Study guide

14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F)

OSHA 30-Hour Construction Safety Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety Management, Regulatory Framework & Worker Rights

1.1 OSHA Regulatory Structure, OSH Act, General Duty Clause & Worker Rights 1.2 Safety Management Systems (SMS) & Safety Culture Leadership 1.3 Leading vs. Lagging Indicators, Safety Metrics & Recordkeeping (OSHA 300/300A/301) 1.4 Multi-Employer Worksite Citation Policy & Subcontractor Safety Oversight 1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)

2 Chapter 2: Fall Protection Systems & Working at Heights

2.1 Fall Hazards, 6-Foot Rule & 29 CFR 1926 Subpart M Scope 2.2 Guardrail Systems, Safety Net Systems & Hole Covers 2.3 Personal Fall Arrest Systems (PFAS), Anchorages & Fall Clearance Calculations 2.4 Controlled Access Zones, Safety Monitoring Systems & Leading Edge Work 2.5 Stairways, Ladders & Access Systems (29 CFR 1926 Subpart X)

3 Chapter 3: Electrical Safety, Grounding & Energy Control

3.1 Electrical Hazards, Electrocution Dynamics & 29 CFR 1926 Subpart K 3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP) 3.3 Overhead Power Line Clearances & Encroachment Prevention 3.4 Lockout/Tagout (LOTO), De-energization & Hazardous Energy Control 3.5 Arc Flash Hazards, PPE Requirements & Qualified Worker Distinctions

4 Chapter 4: Scaffolding Systems & Aerial Lifts

4.1 Scaffold Classifications, Load Capacities & Subpart L General Requirements 4.2 Supported Scaffolds: Foundations, Planking, Bracing, Tie-ins & Erection 4.3 Suspended Scaffolds, Two-Point Swings & Rigging Counterweights 4.4 Aerial Lifts, Scissor Lifts & Mobile Elevated Work Platforms (MEWPs) 4.5 Competent Person Scaffold Inspection, Fall Protection & Access Rules

5 Chapter 5: Excavation, Trenching & Shoring Safety

5.1 Excavation Hazards, Soil Mechanics & Subpart P Scope 5.2 OSHA Soil Classification: Visual and Manual Field Testing (Types A, B, C) 5.3 Protective Systems: Sloping and Benching Ratios 5.4 Protective Systems: Hydraulic Shoring, Trench Boxes & Shields 5.5 Excavation Access/Egress, Hazardous Atmospheres & Competent Person Daily Inspections

6 Chapter 6: Cranes, Derricks, Hoists & Rigging

6.1 Subpart CC Scope, Operator Certification & Qualification Requirements 6.2 Crane Setup, Ground Conditions, Outriggers & Power Line Safety 6.3 Load Charts, Capacity Calculations & Lift Planning 6.4 Critical Lift Planning, Tandem Lifts & Personnel Hoisting 6.5 Rigging Hardware, Sling Angles, Hitches & Signal Person Qualifications

7 Chapter 7: Confined Spaces in Construction

7.1 29 CFR 1926 Subpart AA Scope & Confined Space vs. Permit-Required Confined Space (PRCS) 7.2 Atmospheric Testing: Sequential Order (O2, Flammability, Toxicity) & Calibration 7.3 PRCS Entry Permit Program, Isolation & Ventilation 7.4 Duties of Authorized Entrants, Attendants & Entry Supervisors 7.5 Non-Entry vs. Entry Rescue, Emergency Services & Retrieval Systems

8 Chapter 8: Incident Investigation, Root Cause Analysis & Prevention

8.1 Purpose of Incident Investigation & Blame-Free Reporting Culture 8.2 Immediate Response, Scene Security, Evidence Gathering & Witness Interviewing 8.3 Root Cause Analysis Methodologies: 5 Whys, Fishbone (Ishikawa), and Fault Tree 8.4 Human Factors, Swiss Cheese Model & Latent Organizational Failures 8.5 Corrective Action Plans, Hierarchy of Controls Application & Near-Miss Trending

9 Chapter 9: Occupational Health Hazards & Environmental Protection

9.1 Hazard Communication Standard (HazCom 2012 / GHS) & 16-Section Safety Data Sheets (SDSs) 9.2 Respirable Crystalline Silica (29 CFR 1926.1153) & Table 1 Control Methods 9.3 Lead & Asbestos Hazards in Construction Demolition and Renovation (29 CFR 1926.62 / 1926.1101) 9.4 Occupational Noise Exposure, Action Levels, PELs & Hearing Conservation Programs (Subpart D) 9.5 Thermal Stress (Heat Illness & Cold Injury Prevention) & Biological/Chemical Hazards

10 Chapter 10: Ergonomics, Material Handling & Tool Safety

10.1 Ergonomic Risk Factors in Construction & Musculoskeletal Disorders (MSDs) 10.2 Manual Material Handling, Safe Lifting Principles & Ergonomic Engineering Solutions 10.3 Hand-Arm Vibration Syndrome (HAVS), Whole-Body Vibration & Power Tool Safety (Subpart I) 10.4 Material Storage, Rigging Safety, Housekeeping & Disposal (29 CFR 1926 Subpart H) 10.5 Motor Vehicles, Heavy Equipment, Highway Work Zone Safety & Struck-By Prevention (Subpart O/G)

11 Chapter 11: Personal Protective and Life-Saving Equipment (29 CFR 1926 Subpart E)

11.1 PPE Programs, Hazard Assessment, the Proper-Fit Rule & Employer Payment 11.2 Head, Eye, and Face Protection (1926.100 / 1926.102) 11.3 Hearing, Hand, Foot, and Body Protection (1926.101 / 1926.95 / 1926.96) 11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing (1926.103)

12 Chapter 12: Struck-By and Caught-In/Between Focus Four Hazards

12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects 12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection 12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts (1926.602)

13 Chapter 13: Concrete, Masonry & Steel Erection (Subparts Q and R)

13.1 Cast-in-Place Concrete, Formwork, Shoring & Rebar Impalement (Subpart Q) 13.2 Masonry Construction, Limited Access Zones & Precast/Tilt-Up Panels (Subpart Q) 13.3 Steel Erection: Column Anchorage, Connectors, Decking & the CDZ (Subpart R)

14 Chapter 14: Fire Prevention, Welding & Cutting, and Demolition (Subparts F, J, T)

14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F) 14.2 Welding, Cutting & Hot Work (29 CFR 1926 Subpart J) 14.3 Demolition: Engineering Surveys & Sequenced Removal (29 CFR 1926 Subpart T)

15 Chapter 15: Emergency Preparedness, Site Welfare & Safety Leadership

15.1 Emergency Action Plans, Medical Services, First Aid & Sanitation (1926.35 / .50 / .51) 15.2 Foundations for Safety Leadership & the OSHA Outreach Card

14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F)

Key Takeaways Explain This Topic AI

29 CFR 1926.150(c)(1)(i) requires a fire extinguisher rated not less than 2A for each 3,000 square feet of protected building area, with travel distance from any point to the nearest extinguisher not exceeding 100 feet.

A fire extinguisher rated not less than 10B must be provided within 50 feet of any location where more than 5 gallons of flammable or combustible liquid or 5 pounds of flammable gas are in use.

No more than 25 gallons of flammable liquids may be stored in a room outside of an approved storage cabinet (29 CFR 1926.152(b)(3)).

Under 29 CFR 1926.24, the employer is responsible for developing and maintaining an effective fire protection and prevention program throughout all phases of construction, repair, alteration, or demolition.

Extinguisher classes map to fuel type: A for ordinary combustibles, B for flammable liquids and gases, C for energized electrical equipment, and D for combustible metals.

Last updated: November 2026

14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F)

Fire Protection and Prevention is one of the fifteen Elective topics in the OSHA 30-Hour Construction Outreach curriculum, governed by 29 CFR 1926 Subpart F (1926.150 – 1926.155) plus the general duty at 1926.24 .

A construction fire is a different problem from a building fire. The structure has no compartmentation yet, no sprinklers, no functioning alarm, no fire-rated assemblies, and it is full of temporary combustibles: form lumber, foam insulation, tarps, packaging, solvents, propane, and gasoline. The egress paths are unfinished stairs. Firefighters arriving at a mid-rise under construction face a fuel-loaded structure with unknown stability.

1. The Program Duty — 29 CFR 1926.24

"The employer shall be responsible for the development and maintenance of an effective fire protection and prevention program at the job site throughout all phases of the construction, repair, alteration, or demolition work."

"Throughout all phases" is the operative language. Fire risk is not constant: it peaks during framing and rough-in when combustible loading is highest and detection is lowest, then again during finishes when solvents and adhesives arrive.

1926.150(a) adds the operating requirements: firefighting equipment must be provided, must be conspicuously located , must be periodically inspected and maintained in operating condition, and access to all available firefighting equipment shall be maintained at all times . Equipment that is defective or has been used must be immediately replaced or restored to operable condition .

2. Portable Fire Extinguishers — The Testable Math

29 CFR 1926.150(c)(1) contains four numbers that appear on almost every OSHA 30 final exam.

Requirement Value Citation

Extinguisher rating and coverage One 2A-rated extinguisher per 3,000 sq ft of protected building area, or major fraction thereof 1926.150(c)(1)(i)

Maximum travel distance 100 feet from any point in the protected area to the nearest extinguisher 1926.150(c)(1)(i)

Each floor One or more 2A extinguishers on each floor ; in multistory buildings, at least one adjacent to the stairway 1926.150(c)(1)(iv)

Flammable liquid / gas operations One 10B-rated extinguisher within 50 feet wherever more than 5 gallons of flammable or combustible liquid or 5 pounds of flammable gas are being used. Does not apply to integral fuel tanks of motor vehicles 1926.150(c)(1)(vi)

Permitted substitutions for a 2A extinguisher:

One 55-gallon open drum of water with two fire pails (1926.150(c)(1)(ii))

A ½-inch garden-type hose line , not over 100 feet long, with a nozzle, capable of discharging at least 5 gallons per minute with a minimum horizontal stream range of 30 feet (1926.150(c)(1)(iii))

Working the coverage problem

A 12,000 sq ft floor plate requires 12,000 ÷ 3,000 = 4 12{,}000 \div 3{,}000 = \mathbf{4} 12 , 000 ÷ 3 , 000 = 4 extinguishers rated at least 2A on that floor — and they must be placed so no point on the floor is more than 100 feet of travel from one. Four extinguishers clustered at the stair core satisfy the count and fail the travel distance. Both conditions must be met.

Caution

Exam Trap: "major fraction thereof" means you round up . A 7,000 sq ft area needs 3 extinguishers ( 7,000 ÷ 3,000 = 2.33 7{,}000 \div 3{,}000 = 2.33 7 , 000 ÷ 3 , 000 = 2.33 ), not 2.

3. Extinguisher Classes and Use

  • Class Fuel Typical Construction Source
  • A Ordinary combustibles — wood, paper, cloth, most plastics Form lumber, packaging, insulation, tarps
  • B Flammable liquids and gases Gasoline, diesel, solvents, adhesives, propane
  • C Energized electrical equipment Temporary power, generators, panels

D Combustible metals — magnesium, titanium, sodium, lithium Metal fabrication; requires a special dry-powder agent, never water

K Cooking oils and fats Site kitchens and canteens; rare on construction proper

A multipurpose ABC dry chemical extinguisher is the construction default. Note that the C rating means the agent is non-conductive , not that the extinguisher deals with electricity specially — the first action on an electrical fire is still de-energize (Chapter 3).

  • Operating a portable extinguisher — PASS: P ─ PULL the pin (breaking the tamper seal)
  • A ─ AIM low, at the BASE of the fire, not the flames
  • S ─ SQUEEZE the handle to discharge
  • S ─ SWEEP side to side across the base of the fire

Stand 8 to 10 feet back, keep an unobstructed exit at your back , and never fight a fire that is larger than you are, that is spreading, or that has cut off your egress. A typical 10-pound ABC unit discharges in roughly 10 to 25 seconds .

Inspection: portable extinguishers must be inspected periodically and maintained in accordance with the incorporated NFPA maintenance standard (1926.150(c)(1)(viii)); or, alternatively under (c)(1)(ix), they may be inspected monthly .

4. Flammable and Combustible Liquids — 29 CFR 1926.152

OSHA aligned this section with the GHS hazard categories in the 2012 HazCom update. Category 1, 2, and 3 flammable liquids correspond to what the older standards called Class I and II; Category 4 corresponds to Class III.

  • Rule Quantity Citation
  • Only approved containers and portable tanks may be used for storage and handling — 1926.152(a)(1)
  • Flammable liquids must be kept in closed containers when not actually in use — 1926.152(a)(2)
  • Quantity kept in the vicinity of the work operation limited to that required to do the job — 1926.152(b)(2)
  • Maximum stored in a room outside of an approved storage cabinet 25 gallons 1926.152(b)(3)
  • Maximum Category 1, 2, or 3 liquids in any one storage cabinet 60 gallons 1926.152(b)(4)(i)
  • Maximum Category 4 liquids in any one storage cabinet 120 gallons 1926.152(b)(4)(i)
  • Maximum cabinets in a single storage area 3 1926.152(b)(4)(i)
  • Safety cans and dispensing

An approved safety can has a spring-closing lid, a spout cover, and a flame arrester screen , and is designed to relieve internal pressure when exposed to fire. Ordinary buckets, milk jugs, and unlabeled containers are violations on sight.

Bonding and grounding is required when transferring flammable liquids between metal containers. The transfer of liquid generates a static charge ; bonding equalizes potential between the two containers and grounding drains charge to earth. A static spark at the fill point is a classic ignition source. 1926.152(g)(11) also requires that engines be shut off during refueling, except for diesel-powered equipment where the manufacturer permits otherwise.

5. Ignition Sources — 29 CFR 1926.151

Provision Requirement

1926.151(a)(1) Electrical wiring and equipment for light, heat, or power must be installed in compliance with Subpart K

1926.151(a)(2) Internal combustion engine powered equipment must be located so exhausts are well away from combustible materials ; where exhausts are piped outside the building, a clearance of at least 6 inches must be maintained between piping and combustible material

1926.151(a)(3) Smoking must be prohibited at or in the vicinity of operations that constitute a fire hazard, and conspicuously posted: "No Smoking or Open Flame"

1926.151(a)(4) Portable battery-powered lighting used with flammable gases or liquids must be approved for the hazardous location

1926.151(a)(5) Nozzles of air, inert gas, and steam lines used to clean or ventilate tanks containing hazardous concentrations of flammable gases or vapors must be bonded to the tank or vessel shell

1926.151(b) Combustible materials must be piled with due regard to stability and orderly storage; driveways between and around combustible storage piles must be at least 15 feet wide and maintained free of accumulated material

1926.151(c) Portable fire extinguishing equipment suitable for the fire hazard must be provided at convenient, conspicuously accessible locations in the yard area

Temporary heating devices — 1926.154

Temporary heaters are a leading cause of construction fires and of carbon monoxide poisoning during winter work.

Ventilation (1926.154(a)): fresh air must be supplied in sufficient quantities to maintain the health and safety of workers. Where natural means of fresh air supply are inadequate, mechanical ventilation is required.

Clearance (1926.154(b)): heaters must be installed with the clearances to combustible material required by the standard's table, and must be set horizontal and level unless designed otherwise.

Stability (1926.154(c)): heaters used near tarpaulins, canvas, or similar coverings must be located at least 10 feet from the covering, and the covering must be securely fastened to prevent it from igniting or upsetting the heater.

Solid fuel salamanders are prohibited in buildings and on scaffolds (1926.154(d)).

Liquefied petroleum gas heaters: governed by 1926.153, including container placement, valve protection, and quantity limits.

Caution

The carbon monoxide trap. An unvented propane or kerosene heater in a partially enclosed structure produces CO continuously. The OSHA construction PEL is 50 ppm as an 8-hour TWA (Section 5.5), and a salamander in a poly-wrapped floor can pass that within an hour. Ventilation and CO monitoring are not optional cold-weather extras.

6. Fixed Systems and Water Supply

Water supply (1926.150(b)): a temporary or permanent water supply of sufficient volume, duration, and pressure to operate the firefighting equipment must be made available as soon as combustible materials accumulate . Where underground water mains are to be provided, they must be installed, completed, and made available as soon as practicable .

Standpipes (1926.150(d)): in all structures where standpipes are required — or where they exist in structures being altered — they must be brought up as soon as applicable laws permit and maintained as construction progresses so that they are always ready for fire protection use . Standpipes must be provided with Siamese fire department connections on the outside of the structure at street level , conspicuously marked, with valve caps in place.

Fire cutoffs (1926.151(d)): fire walls and exit stairways required for the completed building must be given construction priority , and fire doors with automatic closing devices must be hung on openings as soon as practicable.

Alarms (1926.150(e)(1)): the employer must establish an alarm system, such as a telephone system or siren, that can alert employees on the site and the local fire department for an emergency.