Study guide

11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing (1926.103)

OSHA 30-Hour Construction Safety Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety Management, Regulatory Framework & Worker Rights

1.1 OSHA Regulatory Structure, OSH Act, General Duty Clause & Worker Rights 1.2 Safety Management Systems (SMS) & Safety Culture Leadership 1.3 Leading vs. Lagging Indicators, Safety Metrics & Recordkeeping (OSHA 300/300A/301) 1.4 Multi-Employer Worksite Citation Policy & Subcontractor Safety Oversight 1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)

2 Chapter 2: Fall Protection Systems & Working at Heights

2.1 Fall Hazards, 6-Foot Rule & 29 CFR 1926 Subpart M Scope 2.2 Guardrail Systems, Safety Net Systems & Hole Covers 2.3 Personal Fall Arrest Systems (PFAS), Anchorages & Fall Clearance Calculations 2.4 Controlled Access Zones, Safety Monitoring Systems & Leading Edge Work 2.5 Stairways, Ladders & Access Systems (29 CFR 1926 Subpart X)

3 Chapter 3: Electrical Safety, Grounding & Energy Control

3.1 Electrical Hazards, Electrocution Dynamics & 29 CFR 1926 Subpart K 3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP) 3.3 Overhead Power Line Clearances & Encroachment Prevention 3.4 Lockout/Tagout (LOTO), De-energization & Hazardous Energy Control 3.5 Arc Flash Hazards, PPE Requirements & Qualified Worker Distinctions

4 Chapter 4: Scaffolding Systems & Aerial Lifts

4.1 Scaffold Classifications, Load Capacities & Subpart L General Requirements 4.2 Supported Scaffolds: Foundations, Planking, Bracing, Tie-ins & Erection 4.3 Suspended Scaffolds, Two-Point Swings & Rigging Counterweights 4.4 Aerial Lifts, Scissor Lifts & Mobile Elevated Work Platforms (MEWPs) 4.5 Competent Person Scaffold Inspection, Fall Protection & Access Rules

5 Chapter 5: Excavation, Trenching & Shoring Safety

5.1 Excavation Hazards, Soil Mechanics & Subpart P Scope 5.2 OSHA Soil Classification: Visual and Manual Field Testing (Types A, B, C) 5.3 Protective Systems: Sloping and Benching Ratios 5.4 Protective Systems: Hydraulic Shoring, Trench Boxes & Shields 5.5 Excavation Access/Egress, Hazardous Atmospheres & Competent Person Daily Inspections

6 Chapter 6: Cranes, Derricks, Hoists & Rigging

6.1 Subpart CC Scope, Operator Certification & Qualification Requirements 6.2 Crane Setup, Ground Conditions, Outriggers & Power Line Safety 6.3 Load Charts, Capacity Calculations & Lift Planning 6.4 Critical Lift Planning, Tandem Lifts & Personnel Hoisting 6.5 Rigging Hardware, Sling Angles, Hitches & Signal Person Qualifications

7 Chapter 7: Confined Spaces in Construction

7.1 29 CFR 1926 Subpart AA Scope & Confined Space vs. Permit-Required Confined Space (PRCS) 7.2 Atmospheric Testing: Sequential Order (O2, Flammability, Toxicity) & Calibration 7.3 PRCS Entry Permit Program, Isolation & Ventilation 7.4 Duties of Authorized Entrants, Attendants & Entry Supervisors 7.5 Non-Entry vs. Entry Rescue, Emergency Services & Retrieval Systems

8 Chapter 8: Incident Investigation, Root Cause Analysis & Prevention

8.1 Purpose of Incident Investigation & Blame-Free Reporting Culture 8.2 Immediate Response, Scene Security, Evidence Gathering & Witness Interviewing 8.3 Root Cause Analysis Methodologies: 5 Whys, Fishbone (Ishikawa), and Fault Tree 8.4 Human Factors, Swiss Cheese Model & Latent Organizational Failures 8.5 Corrective Action Plans, Hierarchy of Controls Application & Near-Miss Trending

9 Chapter 9: Occupational Health Hazards & Environmental Protection

9.1 Hazard Communication Standard (HazCom 2012 / GHS) & 16-Section Safety Data Sheets (SDSs) 9.2 Respirable Crystalline Silica (29 CFR 1926.1153) & Table 1 Control Methods 9.3 Lead & Asbestos Hazards in Construction Demolition and Renovation (29 CFR 1926.62 / 1926.1101) 9.4 Occupational Noise Exposure, Action Levels, PELs & Hearing Conservation Programs (Subpart D) 9.5 Thermal Stress (Heat Illness & Cold Injury Prevention) & Biological/Chemical Hazards

10 Chapter 10: Ergonomics, Material Handling & Tool Safety

10.1 Ergonomic Risk Factors in Construction & Musculoskeletal Disorders (MSDs) 10.2 Manual Material Handling, Safe Lifting Principles & Ergonomic Engineering Solutions 10.3 Hand-Arm Vibration Syndrome (HAVS), Whole-Body Vibration & Power Tool Safety (Subpart I) 10.4 Material Storage, Rigging Safety, Housekeeping & Disposal (29 CFR 1926 Subpart H) 10.5 Motor Vehicles, Heavy Equipment, Highway Work Zone Safety & Struck-By Prevention (Subpart O/G)

11 Chapter 11: Personal Protective and Life-Saving Equipment (29 CFR 1926 Subpart E)

11.1 PPE Programs, Hazard Assessment, the Proper-Fit Rule & Employer Payment 11.2 Head, Eye, and Face Protection (1926.100 / 1926.102) 11.3 Hearing, Hand, Foot, and Body Protection (1926.101 / 1926.95 / 1926.96) 11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing (1926.103)

12 Chapter 12: Struck-By and Caught-In/Between Focus Four Hazards

12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects 12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection 12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts (1926.602)

13 Chapter 13: Concrete, Masonry & Steel Erection (Subparts Q and R)

13.1 Cast-in-Place Concrete, Formwork, Shoring & Rebar Impalement (Subpart Q) 13.2 Masonry Construction, Limited Access Zones & Precast/Tilt-Up Panels (Subpart Q) 13.3 Steel Erection: Column Anchorage, Connectors, Decking & the CDZ (Subpart R)

14 Chapter 14: Fire Prevention, Welding & Cutting, and Demolition (Subparts F, J, T)

14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F) 14.2 Welding, Cutting & Hot Work (29 CFR 1926 Subpart J) 14.3 Demolition: Engineering Surveys & Sequenced Removal (29 CFR 1926 Subpart T)

15 Chapter 15: Emergency Preparedness, Site Welfare & Safety Leadership

15.1 Emergency Action Plans, Medical Services, First Aid & Sanitation (1926.35 / .50 / .51) 15.2 Foundations for Safety Leadership & the OSHA Outreach Card

11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing (1926.103)

Key Takeaways Explain This Topic AI

29 CFR 1926.103 states that the respiratory protection requirements applicable to construction are identical to those set forth at 29 CFR 1910.134.

The mandatory sequence is medical evaluation first, then fit testing, then use — a worker may never be fit tested before medical clearance.

Fit testing is required before initial use, whenever a different respirator facepiece is used, and at least annually thereafter.

Assigned Protection Factors set the ceiling on use: filtering facepiece and half-mask air-purifying respirators have an APF of 10, full-facepiece air-purifying respirators 50, loose-fitting PAPRs 25, and pressure-demand SCBA 10,000.

Any facial hair that comes between the sealing surface and the face, or that interferes with valve function, disqualifies a worker from wearing a tight-fitting respirator (1910.134(g)(1)(i)).

Last updated: August 2026

11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing

29 CFR 1926.103 is one sentence of substance: "The requirements applicable to construction work under this section are identical to those set forth at § 1910.134 of this chapter." Everything that follows is 1910.134, applied to a construction site.

Respiratory protection is where Subpart E collides with Chapter 9. Silica Table 1 (Section 9.2) assigns respirators by task and duration. Lead (1926.62) and asbestos (1926.1101) each mandate respirators at defined exposures. Confined space entry (Chapter 7) may require supplied air. All of it runs through 1910.134.

1. The Written Program — 1910.134(c)

Whenever respirators are required , the employer must establish and implement a written respiratory protection program with worksite-specific procedures, administered by a suitably trained program administrator . The program must address:

  • Respirator selection
  • Medical evaluation of employees required to use respirators
  • Fit testing procedures for tight-fitting respirators
  • Procedures for routine use and for emergency/IDLH situations
  • Cleaning, disinfecting, storage, inspection, repair, discarding
  • Ensuring adequate air quality, quantity, and flow for supplied-air respirators
  • Training on respiratory hazards and on proper use, donning, doffing, and limitations
  • Procedures for evaluating program effectiveness

The program is provided at no cost to the employee — including the medical evaluation and the fit test.

2. The Mandatory Sequence

This order is tested constantly, and reversing it is the classic wrong answer. ┌──────────────────────┐ ┌──────────────┐ ┌───────────┐ ┌─────┐

  • │ 1. MEDICAL EVALUATION│───►│ 2. FIT TEST │───►│ 3. TRAIN │───►│ USE │
  • │ (before fit test │ │ (annually, │ │ │ │ │
  • │ or any use) │ │ thereafter)│ │ │ │ │
  • └──────────────────────┘ └──────────────┘ └───────────┘ └─────┘
  • Medical Evaluation — 1910.134(e)

A respirator imposes physiological burden: breathing resistance, dead space, heat load, weight, and — for full facepieces — restricted vision and claustrophobia. The employer must provide a medical evaluation before the employee is fit tested or required to use the respirator in the workplace .

Performed by a physician or other licensed health care professional (PLHCP)

Uses the mandatory medical questionnaire in Appendix C of 1910.134, or an initial medical exam obtaining the same information

The questionnaire is administered confidentially , during working hours or at a convenient time and place, and the employee must have the opportunity to discuss results with the PLHCP

The employer receives only a written recommendation — whether the employee is medically able to use the respirator, any limitations, the need for follow-up, and a statement that the employee was informed of the results. The employer does not receive the medical records themselves.

Additional evaluations are required when an employee reports medical signs or symptoms, when the PLHCP or program administrator recommends it, when fit-test or program observations indicate a need, or when workplace conditions change in a way that increases physiological burden.

Fit Testing — 1910.134(f)

Every employee using a tight-fitting facepiece (filtering facepiece, half mask, or full facepiece) must be fit tested:

  • Before initial use
  • Whenever a different respirator facepiece is used (different size, model, style, or make)
  • At least annually thereafter

Additionally , whenever the employee or the employer observes changes in physical condition affecting fit — weight change, significant facial scarring, dental changes, cosmetic surgery

Method How It Works Limit

QLFT (Qualitative) Pass/fail on the wearer's subjective detection of a test agent — isoamyl acetate (banana oil), saccharin, Bitrex, or irritant smoke Only valid for respirators with APF of 10 or less

QNFT (Quantitative) Instrument measures a numerical fit factor by comparing ambient to in-mask particle concentration Required for any tight-fitting respirator relied on above APF 10. Minimum passing fit factor: 100 for half masks, 500 for full facepieces

Caution

Fit testing is not the same as a user seal check. A user seal check (positive and negative pressure) is performed by the wearer every single time the respirator is donned. A fit test is a formal annual procedure. A scenario in which a worker "did a seal check last year" is confusing the two.

The Facial Hair Rule — 1910.134(g)(1)(i)

The employer must not permit respirators with tight-fitting facepieces to be worn by employees who have:

Facial hair that comes between the sealing surface of the facepiece and the face , or that interferes with valve function ; or

Any condition that interferes with the face-to-facepiece seal or valve function.

This is not a grooming preference — a stubble field measured in days defeats the seal, and the fit test will not pass. Where a worker cannot or will not shave, the compliant path is a loose-fitting powered air-purifying respirator (PAPR) hood or helmet , which requires no face seal.

Corrective glasses, goggles, or other PPE must be worn so they do not interfere with the seal — which is why full-facepiece respirators accept a spectacle kit mounted inside the lens rather than temple arms crossing the seal.

3. Assigned Protection Factors — 1910.134(d)(3)(i)(A)

The Assigned Protection Factor (APF) is the workplace level of respiratory protection a properly functioning respirator is expected to provide. It answers: by what factor does this respirator reduce the concentration reaching the wearer?

  • Respirator Type APF
  • Filtering facepiece (N95) or half-mask air-purifying respirator 10
  • Full-facepiece air-purifying respirator 50
  • PAPR with loose-fitting facepiece, hood, or helmet 25
  • PAPR with half mask 50
  • PAPR with full facepiece or with hood/helmet demonstrated to perform at that level 1,000
  • Supplied-air (airline), continuous flow, loose-fitting hood/helmet 25
  • Supplied-air, continuous flow, full facepiece 1,000
  • SCBA, pressure demand, full facepiece 10,000

Using the APF Maximum Use Concentration (MUC) = APF × PEL \text{Maximum Use Concentration (MUC)} = \text{APF} \times \text{PEL} Maximum Use Concentration (MUC) = APF × PEL

For respirable crystalline silica (PEL 50 µg/m³ ), a half-mask APF 10 respirator is valid up to 500 µg/m³ . Above that, the crew needs an APF 25 PAPR or better — which is exactly why several Table 1 entries in 1926.1153 specify "APF 25" for longer-duration tasks (see Section 9.2).

Caution

APF 10 is the whole reason QLFT exists. Qualitative fit testing is only permitted for respirators used at APF 10 or below. If the exposure assessment demands an APF 50 full facepiece, the employer must run a quantitative fit test.

  • 4. Cartridge and Filter Selection
  • Particulate filters — the NIOSH letter/number system
  • Letter Oil Resistance Number Filter Efficiency
  • N N ot resistant to oil 95 95%
  • R R esistant to oil (single shift) 99 99%
  • P Oil P roof 100 99.97%

An N95 filters 95% of non-oil particulates. A P100 — the magenta cartridge — filters 99.97% and is oil proof; it is the standard selection for lead and asbestos work.

Chemical cartridges

Color-coded by contaminant family (organic vapor = black; acid gas = white; ammonia = green; the combination OV/AG/P100 = yellow with magenta). Cartridges must be changed on a documented change schedule based on objective data or a manufacturer software model. Relying on the worker's sense of smell as a breakthrough indicator is not compliant — many contaminants have poor warning properties, and olfactory fatigue is real (recall hydrogen sulfide from Section 5.5).

The absolute limits

No air-purifying respirator of any kind may be used in:

Oxygen-deficient atmospheres (below 19.5%) — a filter cannot make oxygen

IDLH atmospheres — these require a pressure-demand SCBA or a combination airline with auxiliary SCBA escape cylinder, plus the two-in / two-out rule of 1910.134(g)(3)

  • Unknown atmospheres — an unknown atmosphere is treated as IDLH
  • 5. Voluntary Use — 1910.134(c)(2) and Appendix D

When exposures are below the level requiring a respirator but an employee wants to wear one anyway:

  • The employer must determine that voluntary use will not in itself create a hazard
  • The employer must provide the employee with the information in Appendix D of 1910.134

If the voluntary respirator is a filtering facepiece (dust mask) only , the employer is exempt from the written program, medical evaluation, and fit testing

If the voluntary respirator is a half mask, full facepiece, or any elastomeric respirator , the employer must provide medical evaluation and must ensure cleaning, storage, and maintenance — even though use is voluntary

Note

The single most common program failure is treating an elastomeric half mask as if it were a dust mask. Handing a worker a reusable half-mask respirator "if he wants one" triggers medical evaluation obligations that a paper N95 does not.