Study guide
3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP)
OSHA 30-Hour Construction Safety Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety Management, Regulatory Framework & Worker Rights
1.1 OSHA Regulatory Structure, OSH Act, General Duty Clause & Worker Rights 1.2 Safety Management Systems (SMS) & Safety Culture Leadership 1.3 Leading vs. Lagging Indicators, Safety Metrics & Recordkeeping (OSHA 300/300A/301) 1.4 Multi-Employer Worksite Citation Policy & Subcontractor Safety Oversight 1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)
2 Chapter 2: Fall Protection Systems & Working at Heights
2.1 Fall Hazards, 6-Foot Rule & 29 CFR 1926 Subpart M Scope 2.2 Guardrail Systems, Safety Net Systems & Hole Covers 2.3 Personal Fall Arrest Systems (PFAS), Anchorages & Fall Clearance Calculations 2.4 Controlled Access Zones, Safety Monitoring Systems & Leading Edge Work 2.5 Stairways, Ladders & Access Systems (29 CFR 1926 Subpart X)
3 Chapter 3: Electrical Safety, Grounding & Energy Control
3.1 Electrical Hazards, Electrocution Dynamics & 29 CFR 1926 Subpart K 3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP) 3.3 Overhead Power Line Clearances & Encroachment Prevention 3.4 Lockout/Tagout (LOTO), De-energization & Hazardous Energy Control 3.5 Arc Flash Hazards, PPE Requirements & Qualified Worker Distinctions
4 Chapter 4: Scaffolding Systems & Aerial Lifts
4.1 Scaffold Classifications, Load Capacities & Subpart L General Requirements 4.2 Supported Scaffolds: Foundations, Planking, Bracing, Tie-ins & Erection 4.3 Suspended Scaffolds, Two-Point Swings & Rigging Counterweights 4.4 Aerial Lifts, Scissor Lifts & Mobile Elevated Work Platforms (MEWPs) 4.5 Competent Person Scaffold Inspection, Fall Protection & Access Rules
5 Chapter 5: Excavation, Trenching & Shoring Safety
5.1 Excavation Hazards, Soil Mechanics & Subpart P Scope 5.2 OSHA Soil Classification: Visual and Manual Field Testing (Types A, B, C) 5.3 Protective Systems: Sloping and Benching Ratios 5.4 Protective Systems: Hydraulic Shoring, Trench Boxes & Shields 5.5 Excavation Access/Egress, Hazardous Atmospheres & Competent Person Daily Inspections
6 Chapter 6: Cranes, Derricks, Hoists & Rigging
6.1 Subpart CC Scope, Operator Certification & Qualification Requirements 6.2 Crane Setup, Ground Conditions, Outriggers & Power Line Safety 6.3 Load Charts, Capacity Calculations & Lift Planning 6.4 Critical Lift Planning, Tandem Lifts & Personnel Hoisting 6.5 Rigging Hardware, Sling Angles, Hitches & Signal Person Qualifications
7 Chapter 7: Confined Spaces in Construction
7.1 29 CFR 1926 Subpart AA Scope & Confined Space vs. Permit-Required Confined Space (PRCS) 7.2 Atmospheric Testing: Sequential Order (O2, Flammability, Toxicity) & Calibration 7.3 PRCS Entry Permit Program, Isolation & Ventilation 7.4 Duties of Authorized Entrants, Attendants & Entry Supervisors 7.5 Non-Entry vs. Entry Rescue, Emergency Services & Retrieval Systems
8 Chapter 8: Incident Investigation, Root Cause Analysis & Prevention
8.1 Purpose of Incident Investigation & Blame-Free Reporting Culture 8.2 Immediate Response, Scene Security, Evidence Gathering & Witness Interviewing 8.3 Root Cause Analysis Methodologies: 5 Whys, Fishbone (Ishikawa), and Fault Tree 8.4 Human Factors, Swiss Cheese Model & Latent Organizational Failures 8.5 Corrective Action Plans, Hierarchy of Controls Application & Near-Miss Trending
9 Chapter 9: Occupational Health Hazards & Environmental Protection
9.1 Hazard Communication Standard (HazCom 2012 / GHS) & 16-Section Safety Data Sheets (SDSs) 9.2 Respirable Crystalline Silica (29 CFR 1926.1153) & Table 1 Control Methods 9.3 Lead & Asbestos Hazards in Construction Demolition and Renovation (29 CFR 1926.62 / 1926.1101) 9.4 Occupational Noise Exposure, Action Levels, PELs & Hearing Conservation Programs (Subpart D) 9.5 Thermal Stress (Heat Illness & Cold Injury Prevention) & Biological/Chemical Hazards
10 Chapter 10: Ergonomics, Material Handling & Tool Safety
10.1 Ergonomic Risk Factors in Construction & Musculoskeletal Disorders (MSDs) 10.2 Manual Material Handling, Safe Lifting Principles & Ergonomic Engineering Solutions 10.3 Hand-Arm Vibration Syndrome (HAVS), Whole-Body Vibration & Power Tool Safety (Subpart I) 10.4 Material Storage, Rigging Safety, Housekeeping & Disposal (29 CFR 1926 Subpart H) 10.5 Motor Vehicles, Heavy Equipment, Highway Work Zone Safety & Struck-By Prevention (Subpart O/G)
11 Chapter 11: Personal Protective and Life-Saving Equipment (29 CFR 1926 Subpart E)
11.1 PPE Programs, Hazard Assessment, the Proper-Fit Rule & Employer Payment 11.2 Head, Eye, and Face Protection (1926.100 / 1926.102) 11.3 Hearing, Hand, Foot, and Body Protection (1926.101 / 1926.95 / 1926.96) 11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing (1926.103)
12 Chapter 12: Struck-By and Caught-In/Between Focus Four Hazards
12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects 12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection 12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts (1926.602)
13 Chapter 13: Concrete, Masonry & Steel Erection (Subparts Q and R)
13.1 Cast-in-Place Concrete, Formwork, Shoring & Rebar Impalement (Subpart Q) 13.2 Masonry Construction, Limited Access Zones & Precast/Tilt-Up Panels (Subpart Q) 13.3 Steel Erection: Column Anchorage, Connectors, Decking & the CDZ (Subpart R)
14 Chapter 14: Fire Prevention, Welding & Cutting, and Demolition (Subparts F, J, T)
14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F) 14.2 Welding, Cutting & Hot Work (29 CFR 1926 Subpart J) 14.3 Demolition: Engineering Surveys & Sequenced Removal (29 CFR 1926 Subpart T)
15 Chapter 15: Emergency Preparedness, Site Welfare & Safety Leadership
15.1 Emergency Action Plans, Medical Services, First Aid & Sanitation (1926.35 / .50 / .51) 15.2 Foundations for Safety Leadership & the OSHA Outreach Card
3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP)
Key Takeaways Explain This Topic AI
29 CFR 1926.404(b)(1) mandates that employers provide either Ground Fault Circuit Interrupters (GFCIs) on all 120 V, single-phase, 15- and 20-ampere temporary receptacle outlets OR implement an Assured Equipment Grounding Conductor Program (AEGCP).
GFCIs continuously monitor current balance between the hot (ungrounded) and neutral (grounded) conductors, rapidly de-energizing the circuit within 25 milliseconds (1/40th of a second) when an imbalance of 4 to 6 mA is detected.
GFCIs protect against line-to-ground faults but do NOT protect against line-to-line contact (touching hot and neutral simultaneously without grounding).
An AEGCP requires a written program, designated competent person, daily visual pre-use inspections, and mandatory continuity and polarity testing every 3 months (or before first use, after repairs, or after suspected damage) logged with color-coded tagging.
All extension cords on construction sites must be heavy-duty 3-wire grounded types rated for hard or extra-hard usage (e.g., S, ST, SO, STO, SJ, SJO).
Last updated: August 2026
3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP)
OSHA Standard Mandatory Rule: Under 29 CFR 1926.404(b)(1)(i) , employers on construction sites must protect employees utilizing temporary 120-volt, single-phase, 15- and 20-ampere receptacle outlets by providing either Ground Fault Circuit Interrupters (GFCIs) or by establishing an Assured Equipment Grounding Conductor Program (AEGCP) . This requirement applies to all temporary electric power receptacles used during construction, alteration, repair, or demolition.
Operating Principles of Ground Fault Circuit Interrupters (GFCI)
A Ground Fault Circuit Interrupter (GFCI) is a high-speed electrical safety device engineered to detect tiny current leakages that escape an intended circuit path. Unlike fuses and standard breakers that protect equipment, a GFCI is a life-safety device specifically designed to protect biological human tissue.
How a GFCI Senses Faults
Inside a GFCI receptacle or breaker, an internal differential current transformer (toroid sensing coil) monitors the magnetic fields generated by current passing through the ungrounded "hot" conductor (typically black or red) and returning through the grounded "neutral" conductor (typically white):
Normal Circuit State: In a healthy circuit, the incoming current on the hot wire equals the outgoing current on the neutral wire ( I hot = I neutral I_{\text{hot}} = I_{\text{neutral}} I hot = I neutral ). The opposing magnetic fields cancel each other out completely, producing a net zero magnetic flux in the sensing toroid.
Ground Fault Occurrence: If an energized conductor frays and touches a tool's metal frame, or if a worker contacts the hot conductor, a portion of the current leaks to ground through the worker's body, concrete slab, or equipment chassis. Now, I hot > I neutral I_{\text{hot}} > I_{\text{neutral}} I hot > I neutral .
High-Speed Tripping: The differential toroid senses this current imbalance. When the differential reaches 4 to 6 milliamperes (mA) 4\text{ to }6\text{ milliamperes (mA)} 4 to 6 milliamperes (mA) , solid-state circuitry triggers a mechanical relay that opens the circuit.
Trip Speed: The GFCI de-energizes the circuit in approximately 1 / 40 th of a second (25 milliseconds) 1/40\text{th of a second (25 milliseconds)} 1/40 th of a second (25 milliseconds) . This lightning-fast interruption cuts current flow long before ventricular fibrillation can occur. [Hot Conductor (10.000 A)] --------> [Power Tool Motor]
- |
- [Leakage Path (0.005 A to Ground via Worker)]
- |
- [Neutral Return (9.995 A)] <----------------+
Toroid Sensor Detects: 10.000 A - 9.995 A = 0.005 A (5 mA Delta)
ACTION: Relay Trips Instantly within 25 Milliseconds!
Critical Limitation of GFCIs
A GFCI does NOT protect a worker from line-to-line contact. If a worker simultaneously grasps the hot conductor with one hand and the neutral conductor with the other without any current escaping to ground, the GFCI senses identical current flowing in both conductors ( I hot = I neutral I_{\text{hot}} = I_{\text{neutral}} I hot = I neutral ). The device cannot distinguish between a human body and a light bulb, and will not trip .
Types of GFCIs on Construction Sites
Circuit Breaker GFCIs: Installed directly in the power distribution panelboard; protects the entire home run and all downstream outlets.
Receptacle GFCIs: Integrated directly into temporary spider boxes, wall outlets, or generator panel faces.
Portable / In-Line Cord GFCIs: Heavy-duty pigtail units plugged directly between permanent building outlets and jobsite extension cords. Portable units feature "open-neutral protection" to ensure safety even if the building source neutral conductor is severed.
The Assured Equipment Grounding Conductor Program (AEGCP)
If an employer chooses not to provide GFCIs on temporary 120 V 15 A and 20 A receptacles, or when utilizing receptacles operating at higher voltages (e.g., 240 V, 480 V single-phase or three-phase), they must establish a formal, written Assured Equipment Grounding Conductor Program (AEGCP) under 29 CFR 1926.404(b)(1)(iii) .
Core Elements of a Compliant AEGCP
A legally defensible AEGCP consists of six mandatory components:
Written Site Program: A comprehensive written document outlining program policies, testing procedures, designated personnel, and recordkeeping must be maintained on-site and made immediately available to OSHA compliance officers and employees.
Designated Competent Person: The employer must designate one or more competent persons with the training, electrical knowledge, and authority to implement, monitor, and enforce the program.
Daily Visual Inspection: Before each day's use, employees and supervisors must visually inspect all flexible cords, cord sets, attachment caps, plugs, and receptacles for external damage (e.g., deformed or missing ground pins, cracked casings, pinched jackets, damaged outer insulation).
Mandatory Electrical Testing: Two specific electrical tests must be performed on all equipment grounding conductors:
Continuity Test: Verifies that the equipment grounding conductor is electrically continuous from plug to receptacle/tool.
Polarity & Terminal Connection Test: Verifies that the ungrounded (hot), grounded (neutral), and grounding conductors are correctly connected to their proper respective terminals.
Mandatory Testing Intervals: Electrical testing must be conducted:
- Before first use on the jobsite;
- Before equipment is returned to service following any repair or modification;
- After any incident where equipment damage is suspected (e.g., running over a cord with a telehandler);
At intervals not to exceed 3 months (for fixed cords and receptacles not exposed to damage) or 6 months (for permanent installations).
Recordkeeping & Color-Coded Tagging: Test results must be logged in a dedicated record identifying each piece of equipment, date of inspection, and test results. Standard construction practice utilizes a quarterly color-coded tape system applied to tested cords:
- Quarter / Month Standard Construction Tagging Color
- Q1 (Jan, Feb, Mar) White
- Q2 (Apr, May, Jun) Green
- Q3 (Jul, Aug, Sep) Red
- Q4 (Oct, Nov, Dec) Orange
- Extension Cord Safety & Design Classifications
Under 29 CFR 1926.405(a)(2)(ii)(J) , flexible cords and cables used on construction sites must be 3-wire grounded types designed for hard or extra-hard usage .
Cord Designation Lettering Code (NEC / UL Markings)
Cord jackets must be stamped with industry designation codes indicating durability:
- S: Severe / Extra-Hard Service (600 V rated)
- SJ: Junior Hard Service (300 V rated)
- T: Thermoplastic / Vinyl insulation
- O: Oil-resistant outer jacket
- OO: Oil-resistant inner conductor insulation AND outer jacket
- W: Weather and water-resistant (approved for outdoor/wet jobsite use)
Acceptable jobsite cord types include S, SO, SOO, ST, STO, STOO, SJ, SJO, SJT, SJTO, SJW , provided they are rated for the environment. Standard household zip-cords (SPT type) are strictly prohibited on construction jobsites. ACCEPTABLE (Heavy-Duty Industrial): PROHIBITED (Household Grade):
- [ SOOW 12/3 Heavy-Duty Outdoor Cord ] [ SPT-2 Flat 2-Wire Lamp Cord ]
- ✓ 3-Wire Grounded (Heavy Pin) ✗ 2-Wire Ungrounded (No Pin)
- ✓ Heavy Reinforced Rubber Jacket ✗ Thin Plastic Casing Cracks Easily
- ✓ Oil, Water, Abrasion Resistant ✗ Not Rated for Physical Abuse
- Prohibited Cord Practices on Construction Sites
Never run flexible cords through holes in walls, ceilings, floors, doorways, or windows unless physically protected from pinching.
Never fasten cords with staples, nails, or bare tie-wire; only use non-conductive hooks or nylon straps.
Never bypass, snip off, or bend the round grounding prong on a 3-prong plug.
Never splice extension cords; damaged cords must be removed from service or cut back and terminated with an approved replacement cord cap by a qualified person.
Do not daisy-chain multiple extension cords together; voltage drop increases current draw, overheating the conductors and causing premature GFCI tripping.
- Practical Field Scenarios & Common Exam Traps
- Practical Field Scenario
A concrete crew is vibrating a foundation pour in rainy conditions using a 120 V 120\text{ V} 120 V generator. The generator has built-in standard duplex receptacles without integral GFCIs. The crew plugs a 3-wire extension cord into the generator and attaches a vibrator. Because the generator frame is resting on wooden blocks, it is not grounded to earth.
Safety Violation: Under OSHA rules, even with a portable generator, if the unit supplies 120 V 120\text{ V} 120 V , 15/20 A power to portable tools, workers must be protected by GFCIs or an AEGCP. Resting on wood blocks eliminates any path to earth.
Corrective Action: The crew must insert an approved portable in-line GFCI pigtail directly at the generator receptacle outlet before connecting extension cords.
Common Exam Traps
Trap 1: Assuming permanent building power does not need GFCI protection during construction. If construction workers use permanent building 120 V outlets during renovation, GFCI or AEGCP protection is still 100% mandatory.
Trap 2: Believing AEGCP requires only daily visual checks. An AEGCP is invalid without mandatory instrument testing (continuity and polarity) conducted at intervals not exceeding 3 months and recorded in an accessible log.
Trap 3: Thinking a GFCI trips at 15 A or 20 A. GFCIs trip at 4 to 6 mA of ground fault current. The 15 A or 20 A rating on the face indicates normal load-carrying capacity, not the trip threshold.