Study guide
12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects
OSHA 30-Hour Construction Safety Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Safety Management, Regulatory Framework & Worker Rights
1.1 OSHA Regulatory Structure, OSH Act, General Duty Clause & Worker Rights 1.2 Safety Management Systems (SMS) & Safety Culture Leadership 1.3 Leading vs. Lagging Indicators, Safety Metrics & Recordkeeping (OSHA 300/300A/301) 1.4 Multi-Employer Worksite Citation Policy & Subcontractor Safety Oversight 1.5 Job Hazard Analysis (JHA/JSA), Hierarchy of Controls & Site-Specific Safety Plans (SSSP)
2 Chapter 2: Fall Protection Systems & Working at Heights
2.1 Fall Hazards, 6-Foot Rule & 29 CFR 1926 Subpart M Scope 2.2 Guardrail Systems, Safety Net Systems & Hole Covers 2.3 Personal Fall Arrest Systems (PFAS), Anchorages & Fall Clearance Calculations 2.4 Controlled Access Zones, Safety Monitoring Systems & Leading Edge Work 2.5 Stairways, Ladders & Access Systems (29 CFR 1926 Subpart X)
3 Chapter 3: Electrical Safety, Grounding & Energy Control
3.1 Electrical Hazards, Electrocution Dynamics & 29 CFR 1926 Subpart K 3.2 Ground Fault Circuit Interrupters (GFCI) & Assured Equipment Grounding Conductor Program (AEGCP) 3.3 Overhead Power Line Clearances & Encroachment Prevention 3.4 Lockout/Tagout (LOTO), De-energization & Hazardous Energy Control 3.5 Arc Flash Hazards, PPE Requirements & Qualified Worker Distinctions
4 Chapter 4: Scaffolding Systems & Aerial Lifts
4.1 Scaffold Classifications, Load Capacities & Subpart L General Requirements 4.2 Supported Scaffolds: Foundations, Planking, Bracing, Tie-ins & Erection 4.3 Suspended Scaffolds, Two-Point Swings & Rigging Counterweights 4.4 Aerial Lifts, Scissor Lifts & Mobile Elevated Work Platforms (MEWPs) 4.5 Competent Person Scaffold Inspection, Fall Protection & Access Rules
5 Chapter 5: Excavation, Trenching & Shoring Safety
5.1 Excavation Hazards, Soil Mechanics & Subpart P Scope 5.2 OSHA Soil Classification: Visual and Manual Field Testing (Types A, B, C) 5.3 Protective Systems: Sloping and Benching Ratios 5.4 Protective Systems: Hydraulic Shoring, Trench Boxes & Shields 5.5 Excavation Access/Egress, Hazardous Atmospheres & Competent Person Daily Inspections
6 Chapter 6: Cranes, Derricks, Hoists & Rigging
6.1 Subpart CC Scope, Operator Certification & Qualification Requirements 6.2 Crane Setup, Ground Conditions, Outriggers & Power Line Safety 6.3 Load Charts, Capacity Calculations & Lift Planning 6.4 Critical Lift Planning, Tandem Lifts & Personnel Hoisting 6.5 Rigging Hardware, Sling Angles, Hitches & Signal Person Qualifications
7 Chapter 7: Confined Spaces in Construction
7.1 29 CFR 1926 Subpart AA Scope & Confined Space vs. Permit-Required Confined Space (PRCS) 7.2 Atmospheric Testing: Sequential Order (O2, Flammability, Toxicity) & Calibration 7.3 PRCS Entry Permit Program, Isolation & Ventilation 7.4 Duties of Authorized Entrants, Attendants & Entry Supervisors 7.5 Non-Entry vs. Entry Rescue, Emergency Services & Retrieval Systems
8 Chapter 8: Incident Investigation, Root Cause Analysis & Prevention
8.1 Purpose of Incident Investigation & Blame-Free Reporting Culture 8.2 Immediate Response, Scene Security, Evidence Gathering & Witness Interviewing 8.3 Root Cause Analysis Methodologies: 5 Whys, Fishbone (Ishikawa), and Fault Tree 8.4 Human Factors, Swiss Cheese Model & Latent Organizational Failures 8.5 Corrective Action Plans, Hierarchy of Controls Application & Near-Miss Trending
9 Chapter 9: Occupational Health Hazards & Environmental Protection
9.1 Hazard Communication Standard (HazCom 2012 / GHS) & 16-Section Safety Data Sheets (SDSs) 9.2 Respirable Crystalline Silica (29 CFR 1926.1153) & Table 1 Control Methods 9.3 Lead & Asbestos Hazards in Construction Demolition and Renovation (29 CFR 1926.62 / 1926.1101) 9.4 Occupational Noise Exposure, Action Levels, PELs & Hearing Conservation Programs (Subpart D) 9.5 Thermal Stress (Heat Illness & Cold Injury Prevention) & Biological/Chemical Hazards
10 Chapter 10: Ergonomics, Material Handling & Tool Safety
10.1 Ergonomic Risk Factors in Construction & Musculoskeletal Disorders (MSDs) 10.2 Manual Material Handling, Safe Lifting Principles & Ergonomic Engineering Solutions 10.3 Hand-Arm Vibration Syndrome (HAVS), Whole-Body Vibration & Power Tool Safety (Subpart I) 10.4 Material Storage, Rigging Safety, Housekeeping & Disposal (29 CFR 1926 Subpart H) 10.5 Motor Vehicles, Heavy Equipment, Highway Work Zone Safety & Struck-By Prevention (Subpart O/G)
11 Chapter 11: Personal Protective and Life-Saving Equipment (29 CFR 1926 Subpart E)
11.1 PPE Programs, Hazard Assessment, the Proper-Fit Rule & Employer Payment 11.2 Head, Eye, and Face Protection (1926.100 / 1926.102) 11.3 Hearing, Hand, Foot, and Body Protection (1926.101 / 1926.95 / 1926.96) 11.4 Respiratory Protection: Program, Selection, Medical Evaluation & Fit Testing (1926.103)
12 Chapter 12: Struck-By and Caught-In/Between Focus Four Hazards
12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects 12.2 Caught-In/Between Hazards, Machine Guarding & Rollover Protection 12.3 Powered Industrial Trucks, Telehandlers & Rough-Terrain Forklifts (1926.602)
13 Chapter 13: Concrete, Masonry & Steel Erection (Subparts Q and R)
13.1 Cast-in-Place Concrete, Formwork, Shoring & Rebar Impalement (Subpart Q) 13.2 Masonry Construction, Limited Access Zones & Precast/Tilt-Up Panels (Subpart Q) 13.3 Steel Erection: Column Anchorage, Connectors, Decking & the CDZ (Subpart R)
14 Chapter 14: Fire Prevention, Welding & Cutting, and Demolition (Subparts F, J, T)
14.1 Fire Protection and Prevention (29 CFR 1926 Subpart F) 14.2 Welding, Cutting & Hot Work (29 CFR 1926 Subpart J) 14.3 Demolition: Engineering Surveys & Sequenced Removal (29 CFR 1926 Subpart T)
15 Chapter 15: Emergency Preparedness, Site Welfare & Safety Leadership
15.1 Emergency Action Plans, Medical Services, First Aid & Sanitation (1926.35 / .50 / .51) 15.2 Foundations for Safety Leadership & the OSHA Outreach Card
12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects
Key Takeaways Explain This Topic AI
Struck-by is one of the four OSHA Focus Four hazards, which together carry a 6-hour minimum in the 30-hour Construction Outreach curriculum, with falls alone requiring at least 1 hour and 30 minutes.
Struck-by incidents are classified into four categories — flying, falling, swinging, and rolling objects — and the correct control differs for each.
Toeboards under 29 CFR 1926.502(j) must be at least 3.5 inches tall, allow no more than a 0.25-inch clearance above the walking surface, and withstand a 50-pound force.
The dividing line between struck-by and caught-in/between is the injury mechanism: harm from the impact itself is struck-by, while harm from crushing between two objects is caught-in/between.
Under 29 CFR 1926.759(a) in steel erection, all materials, equipment, and tools not in use while aloft must be secured against accidental displacement.
Last updated: November 2026
12.1 Struck-By Hazards: Flying, Falling, Swinging & Rolling Objects
The OSHA Focus Four is a Required topic carrying a 6-hour minimum in the 30-hour Construction Outreach course. Within that six hours, falls must be covered for at least 1 hour and 30 minutes , and the remaining three hazards — electrocution, struck-by, and caught-in or between — each carry a 30-minute minimum . Chapter 2 covered falls. Chapter 3 covered electrocution. This chapter closes the remaining two.
Struck-by is the hazard most often mislabeled, because "something hit me" describes an enormous range of events with entirely different controls.
1. The Four Struck-By Categories STRUCK-BY: FOUR MECHANISMS, FOUR CONTROL SETS
FLYING ───► Object propelled by a force (tool, wheel fragment, nail,
chip, pressurized debris). Control: guarding + eye/face PPE.
FALLING ──► Object under gravity from an elevation (tool, brick, load).
Control: toeboards, screens, canopies, nets, tool tethers,
exclusion zones below.
SWINGING ─► Suspended or mechanically driven object traversing a path
(crane load, backhoe bucket, unsecured wall panel).
Control: tag lines, exclusion zones, never under the load.
- ROLLING ──► Vehicle or equipment moving at grade (haul truck, skid steer,
- rolling pipe, loose material). Control: traffic plan, spotters,
backup alarms, high-visibility apparel, chocking.
Note
The classification decides the answer. A scenario in which a worker is hit by a bundle of conduit sliding off a flatbed is a rolling hazard controlled by chocking and blocking. The same conduit dropped from the third floor is a falling hazard controlled by toeboards and an exclusion zone. Read the mechanism before selecting the control.
- 2. Falling-Object Protection
- Toeboards — 29 CFR 1926.502(j)
When guardrails are used as falling-object protection, the toeboard requirements are precise and heavily tested:
- Requirement Value
- Minimum vertical height from top edge to walking/working level 3.5 inches
- Maximum clearance above the walking/working surface 0.25 inch
- Force the toeboard must withstand (any downward or outward point) 50 pounds
- Construction Solid, or with openings no greater than 1 inch in greatest dimension
When material is piled higher than the toeboard, paneling or screening must extend from the walking surface to the top rail (or higher) for the full opening length.
The full menu of falling-object protection
- System Where It Applies
- Toeboards Guardrailed edges, scaffold platforms (1926.451(h)(1))
- Screens / paneling Where material is stacked above the toeboard
- Debris nets / catch platforms Scaffolds and building perimeters where material could fall past the edge
Canopies / sidewalk sheds Over entrances and pedestrian routes. In demolition, 1926.850(k) requires canopies extending 8 feet from the building, capable of sustaining 150 pounds per square foot
- Barricaded exclusion zones The most reliable control: nobody below the work
- Tool tethers / lanyards Dropped-object prevention at height — increasingly standard on steel and MEP work
Hard hats Last line only. A hard hat is rated for a defined impact energy; a dropped wrench from ten floors exceeds it
Steel erection — 1926.759(a)
"All materials, equipment, and tools, which are not in use while aloft, shall be secured against accidental displacement."
This is the cleanest dropped-object rule in Part 1926 and it is absolute — bolts in an open bucket on a beam, a spud wrench balanced on a flange, or a level leaned against a column all violate it.
3. Flying-Object Hazards
Flying objects come from stored or applied energy, not gravity.
Source Failure Mode Control
Abrasive wheels Wheel bursts at speed; fragments leave at tangential velocity Ring test before mounting; never exceed the wheel RPM rating; guards in place (see Section 12.2)
Powder-actuated tools Fastener ricochet or spall through the base material Correct load level; never fire into soft/brittle base material or near an edge; see Section 10.3
Pneumatic nailers Blowback and ricochet, especially in sequential-to-contact trip conversions Sequential trip triggers; safety clips; 1926.302(b)(3) requires a safety clip or retainer on pneumatic tools over 100 psi
Compressed air cleaning Chips propelled at the operator and bystanders 1926.302(b)(4) — pressure reduced to less than 30 psi , with effective chip guarding and PPE
Masonry and concrete saws Blade fragments, spall Blade guards; correct blade for material; never remove the guard
4. Swinging-Object Hazards
Every crane pick, every excavator swing, and every wall panel being set creates a moving mass with momentum. The controls are behavioral and spatial:
Tag lines — control the load's rotation and pendulum from outside the swing path. Never wrap a tag line around a hand or body.
Never under the load. 29 CFR 1926.1425 restricts work under a suspended load to specific, narrow conditions (the load is fully supported by blocking or cribbing, or the employees are engaged in hooking/unhooking or initial connection, with the operator at the controls and the load stabilized).
Exclusion zones — barricade the radius, not just the pick point.
Load control on windy days. A tilt-up panel or a curtain-wall unit is a sail; wind speed limits come from the manufacturer and the lift plan (Sections 6.2 and 6.4).
Masonry walls under construction are swinging/falling hazards until braced — the limited access zone of 1926.706 exists precisely for this (Section 13.2).
5. Rolling-Object and Vehicle Hazards
Section 10.5 covers highway work zones, backing operations, and heavy-equipment traffic control in detail. Add three storage-and-material controls specific to struck-by:
Chock and block anything round. Pipe, conduit bundles, drums, and cable reels must be chocked or racked. 1926.250(b)(9) requires structural steel, pipe, bar stock, and conduit to be racked or blocked to prevent rolling or spreading.
Secure loads for transport. Material shifting off a flatbed or a buggy is a rolling struck-by.
Trench and excavation edges. Spoil piles and equipment must be set back at least 2 feet from the edge (1926.651(j)(2)); material rolling into an open trench strikes the crew below.
6. Struck-By or Caught-In/Between? The Deciding Test
OSHA draws the line at the injury mechanism , not the object:
If the injury is produced by the force of the impact alone, it is STRUCK-BY. If the injury is produced by crushing, pinching, or compression between two objects — or by being buried, engulfed, or squeezed — it is CAUGHT-IN/BETWEEN.
- Scenario Classification Reasoning
- Brick falls from the 4th floor and strikes a laborer's shoulder Struck-by Impact force alone
- Excavator counterweight pins a worker against a trench wall Caught-in/between Compression between two objects
- Trench wall collapses and buries a pipelayer Caught-in/between Engulfment
- Crane load swings and knocks a rigger off a platform Struck-by Impact; the fall is a secondary event
Skid steer backs into a laborer standing against a wall Caught-in/between Crushed between machine and fixed object
Skid steer backs into a laborer in open ground, knocking them down Struck-by Impact alone, no compression point
Caution
Exam Trap: the same machine produces both classifications depending on whether a fixed second surface is present. "Backed into in open ground" and "pinned against a wall" are different Focus Four categories.