrical Safety in the Workplace & Arc Flash 1.5 Permits, Inspections, Structural Integrity & Job Estimating 1.6 Oklahoma's Adopted 2023 NEC: OUBCC Amendments You Must Know 1.7 OSHA 29 CFR 1926 Job-Site Safety: Sanitation, Signage, Ladders, Scaffolds & Fall Protection
2 Chapter 2: General Electrical Theory & Calculations
2.1 Ohm's Law, Watt's Law & DC Series/Parallel Circuits 2.2 AC Theory, Reactance, Impedance & Power Factor 2.3 Three-Phase Power Systems (Delta & Wye Configurations) 2.4 Electrical Units, Formulas & Conversions 2.5 Cost of Power in a Circuit, Efficiency & Troubleshooting/Test Instruments
3 Chapter 3: General Installation Requirements (NEC Article 110)
3.1 Examination, Identification, Installation & Use of Equipment (110.3) 3.2 Electrical Connections, Terminations & Torque Requirements (110.14) 3.3 Working Space, Clearances & Guarding of Live Parts (110.26 & 110.27) 3.4 Enclosure Types, Markings & Available Fault Current (110.24 & 110.28) 3.5 Installations Over 600 Volts: Article 110 Part III, Article 490 & Medium-Voltage Cable
4 Chapter 4: Branch Circuits & Feeders (NEC Articles 210, 215 & 225)
4.1 Branch Circuit Ratings, Multiwire Branch Circuits & Identification (210.3–210.10) 4.2 Ground-Fault Circuit-Interrupter (GFCI) Protection (210.8) 4.3 Arc-Fault Circuit-Interrupter (AFCI) Protection & Receptacle Outlets (210.12 & 210.52) 4.4 Outside Branch Circuits and Feeders (Article 225) & Feeder Sizing (Article 215)
5 Chapter 5: Services & Service Equipment (NEC Article 230)
5.1 Service Clearances, Overhead & Underground Service-Drop Requirements (230.9, 230.24 & 230.30) 5.2 Service-Entrance Conductors, Sizing & Installation (230.40–230.54) 5.3 Service Equipment Disconnecting Means, Overcurrent Protection & Emergency Disconnects (230.70–230.95)
6 Chapter 6: Electrical Load Calculations (NEC Article 220)
6.1 General Lighting, Small Appliance & Laundry Loads (NEC 220.41, 220.42, 220.45 & 220.52) 6.2 Standard Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part III) 6.3 Optional Dwelling Unit Feeder & Service Calculations (NEC Article 220 Part IV) 6.4 Commercial & Multi-Family Load Calculations (Cooktops, Dryers, HVAC & Stores)
7 Chapter 7: Overcurrent Protection & Tap Rules (NEC Article 240)
7.1 Overcurrent Protection Fundamentals & Standard Ampere Ratings (240.4 & 240.6) 7.2 Feeder & Branch Circuit Tap Rules (NEC 240.21) 7.3 Ground-Fault Protection of Equipment & Selective Coordination (NEC 240.13, 240.86 & Article 245)
8 Chapter 8: Grounding and Bonding (NEC Article 250)
8.1 General Grounding Principles, System Grounding & Grounded Conductors (NEC 250.4, 250.20 & 250.24) 8.2 Grounding Electrode System & Grounding Electrode Conductor (GEC) Sizing (NEC 250.50, 250.52 & 250.66) 8.3 Equipment Grounding Conductors (EGC) Sizing & Installation (NEC 250.118, 250.120 & 250.122) 8.4 Bonding Requirements, Main/System Bonding Jumpers & Separately Derived Systems (NEC 250.28, 250.30 & 250.102)
9 Chapter 9: Wiring Methods & Materials (NEC Articles 300–314)
9.1 General Requirements for Wiring Methods, Underground Clearances & Firestopping (NEC Article 300) 9.2 Conductor Ampacity Ratings, Temperature Correction & Bundling Adjustments (Article 310 & Table 310.16) 9.3 Nonmetallic-Sheathed Cable (Type NM), Metal-Clad Cable (Type MC) & Armored Cable (Type AC) 9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314) 9.5 Temporary Installations (Article 590), Cranes & Hoists (Article 610), Elevators & Escalators (Article 620)
10 Chapter 10: Raceways, Tubing, Conduit Fill & Underground Systems
10.1 Rigid Metal Conduit (RMC), Intermediate Metal Conduit (IMC) & Electrical Metallic Tubing (EMT) 10.2 Nonmetallic Raceways (PVC, RTRC, Liquidtight) & Cable Trays (NEC Articles 352, 356, 392) 10.3 Conduit Fill Calculations (Chapter 9 Tables 1, 4 & 5, Annex C) & Pull Box Sizing (NEC 314.28)
11 Chapter 11: Motors, Controllers & Air Conditioning (NEC Articles 430 & 440)
11.1 Motor Full-Load Current (FLC), Branch Circuit Conductor Sizing & Disconnects (430.6, 430.22 & 430.102) 11.2 Motor Overload Protection & Motor Branch Circuit Short-Circuit/Ground-Fault Protection (430.32 & 430.52) 11.3 Motor Feeder Conductor Sizing & Feeder Overcurrent Protection (430.24 & 430.62) 11.4 Air Conditioning & Refrigeration Equipment (NEC Article 440: MCA, MOCP & Disconnects)
12 Chapter 12: Transformers & Equipment (NEC Articles 450, 410, 422 & 424)
12.1 Transformer Sizing, Protection & Voltage Calculations (NEC Article 450 & Table 450.3(B)) 12.2 Luminaires, Lampholders & Lamps Installation (NEC Article 410) 12.3 Appliances & Electric Water Heaters (NEC Article 422) 12.4 Fixed Electric Space-Heating Equipment (NEC Article 424) 12.5 Snow-Melting & De-Icing Equipment (Article 426) and Pipeline & Vessel Heating (Article 427) 12.6 Electric Signs & Outline Lighting (Article 600) and Lighting Systems 30 Volts or Less (Article 411)
13 Chapter 13: Special Occupancies & Hazardous Locations (NEC Articles 500–517)
13.1 Hazardous (Classified) Locations: Class I, II, and III (Articles 500, 501, 502 & 503) 13.2 Commercial Garages, Repair Facilities & Fuel Dispensing Facilities (Articles 511 & 514) 13.3 Health Care Facilities: Patient Care Spaces & Wiring Methods (Article 517) 13.4 Agricultural Buildings & Manufactured/Mobile Homes (Articles 547 & 550) 13.5 Bulk Storage Plants (Article 515) and Spray Application, Dipping & Coating (Article 516)
14 Chapter 14: Special Equipment, Swimming Pools & Low-Voltage Systems
14.1 Swimming Pools, Spas, Hot Tubs & Hydromassage Bathtubs (Article 680) 14.2 Emergency Systems, Legally Required & Optional Standby Systems (Articles 700, 701 & 702) 14.3 Class 1, 2, 3 & Class 4 Power-Limited Circuits (NEC Articles 722, 724, 725 & 726) and Fire Alarms (NEC Article 760) 14.4 RV Parks (Article 551), Floating Buildings (Article 553) & Marinas/Docking Facilities (Article 555)
9.4 Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314)
Key Takeaways Explain This Topic AI
NEC Table 314.16(A) establishes standard cubic-inch capacities for metal boxes, while Table 314.16(B) defines volume allowances per conductor size (#18 = 1.50, #16 = 1.75, #14 = 2.00, #12 = 2.25, #10 = 2.50, #8 = 3.00, #6 = 5.00 cu in).
Box volume allowances under NEC 314.16(B) require counting: 1 allowance per circuit conductor entering/spliced; 1 allowance for internal cable clamps (based on largest conductor); 1 allowance for fixture studs/hickeys; 2 allowances for each single-gang device strap/yoke (based on largest conductor connected to the device); and 1 allowance for up to 4 EGCs plus 1/4 allowance for each additional EGC.
Pigtails and jumpers that originate and remain entirely within the box count as ZERO (0) volume allowance (NEC 314.16(B)(1)).
For straight pull boxes containing conductors 4 AWG and larger under NEC 314.28(A)(1), the length of the box must not be less than 8 times the trade diameter of the largest raceway entering the box.
For angle pulls, U-pulls, or splices under NEC 314.28(A)(2), the distance between each raceway entry and the opposite wall must be at least 6 times the trade size of the largest raceway plus the sum of diameters of all other raceway entries on the same wall.
Last updated: August 2026
Outlet, Device, Pull & Junction Boxes Sizing and Box Fill Calculations (NEC Article 314)
Outlet boxes, device boxes, pull boxes, and junction boxes must provide sufficient internal cubic-inch volume to house conductors, splices, internal clamps, and wiring devices without crowding. Overcrowding electrical boxes causes conductor insulation damage during device installation, creates dangerous hot spots due to restricted heat dissipation, and increases the risk of ground faults and short circuits. On the Oklahoma Journeyman Electrician examination, box fill calculations and pull box sizing represent some of the most heavily tested numerical problems.
1. Standard Metal Box Volumes (NEC Table 314.16(A))
NEC Table 314.16(A) lists the standard trade dimensions and minimum cubic-inch capacities for commonly manufactured metal boxes. +-----------------------------------------------------------------------------+
- | STANDARD METAL BOX CAPACITIES (TABLE 314.16(A)) |
- | |
- | Box Dimensions (Trade Size) Minimum Volume Capacity |
- | ------------------------------------------ ----------------------- |
- | 4" x 1-1/4" Round / Octagonal 12.5 cu in |
- | 4" x 1-1/2" Round / Octagonal 15.5 cu in |
- | 4" x 2-1/8" Round / Octagonal 21.5 cu in |
- | 4" x 1-1/4" Square (4-Square Shallow) 18.0 cu in |
- | 4" x 1-1/2" Square (Standard 1900 Box) 21.0 cu in |
- | 4" x 2-1/8" Square (Deep 4-Square Box) 30.3 cu in |
- | 4-11/16" x 1-1/2" Square 29.5 cu in |
- | 4-11/16" x 2-1/8" Square (Deep Jumbo) 42.0 cu in |
- | 3" x 2" x 2" Standard Device Box 10.0 cu in |
- | 3" x 2" x 2-1/2" Device Box 12.5 cu in |
- | 3" x 2" x 3-1/2" Deep Device Box 18.0 cu in |
- | 4" x 2-1/8" x 1-7/8" Handy Box 13.0 cu in |
- +-----------------------------------------------------------------------------+
Nonmetallic Boxes and Plaster Rings (Mud Rings):
Nonmetallic Boxes (Plastic / Fiberglass): The volume must be durably and legibly marked in cubic inches on the interior of the box by the manufacturer (NEC 314.16(A)(2)).
Plaster Rings / Extension Rings (NEC 314.16(A)): Raised plaster rings (mud rings) marked with their volume in cubic inches add their marked capacity to the total box volume (e.g., a 4-square box of 21.0 cu in + a single-gang 1/2" raised plaster ring of 3.5 cu in = 24.5 total cu in).
2. Conductor Volume Allowances (NEC Table 314.16(B))
NEC Table 314.16(B) assigns a specific volume allowance in cubic inches for each conductor size entering or contained in a box: +-----------------------------------------------------------------------------+
- | VOLUME ALLOWANCE PER CONDUCTOR (NEC TABLE 314.16(B)) |
- | |
- | Conductor Size (AWG) Volume Allowance per Conductor |
- | -------------------- ------------------------------ |
- | 18 AWG 1.50 cubic inches |
- | 16 AWG 1.75 cubic inches |
- | 14 AWG 2.00 cubic inches |
- | 12 AWG 2.25 cubic inches |
- | 10 AWG 2.50 cubic inches |
- | 8 AWG 3.00 cubic inches |
- | 6 AWG 5.00 cubic inches |
- +-----------------------------------------------------------------------------+
- 3. Box Volume Allowance Rules (NEC 314.16(B)(1)–(5))
To determine the total volume required for an enclosure, count the individual volume allowances based on the following five rules: +-----------------------------------------------------------------------------+
- | THE FIVE BOX FILL COUNTING RULES (NEC 314.16(B)) |
- | |
- | 1. Conductor Fill (314.16(B)(1)): |
- | - 1 volume allowance for EACH conductor originating outside and |
- | terminating or spliced inside the box. |
- | - 1 volume allowance for EACH unbroken conductor passing through. |
- | - ZERO (0) for pigtails/jumpers originating and remaining inside box! |
- | |
- | 2. Internal Clamp Fill (314.16(B)(2)): |
- | - 1 volume allowance total (based on LARGEST conductor in the box), |
- | regardless of whether there are 1, 2, or 4 internal clamps. |
- | - External conduit connectors / cable clamps count as ZERO (0). |
- | |
- | 3. Support Fittings Fill (314.16(B)(3)): |
- | - 1 volume allowance for EACH fixture stud or hickey present (largest). |
- | |
- | 4. Device or Equipment Fill (314.16(B)(4)): |
- | - 2 volume allowances (DOUBLE VOLUME) for each single-gang strap/yoke |
- | (duplex receptacle, GFCI, switch) based on LARGEST conductor |
- | connected to that device. (4 allowances for double-gang yokes). |
- | |
- | 5. Equipment Grounding Conductor (EGC) Fill (314.16(B)(5)): |
- | - 1 volume allowance (based on largest EGC) for up to 4 EGCs. |
- | - PLUS 1/4 (0.25) volume allowance for EACH additional EGC beyond 4. |
- | - PLUS 1 volume allowance for an isolated grounding conductor set. |
- +-----------------------------------------------------------------------------+
- 4. Comprehensive Worked Box Fill Calculations
- Scenario 1: Sizing an Outlet Box with Mixed Conductors and Devices
An electrical box contains:
Two (2) 12/2 Type NM-B cables with ground entering through internal clamps.
One (1) 12/3 Type NM-B cable with ground entering through internal clamps.
One (1) duplex receptacle connected to #12 AWG conductors.
Three (3) #12 AWG pigtails spliced inside the box connecting to the receptacle. +-----------------------------------------------------------------------------+
- | STEP-BY-STEP BOX FILL CALCULATION (SCENARIO 1) |
- | |
- | Step 1: Count Conductor Fill (314.16(B)(1)) |
- | - From two 12/2 cables: 2 black + 2 white = 4 conductors |
- | - From one 12/3 cable: 1 black + 1 red + 1 white = 3 conductors |
- | - Pigtails originating inside box: 0 conductors |
- | Total Conductor Count = 7 conductors x 2.25 cu in = 15.75 cu in |
- | |
- | Step 2: Count Internal Clamps (314.16(B)(2)) |
- | - Internal clamps present: Count 1 allowance (largest conductor) |
- | Total Clamp Count = 1 allowance x 2.25 cu in = 2.25 cu in |
- | |
- | Step 3: Count Support Fittings (314.16(B)(3)) |
- | - No fixture studs or hickeys present = 0.00 cu in |
- | |
- | Step 4: Count Device Strap Fill (314.16(B)(4)) |
- | - One single-gang duplex receptacle: Count 2 allowances |
- | Total Device Count = 2 allowances x 2.25 cu in = 4.50 cu in |
- | |
- | Step 5: Count Equipment Grounding Conductors (314.16(B)(5)) |
- | - Total bare grounds entering: 2 + 1 = 3 EGCs (≤ 4 EGCs) |
- | - Count 1 allowance based on largest EGC (#12 AWG) |
- | Total Ground Count = 1 allowance x 2.25 cu in = 2.25 cu in |
- | |
- | Step 6: Total Required Box Volume |
- | Total Volume = 15.75 + 2.25 + 0 + 4.50 + 2.25 = 24.75 cu in |
- | |
- | Step 7: Select Appropriate Box from Table 314.16(A) |
- | - 4" x 1-1/2" Square Box (21.0 cu in) is TOO SMALL! |
- | - 4" x 2-1/8" Square Box (30.3 cu in) is COMPLIANT (30.3 ≥ 24.75) |
- | - OR 4" x 1-1/2" Box (21.0 cu in) + 1/2" Mud Ring (5.0 cu in) |
- | Total Volume = 26.0 cu in (COMPLIANT: 26.0 ≥ 24.75 cu in) |
- +-----------------------------------------------------------------------------+
- Scenario 2: Calculating More Than 4 Equipment Grounding Conductors
Where six (6) #14 AWG equipment grounding conductors enter a junction box:
First 4 EGCs = 1.00 allowance × 2.00 cu in = 2.00 cu in 1.00 \text{ allowance} \times 2.00\text{ cu in} = 2.00\text{ cu in} 1.00 allowance × 2.00 cu in = 2.00 cu in
Remaining 2 EGCs = 2 × 0.25 allowance = 0.50 allowance × 2.00 cu in = 1.00 cu in 2 \times 0.25 \text{ allowance} = 0.50 \text{ allowance} \times 2.00\text{ cu in} = 1.00\text{ cu in} 2 × 0.25 allowance = 0.50 allowance × 2.00 cu in = 1.00 cu in
Total EGC Volume = 2.00 + 1.00 = 3.00 cu in 2.00 + 1.00 = 3.00\text{ cu in} 2.00 + 1.00 = 3.00 cu in (equal to 1.50 allowances 1.50 \text{ allowances} 1.50 allowances ).
5. Pull & Junction Box Sizing for 4 AWG and Larger (NEC 314.28)
Boxes and conduit bodies containing conductors of 4 AWG or larger under system voltages up to 1,000 volts must be sized based on raceway trade sizes to ensure large stiff conductors can be pulled without damaging the insulation or exceeding minimum wire bending radii. +-----------------------------------------------------------------------------+
- | PULL & JUNCTION BOX SIZING RULES (NEC 314.28) |
- | |
- | [STRAIGHT PULLS (NEC 314.28(A)(1))] |
- | - Box length shall not be less than EIGHT TIMES (8x) the trade diameter |
- | of the largest raceway entering the box. |
- | |
- | $$\text{Length}_{\text{Straight}} \ge 8 \times \text{Trade Size of Largest Raceway}$$
- | |
- | [ANGLE PULLS, U-PULLS & SPLICES (NEC 314.28(A)(2))] |
- | - Distance between each raceway entry and opposite wall shall not be |
- | less than SIX TIMES (6x) the largest raceway trade size PLUS the sum |
- | of the diameters of all other raceway entries on the same wall. |
- | |
| $$\text{Distance}_{\text{Angle}} \ge (6 \times \text{Largest Raceway}) + \sum (\text{All Other Raceways on Same Wall})$$
- | |
- | [DISTANCE BETWEEN RACEWAYS ENCLOSING SAME CONDUCTOR] |
- | - Distance between raceway entry and exit for the same circuit shall |
- | not be less than SIX TIMES (6x) the raceway trade size. |
- +-----------------------------------------------------------------------------+
- Worked Example: Sizing an Angle Pull Box
An angle pull junction box has the following conduits entering on one side wall containing 4/0 AWG conductors:
- One (1) 4-inch conduit
- Two (2) 4-inch conduits +-----------------------------------------------------------------------------+
- | STEP-BY-STEP ANGLE PULL BOX SIZING |
- | |
- | Formula: Min Distance = (6 x Largest Conduit) + Sum of Other Conduits |
- | |
- | Step 1: Multiply Largest Raceway by 6 |
- | 6 x 4 inches = 24 inches |
- | |
- | Step 2: Add Diameters of All Other Raceways on That Wall |
- | 4 inches + 4 inches = 8 inches |
- | |
- | Step 3: Calculate Minimum Interior Dimension |
- | Minimum Width / Length = 24 inches + 8 inches = 32 inches |
- | |
- | Step 4: Calculate Minimum Distance Between Raceway Entry & Exit Ports |
- | Distance = 6 x 4 inches = 24 inches minimum separation |
- +-----------------------------------------------------------------------------+