Study guide

9.3 Hazardous Materials & Compressed Gases (29 CFR 1910.101-110)

OSHA 30-Hour General Industry Safety & Health Training Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Course Introduction & Overview

1.1 About the OSHA 30-Hour General Industry Card 1.2 Course Structure & Study Strategy

2 Chapter 2: Safety Management & OSHA Regulatory Framework

2.1 OSH Act, General Duty Clause & Worker Rights 2.2 OSHA Inspections, Citations & Penalties 2.3 Injury & Illness Recordkeeping (29 CFR 1904) 2.4 Managing Safety & Health Programs

3 Chapter 3: Hazard Communication & Chemical Hazards

3.1 Hazard Communication Standard (29 CFR 1910.1200) & GHS 3.2 Safety Data Sheets (SDS) & Container Labeling 3.3 Industrial Hygiene & Chemical Hazards

4 Chapter 4: Walking-Working Surfaces & Fire Protection

4.1 Walking-Working Surfaces & Housekeeping (29 CFR 1910.22) 4.2 Ladders, Stairways & Scaffolds (29 CFR 1910.23) 4.3 Fall Protection Systems & Criteria (29 CFR 1910.28-30) 4.4 Exit Routes, Emergency Action Plans & Fire Protection (29 CFR 1910.34-39)

5 Chapter 5: Personal Protective Equipment & Respiratory Protection

5.1 PPE Hazard Assessment & Selection (29 CFR 1910.132) 5.2 Head, Eye, Face, Hand & Foot Protection (29 CFR 1910.133-138) 5.3 Respiratory Protection Programs & Fit Testing (29 CFR 1910.134)

6 Chapter 6: Electrical Safety & Lockout/Tagout (LOTO)

6.1 Electrical Hazard Recognition & Grounding (29 CFR 1910.301-308) 6.2 Safe Work Practices & GFCI Requirements 6.3 Lockout/Tagout (LOTO) Energy Control (29 CFR 1910.147)

7 Chapter 7: Confined Spaces, Machine Guarding & Hot Work

7.1 Permit-Required Confined Spaces (29 CFR 1910.146) 7.2 Confined Space Atmosphere Testing & Entry Roles 7.3 Machine Guarding Principles & Guard Types (29 CFR 1910.211-219) 7.4 Welding, Cutting & Brazing — Hot Work Safety (29 CFR 1910.251-255)

8 Chapter 8: Materials Handling, Forklifts & Ergonomics

8.1 Materials Handling, Storage & Sling Safety (29 CFR 1910.176-184) 8.2 Powered Industrial Trucks (Forklifts) (29 CFR 1910.178) 8.3 Ergonomics & MSD Risk Factors

9 Chapter 9: Specialized Health Hazards & Process Safety

9.1 Bloodborne Pathogens Exposure Control (29 CFR 1910.1030) 9.2 Process Safety Management (PSM) (29 CFR 1910.119) 9.3 Hazardous Materials & Compressed Gases (29 CFR 1910.101-110)

9.3 Hazardous Materials & Compressed Gases (29 CFR 1910.101-110)

Key Takeaways Explain This Topic AI

Flammable liquids are classified into four GHS categories based on flashpoints and boiling points, with Category 1 being the most volatile (flashpoint below 73°F and boiling point at or below 95°F).

Storage of flammable liquids inside a single storage cabinet is limited to 60 gallons for Category 1, 2, or 3, and 120 gallons for Category 4.

In storage, oxygen cylinders must be separated from fuel-gas cylinders (such as acetylene) or combustible materials by at least 20 feet or a 5-foot-high fire-resistant barrier with a 1/2-hour rating.

Compressed gas cylinders must be stored upright, secured against tipping, and have their valve protection caps hand-tightened and in place except when in use.

Acetylene is highly unstable in its gas phase at pressures above 15 psig, requiring dissolved storage in liquid acetone within a porous cylinder material.

Last updated: July 2026

  • Hazardous Materials & Compressed Gases (29 CFR 1910.101-110)
  • Flammable Liquids: Classification & Storage (29 CFR 1910.106)

Flammable liquids present significant fire and explosion hazards in industrial environments. OSHA aligns its standard (29 CFR 1910.106) with the Globally Harmonized System (GHS), classifying liquids into four categories based on flashpoints and boiling points. The flashpoint is the lowest temperature at which a liquid emits sufficient vapor to form an ignitable mixture with air.

Category 1: Flashpoint < 73°F (23°C) and boiling point <= 95°F (35°C) (e.g., diethyl ether).

Category 2: Flashpoint < 73°F (23°C) and boiling point > 95°F (35°C) (e.g., gasoline, acetone).

Category 3: Flashpoint >= 73°F (23°C) and <= 140°F (60°C) (e.g., kerosene).

Category 4: Flashpoint > 140°F (60°C) and <= 199.4°F (93°C) (e.g., diesel fuel).

To minimize ignition risks, OSHA regulates storage capacities:

Container Types: Glass containers are limited to 1 pint for Category 1, 1 quart for Category 2, and 1 gallon for Category 3 or 4. Metal or approved plastic containers are capped at 1 gallon for Category 1, and 5 gallons for Categories 2, 3, and 4. Safety cans (with spring-closing lids and flame-arresting screens) can hold up to 2 gallons for Category 1, and 5 gallons for Categories 2, 3, and 4.

Storage Cabinets: Inside storage of flammable liquids is restricted to reduce fire load. A single cabinet can store a maximum of 60 gallons of Category 1, 2, or 3 liquids, or 120 gallons of Category 4 liquids. No more than three (3) cabinets are permitted in a single fire area, unless separated by at least 100 feet. Cabinets must be clearly labeled "FLAMMABLE - KEEP FIRE AWAY."

Ignition Controls & Industrial Ventilation

Static electricity builds up during liquid transfer and can cause sparks. When transferring Category 1 or 2 liquids, or Category 3 liquids with a flashpoint below 100°F (37.8°C), containers must be electrically bonded and grounded. A bond wire connects the containers to equalize electrical potential, while a ground wire drains the charge to the earth.

To prevent vapor accumulation, areas where flammable liquids are transferred must have ventilation providing at least 6 air changes per hour or 1 cubic foot per minute per square foot of floor area (cfm/sq ft). At least one portable fire extinguisher rated 10-B must be located within 10 feet of any storage room door, or within 30 feet of other indoor storage areas.

Compressed Gas Cylinders: General Safety (29 CFR 1910.101)

Compressed gases combine physical hazards (high pressure and heavy cylinders) with chemical hazards (toxicity, flammability, corrosiveness, or oxidation). A compromised cylinder valve can turn a cylinder into an unguided rocket.

Storage Regulations

Positioning & Security: Cylinders must be stored upright (unless designed for horizontal use) and secured with chains, straps, or racks to prevent tipping.

Valve Protection: Protective caps must be hand-tightened and in place at all times except when the cylinder is in use or connected.

Environment: Storage areas must be dry, ventilated, and located away from heat, open flames, or temperatures exceeding 125°F (51.7°C).

Separation of Incompatibles: In storage, oxygen cylinders must be separated from fuel-gas cylinders (like acetylene) or combustible materials (such as oil or grease) by a minimum of 20 feet (6.1 meters) or by a noncombustible barrier at least 5 feet (1.5 meters) high with a fire-resistance rating of at least one-half (1/2) hour .

Handling & Transportation

Moving Cylinders: Never drag, roll, or slide cylinders horizontally. Use a cylinder hand truck or cart.

Lifting: Cylinders must never be lifted by their valves or protection caps. Regulators must be removed and caps installed before transport.

DOT Standards: Cylinders must be constructed and maintained per Department of Transportation (DOT) standards. Visual inspections for rust, dents, or leaks must be conducted daily. Hydrostatic testing of cylinders must be performed every 5 or 10 years (indicated by a stamp on the collar) to verify structural integrity.

Acetylene Safety & Cylinder Stability

Acetylene is highly unstable and can decompose explosively at pressures exceeding 15 psig (pounds per square inch gauge). To safely store acetylene, cylinders contain a porous filler material saturated with liquid acetone, which dissolves the acetylene. Acetylene cylinders must always be stored and used in an upright position. If used horizontally, the liquid acetone can flow out with the gas, destabilizing the cylinder and creating a fire hazard.

Manifolding, Piping & Venting

Manifolds must be designed for specific gases and operating pressures. Piping must be tested and labeled. Backflow preventers (check valves) and flashback arrestors must be installed in fuel gas-oxygen systems.

Leak testing must be performed using soap-and-water solutions or approved leak detectors—never open flames. Leaking cylinders that cannot be tightened must be moved outdoors away from ignition sources, marked as defective, and returned to the supplier. Never vent cylinders indoors or in confined spaces.

  • Flammable / Gas Cylinder Requirement OSHA Limit / Separation Standard
  • Single Cabinet Flammable Capacity (Cat 1, 2, 3) Maximum 60 Gallons
  • Single Cabinet Flammable Capacity (Cat 4) Maximum 120 Gallons
  • Maximum Cabinets per Fire Area 3 Cabinets (unless separated by 100 ft)
  • Oxygen / Fuel-Gas Cylinder Separation Min. 20 feet OR 5-ft-high, 30-min fire barrier
  • Max Acetylene Operating Pressure 15 psig (for gas phase)
  • Max Storage Temp for Cylinders 125°F (51.7°C)