Study guide
1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)
OSHA 30-Hour Construction Safety Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety Management, Regulatory Framework & Worker Rights
1.1 OSHA Regulatory Structure, OSH Act, General Duty Clause & Worker Rights 1.2 Safety Management Systems (SMS) & Safety Culture Leadership 1.3 Leading vs. Lagging Indicators, Safety Metrics & Recordkeeping (OSHA 300/300A/301) 1.4 Multi-Employer Worksite Citation Policy & Subcontractor Safety Oversight 1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)
2 Chapter 2: Fall Protection Systems & Working at Heights
2.1 Fall Hazards, 6-Foot Rule & 29 CFR 1926 Subpart M Scope 2.2 Guardrail Systems, Safety Net Systems & Hole Covers 2.3 Personal Fall Arrest Systems (PFAS), Anchorages & Fall Clearance Calculations 2.4 Controlled Access Zones, Safety Monitoring Systems & Leading Edge Work 2.5 Stairways, Ladders & Access Systems (29 CFR 1926 Subpart X)
3 Chapter 3: Electrical Safety, Grounding & Energy Control
3.1 Electrical Hazards, Electrocution Dynamics & 29 CFR 1926 Subpart K 3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP) 3.3 Overhead Power Line Clearances & Encroachment Prevention 3.4 Lockout/Tagout (LOTO), De-energization & Hazardous Energy Control 3.5 Arc Flash Hazards, PPE Requirements & Qualified Worker Distinctions
4 Chapter 4: Scaffolding Systems & Aerial Lifts
4.1 Scaffold Classifications, Load Capacities & Subpart L General Requirements 4.2 Supported Scaffolds: Foundations, Planking, Bracing, Tie-ins & Erection 4.3 Suspended Scaffolds, Two-Point Swings & Rigging Counterweights 4.4 Aerial Lifts, Scissor Lifts & Mobile Elevated Work Platforms (MEWPs) 4.5 Competent Person Scaffold Inspection, Fall Protection & Access Rules
5 Chapter 5: Excavation, Trenching & Shoring Safety
5.1 Excavation Hazards, Soil Mechanics & Subpart P Scope 5.2 OSHA Soil Classification: Visual and Manual Field Testing (Types A, B, C) 5.3 Protective Systems: Sloping and Benching Ratios 5.4 Protective Systems: Hydraulic Shoring, Trench Boxes & Shields 5.5 Excavation Access/Egress, Hazardous Atmospheres & Competent Person Daily Inspections
6 Chapter 6: Cranes, Derricks, Hoists & Rigging
6.1 Subpart CC Scope, Operator Certification & Qualification Requirements 6.2 Crane Setup, Ground Conditions, Outriggers & Power Line Safety 6.3 Load Charts, Capacity Calculations & Lift Planning 6.4 Critical Lift Planning, Tandem Lifts & Personnel Hoisting 6.5 Rigging Hardware, Sling Angles, Hitches & Signal Person Qualifications
7 Chapter 7: Confined Spaces in Construction
7.1 29 CFR 1926 Subpart AA Scope & Confined Space vs. Permit-Required Confined Space (PRCS) 7.2 Atmospheric Testing: Sequential Order (O2, Flammability, Toxicity) & Calibration 7.3 PRCS Entry Permit Program, Isolation & Ventilation 7.4 Duties of Authorized Entrants, Attendants & Entry Supervisors 7.5 Non-Entry vs. Entry Rescue, Emergency Services & Retrieval Systems
8 Chapter 8: Incident Investigation, Root Cause Analysis & Prevention
8.1 Purpose of Incident Investigation & Blame-Free Reporting Culture 8.2 Immediate Response, Scene Security, Evidence Gathering & Witness Interviewing 8.3 Root Cause Analysis Methodologies: 5 Whys, Fishbone (Ishikawa), and Fault Tree 8.4 Human Factors, Swiss Cheese Model & Latent Organizational Failures 8.5 Corrective Action Plans, Hierarchy of Controls Application & Near-Miss Trending
9 Chapter 9: Occupational Health Hazards & Environmental Protection
9.1 Hazard Communication Standard (HazCom 2012 / GHS) & 16-Section Safety Data Sheets (SDSs) 9.2 Respirable Crystalline Silica (29 CFR 1926.1153) & Table 1 Control Methods 9.3 Lead & Asbestos Hazards in Construction Demolition and Renovation (29 CFR 1926.62 / 1926.1101) 9.4 Occupational Noise Exposure, Action Levels, PELs & Hearing Conservation Programs (Subpart D) 9.5 Thermal Stress (Heat Illness & Cold Injury Prevention) & Biological/Chemical Hazards
10 Chapter 10: Ergonomics, Material Handling & Tool Safety
10.1 Ergonomic Risk Factors in Construction & Musculoskeletal Disorders (MSDs) 10.2 Manual Material Handling, Safe Lifting Principles & Ergonomic Engineering Solutions 10.3 Hand-Arm Vibration Syndrome (HAVS), Whole-Body Vibration & Power Tool Safety (Subpart I) 10.4 Material Storage, Rigging Safety, Housekeeping & Disposal (29 CFR 1926 Subpart H) 10.5 Motor Vehicles, Heavy Equipment, Highway Work Zone Safety & Struck-By Prevention (Subpart O/G)
11 Chapter 11: Personal Protective and Life-Saving Equipment (29 CFR 1926 Subpart E)
11.1 PPE Programs, Hazard Assessment, the Proper-Fit Rule & Employer Payment 11.2 Head, Eye, and Face Protection (1926.100 / 1926.102) 11.3 Hearing, Hand, Foot, and Body Protection (1926.101 / 1926.95 / 1926.96) 11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing (1926.103)
12 Chapter 12: Struck-By and Caught-In/Between Focus Four Hazards
12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects 12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection 12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts (1926.602)
13 Chapter 13: Concrete, Masonry & Steel Erection (Subparts Q and R)
13.1 Cast-in-Place Concrete, Formwork, Shoring & Rebar Impalement (Subpart Q) 13.2 Masonry Construction, Limited Access Zones & Precast/Tilt-Up Panels (Subpart Q) 13.3 Steel Erection: Column Anchorage, Connectors, Decking & the CDZ (Subpart R)
14 Chapter 14: Fire Prevention, Welding & Cutting, and Demolition (Subparts F, J, T)
14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F) 14.2 Welding, Cutting & Hot Work (29 CFR 1926 Subpart J) 14.3 Demolition: Engineering Surveys & Sequenced Removal (29 CFR 1926 Subpart T)
15 Chapter 15: Emergency Preparedness, Site Welfare & Safety Leadership
15.1 Emergency Action Plans, Medical Services, First Aid & Sanitation (1926.35 / .50 / .51) 15.2 Foundations for Safety Leadership & the OSHA Outreach Card
1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)
Key Takeaways Explain This Topic AI
A Job Hazard Analysis (JHA / JSA) is a proactive 4-step technique: 1) Break job into sequential steps, 2) Identify hazards at each step, 3) Engineer preventive controls, and 4) Review and update.
The Hierarchy of Controls ranks safety interventions from most effective to least effective: Elimination, Substitution, Engineering Controls, Administrative Controls, and Personal Protective Equipment (PPE).
Personal Protective Equipment (PPE) is the least effective control and last line of defense because it does not eliminate the hazard and relies entirely on human compliance.
A Site-Specific Safety Plan (SSSP) customizes safety protocols for a specific project's unique hazards, logistics, competent persons, and high-risk operations.
Under 29 CFR 1926.50, if emergency medical care is not accessible within 3-4 minutes for life-threatening emergencies, a trained and certified on-site First Aid/CPR responder is legally required.
Last updated: August 2026
1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)
Systematic hazard control in construction occurs at two fundamental levels: the macro-level project plan via the Site-Specific Safety Plan (SSSP) , and the micro-level task plan via the Job Hazard Analysis (JHA / JSA) . To ensure controls are robust and sustainable, safety professionals must apply the Hierarchy of Controls , prioritize engineering solutions over personal protective equipment, and structure comprehensive emergency action and medical response systems.
1. Job Hazard Analysis (JHA / JSA) Methodology
A Job Hazard Analysis (JHA) —also called a Job Safety Analysis (JSA)—is a systematic technique that focuses on job tasks as the medium to identify hazards before they occur. It examines the relationship between the worker, the task, the tools, and the work environment.
- The Four-Step JHA Process ┌─────────────────────────────────────────────────────────────┐
- │ STEP 1: BREAK JOB DOWN INTO STEPS │
- │ Divide task into chronological, manageable steps (5-10). │
- │ Avoid making steps too broad or overly microscopic. │
- └──────────────────────────────┬──────────────────────────────┘
- │
- ▼
- ┌─────────────────────────────────────────────────────────────┐
- │ STEP 2: IDENTIFY POTENTIAL HAZARDS │
- │ Identify physical, chemical, biological, and ergonomic │
- │ hazards associated with each individual step. │
- └──────────────────────────────┬──────────────────────────────┘
- │
- ▼
- ┌─────────────────────────────────────────────────────────────┐
- │ STEP 3: DETERMINE PREVENTIVE CONTROLS │
- │ Apply Hierarchy of Controls to engineer specific, │
- │ actionable safeguards for each identified hazard. │
- └──────────────────────────────┬──────────────────────────────┘
- │
- ▼
- ┌─────────────────────────────────────────────────────────────┐
- │ STEP 4: COMMUNICATE, REVIEW & UPDATE │
- │ Review with crew in daily tailgate talk; update when │
- │ tools, equipment, site conditions, or crew members change. │
- └─────────────────────────────────────────────────────────────┘
- Construction JHA Example: Installing Exterior Precast Concrete Wall Panels
Step # Sequential Job Step Potential Hazards Identified Preventive Control Measures (Hierarchy)
1 Rigging precast panel on flatbed delivery truck. • Struck-by swinging panel; • Crushed hands/pinch points; • Fall from flatbed trailer ( > 4 >4 > 4 ft) • Certified rigger inspects rigging hardware.; • Use tag lines; establish 10-ft exclusion zone.; • Flatbed trailer ladder platform with guardrails.
2 Hoisting and swinging panel to 4th floor perimeter. • Crane tip-over / overload; • Struck-by dropped load; • Overhead power line contact • Critical lift plan signed by PE; verify load charts.; • Barricade swing radius on ground.; • Maintain 20-ft clearance from 50kV power lines.
3 Guiding, plumbing, and temporary bolting at floor edge. • Fall from height ( > 6 >6 > 6 ft) at unprotected edge; • Crushed fingers between panel and slab • PFAS anchored to 5,000-lb rated inserts.; • Use alignment pry bars; no hands beneath panel.; • Install perimeter safety net below work deck.
4 Welding permanent structural connection inserts. • Fire / hot slag ignition; • Toxic welding fumes; • Arc flash eye injury • Hot work permit; 30-minute fire watch.; • Local exhaust ventilation (LEV) / HEPA extractor.; • Shade 10-12 welding hood and fire-resistant PPE.
2. The Hierarchy of Controls
The Hierarchy of Controls is a globally recognized framework developed by NIOSH and enforced by OSHA that ranks hazard control methods based on their inherent effectiveness, reliability, and sustainability: ┌─────────────────────────────────────────────────────────────┐
- │ 1. ELIMINATION │ ▲ MOST
- │ Physically remove the hazard completely │ │ EFFECTIVE
- ├─────────────────────────────────────────────────────────────┤ │
- │ 2. SUBSTITUTION │ │
- │ Replace the hazard with a safer one │ │
- ├─────────────────────────────────────────────────────────────┤ │
- │ 3. ENGINEERING CONTROLS │ │
- │ Isolate people from the hazard physically │ │
- ├─────────────────────────────────────────────────────────────┤ │
- │ 4. ADMINISTRATIVE CONTROLS │ │
- │ Change the way people work │ │
- ├─────────────────────────────────────────────────────────────┤ │
- │ 5. PPE │ │ LEAST
- │ Protect the worker with Personal Equipment │ ▼ EFFECTIVE
- └─────────────────────────────────────────────────────────────┘
- In-Depth Comparison of Control Tiers
Tier & Strategy Mechanism & Effectiveness Inherent Reliability Construction Field Applications
1. Elimination Completely removes the hazard from the workplace. Highest (100% hazard removal; no reliance on human behavior). • Prefabricating roof trusses, MEP racks, or ductwork at grade level to eliminate working at heights.; • Eliminating utility trench entry by utilizing horizontal directional drilling (HDD).
2. Substitution Replaces a hazardous material, equipment, or process with a significantly less hazardous alternative. High (Reduces inherent risk; minimal human error exposure). • Replacing high-VOC solvent paints with water-based low-VOC formulations.; • Replacing lead solder with tin-antimony solder.; • Replacing pneumatic jackhammers with hydraulic excavators equipped with breaker attachments.
3. Engineering Controls Places a physical barrier or mechanical system between the worker and the hazard. Medium-High (Protects automatically once installed; independent of worker behavior). • Standard perimeter guardrails and hole covers (Subpart M).; • Trench shields and hydraulic shoring boxes (Subpart P).; • Integrated water-delivery shrouds and vacuum dust collectors for concrete cutting (Silica Table 1).; • Acoustic enclosures around stationary diesel generators.
4. Administrative Controls Establishes work procedures, policies, training, scheduling, and warnings to reduce exposure duration. Low-Medium (Relies heavily on strict supervisory enforcement and worker compliance). • Rotating workers between high-noise or high-heat tasks to limit individual exposure time.; • Lockout/Tagout (LOTO) energy control procedures.; • Designating Controlled Access Zones (CAZ) with warning lines.; • Mandatory pre-shift equipment inspections and toolbox talks.
5. Personal Protective Equipment (PPE) Provides personal wearable barriers to shield the worker from residual hazards. Lowest (Fails if sized incorrectly, worn improperly, or damaged; leaves hazard fully active in environment). • Hard hats, safety glasses, high-visibility class 2/3 vests.; • Full-body fall arrest harnesses, shock-absorbing lanyards.; • N95 / half-face elastomeric air-purifying respirators.; • Hearing protection (earplugs/earmuffs) and cut-resistant gloves.
Caution
Exam Trap: PPE is always the last line of defense . OSHA standards require employers to implement all feasible engineering and administrative controls before relying on PPE. If an employer relies solely on respirators without evaluating water suppression or local exhaust ventilation for silica dust, OSHA will issue a serious citation.
3. Site-Specific Safety Plans (SSSP)
A generic corporate safety manual does not satisfy OSHA requirements on a complex construction project. A Site-Specific Safety Plan (SSSP) is a customized document tailored to the unique physical layout, environmental conditions, trade scopes, and regulatory risks of a specific project.
Mandatory Components of an SSSP
Project Directory & Emergency Contacts: Project leadership, safety director, local hospital routes, police/fire dispatch, and OSHA Area Office contacts.
Named Competent Persons: Designated, qualified competent persons for specific high-hazard operations (Excavations, Scaffolds, Cranes/Rigging, Fall Protection, Confined Spaces).
Site Logistics & Traffic Control Plan: Dedicated haul roads, material laydown yards, crane setup zones, pedestrian walkways, and delivery access gates.
Hazard Communication (HazCom) & SDS Library: Complete inventory of hazardous chemicals on site, designated SDS binder/electronic station location, and secondary container labeling rules.
Specialized High-Hazard Activity Plans:
Project Fall Protection Plan (including rescue procedures).
Excavation and Shoring Plan.
Confined Space Entry Program & Permit System.
Hot Work Permit & Fire Prevention Plan.
Crane Lift Plans & Rigging Protocols.
Subcontractor Management & Safety Enforcement: Pre-qualification rules, disciplinary policies, and daily JHA audit procedures.
4. Emergency Action Plans (EAP — 29 CFR 1926.35)
Under 29 CFR 1926.35 , construction employers must establish a written Emergency Action Plan (EAP) to ensure orderly evacuation and response during fires, structural collapses, toxic releases, or severe weather.
Key Statutory Requirements
Written vs. Oral: Employers with more than 10 employees must have a formal written EAP available at the jobsite. Employers with 10 or fewer employees may communicate the plan orally.
Mandatory EAP Elements:
Emergency escape procedures and designated primary and secondary evacuation route assignments.
Procedures for employees who remain on site to operate critical plant operations or shut off main utilities before evacuating.
Headcount and accounting procedures to ensure all employees are accounted for at designated muster / assembly points .
Rescue and medical duties for designated first responders.
The preferred means of reporting fires and emergencies (e.g., air horns, two-way radios, siren codes, 911 dispatch).
Designated contact persons responsible for plan explanations and updates.
5. Medical Services and First Aid (29 CFR 1926.50)
Under 29 CFR 1926.50 , employers must ensure prompt medical attention in case of serious injury:
Emergency Medical Access: If a medical clinic, hospital, or infirmary is not reasonably accessible in terms of time and distance (standard OSHA interpretation: 3 to 4 minutes for life-threatening emergencies involving suffocation, severe bleeding, or electrocution; 15 minutes for other serious injuries), a person with a valid certificate in First Aid and CPR must be available on site.
First Aid Supplies: First aid kits must be readily accessible in weatherproof containers with individually sealed packages, inspected weekly to replace expended items.
Emergency Eyewash / Showers: Where workers are exposed to corrosive materials (e.g., battery charging stations, acid washing, chemical grout), facilities for quick drenching or flushing of eyes and body must be provided within the immediate work area (meeting ANSI Z358.1: accessible within 10 seconds, providing 15 minutes of continuous flushing ).
Emergency Communication: Emergency telephone numbers (physicians, hospitals, ambulances, fire departments) must be conspicuously posted in the jobsite trailer and near primary telephones.