Study guide
15.2 Foundations for Safety Leadership & the OSHA Outreach Card
OSHA 30-Hour Construction Safety Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety Management, Regulatory Framework & Worker Rights
1.1 OSHA Regulatory Structure, OSH Act, General Duty Clause & Worker Rights 1.2 Safety Management Systems (SMS) & Safety Culture Leadership 1.3 Leading vs. Lagging Indicators, Safety Metrics & Recordkeeping (OSHA 300/300A/301) 1.4 Multi-Employer Worksite Citation Policy & Subcontractor Safety Oversight 1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)
2 Chapter 2: Fall Protection Systems & Working at Heights
2.1 Fall Hazards, 6-Foot Rule & 29 CFR 1926 Subpart M Scope 2.2 Guardrail Systems, Safety Net Systems & Hole Covers 2.3 Personal Fall Arrest Systems (PFAS), Anchorages & Fall Clearance Calculations 2.4 Controlled Access Zones, Safety Monitoring Systems & Leading Edge Work 2.5 Stairways, Ladders & Access Systems (29 CFR 1926 Subpart X)
3 Chapter 3: Electrical Safety, Grounding & Energy Control
3.1 Electrical Hazards, Electrocution Dynamics & 29 CFR 1926 Subpart K 3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP) 3.3 Overhead Power Line Clearances & Encroachment Prevention 3.4 Lockout/Tagout (LOTO), De-energization & Hazardous Energy Control 3.5 Arc Flash Hazards, PPE Requirements & Qualified Worker Distinctions
4 Chapter 4: Scaffolding Systems & Aerial Lifts
4.1 Scaffold Classifications, Load Capacities & Subpart L General Requirements 4.2 Supported Scaffolds: Foundations, Planking, Bracing, Tie-ins & Erection 4.3 Suspended Scaffolds, Two-Point Swings & Rigging Counterweights 4.4 Aerial Lifts, Scissor Lifts & Mobile Elevated Work Platforms (MEWPs) 4.5 Competent Person Scaffold Inspection, Fall Protection & Access Rules
5 Chapter 5: Excavation, Trenching & Shoring Safety
5.1 Excavation Hazards, Soil Mechanics & Subpart P Scope 5.2 OSHA Soil Classification: Visual and Manual Field Testing (Types A, B, C) 5.3 Protective Systems: Sloping and Benching Ratios 5.4 Protective Systems: Hydraulic Shoring, Trench Boxes & Shields 5.5 Excavation Access/Egress, Hazardous Atmospheres & Competent Person Daily Inspections
6 Chapter 6: Cranes, Derricks, Hoists & Rigging
6.1 Subpart CC Scope, Operator Certification & Qualification Requirements 6.2 Crane Setup, Ground Conditions, Outriggers & Power Line Safety 6.3 Load Charts, Capacity Calculations & Lift Planning 6.4 Critical Lift Planning, Tandem Lifts & Personnel Hoisting 6.5 Rigging Hardware, Sling Angles, Hitches & Signal Person Qualifications
7 Chapter 7: Confined Spaces in Construction
7.1 29 CFR 1926 Subpart AA Scope & Confined Space vs. Permit-Required Confined Space (PRCS) 7.2 Atmospheric Testing: Sequential Order (O2, Flammability, Toxicity) & Calibration 7.3 PRCS Entry Permit Program, Isolation & Ventilation 7.4 Duties of Authorized Entrants, Attendants & Entry Supervisors 7.5 Non-Entry vs. Entry Rescue, Emergency Services & Retrieval Systems
8 Chapter 8: Incident Investigation, Root Cause Analysis & Prevention
8.1 Purpose of Incident Investigation & Blame-Free Reporting Culture 8.2 Immediate Response, Scene Security, Evidence Gathering & Witness Interviewing 8.3 Root Cause Analysis Methodologies: 5 Whys, Fishbone (Ishikawa), and Fault Tree 8.4 Human Factors, Swiss Cheese Model & Latent Organizational Failures 8.5 Corrective Action Plans, Hierarchy of Controls Application & Near-Miss Trending
9 Chapter 9: Occupational Health Hazards & Environmental Protection
9.1 Hazard Communication Standard (HazCom 2012 / GHS) & 16-Section Safety Data Sheets (SDSs) 9.2 Respirable Crystalline Silica (29 CFR 1926.1153) & Table 1 Control Methods 9.3 Lead & Asbestos Hazards in Construction Demolition and Renovation (29 CFR 1926.62 / 1926.1101) 9.4 Occupational Noise Exposure, Action Levels, PELs & Hearing Conservation Programs (Subpart D) 9.5 Thermal Stress (Heat Illness & Cold Injury Prevention) & Biological/Chemical Hazards
10 Chapter 10: Ergonomics, Material Handling & Tool Safety
10.1 Ergonomic Risk Factors in Construction & Musculoskeletal Disorders (MSDs) 10.2 Manual Material Handling, Safe Lifting Principles & Ergonomic Engineering Solutions 10.3 Hand-Arm Vibration Syndrome (HAVS), Whole-Body Vibration & Power Tool Safety (Subpart I) 10.4 Material Storage, Rigging Safety, Housekeeping & Disposal (29 CFR 1926 Subpart H) 10.5 Motor Vehicles, Heavy Equipment, Highway Work Zone Safety & Struck-By Prevention (Subpart O/G)
11 Chapter 11: Personal Protective and Life-Saving Equipment (29 CFR 1926 Subpart E)
11.1 PPE Programs, Hazard Assessment, the Proper-Fit Rule & Employer Payment 11.2 Head, Eye, and Face Protection (1926.100 / 1926.102) 11.3 Hearing, Hand, Foot, and Body Protection (1926.101 / 1926.95 / 1926.96) 11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing (1926.103)
12 Chapter 12: Struck-By and Caught-In/Between Focus Four Hazards
12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects 12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection 12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts (1926.602)
13 Chapter 13: Concrete, Masonry & Steel Erection (Subparts Q and R)
13.1 Cast-in-Place Concrete, Formwork, Shoring & Rebar Impalement (Subpart Q) 13.2 Masonry Construction, Limited Access Zones & Precast/Tilt-Up Panels (Subpart Q) 13.3 Steel Erection: Column Anchorage, Connectors, Decking & the CDZ (Subpart R)
14 Chapter 14: Fire Prevention, Welding & Cutting, and Demolition (Subparts F, J, T)
14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F) 14.2 Welding, Cutting & Hot Work (29 CFR 1926 Subpart J) 14.3 Demolition: Engineering Surveys & Sequenced Removal (29 CFR 1926 Subpart T)
15 Chapter 15: Emergency Preparedness, Site Welfare & Safety Leadership
15.1 Emergency Action Plans, Medical Services, First Aid & Sanitation (1926.35 / .50 / .51) 15.2 Foundations for Safety Leadership & the OSHA Outreach Card
15.2 Foundations for Safety Leadership & the OSHA Outreach Card
Key Takeaways Explain This Topic AI
Foundations for Safety Leadership is the only 30-hour Construction elective with a minimum length longer than 30 minutes — the Construction Industry Procedures set it at a minimum of 2 hours and 30 minutes.
The FSL module teaches five safety leadership skills: lead by example; engage and empower team members; actively listen and practice three-way communication; develop team members through teaching, coaching, and feedback; and recognize team members for going above and beyond for safety.
The 30-hour Construction Outreach class is not considered equivalent to the OSHA #510 Occupational Safety and Health Standards for the Construction Industry course, which is offered only through OTI Education Centers.
Construction Outreach trainers must complete either the OSHA #502 update or the OSHA #500 trainer course every four years to maintain authorization.
Student course completion cards in Construction, General Industry, Maritime, and Disaster Site do not expire, but trainers retain class records for five years and may issue only one replacement card per student per class.
Last updated: August 2026
15.2 Foundations for Safety Leadership & the OSHA Outreach Card
The OSHA Outreach Training Program, Construction Industry Procedures describes the 30-hour course as "intended to provide a variety of training to workers with some safety responsibilities." That single phrase is what separates the 30-hour from the 10-hour: the audience is foremen, superintendents, and lead workers who direct other people's work. Technical hazard knowledge alone does not make that person effective — they also have to be able to raise a safety concern with a project manager, stop a crew without losing them, and get an apprentice to report a near miss.
That gap is why OSHA added a leadership elective.
1. Foundations for Safety Leadership (FSL)
FSL was developed by CPWR — The Center for Construction Research and Training with a 17-member curriculum development team of contractors, unions, outreach trainers, safety professionals, and instructional designers. OSHA's Training Institute made it an official elective in the 30-hour Construction course at the start of 2017 .
Its unique status in the curriculum
Recall the elective rule from the Construction Industry Procedures: "Elective – 12 hours. Must present at least 12 hours of training on the following topics. At least six of the topics must be presented. The minimum length of any topic is 30 minutes, except for Foundations for Safety Leadership. " The listed minimum for FSL is 2 hours and 30 minutes .
Note
This is a genuinely testable curriculum fact. Every other elective — scaffolds, cranes, excavations, confined spaces, ergonomics, steel erection — carries a 30-minute floor. FSL is the single named exception, because the module is built around interactive scenarios and role plays that do not compress.
The five safety leadership skills THE FIVE FSL SAFETY LEADERSHIP SKILLS
- L ─ LEAD BY EXAMPLE
- E ─ ENGAGE AND EMPOWER TEAM MEMBERS
- A ─ ACTIVELY LISTEN AND PRACTICE 3-WAY COMMUNICATION
- DE─ DEVELOP TEAM MEMBERS THROUGH TEACHING, COACHING & FEEDBACK
- R ─ RECOGNIZE TEAM MEMBERS FOR GOING ABOVE AND BEYOND FOR SAFETY
Skill What It Looks Like on a Jobsite
Lead by Example The most important of the five. Always wear the required PPE yourself; never take or encourage a shortcut; conduct daily safety huddles; consider the safety implications of your decisions and share that reasoning with the crew; hold everyone — including yourself — accountable. Crews learn from what a leader does , not what a leader posts.
Engage and Empower Team Members Ask the crew how to carry out the task safely rather than telling them; involve them in the JHA; give real Stop Work Authority and back it when it is used; let the person doing the work shape the method.
Actively Listen and Practice 3-Way Communication Give full attention, ask open-ended questions, and confirm understanding. Three-way communication means the sender gives the message, the receiver repeats it back in their own words, and the sender confirms it was received correctly — the same closed-loop discipline used in crane signaling (Section 6.5) and confined space entry (Section 7.4).
Develop Team Members Through Teaching, Coaching, and Feedback Treat a mistake as a teaching moment rather than a discipline event; coach in the moment; give specific, timely feedback; build the next foreman.
Recognize Team Members for Going Above and Beyond for Safety Recognize the behavior you want repeated — the worker who stopped a lift, reported a near miss, or flagged a bad anchor. Recognition is for leading indicators (Section 1.3), never for injury-free streaks, which suppress reporting.
Safety climate vs. safety culture
These are related but distinct, and FSL is aimed squarely at the first one:
- Definition Timescale
- Safety culture The deep, shared assumptions and values about safety in an organization Years; changes slowly
Safety climate Workers' shared perceptions of how safety is prioritized right now, on this jobsite, by this foreman Immediate; measurable by survey; changes with leadership behavior
CPWR's research finding — the reason FSL exists — is that front-line leader behavior is the strongest single driver of jobsite safety climate , and that a stronger climate produces fewer injuries, better safe-work practices, higher morale, better teamwork, and better productivity and quality. A foreman cannot change corporate culture this quarter. They can change the climate on their crew this morning.
Caution
The connection back to Chapter 8. A weak safety climate is a latent condition in Reason's Swiss Cheese Model (Section 8.4), and it is the mechanism by which normalization of deviance (Section 8.4) spreads. A crew that has learned their foreman does not want to hear about problems will stop reporting them — and the organization loses the near-miss signal it needs.
- 2. The Outreach Program: What the Card Is and Is Not
- Course structure recap
Category Hours Content
Required 14 Introduction to OSHA (1); Managing Safety and Health (2); OSHA Focus Four Hazards (6); Personal Protective Equipment (2); Health Hazards in Construction (2); Stairways and Ladders (1)
Elective 12 At least 6 topics from the list of 15, minimum 30 minutes each (except FSL at 2.5 hours)
Optional 4 Other construction hazards or policies, or expansion of required/elective topics; minimum 30 minutes each
Total 30 Instructional time must be a minimum of 30 hours
Within the required Focus Four block: falls a minimum of 1 hour and 30 minutes , and electrocution, struck-by, and caught-in or between a minimum of 30 minutes each .
The Focus Four learning objectives
The Construction Industry Procedures fix the objectives trainers must use for all Focus Four lessons. Given current OSHA and industry information on construction worksite illnesses, injuries, and fatalities, the student will be able to recognize the hazard, and specifically to:
- Identify major hazards
- Describe types of hazards
- Protect themselves from these hazards
- Recognize employer requirements to protect workers from these hazards
Trainers must not vary from these objectives and must follow the participatory training model .
Ineligible topics
The procedures exclude three categories from counting toward the 30 hours:
- Topics that are not occupational safety and health topics dealing with hazard recognition or prevention
- CPR and First Aid instruction or training
Training conducted to comply with OSHA standards (for example, a required annual respirator fit test or a site-specific lockout procedure)
Caution
The CPR/First Aid exclusion surprises people. First aid is genuinely valuable and is separately required by 1926.50 where medical care is not reasonably accessible — but it cannot be counted toward Outreach hours, because Outreach is a hazard recognition and prevention program.
What the card means
Statement True?
The 30-hour card is an OSHA certification or license No. OSHA does not certify or license workers. The card documents completion of a voluntary Outreach course
The card makes the holder a competent person No. Competent person status under standards such as Subpart P or Subpart L requires knowledge, training, and the authority to take prompt corrective action — a determination the employer makes for a specific hazard
The 30-hour is equivalent to OSHA #510 No. The procedures state directly that the 30-hour construction Outreach class "is not considered equivalent to the OSHA #510 Occupational Safety and Health Standards for the Construction Industry." The 30-hour is a hazard-based class delivered by authorized Outreach trainers; #510 is a standards-based course offered only through OTI Education Centers
Completion satisfies an employer's standard-specific training obligations No. Fall protection training under 1926.503, respirator training under 1910.134(k), silica training under 1926.1153(i), excavation competent person training, and forklift training under 1910.178(l) are all separate obligations
Cards, records, and trainer authorization
Fact Detail
Card expiration Student course completion cards in Construction, General Industry, Maritime, and Disaster Site do not expire under federal OSHA policy. Some states, municipalities, and owners impose their own currency requirements — several jurisdictions require training within the past five years for site access
Reporting a class The Outreach trainer must submit the OSHA Outreach Training Report (OTPR) – Construction to their Authorizing Training Organization (ATO) within 30 days of completing the class
Records retention Outreach trainers must retain program class records for five years from the class end date. This is the trainer's sole responsibility regardless of what the employer keeps
Replacement cards Available only if the class was taken within the last five years (matching the records retention period), and only one replacement per student per class . OSHA does not keep these records and cannot issue replacements — the student must contact the original trainer
Trainer authorization Construction Outreach trainers must complete either the OSHA #502 Update for Construction Industry Outreach Trainers or the OSHA #500 Trainer Course every four years . Expired authorization means the trainer cannot conduct classes or receive student cards, and extensions are not granted
Trainer prerequisite The OSHA #510 course must be completed not later than seven years before completing the OSHA #500 trainer course. Experience cannot be substituted for the training prerequisite and OSHA does not issue waivers
Note
Follow the numbers. #510 is the standards course and the prerequisite. #500 is the trainer course that grants authorization. #502 is the four-year update. The 30-hour Outreach card is what a #500-authorized trainer issues to a student — it is at the other end of the chain entirely.