Study guide

12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection

OSHA 30-Hour Construction Safety Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety Management, Regulatory Framework & Worker Rights

1.1 OSHA Regulatory Structure, OSH Act, General Duty Clause & Worker Rights 1.2 Safety Management Systems (SMS) & Safety Culture Leadership 1.3 Leading vs. Lagging Indicators, Safety Metrics & Recordkeeping (OSHA 300/300A/301) 1.4 Multi-Employer Worksite Citation Policy & Subcontractor Safety Oversight 1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)

2 Chapter 2: Fall Protection Systems & Working at Heights

2.1 Fall Hazards, 6-Foot Rule & 29 CFR 1926 Subpart M Scope 2.2 Guardrail Systems, Safety Net Systems & Hole Covers 2.3 Personal Fall Arrest Systems (PFAS), Anchorages & Fall Clearance Calculations 2.4 Controlled Access Zones, Safety Monitoring Systems & Leading Edge Work 2.5 Stairways, Ladders & Access Systems (29 CFR 1926 Subpart X)

3 Chapter 3: Electrical Safety, Grounding & Energy Control

3.1 Electrical Hazards, Electrocution Dynamics & 29 CFR 1926 Subpart K 3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP) 3.3 Overhead Power Line Clearances & Encroachment Prevention 3.4 Lockout/Tagout (LOTO), De-energization & Hazardous Energy Control 3.5 Arc Flash Hazards, PPE Requirements & Qualified Worker Distinctions

4 Chapter 4: Scaffolding Systems & Aerial Lifts

4.1 Scaffold Classifications, Load Capacities & Subpart L General Requirements 4.2 Supported Scaffolds: Foundations, Planking, Bracing, Tie-ins & Erection 4.3 Suspended Scaffolds, Two-Point Swings & Rigging Counterweights 4.4 Aerial Lifts, Scissor Lifts & Mobile Elevated Work Platforms (MEWPs) 4.5 Competent Person Scaffold Inspection, Fall Protection & Access Rules

5 Chapter 5: Excavation, Trenching & Shoring Safety

5.1 Excavation Hazards, Soil Mechanics & Subpart P Scope 5.2 OSHA Soil Classification: Visual and Manual Field Testing (Types A, B, C) 5.3 Protective Systems: Sloping and Benching Ratios 5.4 Protective Systems: Hydraulic Shoring, Trench Boxes & Shields 5.5 Excavation Access/Egress, Hazardous Atmospheres & Competent Person Daily Inspections

6 Chapter 6: Cranes, Derricks, Hoists & Rigging

6.1 Subpart CC Scope, Operator Certification & Qualification Requirements 6.2 Crane Setup, Ground Conditions, Outriggers & Power Line Safety 6.3 Load Charts, Capacity Calculations & Lift Planning 6.4 Critical Lift Planning, Tandem Lifts & Personnel Hoisting 6.5 Rigging Hardware, Sling Angles, Hitches & Signal Person Qualifications

7 Chapter 7: Confined Spaces in Construction

7.1 29 CFR 1926 Subpart AA Scope & Confined Space vs. Permit-Required Confined Space (PRCS) 7.2 Atmospheric Testing: Sequential Order (O2, Flammability, Toxicity) & Calibration 7.3 PRCS Entry Permit Program, Isolation & Ventilation 7.4 Duties of Authorized Entrants, Attendants & Entry Supervisors 7.5 Non-Entry vs. Entry Rescue, Emergency Services & Retrieval Systems

8 Chapter 8: Incident Investigation, Root Cause Analysis & Prevention

8.1 Purpose of Incident Investigation & Blame-Free Reporting Culture 8.2 Immediate Response, Scene Security, Evidence Gathering & Witness Interviewing 8.3 Root Cause Analysis Methodologies: 5 Whys, Fishbone (Ishikawa), and Fault Tree 8.4 Human Factors, Swiss Cheese Model & Latent Organizational Failures 8.5 Corrective Action Plans, Hierarchy of Controls Application & Near-Miss Trending

9 Chapter 9: Occupational Health Hazards & Environmental Protection

9.1 Hazard Communication Standard (HazCom 2012 / GHS) & 16-Section Safety Data Sheets (SDSs) 9.2 Respirable Crystalline Silica (29 CFR 1926.1153) & Table 1 Control Methods 9.3 Lead & Asbestos Hazards in Construction Demolition and Renovation (29 CFR 1926.62 / 1926.1101) 9.4 Occupational Noise Exposure, Action Levels, PELs & Hearing Conservation Programs (Subpart D) 9.5 Thermal Stress (Heat Illness & Cold Injury Prevention) & Biological/Chemical Hazards

10 Chapter 10: Ergonomics, Material Handling & Tool Safety

10.1 Ergonomic Risk Factors in Construction & Musculoskeletal Disorders (MSDs) 10.2 Manual Material Handling, Safe Lifting Principles & Ergonomic Engineering Solutions 10.3 Hand-Arm Vibration Syndrome (HAVS), Whole-Body Vibration & Power Tool Safety (Subpart I) 10.4 Material Storage, Rigging Safety, Housekeeping & Disposal (29 CFR 1926 Subpart H) 10.5 Motor Vehicles, Heavy Equipment, Highway Work Zone Safety & Struck-By Prevention (Subpart O/G)

11 Chapter 11: Personal Protective and Life-Saving Equipment (29 CFR 1926 Subpart E)

11.1 PPE Programs, Hazard Assessment, the Proper-Fit Rule & Employer Payment 11.2 Head, Eye, and Face Protection (1926.100 / 1926.102) 11.3 Hearing, Hand, Foot, and Body Protection (1926.101 / 1926.95 / 1926.96) 11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing (1926.103)

12 Chapter 12: Struck-By and Caught-In/Between Focus Four Hazards

12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects 12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection 12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts (1926.602)

13 Chapter 13: Concrete, Masonry & Steel Erection (Subparts Q and R)

13.1 Cast-in-Place Concrete, Formwork, Shoring & Rebar Impalement (Subpart Q) 13.2 Masonry Construction, Limited Access Zones & Precast/Tilt-Up Panels (Subpart Q) 13.3 Steel Erection: Column Anchorage, Connectors, Decking & the CDZ (Subpart R)

14 Chapter 14: Fire Prevention, Welding & Cutting, and Demolition (Subparts F, J, T)

14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F) 14.2 Welding, Cutting & Hot Work (29 CFR 1926 Subpart J) 14.3 Demolition: Engineering Surveys & Sequenced Removal (29 CFR 1926 Subpart T)

15 Chapter 15: Emergency Preparedness, Site Welfare & Safety Leadership

15.1 Emergency Action Plans, Medical Services, First Aid & Sanitation (1926.35 / .50 / .51) 15.2 Foundations for Safety Leadership & the OSHA Outreach Card

12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection

Key Takeaways Explain This Topic AI

29 CFR 1926.300(b)(1) requires one or more methods of machine guarding to protect employees from point-of-operation hazards, ingoing nip points, rotating parts, and flying chips and sparks.

On bench and pedestal grinders, 29 CFR 1926.303(c)(2) requires the work rest to be kept within one-eighth inch of the wheel; the one-fourth-inch adjustable tongue guard limit comes from 29 CFR 1910.215(b)(9) and ANSI B7.1-1970, incorporated into construction by 1926.303(d).

Rollover protective structures are required by 29 CFR 1926.1000 on rubber-tired scrapers, front-end loaders and dozers, wheel-type tractors, crawler tractors and loaders, and motor graders manufactured after July 1, 1969.

Excavation cave-in is the deadliest caught-in/between hazard in construction — one cubic yard of soil weighs roughly 2,700 to 3,000 pounds.

A ROPS only protects an operator who stays inside the protected zone, which is why seat belts under 29 CFR 1926.602(a)(2) are inseparable from rollover protection.

Last updated: August 2026

12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection

Caught-in or between is the fourth Focus Four hazard, carrying a 30-minute minimum in the required 6-hour Focus Four block. It has three dominant construction expressions:

  • Buried or engulfed — trench cave-in, collapsing material, silo or hopper engulfment
  • Caught in machinery — pulled into rotating parts, nip points, or the point of operation
  • Crushed between objects — pinned between equipment and a fixed surface, or under a rolling machine

Cave-in was covered exhaustively in Chapter 5 ; recall the governing number — one cubic yard of soil weighs approximately 2,700 to 3,000 pounds , which is why unprotected trench collapse is nearly always fatal and why the protective-system trigger is 5 feet . This section covers the machinery half of the hazard.

  • 1. The General Machine Guarding Duty — 29 CFR 1926.300(b)
  • 1926.300(b)(1) — the point of operation and everything around it

"One or more methods of machine guarding shall be provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points, rotating parts, flying chips and sparks."

Four hazard families in one sentence, and each has a distinct guard:

Hazard What It Is Guard

Point of operation Where the machine does its work on the material — the blade, the bit, the die Barrier guard, presence-sensing device, blade guard, riving knife

Ingoing nip point Where two rotating parts meet, or a rotating part meets a tangent surface — belt onto pulley, chain onto sprocket, roller pair Enclosure. Nip points draw the hand in ; there is no reaction time

  • Rotating parts Shafts, spindles, couplings, flywheels, drums Full enclosure of any part exposed to contact
  • Flying chips and sparks Ejected material Guard plus eye and face PPE (Section 11.2)
  • 1926.300(b)(2) — moving parts

"When the periphery of the blades of a fan is less than seven (7) feet above the floor or working level, the blades shall be guarded with a guard having openings no larger than one-half (1/2) inch."

And the broader duty: belts, gears, shafts, pulleys, sprockets, spindles, drums, flywheels, chains, and other reciprocating, rotating, or moving parts must be guarded if exposed to contact by employees or if they otherwise create a hazard .

Note

Know which document holds which number. 1926.303 itself contains exactly one dimensional guard limit — the 1/8-inch work rest . The 1/4-inch adjustable tongue guard figure that every grinder inspection checklist prints comes from general industry 1910.215(b)(9) and from ANSI B7.1-1970 , which 1926.303(d) pulls into construction by reference. Both are enforceable on a construction site; only one is printed in Part 1926.

Caution

The most common construction machine-guarding violation is a removed guard on a portable tool — the lower blade guard wired back on a circular saw, the guard removed from a cut-off saw, a table saw run without a riving knife. "It was slowing us down" is the recorded cause in a large share of amputation cases.

2. Abrasive Wheels — 29 CFR 1926.303

Bench and pedestal grinders produce more construction amputations and eye injuries per machine-hour than almost any other tool, and the standard is written in fractions of an inch that are directly testable. ABRASIVE WHEEL GUARD CLEARANCES (1926.303)

  • ┌── Adjustable Tongue Guard
  • │ MAX 1/4 INCH from wheel
  • ▼
  • ╔═════════════╗
  • ║ ╭─────╮ ║
  • ║ ╱ WHEEL ╲ ║ ◄── Safety guard covers spindle end,
  • ║ │ • │ ║ nut, and flange projections
  • ║ ╲ ╱ ║
  • ║ ╰─────╯ ║
  • ╚══════╤══════╝
  • │
  • ─────────┴───── Work Rest
  • MAX 1/8 INCH from wheel

Requirement Value Citation

Work rest clearance to wheel Maximum 1/8 inch 1926.303(c)(2) — the one dimensional limit written into the construction standard itself

Guard coverage Must cover the spindle end, nut, and flange projections 1926.303(b)(2)

Maximum angular exposure of the wheel periphery and sides Not more than 90° , beginning not more than 65° above the horizontal plane of the spindle (up to 125° where work requires contact below the spindle plane) 1926.303(c)(1)

Adjustable tongue guard clearance to wheel Never exceed 1/4 inch 1910.215(b)(9) and ANSI B7.1-1970 , which 1926.303(d) incorporates by reference — not a numbered provision of 1926.303

Wheel speed Spindle speed must never exceed the maximum operating speed marked on the wheel ANSI B7.1-1970 via 1926.303(d)

Before mounting Ring test — suspend the wheel and tap; a clear ring indicates sound, a dull thud indicates a crack ANSI B7.1-1970 via 1926.303(d)

Why the clearances matter: a work rest more than 1/8 inch from the wheel lets the workpiece wedge into the gap, jamming the operator's hand against the wheel. A tongue guard more than 1/4 inch off allows a burst fragment to escape upward toward the face. Both are dimensional, both are checked with a rule, and both are cited constantly.

3. Rollover Protective Structures — 29 CFR 1926 Subpart W

1926.1000 requires rollover protective structures (ROPS) on the following machines manufactured after July 1, 1969 :

  • Rubber-tired self-propelled scrapers
  • Rubber-tired front-end loaders and rubber-tired dozers
  • Wheel-type agricultural and industrial tractors
  • Crawler tractors and crawler-type loaders
  • Motor graders

1926.1002 sets the protective-frame test and performance criteria for wheel-type agricultural and industrial tractors.

ROPS without a seat belt is decoration

A rollover protective structure works by creating a survivable volume around the operator's station during a roll. If the operator is thrown out of that volume, the ROPS becomes the object that crushes them. 29 CFR 1926.602(a)(2)(i) requires:

"Seat belts shall be provided on all equipment covered by this section and shall meet the requirements of the Society of Automotive Engineers, J386-1969, Seat Belts for Construction Equipment."

With two exceptions at 1926.602(a)(2)(ii) and (iii) : seat belts need not be provided for equipment designed only for standup operation , and need not be provided for equipment that does not have a rollover protective structure or adequate canopy protection .

Caution

Exam Trap: the second exception is frequently misread as "seat belts are optional." It means the opposite in practice — the moment a machine has a ROPS or canopy, the seat belt requirement attaches and it is not discretionary. A ROPS-equipped machine with a cut or removed seat belt is a citation.

Overhead protection

1926.1003 addresses overhead protection for operators of agricultural and industrial tractors. FOPS (falling object protective structures) protect against material dropped from above — required where the operator works under a load path, in demolition, or in trenching adjacent to overhead work.

4. Construction-Specific Caught-In/Between Traps

Situation Mechanism Control

Rotating superstructure swing radius Crushed between counterweight and a fixed object 29 CFR 1926.1424 work-area control — training plus control lines/barriers, or high-visibility markings where barriers are infeasible (Section 10.5)

Unblocked raised equipment Hydraulics bleed down; worker crushed under a bucket or blade 1926.600(a)(3) — suspended or elevated machinery must be substantially blocked before employees work beneath

Concrete pump and mixer skips Caught under a loading skip 1926.702(b) — mixers with a 1 cubic yard or larger loading skip require a mechanical clearing device and guardrails on each side

Powered concrete trowels Machine walks away and traps the operator against a wall 1926.702(i) — manually guided powered troweling machines must have a control switch that shuts off power when the operator releases it (deadman)

Unbraced masonry and tilt-up panels Wall overturns onto crew Limited access zone and bracing under 1926.706 (Section 13.2)

Loose clothing, rings, lanyards, long hair Drawn into a rotating shaft or nip point Remove or restrain before approaching rotating equipment

Note

Lockout/tagout is a caught-in/between control. Chapter 3.4 covered it as an electrical topic, but its most common construction application is preventing unexpected mechanical startup or stored-energy release while a worker is inside the machine envelope.