Study guide

11.3 Hearing, Hand, Foot, and Body Protection (1926.101 / 1926.95 / 1926.96)

OSHA 30-Hour Construction Safety Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety Management, Regulatory Framework & Worker Rights

1.1 OSHA Regulatory Structure, OSH Act, General Duty Clause & Worker Rights 1.2 Safety Management Systems (SMS) & Safety Culture Leadership 1.3 Leading vs. Lagging Indicators, Safety Metrics & Recordkeeping (OSHA 300/300A/301) 1.4 Multi-Employer Worksite Citation Policy & Subcontractor Safety Oversight 1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)

2 Chapter 2: Fall Protection Systems & Working at Heights

2.1 Fall Hazards, 6-Foot Rule & 29 CFR 1926 Subpart M Scope 2.2 Guardrail Systems, Safety Net Systems & Hole Covers 2.3 Personal Fall Arrest Systems (PFAS), Anchorages & Fall Clearance Calculations 2.4 Controlled Access Zones, Safety Monitoring Systems & Leading Edge Work 2.5 Stairways, Ladders & Access Systems (29 CFR 1926 Subpart X)

3 Chapter 3: Electrical Safety, Grounding & Energy Control

3.1 Electrical Hazards, Electrocution Dynamics & 29 CFR 1926 Subpart K 3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP) 3.3 Overhead Power Line Clearances & Encroachment Prevention 3.4 Lockout/Tagout (LOTO), De-energization & Hazardous Energy Control 3.5 Arc Flash Hazards, PPE Requirements & Qualified Worker Distinctions

4 Chapter 4: Scaffolding Systems & Aerial Lifts

4.1 Scaffold Classifications, Load Capacities & Subpart L General Requirements 4.2 Supported Scaffolds: Foundations, Planking, Bracing, Tie-ins & Erection 4.3 Suspended Scaffolds, Two-Point Swings & Rigging Counterweights 4.4 Aerial Lifts, Scissor Lifts & Mobile Elevated Work Platforms (MEWPs) 4.5 Competent Person Scaffold Inspection, Fall Protection & Access Rules

5 Chapter 5: Excavation, Trenching & Shoring Safety

5.1 Excavation Hazards, Soil Mechanics & Subpart P Scope 5.2 OSHA Soil Classification: Visual and Manual Field Testing (Types A, B, C) 5.3 Protective Systems: Sloping and Benching Ratios 5.4 Protective Systems: Hydraulic Shoring, Trench Boxes & Shields 5.5 Excavation Access/Egress, Hazardous Atmospheres & Competent Person Daily Inspections

6 Chapter 6: Cranes, Derricks, Hoists & Rigging

6.1 Subpart CC Scope, Operator Certification & Qualification Requirements 6.2 Crane Setup, Ground Conditions, Outriggers & Power Line Safety 6.3 Load Charts, Capacity Calculations & Lift Planning 6.4 Critical Lift Planning, Tandem Lifts & Personnel Hoisting 6.5 Rigging Hardware, Sling Angles, Hitches & Signal Person Qualifications

7 Chapter 7: Confined Spaces in Construction

7.1 29 CFR 1926 Subpart AA Scope & Confined Space vs. Permit-Required Confined Space (PRCS) 7.2 Atmospheric Testing: Sequential Order (O2, Flammability, Toxicity) & Calibration 7.3 PRCS Entry Permit Program, Isolation & Ventilation 7.4 Duties of Authorized Entrants, Attendants & Entry Supervisors 7.5 Non-Entry vs. Entry Rescue, Emergency Services & Retrieval Systems

8 Chapter 8: Incident Investigation, Root Cause Analysis & Prevention

8.1 Purpose of Incident Investigation & Blame-Free Reporting Culture 8.2 Immediate Response, Scene Security, Evidence Gathering & Witness Interviewing 8.3 Root Cause Analysis Methodologies: 5 Whys, Fishbone (Ishikawa), and Fault Tree 8.4 Human Factors, Swiss Cheese Model & Latent Organizational Failures 8.5 Corrective Action Plans, Hierarchy of Controls Application & Near-Miss Trending

9 Chapter 9: Occupational Health Hazards & Environmental Protection

9.1 Hazard Communication Standard (HazCom 2012 / GHS) & 16-Section Safety Data Sheets (SDSs) 9.2 Respirable Crystalline Silica (29 CFR 1926.1153) & Table 1 Control Methods 9.3 Lead & Asbestos Hazards in Construction Demolition and Renovation (29 CFR 1926.62 / 1926.1101) 9.4 Occupational Noise Exposure, Action Levels, PELs & Hearing Conservation Programs (Subpart D) 9.5 Thermal Stress (Heat Illness & Cold Injury Prevention) & Biological/Chemical Hazards

10 Chapter 10: Ergonomics, Material Handling & Tool Safety

10.1 Ergonomic Risk Factors in Construction & Musculoskeletal Disorders (MSDs) 10.2 Manual Material Handling, Safe Lifting Principles & Ergonomic Engineering Solutions 10.3 Hand-Arm Vibration Syndrome (HAVS), Whole-Body Vibration & Power Tool Safety (Subpart I) 10.4 Material Storage, Rigging Safety, Housekeeping & Disposal (29 CFR 1926 Subpart H) 10.5 Motor Vehicles, Heavy Equipment, Highway Work Zone Safety & Struck-By Prevention (Subpart O/G)

11 Chapter 11: Personal Protective and Life-Saving Equipment (29 CFR 1926 Subpart E)

11.1 PPE Programs, Hazard Assessment, the Proper-Fit Rule & Employer Payment 11.2 Head, Eye, and Face Protection (1926.100 / 1926.102) 11.3 Hearing, Hand, Foot, and Body Protection (1926.101 / 1926.95 / 1926.96) 11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing (1926.103)

12 Chapter 12: Struck-By and Caught-In/Between Focus Four Hazards

12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects 12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection 12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts (1926.602)

13 Chapter 13: Concrete, Masonry & Steel Erection (Subparts Q and R)

13.1 Cast-in-Place Concrete, Formwork, Shoring & Rebar Impalement (Subpart Q) 13.2 Masonry Construction, Limited Access Zones & Precast/Tilt-Up Panels (Subpart Q) 13.3 Steel Erection: Column Anchorage, Connectors, Decking & the CDZ (Subpart R)

14 Chapter 14: Fire Prevention, Welding & Cutting, and Demolition (Subparts F, J, T)

14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F) 14.2 Welding, Cutting & Hot Work (29 CFR 1926 Subpart J) 14.3 Demolition: Engineering Surveys & Sequenced Removal (29 CFR 1926 Subpart T)

15 Chapter 15: Emergency Preparedness, Site Welfare & Safety Leadership

15.1 Emergency Action Plans, Medical Services, First Aid & Sanitation (1926.35 / .50 / .51) 15.2 Foundations for Safety Leadership & the OSHA Outreach Card

11.3 Hearing, Hand, Foot, and Body Protection (1926.101 / 1926.95 / 1926.96)

Key Takeaways Explain This Topic AI

29 CFR 1926.101 requires hearing protective devices to be fitted or determined individually by a competent person, and plain cotton is expressly not an acceptable protector.

Foot protection under 29 CFR 1926.96 must meet the incorporated safety-toe footwear standard; modern compliant footwear is marked to ASTM F2412/F2413 with ratings such as I/75 impact and C/75 compression.

Glove selection is hazard-specific — cut-resistant ANSI/ISEA 105 levels A1 through A9 address lacerations but provide no chemical breakthrough protection, which is governed by the SDS Section 8 material and breakthrough time.

High-visibility apparel in federal-aid highway work zones is required by 23 CFR 634 and must meet ANSI/ISEA 107, with Class 3 garments used for night work and high-speed traffic exposure.

Rings, loose sleeves, dangling lanyards, and long unrestrained hair are caught-in/between hazards around rotating equipment and must be controlled as part of the body-protection assessment.

Last updated: August 2026

  • 11.3 Hearing, Hand, Foot, and Body Protection
  • 1. Hearing Protection — 1926.101

Section 9.4 covered the exposure limits: the 90 dBA 8-hour PEL in Table D-2 of 1926.52, the 85 dBA action level , and the 5 dB exchange rate . Subpart E covers the device itself.

1926.101(a): "Wherever it is not feasible to reduce the noise levels or duration of exposures to those specified in Table D-2 ... ear protective devices shall be provided and used."

1926.101(b): "Ear protective devices inserted in the ear shall be fitted or determined individually by a competent person."

1926.101(c): "Plain cotton is not an acceptable protective device."

That last sentence is a genuine exam item. Cotton balls, rolled tissue, and shop rags are not hearing protection, and the standard says so in one sentence.

Derating the NRR

Every protector carries a manufacturer Noise Reduction Rating (NRR) established in a laboratory with an expert fitting. The field never reproduces that. OSHA's derating method for comparing protected exposure to an A-weighted TWA is: Estimated Exposure (dBA) = TWA (dBA) − NRR − 7 2 \text{Estimated Exposure (dBA)} = \text{TWA (dBA)} - \frac{\text{NRR} - 7}{2} Estimated Exposure (dBA) = TWA (dBA) − 2 NRR − 7 ​

The subtraction of 7 converts from the C-weighted basis of the NRR test to A-weighting; the division by 2 is OSHA's 50% safety factor for real-world fit. A worker at 100 dBA with an NRR 29 plug is estimated at 100 − ( 29 − 7 ) / 2 = 100 − 11 = 89 100 - (29-7)/2 = 100 - 11 = 89 100 − ( 29 − 7 ) /2 = 100 − 11 = 89 dBA — still above the action level, which is why dual protection (plugs and muffs) is used for the loudest tasks. Dual protection does not add the two NRRs; the accepted convention is to add 5 dB to the higher-rated device's NRR.

Selection realities

Device Strengths Weaknesses

Foam roll-down plugs Highest NRRs; cheap; good for sustained noise Fit-dependent; poor with dirty hands; removed and reinserted improperly

  • Pre-molded / flanged plugs Reusable; washable; consistent fit Lower NRR; require correct size
  • Banded / canal caps Fast on and off for intermittent noise Lowest attenuation; do not seat deeply

Earmuffs Consistent, fit-independent attenuation; easy to verify visually Heat; interfere with helmets and eyewear; broken seals lose attenuation

Note

A muff seal broken by eyewear temple arms is the most common silent failure in construction. Thin-temple safety glasses or muffs with cutouts exist precisely for this.

2. Foot Protection — 1926.96

1926.96: "Safety-toe footwear for employees shall meet the requirements and specifications in American National Standard for Men's Safety-Toe Footwear, Z41.1-1967."

Z41 was withdrawn and replaced by the ASTM standards F2412 (test methods) and F2413 (performance requirements) . OSHA accepts footwear meeting the current ASTM standards as equally effective; the compliant boot carries an ASTM marking inside the tongue.

  • Reading the ASTM F2413 marking ASTM F2413-18 M I/75 C/75 EH
  • │ │ │ │ │
  • │ │ │ │ └─ Electrical Hazard resistance
  • │ │ │ └─────── Compression, 2,500 lbf class
  • │ │ └────────────── Impact, 75 ft-lb class
  • │ └──────────────────── M = Male last (F = Female)
  • └─────────────────────────────── Standard and revision year
  • Marking Protection
  • I/75, C/75 The standard construction rating — 75 ft-lb impact, 2,500 lbf compression
  • PR Puncture resistance — a plate in the sole against nails and rebar

EH Electrical Hazard — secondary protection against incidental contact with energized conductors on dry surfaces

  • SD Static Dissipative — bleeds off static in flammable atmospheres
  • CD Conductive — deliberately grounds the wearer (explosives work). Never for electrical exposure
  • Mt Metatarsal guard — protects the instep from drops that a toe cap misses

Caution

Two traps here. First, EH and CD are opposites : EH insulates, CD grounds. Second, a steel toe is not puncture resistance. A worker who steps on an upturned form nail is protected only by a PR -marked sole. On demolition and forming work, PR is the rating that matters, and the toe cap is incidental.

Recall from Section 11.1 that non-specialty safety-toe footwear is the one footwear category the employee may fund, and only when the employer permits it off site. Metatarsal boots and dielectric footwear are specialty items — employer pays.

3. Hand Protection

Hands are the single most-injured body part in construction. There is no dedicated construction hand-protection section; the duty flows from 1926.95(a) plus the substance-specific standards.

Cut resistance — ANSI/ISEA 105

The cut-resistance scale runs A1 through A9 , measured in grams of load required to cut through the material at a fixed blade travel.

  • Level Grams to Cut Typical Construction Task
  • A1–A2 200–999 g General material handling, light assembly
  • A3–A4 1,000–1,999 g Sheet metal light gauge, glazing prep, framing
  • A5–A6 2,200–2,999 g Sheet metal, glass handling, demolition
  • A7–A9 3,000 g and above Heavy glass, plate steel, extreme laceration exposure

Caution

Cut resistance is not puncture resistance and not chemical resistance. An A6 glove will stop a utility blade and do nothing against a needle, a rebar tie wire, or a caustic. Concrete workers face a chemical hazard — wet portland cement is strongly alkaline and causes third-degree chemical burns through prolonged skin contact — so the correct glove is a nitrile or neoprene chemical glove, not a cut-resistant knit.

Chemical resistance

Select from Section 8 of the Safety Data Sheet (Exposure Controls / Personal Protection — see Section 9.1), which names the recommended glove material. The two variables are material compatibility and breakthrough time . Latex, nitrile, neoprene, butyl, and Viton each resist a different chemical family; a nitrile glove that resists solvents may fail in minutes against a ketone.

Vibration and impact

Anti-vibration gloves meeting ISO 10819 reduce hand-arm vibration transmission and are part of the HAVS control strategy in Section 10.3. Impact-rated gloves with thermoplastic rubber on the back of the hand address the pinch and back-of-hand strikes that dominate hand injuries on pipe, steel, and drilling work.

Note

Rings are a hand hazard, not a hand protector. Degloving injuries occur when a ring catches on a form, a ladder rung, or a rotating shaft. Ring removal is a standard site rule for exactly this reason.

4. Body Protection and High-Visibility Apparel

Hazard Body Protection

Traffic / mobile equipment exposure ANSI/ISEA 107 high-visibility apparel. Class 2 for daytime work under 50 mph; Class 3 (sleeves required, largest background area) for night work, high-speed roadways, and flagging

Arc flash Arc-rated clothing with an arc rating in cal/cm² at or above the incident energy — see Section 3.5. Meltable synthetics (polyester, nylon) are prohibited as they ignite and adhere to skin

  • Welding Flame-resistant leathers, aprons, sleeves; no cuffs; no synthetic under-layers
  • Chemical Coveralls selected by permeation data from SDS Section 8
  • Heat Light-colored, loose, breathable, moisture-wicking — cooling vests where the WBGT warrants (Section 9.5)

Entanglement No loose sleeves, no dangling ID lanyards near rotating equipment, long hair tied back and contained

High-visibility apparel in highway work is a legal requirement, not a preference. For all workers exposed to public traffic in the right-of-way of a federal-aid highway , 23 CFR 634 requires high-visibility safety apparel meeting ANSI/ISEA 107 Performance Class 2 or 3 . In the flagger position, or at night, Class 3 is the practical minimum.