Study guide

12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts (1926.602)

OSHA 30-Hour Construction Safety Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Safety Management, Regulatory Framework & Worker Rights

1.1 OSHA Regulatory Structure, OSH Act, General Duty Clause & Worker Rights 1.2 Safety Management Systems (SMS) & Safety Culture Leadership 1.3 Leading vs. Lagging Indicators, Safety Metrics & Recordkeeping (OSHA 300/300A/301) 1.4 Multi-Employer Worksite Citation Policy & Subcontractor Safety Oversight 1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)

2 Chapter 2: Fall Protection Systems & Working at Heights

2.1 Fall Hazards, 6-Foot Rule & 29 CFR 1926 Subpart M Scope 2.2 Guardrail Systems, Safety Net Systems & Hole Covers 2.3 Personal Fall Arrest Systems (PFAS), Anchorages & Fall Clearance Calculations 2.4 Controlled Access Zones, Safety Monitoring Systems & Leading Edge Work 2.5 Stairways, Ladders & Access Systems (29 CFR 1926 Subpart X)

3 Chapter 3: Electrical Safety, Grounding & Energy Control

3.1 Electrical Hazards, Electrocution Dynamics & 29 CFR 1926 Subpart K 3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP) 3.3 Overhead Power Line Clearances & Encroachment Prevention 3.4 Lockout/Tagout (LOTO), De-energization & Hazardous Energy Control 3.5 Arc Flash Hazards, PPE Requirements & Qualified Worker Distinctions

4 Chapter 4: Scaffolding Systems & Aerial Lifts

4.1 Scaffold Classifications, Load Capacities & Subpart L General Requirements 4.2 Supported Scaffolds: Foundations, Planking, Bracing, Tie-ins & Erection 4.3 Suspended Scaffolds, Two-Point Swings & Rigging Counterweights 4.4 Aerial Lifts, Scissor Lifts & Mobile Elevated Work Platforms (MEWPs) 4.5 Competent Person Scaffold Inspection, Fall Protection & Access Rules

5 Chapter 5: Excavation, Trenching & Shoring Safety

5.1 Excavation Hazards, Soil Mechanics & Subpart P Scope 5.2 OSHA Soil Classification: Visual and Manual Field Testing (Types A, B, C) 5.3 Protective Systems: Sloping and Benching Ratios 5.4 Protective Systems: Hydraulic Shoring, Trench Boxes & Shields 5.5 Excavation Access/Egress, Hazardous Atmospheres & Competent Person Daily Inspections

6 Chapter 6: Cranes, Derricks, Hoists & Rigging

6.1 Subpart CC Scope, Operator Certification & Qualification Requirements 6.2 Crane Setup, Ground Conditions, Outriggers & Power Line Safety 6.3 Load Charts, Capacity Calculations & Lift Planning 6.4 Critical Lift Planning, Tandem Lifts & Personnel Hoisting 6.5 Rigging Hardware, Sling Angles, Hitches & Signal Person Qualifications

7 Chapter 7: Confined Spaces in Construction

7.1 29 CFR 1926 Subpart AA Scope & Confined Space vs. Permit-Required Confined Space (PRCS) 7.2 Atmospheric Testing: Sequential Order (O2, Flammability, Toxicity) & Calibration 7.3 PRCS Entry Permit Program, Isolation & Ventilation 7.4 Duties of Authorized Entrants, Attendants & Entry Supervisors 7.5 Non-Entry vs. Entry Rescue, Emergency Services & Retrieval Systems

8 Chapter 8: Incident Investigation, Root Cause Analysis & Prevention

8.1 Purpose of Incident Investigation & Blame-Free Reporting Culture 8.2 Immediate Response, Scene Security, Evidence Gathering & Witness Interviewing 8.3 Root Cause Analysis Methodologies: 5 Whys, Fishbone (Ishikawa), and Fault Tree 8.4 Human Factors, Swiss Cheese Model & Latent Organizational Failures 8.5 Corrective Action Plans, Hierarchy of Controls Application & Near-Miss Trending

9 Chapter 9: Occupational Health Hazards & Environmental Protection

9.1 Hazard Communication Standard (HazCom 2012 / GHS) & 16-Section Safety Data Sheets (SDSs) 9.2 Respirable Crystalline Silica (29 CFR 1926.1153) & Table 1 Control Methods 9.3 Lead & Asbestos Hazards in Construction Demolition and Renovation (29 CFR 1926.62 / 1926.1101) 9.4 Occupational Noise Exposure, Action Levels, PELs & Hearing Conservation Programs (Subpart D) 9.5 Thermal Stress (Heat Illness & Cold Injury Prevention) & Biological/Chemical Hazards

10 Chapter 10: Ergonomics, Material Handling & Tool Safety

10.1 Ergonomic Risk Factors in Construction & Musculoskeletal Disorders (MSDs) 10.2 Manual Material Handling, Safe Lifting Principles & Ergonomic Engineering Solutions 10.3 Hand-Arm Vibration Syndrome (HAVS), Whole-Body Vibration & Power Tool Safety (Subpart I) 10.4 Material Storage, Rigging Safety, Housekeeping & Disposal (29 CFR 1926 Subpart H) 10.5 Motor Vehicles, Heavy Equipment, Highway Work Zone Safety & Struck-By Prevention (Subpart O/G)

11 Chapter 11: Personal Protective and Life-Saving Equipment (29 CFR 1926 Subpart E)

11.1 PPE Programs, Hazard Assessment, the Proper-Fit Rule & Employer Payment 11.2 Head, Eye, and Face Protection (1926.100 / 1926.102) 11.3 Hearing, Hand, Foot, and Body Protection (1926.101 / 1926.95 / 1926.96) 11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing (1926.103)

12 Chapter 12: Struck-By and Caught-In/Between Focus Four Hazards

12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects 12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection 12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts (1926.602)

13 Chapter 13: Concrete, Masonry & Steel Erection (Subparts Q and R)

13.1 Cast-in-Place Concrete, Formwork, Shoring & Rebar Impalement (Subpart Q) 13.2 Masonry Construction, Limited Access Zones & Precast/Tilt-Up Panels (Subpart Q) 13.3 Steel Erection: Column Anchorage, Connectors, Decking & the CDZ (Subpart R)

14 Chapter 14: Fire Prevention, Welding & Cutting, and Demolition (Subparts F, J, T)

14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F) 14.2 Welding, Cutting & Hot Work (29 CFR 1926 Subpart J) 14.3 Demolition: Engineering Surveys & Sequenced Removal (29 CFR 1926 Subpart T)

15 Chapter 15: Emergency Preparedness, Site Welfare & Safety Leadership

15.1 Emergency Action Plans, Medical Services, First Aid & Sanitation (1926.35 / .50 / .51) 15.2 Foundations for Safety Leadership & the OSHA Outreach Card

12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts (1926.602)

Key Takeaways Explain This Topic AI

29 CFR 1926.602(d) makes the powered industrial truck operator training requirements for construction identical to those at 29 CFR 1910.178(l).

Operator performance must be evaluated at least once every three years, with refresher training triggered by an accident, a near miss, unsafe operation, a new truck type, or changed workplace conditions.

29 CFR 1926.602(c)(1)(vi) requires industrial trucks to meet the design, stability, inspection, testing, maintenance, and operation requirements of ANSI B56.1.

A forklift is stable only while the combined center of gravity of truck and load stays inside the stability triangle formed by the two front wheels and the center of the rear axle.

Rated capacity is stated at a specified load center — commonly 24 inches — and any load whose center of gravity sits farther forward derates the truck below its nameplate value.

Last updated: August 2026

12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts

Powered Industrial Vehicles is one of the fifteen Elective topics an authorized trainer may select for the 30-hour Construction course. On a real jobsite the telehandler is often the single busiest machine on site, and it produces a disproportionate share of tip-overs, struck-by events, and elevated-load incidents.

1. Which Rules Apply

Construction pulls from two directions:

Topic Where the Rule Lives

Design, construction, stability, inspection, testing, maintenance, operation 1926.602(c)(1)(vi) — must meet ANSI B56.1 , Safety Standards for Powered Industrial Trucks

  • Operator training 1926.602(d) — "identical to those set forth at § 1910.178(l)"
  • Seat belts 1926.602(a)(2)
  • Reverse signal alarm / observer 1926.602(a)(9)(ii)
  • Rough-terrain variable-reach trucks ANSI/ITSDF B56.6 is the applicable consensus standard

Note

This is the cleanest example in the whole course of construction borrowing from general industry. Just as 1926.103 imports 1910.134 for respirators, 1926.602(d) imports 1910.178(l) for forklift training. If an answer choice says "there is no forklift operator training requirement in construction," it is wrong.

  • 2. Operator Training and Evaluation — 1910.178(l)
  • Before operating

An employee may not operate a powered industrial truck independently until they have completed the training and been evaluated , except while training under the direct supervision of a qualified trainer, in a location where the training will not endanger anyone.

Training content

Truck-related topics: operating instructions and warnings for the specific type; differences from an automobile; controls and instrumentation; engine or motor operation; steering and maneuvering; visibility limitations; fork and attachment adaptation, operation, and limitations; vehicle capacity and stability ; inspection and maintenance the operator performs; refueling or battery charging; and any other operating limitation.

Workplace-related topics: surface conditions; composition and stability of loads; load manipulation, stacking, and unstacking; pedestrian traffic ; narrow aisles and restricted places; hazardous (classified) locations; operating on ramps and sloped surfaces ; potentially hazardous environmental conditions; and operating the truck in closed environments with poor ventilation (carbon monoxide accumulation).

Evaluation and refresher — the tested numbers

  • Requirement Trigger
  • Evaluation of operator performance At least once every 3 years

Refresher training Operator observed operating unsafely; involved in an accident or near-miss ; receives an evaluation revealing unsafe operation; assigned to a different type of truck ; or workplace conditions change in a manner affecting safe operation

Certification The employer must certify the training and evaluation, recording the operator's name, the training date, the evaluation date, and the identity of the person performing them

Caution

Exam Trap: three years is the evaluation interval, not a training expiration. Nothing in 1910.178(l) says a forklift card "expires in three years." What expires is the currency of the evaluation. And any of the five refresher triggers resets the clock immediately — a near miss on Tuesday requires refresher training regardless of when the last evaluation occurred.

3. The Data Plate and Load Center

Every powered industrial truck carries a data plate (nameplate) stating the model, serial number, weight, fuel type, attachments fitted, and — critically — the rated capacity at a stated load center .

Load center is the horizontal distance from the face of the forks to the center of gravity of the load . The industry standard reference is 24 inches . LOAD CENTER AND THE CAPACITY PENALTY

  • Fork face
  • │
  • │◄──── 24 in ────►│
  • ├─────────────────● Load CG at rated load center
  • │ → Truck rated 6,000 lb @ 24 in
  • │
  • │◄──────── 48 in ────────►│
  • ├─────────────────────────● Load CG doubled out
  • │ → Effective capacity roughly halved

The governing quantity is the load moment : weight multiplied by distance from the fulcrum (the front axle). Doubling the load center roughly halves the safe weight. A 6,000-pound-rated truck handling a bundle whose center of gravity sits 48 inches out is not a 6,000-pound machine anymore.

Caution

Attachments change the capacity, and the plate must reflect them. A jib, a rotator, a carpet pole, or a bucket adds dead weight forward of the axle and pushes the load center out. Under ANSI B56.1 the truck must be marked with the capacity for the attachment fitted. Running a machine with an attachment on the base-model data plate is operating without a valid rating.

4. The Stability Triangle

A sit-down counterbalanced forklift has three effective support points: the two front wheels and the center of the rear axle (the rear axle pivots on a center pin, so it acts as a single point). THE STABILITY TRIANGLE (plan view)

  • Front-left wheel ●───────────────● Front-right wheel
  • ╲ ╱
  • ╲ CG ╱
  • ╲ • ╱ Stable: combined center of
  • ╲ ╱ gravity inside the triangle
  • ╲ ╱
  • ╲ ╱
  • ╲ ╱
  • ● Rear axle center pivot

The truck remains stable while the combined center of gravity of the truck and its load stays inside this triangle. Four things move it toward an edge:

Raising the load — moves the combined CG up , shrinking the effective margin and making the triangle far less forgiving. A load that is stable at 12 inches can tip the machine at 20 feet.

Reaching out (load center beyond the rating, or a telehandler boom extended) — moves the CG forward toward the front axle line.

Turning — introduces lateral force that pushes the CG toward a side of the triangle. This is why sideways tip-over during a turn with an elevated load is the classic fatal forklift event.

Grade — driving across a slope, or with the load downhill, shifts the CG toward an edge. Travel with the load upgrade on ramps.

If it tips: stay in the seat

For a sit-down counterbalanced truck with an overhead guard, the survival protocol is:

Do not jump. The overwhelming majority of forklift tip-over fatalities are operators crushed by the overhead guard after jumping.

Stay seated, hold the wheel, brace your feet.

Lean away from the direction of the fall.

(Stand-up trucks with rear-entry are the opposite — the operator steps back and off. Know which machine the scenario describes.)

5. Telehandlers and Rough-Terrain Trucks

A telehandler is not a forklift with a longer reach — it is a variable-reach machine whose capacity changes continuously with boom angle and extension , exactly like a mobile crane (Chapter 6).

Feature Implication

Load chart, not a single capacity The operator must read capacity against boom angle and extension for the current configuration, just as with a crane load chart (Section 6.3)

Longitudinal Stability Indicator (LSI) Many machines display a forward-stability gauge; entering the red zone means retract or lower, not "push through"

Frame leveling and outriggers Level the frame before extending; where the machine has stabilizers, deploy them per the manual

Suspended loads Hanging a load from a fork or a hook converts the machine into a crane-like device with pendulum dynamics; many manufacturers publish a separate, much lower chart for suspended loads

Personnel platforms Only with a manufacturer-approved platform, on a machine designed for it, with the controls and interlocks the manufacturer specifies. Never a pallet, never a scrap-built cage

6. Pre-Operation Inspection

1910.178(q)(7) requires examination before each shift (or after each shift where used around the clock), and any truck found in unsafe condition must be removed from service immediately .

  • Engine Off Engine Running
  • Fluid levels and leaks under the machine Gauges and warning lights
  • Tires, wheels, lug nuts Steering play and response
  • Forks — cracks, bent heels, uneven tips, positive locking pins Service and parking brakes
  • Mast chains, hoses, and cylinders for wear and leaks Hoist, tilt, and auxiliary controls through full travel
  • Data plate present and legible Horn and reverse alarm
  • Overhead guard and load backrest secure Lights
  • Seat belt condition and function Any unusual noise or vibration

Note

Carbon monoxide is the underrated forklift hazard. Propane and diesel trucks operating inside a partially enclosed structure — a parking deck under construction, a shell building with the openings not yet cut — can drive CO well past the 50 ppm 8-hour PEL in under an hour. Mechanical ventilation and CO monitoring belong in the plan whenever an internal-combustion truck works indoors.