Study guide
17.1 Pumps, Blowers and Mechanical Maintenance Programs
Oregon Water and Wastewater Operator Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Oregon Operator Programs and DEQ Wastewater Certification
1.1 Dual-Agency Structure: DEQ Wastewater and OHA Drinking Water Programs 1.2 DEQ Wastewater System Classification and Supervision Rules 1.3 DEQ Certificates: Qualifications, OIT, Provisional Path, Exams and Fees
2 Chapter 2: OHA Drinking Water Certification and Certificate Renewal
2.1 OHA System Classification, Direct Responsible Charge and the Filtration Endorsement 2.2 OHA Certificates: Experience Tables, OIT, Exams, Fees and Small Water System Certification 2.3 Renewal, CEUs, Reinstatement, Reciprocity and Discipline for DEQ and OHA Certificates
3 Chapter 3: Federal Rules, Oregon Water Quality Standards and Cyanotoxins
3.1 Clean Water Act, Safe Drinking Water Act & NPDES Permitting 3.2 Willamette Basin TMDL and Oregon Water Quality Standards 3.3 Harmful Algal Blooms (HABs) & Oregon Cyanotoxin Rules (OAR 333-061-0510)
4 Chapter 4: Source Water, Intakes and Wells
4.1 Raw Water Sources, Intake Structures & Pretreatment 4.2 Groundwater Sources and Wells: Hydraulics, Construction and Protection
5 Chapter 5: Coagulation, Clarification and Filtration
5.1 Coagulation, Flocculation & Jar Testing Dynamics 5.2 Sedimentation, Clarification & Media Filtration Systems 5.3 Slow Sand, Diatomaceous Earth, Cartridge and Membrane Filtration
6 Chapter 6: Drinking Water Disinfection
6.1 Disinfection Chemistry, Chlorination Dynamics & CT Calculations 6.2 UV, Ozone, Chlorine Dioxide, Chloramines and Disinfection Byproduct Control
7 Chapter 7: Specialty Water Treatment and Residuals
7.1 Iron and Manganese Removal, Softening, and Taste and Odor Control 7.2 Corrosion Control, Lead and Copper, and Fluoridation 7.3 Water Treatment Residuals: Sludge, Backwash Water and Membrane Concentrate
8 Chapter 8: Distribution System Infrastructure
8.1 Distribution System Hydraulics, Piping Materials & Storage Facilities 8.2 Valves, Fire Hydrants & Water Main Installation / Disinfection 8.3 Service Connections, Meters, Water Loss Control and Utility Locating
9 Chapter 9: Distribution Operations, Cross-Connection Control and Water Quality
9.1 Storage Tank and Booster Pump Station Operation, Inspection and Disinfection 9.2 Cross-Connection Control & Backflow Prevention Assemblies (OAR 333-061-0070) 9.3 Water Quality in Distribution: Water Age, Nitrification & Flushing Programs
10 Chapter 10: Wastewater Preliminary and Primary Treatment and Lagoons
10.1 Preliminary Treatment: Screening, Grit Removal & Flow Measurement 10.2 Primary Clarification & Sedimentation Hydraulics 10.3 Stabilization Ponds and Aerated Lagoons
11 Chapter 11: Biological Wastewater Treatment
11.1 Secondary Treatment: Activated Sludge Process Control & Variations 11.2 Fixed-Film Treatment: Trickling Filters, RBCs, MBBR and IFAS 11.3 Biological Nutrient Removal: Nitrification, Denitrification & Phosphorus Removal
12 Chapter 12: Tertiary Treatment, Disinfection, Recycled Water and Small Systems
12.1 Tertiary Filtration, Membrane Bioreactors and Oregon Recycled Water Classes 12.2 Wastewater Disinfection and Dechlorination 12.3 Small Wastewater Systems, Septage Handling and Odor Control
13 Chapter 13: Solids Handling and Biosolids
13.1 Sludge Thickening, Conditioning & Dewatering Technologies 13.2 Anaerobic and Aerobic Digestion Operations & Control 13.3 Biosolids Quality, Land Application Rules & OAR 340-050 / 40 CFR 503
14 Chapter 14: Wastewater Collection Systems and Pumping
14.1 Gravity Sewer Design, Manholes & Inflow/Infiltration (I/I) Management 14.2 Lift Station Design, Wet Wells & Submersible / Centrifugal Pumps 14.3 Collection System Maintenance, Pipeline Inspection (CCTV) & Trench Safety
15 Chapter 15: Collection System Rehabilitation and Overflow Control
15.1 Sewer Rehabilitation, Trenchless Renewal and New-Pipe Acceptance Testing 15.2 Overflow Response, Bypass Pumping, CMOM Programs and Sewer Sulfide Control
16 Chapter 16: Laboratory Procedures and Water Quality Testing
16.1 Drinking Water Microbiological Testing: Coliform, E. coli & RTCR 16.2 Wastewater Lab Analysis: BOD5, TSS, COD & Volatile Solids 16.3 Wastewater Lab: Nutrients, Alkalinity, Bacteria, Toxicity Testing and Lab Accreditation 16.4 Process Monitoring: pH, Turbidity, Dissolved Oxygen & Chlorine Residuals 16.5 Sampling Protocols, Quality Assurance / Chain of Custody & Reporting
17 Chapter 17: Equipment, Electrical Systems and Maintenance
17.1 Pumps, Blowers and Mechanical Maintenance Programs 17.2 Electrical Systems, Motors, Generators, Instrumentation and SCADA
18 Chapter 18: Applied Water and Wastewater Mathematics
18.1 Dimensional Analysis, Flow Conversions & Detention Time 18.2 Chemical Feed, Dosage Calculations & the Pounds Formula 18.3 Treatment Plant Hydraulics, Loading Rates (SOR, WOR) & Pumping Horsepower
19 Chapter 19: Utility Safety
19.1 OSHA Standards, Confined Space Entry & Hazardous Chemical Safety 19.2 Field Safety: Electrical Hazards, Fall Protection, Work Zones, PPE and Oregon OSHA Rules
20 Chapter 20: Emergency Preparedness, Security and Utility Management
20.1 Cascadia Subduction Zone (CSZ) Seismic Preparedness & Infrastructure Hardening 20.2 Wildfire Impacts on Watersheds, Post-Fire Water Quality & Emergency Operations 20.3 Security, Cybersecurity, Emergency Response Planning and Utility Management
17.1 Pumps, Blowers and Mechanical Maintenance Programs
Key Takeaways Explain This Topic AI
Centrifugal pumps deliver less flow as head rises along their curve and run best near the best efficiency point; positive displacement pumps deliver nearly constant flow and need relief protection against closed discharge valves.
By the affinity laws, flow varies with speed, head with speed squared, and power with speed cubed, so a 10 percent speed cut saves about 27 percent of the power.
Packing should drip slightly (often cited as about 40 to 60 drops per minute) for cooling and lubrication; mechanical seals should not leak and are damaged by running dry.
Most bearing failures come from contamination, misalignment and lubrication errors, including over-greasing; laser or dial-indicator alignment and vibration analysis prevent them.
Preventive maintenance is scheduled, predictive maintenance uses condition data such as vibration, temperature and oil analysis, and a computerized maintenance management system tracks work orders and asset history.
Last updated: October 2026
Pump Types
Type Examples Behavior Typical uses
Centrifugal End-suction, split-case, vertical turbine, submersible, non-clog Flow changes with system head along the pump curve Water distribution, raw water, lift stations, RAS
Positive displacement (PD) Progressive cavity, plunger, diaphragm, peristaltic (hose), rotary lobe Delivers a nearly fixed volume per stroke or revolution regardless of head Sludge, chemical metering, polymer
Never start or run a PD pump against a closed discharge valve. Pressure climbs until something breaks, so PD pumps need pressure relief valves and should never be throttled to control flow. Centrifugal pumps can run briefly against a closed valve at shutoff head, but they overheat if left there.
Pump Curves
A centrifugal pump curve shows head, efficiency, brake horsepower and NPSH required against flow. The operating point is where the pump curve crosses the system curve (static head plus friction losses).
Running far left of the best efficiency point (BEP) , at low flow, causes recirculation, heat, vibration and seal and bearing wear.
Running far right, at high flow, risks cavitation and motor overload.
Parallel pumps add flow at the same head; series pumps add head at the same flow.
Affinity Laws (same pump, changed speed) Q 2 Q 1 = N 2 N 1 H 2 H 1 = ( N 2 N 1 ) 2 P 2 P 1 = ( N 2 N 1 ) 3 \frac{Q_2}{Q_1} = \frac{N_2}{N_1} \qquad \frac{H_2}{H_1} = \left(\frac{N_2}{N_1}\right)^2 \qquad \frac{P_2}{P_1} = \left(\frac{N_2}{N_1}\right)^3 Q 1 Q 2 = N 1 N 2 H 1 H 2 = ( N 1 N 2 ) 2 P 1 P 2 = ( N 1 N 2 ) 3
Example. A pump delivers 1,000 gpm at 1,780 rpm. A VFD slows it to 1,500 rpm, a speed ratio of 0.843.
- Flow ≈ 1,000 × 0.843 = 843 gpm
- Head ≈ 0.843² = 71 percent of the original
- Power ≈ 0.843³ = 60 percent of the original
That cube relationship is why VFDs save so much energy on variable-demand pumps and blowers.
Shaft Sealing
Seal How it works Operator checks
Packing Rings of braided packing in a stuffing box, compressed by a gland; a lantern ring feeds seal water Allow a slight steady drip (often cited as about 40-60 drops per minute) for cooling. Tighten the gland nuts evenly and gradually. Over-tightening burns packing and scores the shaft sleeve.
Mechanical seal Rotating and stationary faces lapped flat, held together by springs Should not visibly leak. Never run dry, because the faces overheat and crack. Flush water and correct installation length are critical.
When repacking: remove all old rings, check the sleeve for wear, cut new rings to fit, and stagger the joints (about 90 to 120 degrees apart). Seat each ring separately and position the lantern ring under the seal water port.
Bearings, Lubrication and Alignment
Bearing failure causes : contamination (dirt and water), misalignment, imbalance, improper lubrication and electrical fluting from VFDs.
Lubrication : follow the manufacturer's type, quantity and interval. Over-greasing packs the housing, raises temperature and blows seals. Keep grease guns clean and labeled, and never mix incompatible greases.
Alignment : use dial-indicator or laser alignment. Correct angular and offset (parallel) misalignment, check for soft foot before final alignment, and recheck after the pump reaches operating temperature where required.
Couplings, belts and chains : inspect for wear. Tension belts correctly, since a loose belt slips and a tight one destroys bearings.
Blowers and Compressors
Positive displacement (rotary lobe) blowers deliver nearly constant air volume. They need relief valves, inlet filters and silencers, and must not be dead-headed.
Multistage centrifugal and high-speed turbo blowers run efficiently over a narrower range and must be kept out of surge , an unstable flow reversal at low flow and high pressure.
Air compressors : drain receiver condensate, test relief valves, change filters, and inspect pressure vessels as required.
Monitor diffuser pressure: rising header pressure at the same airflow points to diffuser fouling.
Maintenance Strategies
- Strategy Basis Examples
- Corrective (breakdown) Fix after failure Acceptable only for cheap, non-critical items
Preventive (PM) Calendar or runtime schedule Oil changes, lubrication routes, filter changes, exercising valves and generators
Predictive (PdM) Condition monitoring Vibration analysis, infrared thermography of motors and electrical panels, oil analysis, ultrasonic leak and bearing checks, motor current analysis
Reliability-centered Criticality and failure modes Spend effort where failure consequences are highest
A computerized maintenance management system (CMMS) schedules PM and records work orders, labor, parts and costs. It also builds equipment history, which supports asset management : knowing what you own, its condition and criticality, and when to repair or replace it. Keep spare parts for critical equipment, and keep O&M manuals, pump curves and as-built drawings where crews can use them.
Valves Worth Knowing
Gate (isolation), butterfly (isolation and throttling in large lines), plug and eccentric plug (sludge), ball, globe (throttling), check (swing, ball, silent), pressure-reducing and -sustaining, and air release and vacuum valves. Exercise isolation valves on a schedule so they work in an emergency, and record turns and condition.