Study guide
11.5 Project Plans, Blueprints & Specifications
Oklahoma Fire Alarm Installer License Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Oklahoma Licensing Laws & Administrative Authority
1.1 Oklahoma Alarm, Locksmith, and Fire Sprinkler Industry Act (59 O.S. § 1800) 1.2 Regulatory Authority of the Oklahoma Department of Labor (ODOL) 1.3 Alarm, Locksmith, and Fire Sprinkler Industry Committee 1.4 Exam Format, Fees & the ODOL Licensing Path (Assessment 4011)
2 License Classes, Trainee Supervision & Company Rules
2.1 Licensing Classifications — Company, Manager, Technician, Salesperson 2.2 Trainee Licensing, 15-Day Application Window & OSBI Background Checks 2.3 Trainee Direct Supervision & 3:1 Job Site Ratio Limits
3 ODOL Operational Compliance, Renewals & Enforcement
3.1 Vehicle Identification Standards & Pocket License Display 3.2 Annual License Renewal Schedule, Grace Periods & Fees 3.3 Violations, Unlawful Practices, Misdemeanors & Administrative Fines 3.4 Oklahoma Commercial Fire Alarm Tagging (OAC 380:75-5-1) 3.5 Alarm Contracts, Consumer Disclosures & Contract Law Basics
4 Fire Alarm Codes, Standards & Building Life Safety
4.1 NFPA 72 National Fire Alarm and Signaling Code Overview 4.2 IBC Chapter 9 & NFPA 101 Occupancy Requirements 4.3 Dedicated Function Systems & Emergency Control Interfaces
5 NEC Article 760 & Wiring Methods
5.1 Power-Limited vs. Non-Power-Limited Fire Alarm Circuits 5.2 Fire Alarm Cable Ratings, Markings & Substitution Hierarchy 5.3 Wiring Installation Methods, Raceways & 2-Inch Physical Separation
6 Electrical Fundamentals & Fire Alarm Calculations
6.1 Ohm's Law, Power Law & DC Circuit Analysis 6.2 Secondary Power & Battery Standby Calculations with 20% Derating 6.3 Voltage Drop Calculations on Notification Appliance Circuits 6.4 Electrical Components & Equipment Identification 6.5 Grounding, Bonding & Ground Loops (NEC Articles 90, 110, 250)
7 Circuit Pathways, Classes & Fault Troubleshooting
7.1 NFPA 72 Circuit Classifications — Class A, Class B, Class X, Class N 7.2 End-of-Line Resistors & Circuit Supervision 7.3 Multimeter Diagnostics, Ground Faults & Circuit Troubleshooting
8 Initiating Devices — Smoke & Heat Detection
8.1 Smoke Detection Technologies — Photoelectric, Ionization & Air Sampling 8.2 Smoke Detector Spacing, Ceilings & Environmental Factors 8.3 Heat Detectors — Fixed Temperature & Rate-of-Rise Principles
9 Specialty Initiating Devices & Sprinkler Monitoring
9.1 Duct Smoke Detectors, Sampling Tubes & Airflow Velocity 9.2 Manual Fire Alarm Boxes & Pull Station Requirements 9.3 Waterflow Switches & Sprinkler Supervisory Devices
10 Notification Appliances & Emergency Communications
10.1 Audible Notification Requirements, dBA Levels & 520 Hz Low-Frequency Sounders 10.2 Visual Notification Appliances, Strobe Candela & Synchronization 10.3 Supervising Station Alarm Systems & Communication Methods
11 FACU Hardware, Addressable Modules & Installation
11.1 Fire Alarm Control Units (FACU) & Dedicated Branch Circuits 11.2 Addressable Modules — Monitor, Control, Relay & Fault Isolators 11.3 Firestopping Systems & Cable Penetrations through Rated Barriers 11.4 Manufacturer Specifications, Equipment Listings & Field Compatibility 11.5 Project Plans, Blueprints & Specifications
12 Commissioning, Periodic ITM, Impairments & Job Safety
12.1 System Commissioning, Acceptance Testing & Records of Completion 12.2 Periodic Inspection, Testing, and Maintenance (NFPA 72 Table 14.4.3.2) 12.3 Impairment Handling, Deficiency Tags & Fire Watch Protocols 12.4 OSHA Job-Site Safety — Fall Protection, Ladder Rules & Electrical PPE 12.5 Hand Tools, Power Tools & Job-Site Equipment 12.6 Job-Site Injuries, Health Conditions & First-Aid Response
11.5 Project Plans, Blueprints & Specifications
Key Takeaways Explain This Topic AI
Written dimensions on a drawing always govern over dimensions obtained by scaling.
On a 1/8 inch = 1 foot-0 inches drawing, one inch of paper represents eight feet of building.
Fire alarm specifications are written under CSI MasterFormat Division 28, Section 28 31 00, Fire Detection and Alarm.
The riser diagram is schematic and not to scale, so conductor lengths for voltage-drop calculations come from plan views and vertical rise.
OAC 380:75-1-3 incorporates the IBC, NFPA 70, NFPA 72, and NFPA 101 as minimum standards, and the more stringent standard applies when they conflict.
Last updated: September 2026
11.5 Project Plans, Blueprints & Specifications
Duty F is the heaviest block on the Oklahoma technician exam at 24% — roughly 17 of 70 questions — and its first two tasks are reading project plans to determine dimensions and installation requirements, and demonstrating adherence to specifications. Everything downstream (material type, elevation, device location) is read off paper before a single anchor is set.
Anatomy of a Construction Drawing Set
Commercial drawing sets are organized by discipline, and the sheet prefix tells you which one you are holding.
- Prefix Discipline Why the Fire Alarm Tech Opens It
- A Architectural Room names/numbers, wall types, ceiling heights, door swings
- S Structural Beams, joists, and slab depths that dictate anchor selection
- M Mechanical Duct sizes and air handler capacity — where duct detectors go
- E Electrical Panel schedules, branch circuits, the dedicated fire alarm circuit
- FA / FP Fire Alarm / Fire Protection Device layout, riser diagram, matrix of operations
- RCP Reflected Ceiling Plan Grid layout, diffusers, and lights that conflict with detector spacing
Every sheet carries a title block (project, sheet name and number, date, seal) and a revision block . Changes are marked with a revision cloud and a numbered delta triangle. Working from a superseded sheet is the single most expensive mistake on a commercial job — always verify the revision number against the current issue log.
Reading Scale
Fire alarm plans are typically drawn at 1/8 inch = 1 foot-0 inches for building plans and 1/4 inch = 1 foot-0 inches for enlarged areas.
Worked example. On a 1/8" = 1'-0" sheet, one inch of paper equals eight feet of building. A corridor that measures 3½ inches on the drawing is 3.5 × 8 = 28 feet long. If NFPA 72 permits smoke detectors on 30-foot centers in that corridor, one detector centered in the run covers it; a second would be added only if the corridor continues past the 15-foot half-spacing from the end wall.
Use an architect's scale , not a tape measure on paper, and never scale a dimension that is written on the drawing — written dimensions always govern over scaled measurements.
Views, Symbols, and the Riser Diagram
Plan view looks straight down; it fixes horizontal device location.
Elevation view looks at a vertical face; it fixes mounting heights — pull stations with the operable part 42 to 48 inches above the finished floor, and wall-mounted visible appliances with the entire lens between 80 and 96 inches above the floor.
Section view cuts through the building to show construction layers, beam pockets, and plenum depth.
The symbol legend on the FA cover sheet decodes every device glyph. Symbols are project-specific — do not assume the triangle means the same thing it did on the last job.
The riser diagram is a schematic, not a scaled drawing. It shows the vertical distribution of circuits: how many SLC loops and NACs leave the FACU, which floors they serve, conductor counts and gauges, and where booster panels sit.
The matrix of operations (input/output matrix) is a grid of every initiating device against every output function. It is the authoritative statement of what the system does and becomes the acceptance test script.
Specifications and the Order of Precedence
Written specifications are organized by CSI MasterFormat . Fire alarm work lives in Division 28 — Electronic Safety and Security , typically Section 28 31 00, Fire Detection and Alarm . The specification states manufacturer basis-of-design, acceptable substitutions, wire types, warranty length, testing requirements, and closeout documents.
When paper disagrees with paper, the contract documents state the precedence; the common commercial order is:
- Addenda and change orders (most recent governs)
- Specifications
- Drawings
- Shop drawings and submittals
And above all of it: the adopted code and the AHJ . A specification cannot authorize something the code forbids. In Oklahoma, OAC 380:75-1-3 incorporates the IBC, NFPA 70, NFPA 72, and NFPA 101 as minimum installation standards, and where those conflict, the more stringent standard applies .
- The Submittal Cycle Contract Drawings → SHOP DRAWINGS / SUBMITTALS → Engineer & AHJ review
- ↑ │
- │ ▼
- ADDENDA / RFI ←──────── field questions ──────── APPROVED FOR CONSTRUCTION
- │
- ▼
- AS-BUILT DRAWINGS
Shop drawings are the contractor's engineered layout: battery standby calculations, voltage-drop calculations, equipment cut sheets, device counts, and point-to-point wiring. Oklahoma AHJs typically require this package before permit issuance.
An RFI (request for information) is the formal way to resolve an ambiguity. Verbal answers from a superintendent do not change a contract document.
An addendum changes the documents before bid; a change order changes them after contract award, and it adjusts price and schedule.
As-built (record) drawings mark every field deviation in red and are a required closeout deliverable — they also feed the NFPA 72 record of completion and the documentation retained at the panel.
Exam Watchouts
Important
Written dimensions govern over scaled dimensions. If the drawing says 28'-0" and your architect's scale says 27'-6", build to 28'-0" and issue an RFI if the discrepancy matters.
Warning
The riser diagram is not to scale. Conductor lengths for voltage-drop calculations come from the plan view and the vertical rise, never from measuring the riser sheet.
Tip
Cross-check the fire alarm plan against the reflected ceiling plan and the mechanical drawings before laying out. Smoke detectors that land on a supply diffuser, and duct detectors specified for a unit under 2,000 CFM, are the two conflicts that most often force rework.