Study guide
4.2 Ladders, Stairways & Scaffolds (29 CFR 1910.23)
OSHA 30-Hour General Industry Safety & Health Training Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Course Introduction & Overview
1.1 About the OSHA 30-Hour General Industry Card 1.2 Course Structure & Study Strategy
2 Chapter 2: Safety Management & OSHA Regulatory Framework
2.1 OSH Act, General Duty Clause & Worker Rights 2.2 OSHA Inspections, Citations & Penalties 2.3 Injury & Illness Recordkeeping (29 CFR 1904) 2.4 Managing Safety & Health Programs
3 Chapter 3: Hazard Communication & Chemical Hazards
3.1 Hazard Communication Standard (29 CFR 1910.1200) & GHS 3.2 Safety Data Sheets (SDS) & Container Labeling 3.3 Industrial Hygiene & Chemical Hazards
4 Chapter 4: Walking-Working Surfaces & Fire Protection
4.1 Walking-Working Surfaces & Housekeeping (29 CFR 1910.22) 4.2 Ladders, Stairways & Scaffolds (29 CFR 1910.23) 4.3 Fall Protection Systems & Criteria (29 CFR 1910.28-30) 4.4 Exit Routes, Emergency Action Plans & Fire Protection (29 CFR 1910.34-39)
5 Chapter 5: Personal Protective Equipment & Respiratory Protection
5.1 PPE Hazard Assessment & Selection (29 CFR 1910.132) 5.2 Head, Eye, Face, Hand & Foot Protection (29 CFR 1910.133-138) 5.3 Respiratory Protection Programs & Fit Testing (29 CFR 1910.134)
6 Chapter 6: Electrical Safety & Lockout/Tagout (LOTO)
6.1 Electrical Hazard Recognition & Grounding (29 CFR 1910.301-308) 6.2 Safe Work Practices & GFCI Requirements 6.3 Lockout/Tagout (LOTO) Energy Control (29 CFR 1910.147)
7 Chapter 7: Confined Spaces, Machine Guarding & Hot Work
7.1 Permit-Required Confined Spaces (29 CFR 1910.146) 7.2 Confined Space Atmosphere Testing & Entry Roles 7.3 Machine Guarding Principles & Guard Types (29 CFR 1910.211-219) 7.4 Welding, Cutting & Brazing — Hot Work Safety (29 CFR 1910.251-255)
8 Chapter 8: Materials Handling, Forklifts & Ergonomics
8.1 Materials Handling, Storage & Sling Safety (29 CFR 1910.176-184) 8.2 Powered Industrial Trucks (Forklifts) (29 CFR 1910.178) 8.3 Ergonomics & MSD Risk Factors
9 Chapter 9: Specialized Health Hazards & Process Safety
9.1 Bloodborne Pathogens Exposure Control (29 CFR 1910.1030) 9.2 Process Safety Management (PSM) (29 CFR 1910.119) 9.3 Hazardous Materials & Compressed Gases (29 CFR 1910.101-110)
4.2 Ladders, Stairways & Scaffolds (29 CFR 1910.23)
Key Takeaways Explain This Topic AI
Fixed ladder rungs must support a concentrated load of at least 250 pounds applied at the midpoint.
For fixed ladders extending more than 24 feet, personal fall arrest systems or ladder safety systems are required, and cages are being phased out by November 18, 2036.
Portable ladders must follow the 4:1 slope rule, placing the base one-fourth of the ladder's working length away from the vertical wall support.
Portable ladders used to access an upper landing must extend at least 3 feet (36 inches) above the landing surface to provide a secure handhold.
Scaffolds must support their own weight and at least 4 times the maximum intended load, with guardrail protection triggered at 10 feet.
Last updated: July 2026
- 4.2 Ladders, Stairways & Scaffolds (29 CFR 1910.23)
- Introduction to Elevated Surfaces
Ladders, stairways, and scaffolds are essential tools for gaining access to elevated workspaces. However, working at heights is inherently dangerous. OSHA's Subpart D contains specific regulations to ensure that these devices are designed, manufactured, and used safely. By understanding the technical requirements for both fixed and portable climbing equipment, workers can mitigate the risks of falls, which remain a primary source of industrial accidents.
Fixed Ladder Standards (29 CFR 1910.23(d))
A fixed ladder is permanently attached to a structure, building, or equipment. Because fixed ladders are static, their design parameters are highly regulated:
Load Capacity: Fixed ladder rungs, cleats, and steps must be capable of supporting a concentrated load of at least 250 pounds (113 kg) applied at the midpoint of the rung.
Climbing Clearance: Fixed ladders must have a minimum perpendicular clearance of 7 inches (18 cm) between the rungs and the wall or any obstruction behind the ladder.
Fall Protection Triggers & Cages (29 CFR 1910.28(b)(9)):
Historically, OSHA required cages or wells for fixed ladders over 20 feet. Under the updated Subpart D rule, for fixed ladders that extend more than 24 feet (7.3 meters) above a lower level, the employer must equip the ladder with a personal fall arrest system (PFAS) or a ladder safety system.
For fixed ladders installed or replaced on or after November 19, 2018, cages are no longer considered acceptable fall protection. Instead, a PFAS or ladder safety system must be installed.
For existing fixed ladders with cages installed before November 19, 2018, employers may continue to use them, but by November 18, 2036, all existing fixed ladders over 24 feet must be retrofitted with a PFAS or ladder safety system.
Portable Ladder Safety and Setup (29 CFR 1910.23(c))
Portable ladders (including extension ladders and A-frame stepladders) are versatile but prone to improper setup and use. OSHA mandates several safety practices:
Pre-Use Inspections: Portable ladders must be inspected by a competent person before each work shift. Inspect for defects (e.g. cracked rails, grease). Defective ladders must be marked and removed from service.
The 4:1 Slope Rule: Non-self-supporting portable ladders (like extension ladders) must be set up at a safe angle. The horizontal distance from the base of the ladder to the vertical wall support must be one-fourth (1/4) of the working length of the ladder. This creates a 4:1 ratio (approx. 75.5-degree angle).
Calculation Example: If a ladder is positioned to touch a wall at a height of 16 feet, the base of the ladder must be placed exactly 4 feet away from the wall (16 divided by 4).
3 Feet Extension Rule: When using a portable ladder to gain access to an upper landing surface, the side rails must extend at least 3 feet (36 inches) above the upper landing surface. If a 3-foot extension is impossible, the ladder must be secured at the top with a grabbing device.
Three Points of Contact: Climbers must maintain three points of contact (two feet and one hand, or two hands and one foot) at all times when ascending or descending a ladder.
Stepladder Restrictions: Never use the top step or cap of a stepladder as a step. Additionally, do not stand on the step below the top cap.
- Ladder Feature Portable Extension Ladder Fixed Vertical Ladder
- Angle of Setup 4:1 slope (approx. 75.5 degrees) Vertical (90 degrees)
- Extension Above Landing Must extend 3 feet (36 inches) Side rails must extend 42 inches
- Fall Protection Trigger Typically not required if used properly Required if height exceeds 24 feet
- Rung Load Capacity Designed per duty rating (200-375 lbs) Must support at least 250 lbs
- Stairway Standards (29 CFR 1910.25)
Industrial stairways are subject to strict dimensional standards to prevent tripping hazards:
Angle of Rise: Standard stairs must be installed at an angle between 30 and 50 degrees from the horizontal.
Dimensions: Riser height must not exceed 9.5 inches (24 cm), and tread depth must be at least 9.5 inches. Riser heights and tread depths must be uniform throughout the stairway run (variation less than 1/4 inch).
Load Capacity: Stairways must support five times the maximum intended load, or a minimum concentrated load of 1,000 pounds.
Scaffold Safety Requirements (29 CFR 1910.27)
Scaffolds are temporary elevated platforms used to support workers and materials. General industry scaffold safety relies on structural integrity and fall prevention:
Load Safety Factor: Each scaffold and its components must be capable of supporting, without failure, its own weight and at least four times (4x) the maximum intended load applied or transmitted to it.
Fall Protection (Trigger at 10 Feet): Unlike general industry surfaces which require fall protection at 4 feet, fall protection on scaffolds is triggered at 10 feet (3.0 meters). Workers on scaffolds must be protected by a guardrail system or a personal fall arrest system (PFAS).
Guardrails and Toe Boards: Guardrails are required on open sides. Toe boards must be at least 3.5 inches high and withstand a 50-pound force to prevent falling objects.