Study guide
6.4 Electrical Components & Equipment Identification
Oklahoma Fire Alarm Installer License Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Oklahoma Licensing Laws & Administrative Authority
1.1 Oklahoma Alarm, Locksmith, and Fire Sprinkler Industry Act (59 O.S. § 1800) 1.2 Regulatory Authority of the Oklahoma Department of Labor (ODOL) 1.3 Alarm, Locksmith, and Fire Sprinkler Industry Committee 1.4 Exam Format, Fees & the ODOL Licensing Path (Assessment 4011)
2 License Classes, Trainee Supervision & Company Rules
2.1 Licensing Classifications — Company, Manager, Technician, Salesperson 2.2 Trainee Licensing, 15-Day Application Window & OSBI Background Checks 2.3 Trainee Direct Supervision & 3:1 Job Site Ratio Limits
3 ODOL Operational Compliance, Renewals & Enforcement
3.1 Vehicle Identification Standards & Pocket License Display 3.2 Annual License Renewal Schedule, Grace Periods & Fees 3.3 Violations, Unlawful Practices, Misdemeanors & Administrative Fines 3.4 Oklahoma Commercial Fire Alarm Tagging (OAC 380:75-5-1) 3.5 Alarm Contracts, Consumer Disclosures & Contract Law Basics
4 Fire Alarm Codes, Standards & Building Life Safety
4.1 NFPA 72 National Fire Alarm and Signaling Code Overview 4.2 IBC Chapter 9 & NFPA 101 Occupancy Requirements 4.3 Dedicated Function Systems & Emergency Control Interfaces
5 NEC Article 760 & Wiring Methods
5.1 Power-Limited vs. Non-Power-Limited Fire Alarm Circuits 5.2 Fire Alarm Cable Ratings, Markings & Substitution Hierarchy 5.3 Wiring Installation Methods, Raceways & 2-Inch Physical Separation
6 Electrical Fundamentals & Fire Alarm Calculations
6.1 Ohm's Law, Power Law & DC Circuit Analysis 6.2 Secondary Power & Battery Standby Calculations with 20% Derating 6.3 Voltage Drop Calculations on Notification Appliance Circuits 6.4 Electrical Components & Equipment Identification 6.5 Grounding, Bonding & Ground Loops (NEC Articles 90, 110, 250)
7 Circuit Pathways, Classes & Fault Troubleshooting
7.1 NFPA 72 Circuit Classifications — Class A, Class B, Class X, Class N 7.2 End-of-Line Resistors & Circuit Supervision 7.3 Multimeter Diagnostics, Ground Faults & Circuit Troubleshooting
8 Initiating Devices — Smoke & Heat Detection
8.1 Smoke Detection Technologies — Photoelectric, Ionization & Air Sampling 8.2 Smoke Detector Spacing, Ceilings & Environmental Factors 8.3 Heat Detectors — Fixed Temperature & Rate-of-Rise Principles
9 Specialty Initiating Devices & Sprinkler Monitoring
9.1 Duct Smoke Detectors, Sampling Tubes & Airflow Velocity 9.2 Manual Fire Alarm Boxes & Pull Station Requirements 9.3 Waterflow Switches & Sprinkler Supervisory Devices
10 Notification Appliances & Emergency Communications
10.1 Audible Notification Requirements, dBA Levels & 520 Hz Low-Frequency Sounders 10.2 Visual Notification Appliances, Strobe Candela & Synchronization 10.3 Supervising Station Alarm Systems & Communication Methods
11 FACU Hardware, Addressable Modules & Installation
11.1 Fire Alarm Control Units (FACU) & Dedicated Branch Circuits 11.2 Addressable Modules — Monitor, Control, Relay & Fault Isolators 11.3 Firestopping Systems & Cable Penetrations through Rated Barriers 11.4 Manufacturer Specifications, Equipment Listings & Field Compatibility 11.5 Project Plans, Blueprints & Specifications
12 Commissioning, Periodic ITM, Impairments & Job Safety
12.1 System Commissioning, Acceptance Testing & Records of Completion 12.2 Periodic Inspection, Testing, and Maintenance (NFPA 72 Table 14.4.3.2) 12.3 Impairment Handling, Deficiency Tags & Fire Watch Protocols 12.4 OSHA Job-Site Safety — Fall Protection, Ladder Rules & Electrical PPE 12.5 Hand Tools, Power Tools & Job-Site Equipment 12.6 Job-Site Injuries, Health Conditions & First-Aid Response
6.4 Electrical Components & Equipment Identification
Key Takeaways Explain This Topic AI
Batteries in series add voltage while batteries in parallel add ampere-hour capacity: two 12 V 18 Ah units in series give 24 V at 18 Ah.
Transformers are rated in volt-amperes, so a 40 VA 24 VAC transformer delivers roughly 1.67 amperes.
Form C relay contacts are single-pole double-throw and drive elevator recall, HVAC shutdown, and damper control interfaces.
A multimeter measures voltage in parallel and current in series on an energized circuit, but resistance only on a de-energized circuit.
The fire alarm branch-circuit breaker must be marked in red, identified as FIRE ALARM CIRCUIT, and mechanically locked in the ON position.
Last updated: September 2026
6.4 Electrical Components & Equipment Identification
Duty B of the Oklahoma technician blueprint — Basic Electronics and Electrical Components — is 20% of the exam, roughly 14 of 70 questions , and its very first task is to "identify and describe the operation of electrical components and equipment." That is a recognition-and-function exam objective: given a component, state what it does and where it appears in a fire alarm system.
Resistors
A resistor opposes current flow and dissipates the resulting energy as heat. In fire alarm work the dominant application is the end-of-line resistor (EOLR) , which lets the control unit distinguish a normal circuit from an open or a short.
Resistance is measured in ohms (Ω); common fire alarm EOLR values are 2.2 kΩ, 3.3 kΩ, 4.7 kΩ, 10 kΩ, and 47 kΩ, dictated by the panel manufacturer, never by the installer's preference.
Power rating matters: a resistor must be rated above the wattage it will dissipate (P = V²/R). A ½-watt EOLR on a 24 VDC circuit at 2.2 kΩ dissipates about 0.26 W, giving roughly a 2:1 safety margin.
Color bands encode the value: the first two bands are significant digits, the third is the multiplier, and the fourth is tolerance (gold = ±5%, silver = ±10%). Red-red-red-gold reads 2-2 × 100 = 2.2 kΩ ±5%.
Transformers
A transformer transfers energy between circuits by magnetic induction and changes voltage in the process. It works on alternating current only.
A fire alarm control unit's step-down transformer converts 120 VAC branch-circuit power to a lower AC voltage (commonly 16–24 VAC) for the panel's power supply.
Turns ratio sets the voltage ratio: a 5:1 step-down transformer fed 120 VAC delivers 24 VAC.
Transformers are sized in volt-amperes (VA) , not watts. A 40 VA, 24 VAC transformer can deliver roughly 1.67 A (40 ÷ 24).
Batteries
Fire alarm secondary power uses sealed lead-acid (SLA) / valve-regulated (VRLA) batteries.
A 12 V SLA battery is nominally 12 volts; two in series produce the 24 VDC that commercial panels require. Series connection adds voltage ; parallel connection adds capacity (Ah) at the same voltage.
Ampere-hour (Ah) is the capacity rating — a 18 Ah battery theoretically supplies 1 A for 18 hours.
Panels float charge the batteries continuously and supervise them for presence, low voltage, and open charging circuit.
Relays and Contacts
A relay is an electrically operated switch: energizing a coil moves an armature that opens or closes a separate set of contacts, allowing a low-power fire alarm circuit to control a high-power load.
- Contact Designation State When Coil Is De-Energized Typical Fire Alarm Use
- Normally Open (NO) / Form A Open Waterflow switch, most initiating devices
- Normally Closed (NC) / Form B Closed Door holders, fail-safe interfaces, supervised inputs
- Form C (SPDT) One contact closed, one open, common pole Elevator recall, HVAC shutdown, damper control
Initiating devices report by contact action : a pull station or heat detector closes a normally-open contact across the circuit, shunting the EOLR and producing the alarm current the panel is watching for.
Connectors, Terminations, and Splicing Tools
Terminal blocks are the preferred termination inside panels and back boxes — screw pressure on a stripped conductor or on a fork/ring lug.
Crimp connectors (butt splices, lugs, ferrules) require the matched crimping tool; pliers produce a high-resistance joint that fails megger testing.
Wire nuts / twist-on connectors and insulation-displacement B-connectors are used for field splices where permitted, always inside a listed enclosure.
Tools of the trade: wire strippers gauged to the conductor, crimpers , cable cutters , and a punch-down tool for telecom-style blocks. Nicking a conductor while stripping creates a stress riser that snaps under vibration months later.
Fuses, Circuit Breakers, and Surge Protectors
A fuse is a one-time overcurrent device: a metal element melts and must be replaced. Fire alarm panels use them on NAC outputs and auxiliary power taps.
A circuit breaker is a resettable overcurrent device. The fire alarm branch circuit breaker must be marked in red, identified as "FIRE ALARM CIRCUIT," and mechanically locked in the ON position .
A surge protective device (SPD) clamps transient overvoltage from lightning or utility switching, diverting it to ground. SPDs are rated by UL 1449 and are essential in Oklahoma, which sits in one of the most lightning-active regions in the United States.
The Multimeter
A digital multimeter (DMM) is the technician's primary instrument. Its three core functions map to Ohm's Law:
- Function Meter Connection Circuit State
- Voltage (V) Parallel across the two points Circuit energized
- Current (A) Series , meter inserted into the path Circuit energized
- Resistance (Ω) Across the component Circuit de-energized
Warning
Measuring resistance on an energized circuit gives a meaningless reading and can destroy the meter; placing a meter set to amps in parallel across a source creates a dead short through the meter's shunt.
Exam Watchouts
Important
Series adds volts, parallel adds amp-hours. Two 12 V 18 Ah batteries in series give 24 V at 18 Ah — not 36 Ah. The most common battery question on the exam depends on that single distinction.
Tip
Transformers are rated in VA , batteries in Ah , resistors in Ω and watts . Matching the component to its unit of measure answers a surprising number of Duty B items outright.