Study guide
11.2 Head, Eye, and Face Protection (1926.100 / 1926.102)
OSHA 30-Hour Construction Safety Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety Management, Regulatory Framework & Worker Rights
1.1 OSHA Regulatory Structure, OSH Act, General Duty Clause & Worker Rights 1.2 Safety Management Systems (SMS) & Safety Culture Leadership 1.3 Leading vs. Lagging Indicators, Safety Metrics & Recordkeeping (OSHA 300/300A/301) 1.4 Multi-Employer Worksite Citation Policy & Subcontractor Safety Oversight 1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)
2 Chapter 2: Fall Protection Systems & Working at Heights
2.1 Fall Hazards, 6-Foot Rule & 29 CFR 1926 Subpart M Scope 2.2 Guardrail Systems, Safety Net Systems & Hole Covers 2.3 Personal Fall Arrest Systems (PFAS), Anchorages & Fall Clearance Calculations 2.4 Controlled Access Zones, Safety Monitoring Systems & Leading Edge Work 2.5 Stairways, Ladders & Access Systems (29 CFR 1926 Subpart X)
3 Chapter 3: Electrical Safety, Grounding & Energy Control
3.1 Electrical Hazards, Electrocution Dynamics & 29 CFR 1926 Subpart K 3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP) 3.3 Overhead Power Line Clearances & Encroachment Prevention 3.4 Lockout/Tagout (LOTO), De-energization & Hazardous Energy Control 3.5 Arc Flash Hazards, PPE Requirements & Qualified Worker Distinctions
4 Chapter 4: Scaffolding Systems & Aerial Lifts
4.1 Scaffold Classifications, Load Capacities & Subpart L General Requirements 4.2 Supported Scaffolds: Foundations, Planking, Bracing, Tie-ins & Erection 4.3 Suspended Scaffolds, Two-Point Swings & Rigging Counterweights 4.4 Aerial Lifts, Scissor Lifts & Mobile Elevated Work Platforms (MEWPs) 4.5 Competent Person Scaffold Inspection, Fall Protection & Access Rules
5 Chapter 5: Excavation, Trenching & Shoring Safety
5.1 Excavation Hazards, Soil Mechanics & Subpart P Scope 5.2 OSHA Soil Classification: Visual and Manual Field Testing (Types A, B, C) 5.3 Protective Systems: Sloping and Benching Ratios 5.4 Protective Systems: Hydraulic Shoring, Trench Boxes & Shields 5.5 Excavation Access/Egress, Hazardous Atmospheres & Competent Person Daily Inspections
6 Chapter 6: Cranes, Derricks, Hoists & Rigging
6.1 Subpart CC Scope, Operator Certification & Qualification Requirements 6.2 Crane Setup, Ground Conditions, Outriggers & Power Line Safety 6.3 Load Charts, Capacity Calculations & Lift Planning 6.4 Critical Lift Planning, Tandem Lifts & Personnel Hoisting 6.5 Rigging Hardware, Sling Angles, Hitches & Signal Person Qualifications
7 Chapter 7: Confined Spaces in Construction
7.1 29 CFR 1926 Subpart AA Scope & Confined Space vs. Permit-Required Confined Space (PRCS) 7.2 Atmospheric Testing: Sequential Order (O2, Flammability, Toxicity) & Calibration 7.3 PRCS Entry Permit Program, Isolation & Ventilation 7.4 Duties of Authorized Entrants, Attendants & Entry Supervisors 7.5 Non-Entry vs. Entry Rescue, Emergency Services & Retrieval Systems
8 Chapter 8: Incident Investigation, Root Cause Analysis & Prevention
8.1 Purpose of Incident Investigation & Blame-Free Reporting Culture 8.2 Immediate Response, Scene Security, Evidence Gathering & Witness Interviewing 8.3 Root Cause Analysis Methodologies: 5 Whys, Fishbone (Ishikawa), and Fault Tree 8.4 Human Factors, Swiss Cheese Model & Latent Organizational Failures 8.5 Corrective Action Plans, Hierarchy of Controls Application & Near-Miss Trending
9 Chapter 9: Occupational Health Hazards & Environmental Protection
9.1 Hazard Communication Standard (HazCom 2012 / GHS) & 16-Section Safety Data Sheets (SDSs) 9.2 Respirable Crystalline Silica (29 CFR 1926.1153) & Table 1 Control Methods 9.3 Lead & Asbestos Hazards in Construction Demolition and Renovation (29 CFR 1926.62 / 1926.1101) 9.4 Occupational Noise Exposure, Action Levels, PELs & Hearing Conservation Programs (Subpart D) 9.5 Thermal Stress (Heat Illness & Cold Injury Prevention) & Biological/Chemical Hazards
10 Chapter 10: Ergonomics, Material Handling & Tool Safety
10.1 Ergonomic Risk Factors in Construction & Musculoskeletal Disorders (MSDs) 10.2 Manual Material Handling, Safe Lifting Principles & Ergonomic Engineering Solutions 10.3 Hand-Arm Vibration Syndrome (HAVS), Whole-Body Vibration & Power Tool Safety (Subpart I) 10.4 Material Storage, Rigging Safety, Housekeeping & Disposal (29 CFR 1926 Subpart H) 10.5 Motor Vehicles, Heavy Equipment, Highway Work Zone Safety & Struck-By Prevention (Subpart O/G)
11 Chapter 11: Personal Protective and Life-Saving Equipment (29 CFR 1926 Subpart E)
11.1 PPE Programs, Hazard Assessment, the Proper-Fit Rule & Employer Payment 11.2 Head, Eye, and Face Protection (1926.100 / 1926.102) 11.3 Hearing, Hand, Foot, and Body Protection (1926.101 / 1926.95 / 1926.96) 11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing (1926.103)
12 Chapter 12: Struck-By and Caught-In/Between Focus Four Hazards
12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects 12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection 12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts (1926.602)
13 Chapter 13: Concrete, Masonry & Steel Erection (Subparts Q and R)
13.1 Cast-in-Place Concrete, Formwork, Shoring & Rebar Impalement (Subpart Q) 13.2 Masonry Construction, Limited Access Zones & Precast/Tilt-Up Panels (Subpart Q) 13.3 Steel Erection: Column Anchorage, Connectors, Decking & the CDZ (Subpart R)
14 Chapter 14: Fire Prevention, Welding & Cutting, and Demolition (Subparts F, J, T)
14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F) 14.2 Welding, Cutting & Hot Work (29 CFR 1926 Subpart J) 14.3 Demolition: Engineering Surveys & Sequenced Removal (29 CFR 1926 Subpart T)
15 Chapter 15: Emergency Preparedness, Site Welfare & Safety Leadership
15.1 Emergency Action Plans, Medical Services, First Aid & Sanitation (1926.35 / .50 / .51) 15.2 Foundations for Safety Leadership & the OSHA Outreach Card
11.2 Head, Eye, and Face Protection (1926.100 / 1926.102)
Key Takeaways Explain This Topic AI
ANSI/ISEA Z89.1 classifies head protection by impact Type — Type I resists top impact only, Type II resists both top and lateral impact — and by electrical Class G (2,200 V), Class E (20,000 V), and Class C (conductive, no electrical protection).
29 CFR 1926.100(b) accepts head protection meeting ANSI Z89.1-2009, Z89.1-2003, or Z89.1-1997, or equipment the employer demonstrates is equally effective.
OSHA Safety and Health Information Bulletin SHIB 11-22-2023 encourages employers to move from traditional hard hats to Type II safety helmets with chin straps, which resist lateral impact and stay on during a fall.
Eye and face protection under 29 CFR 1926.102 must meet ANSI Z87.1 and must include side protection whenever there is a hazard from flying objects.
Welding filter lens shade requirements scale with the process and amperage — shielded metal arc welding above 160 amperes requires a minimum shade of 12 under the Subpart E filter tables.
Last updated: August 2026
- 11.2 Head, Eye, and Face Protection (1926.100 / 1926.102)
- 1. When Head Protection Is Required — 1926.100(a)
"Employees working in areas where there is a possible danger of head injury from impact, or from falling or flying objects, or from electrical shock and burns, shall be protected by protective helmets."
Note the trigger is possible danger , not demonstrated danger. On an active construction site with overhead work, material handling, and energized temporary power, that condition is essentially permanent — which is why 100% hard-hat policies are the industry norm rather than a task-by-task determination.
1926.100(b) accepts head protection that complies with any of three incorporated editions of the consensus standard — ANSI Z89.1-2009, ANSI Z89.1-2003, or ANSI Z89.1-1997 — or head protection the employer demonstrates to be equally effective .
2. Reading the ANSI/ISEA Z89.1 Label
Every compliant helmet carries a label inside the shell with a Type and a Class . Candidates routinely confuse the two.
Impact Type — Where the blow can come from
Type Protects Against Typical Use
Type I Top impact only — a vertical blow to the crown The traditional hard hat. Falling-object protection.
Type II Top impact AND lateral impact — front, back, and side Safety helmets with internal foam liners; work near mobile equipment, at height, or where a fall or side strike is credible.
Electrical Class — How much voltage the shell can take
Class Rating Meaning
Class G (General) Tested to 2,200 volts The default for most general construction.
Class E (Electrical) Tested to 20,000 volts Required for utility work and any task with credible high-voltage contact exposure.
Class C (Conductive) No electrical protection at all Vented shells and aluminum hats. Comfortable, cool — and lethal near energized conductors.
Caution
Exam Trap: the letter C does not stand for "Class C = certified." It stands for Conductive . A vented Class C helmet is legal head protection against falling objects and is completely non-compliant for anyone with electrical exposure. If a scenario places a worker near energized parts, the vented "cooler" helmet is always the wrong answer.
Note
The G/E memory hook: G eneral = 2,200 V, E lectrical = 20,000 V. One order of magnitude apart, and the higher number belongs to the letter that means electrical.
3. The Safety-Helmet Transition (SHIB 11-22-2023)
In November 2023 OSHA issued Safety and Health Information Bulletin 11-22-2023, "Head Protection: Safety Helmets in the Workplace," and announced that OSHA's own field personnel would move from traditional hard hats to safety helmets.
The engineering argument: a traditional Type I hard hat is a suspension system under a shell. It is very good at one thing — absorbing a vertical blow — and poor at everything else. It has no chin strap, so it leaves the head during the tumble phase of a fall. It provides no side impact resistance, which matters because struck-by and fall incidents rarely deliver a clean vertical load.
What a safety helmet adds:
- Type II lateral impact protection from an internal expanded-polystyrene or foam liner
- A chin strap / retention system so the helmet stays on during a fall or a slip
- Frequently, integrated face shields, eye protection, and hearing attachments
- Better weight distribution and, in many designs, improved ventilation without sacrificing the electrical class
Regulatory status: the SHIB is guidance, not a standard . 1926.100 still permits a compliant Type I Class G hard hat. But OSHA explicitly recommends safety helmets for workers at height, near mobile equipment, near electrical hazards, in high-temperature environments, and doing specialized work such as high-voltage or oil-and-gas tasks. Expect exam items that ask which document drives the transition (the SHIB) and whether hard hats are now prohibited (they are not).
4. Inspection, Service Life, and Field Abuse
- Condition Action
- Cracks, gouges, penetration, or a chalky/dull shell surface (UV degradation) Remove from service
- Any impact — even with no visible damage Remove from service; the energy-absorbing structure is single-use
- Suspension frayed, cracked, or with broken keys Replace suspension
Drilled holes, or stickers covering enough shell to hide cracks Non-compliant — drilling voids the electrical class entirely
Painted with solvent-based paint, or cleaned with solvents Non-compliant — solvents attack the thermoplastic shell
Worn backward Only permitted if the manufacturer specifically certifies reverse-wear (many suspensions are marked for it)
Manufacturers commonly specify shell replacement at 5 years from date of manufacture and suspension replacement at 12 months , but the governing document is always the manufacturer's instruction , not a generic rule of thumb.
5. Eye and Face Protection — 1926.102
"Employees shall be provided with eye and face protection equipment when machines or operations present potential eye or face injury from physical, chemical, or radiation agents."
1926.102(a)(2) requires the equipment to meet ANSI Z87.1 (the standard incorporates the 2010, 2003, and 1989(R-1998) editions). Compliant lenses are permanently marked Z87 or Z87+ (the plus indicates high-impact rated).
Side Protection Is Not Optional
Where there is a hazard from flying objects , the standard requires eye protection with side protection . Detachable side shields are acceptable if they meet the requirement. Ordinary prescription glasses do not qualify — the worker needs either prescription safety eyewear meeting Z87.1 or goggles/over-the-glass protectors worn over their own lenses.
Selecting for the Hazard
Hazard Minimum Protection
Flying particles (grinding, chipping, nailing, sawing) Z87+ safety glasses with side protection ; face shield over glasses for high-energy grinding
Chemical splash (concrete slurry, solvents, acids) Indirectly vented or non-vented goggles ; face shield adds splash coverage but never replaces goggles
- Dust Non-vented or indirectly vented goggles
- Optical radiation (welding, cutting, brazing) Filter lens of the correct shade number
Caution
A face shield is always secondary protection. It is worn over primary eye protection, never instead of it. A scenario in which a worker performs abrasive cutting wearing only a face shield is a violation regardless of how substantial the shield is.
Welding Filter Shades
Subpart E incorporates filter-lens shade tables keyed to the process and current. The values candidates are expected to know:
- Operation Minimum Protective Shade
- Torch soldering 2
- Torch brazing 3
- Oxygen cutting, light (under 1 inch) 3
- Gas welding, light (under 1/8 inch) 4
- Shielded metal arc welding, 1/8- to 5/32-inch electrodes 10
- Shielded metal arc welding, over 5/32-inch electrodes / above 160 amperes 12
- Atomic hydrogen welding / carbon arc welding 14 (the darkest common shade)
Helpers and bystanders need protection too. The flash burn ("arc eye") that sends a worker to urgent care is usually not the welder — it is the pipefitter twenty feet away with no screen and no shaded lens. Screens and shields around the arc are part of the eye-protection answer, not a separate courtesy.