Study guide

5.3 Sloping, Benching, Shoring & Shield Systems

OSHA 500 Trainer Course in Occupational Safety and Health Standards for the Construction Industry Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: OSHA Outreach Training Program Policies & Trainer Authorization

1.1 Outreach Trainer Qualifications, Authorization & Renewal 1.2 Class Administration, Attendance & Delivery Limits 1.3 10-Hour and 30-Hour Construction Curricula & Hour Requirements 1.4 Documentation, Records Retention & Card Processing 1.5 Required Outreach Curriculum, Focus Four Objectives & Student Materials 1.6 Trainer Roles, Training Language, Geographic Jurisdiction & Alternative Delivery

2 Chapter 2: OSH Act, Inspections & Multi-Employer Worksites

2.1 The OSH Act & The General Duty Clause 2.2 OSHA Inspection Process, Citations & Penalties 2.3 Injury/Illness Recordkeeping & Fatality Reporting 2.4 Multi-Employer Worksite Policy & Safety Roles 2.5 Managing Safety and Health: Programs, JHAs, Investigations & Safety Leadership

3 Chapter 3: Fall Protection Standards (29 CFR 1926 Subpart M)

3.1 Fall Protection Triggers, Scope & Duty to Have Fall Protection 3.2 Guardrail Systems, Safety Nets & Falling Object Protection 3.3 Personal Fall Arrest Systems (PFAS), Positioning & Restraint 3.4 Warning Lines, Safety Monitoring & Fall Protection Plans

4 Chapter 4: Scaffolds, Stairways, and Ladders (Subparts L & X)

4.1 Supported Scaffolds: Capacity, Planking & Erection 4.2 Suspended Scaffolds, Special Types & Fall Protection 4.3 Stairways and Stair Rails 4.4 Portable and Fixed Ladders: Setup, Inspection & Use

5 Chapter 5: Excavations, Trenching & Soil Mechanics (Subpart P)

5.1 Excavation Hazards, Access & Protective System Triggers 5.2 Soil Classification & Field Testing Procedures 5.3 Sloping, Benching, Shoring & Shield Systems 5.4 Trench Atmospheres, Utilities & Daily Competent Person Inspections

6 Chapter 6: Cranes, Rigging & Heavy Equipment Safety

6.1 Crane Standards (Subpart CC): Setup, Ground Conditions & Power Lines 6.2 Crane Operation, Signal Persons & Operator Qualifications 6.3 Rigging Equipment & Slings (Subpart H) 6.4 Motor Vehicles, Mechanized Equipment & Struck-By Prevention

7 Chapter 7: Electrical Safety, Confined Spaces & Physical Hazards

7.1 Ground-Fault Protection (GFCI) & Assured Grounding Programs 7.2 Electrical Wiring, Overcurrent Protection & Lockout/Tagout 7.3 Confined Spaces in Construction (Subpart AA) 7.4 Fire Protection, Welding & Hot Work Safety (Subparts F & J)

8 Chapter 8: Health Hazards, Silica, Noise & Personal Protective Equipment

8.1 Respirable Crystalline Silica (1926.1153) & Dust Controls 8.2 Occupational Noise, Lead & Chemical Hazards 8.3 Hazard Communication & Safety Data Sheets 8.4 Personal Protective Equipment & Respiratory Protection

9 Chapter 9: Adult Learning Principles & Instructional Delivery

9.1 Principles of Adult Learning (Andragogy) & Learner Engagement 9.2 Writing Performance-Based Learning Objectives & Bloom's Taxonomy 9.3 Instructional Methods, Questioning & Classroom Management 9.4 Training Evaluation & OSHA 500 Presentation Test Preparation

10 Chapter 10: Additional 29 CFR 1926 Subparts & Outreach Elective Topics

10.1 Steel Erection (Subpart R) 10.2 Concrete and Masonry Construction (Subpart Q) 10.3 Hand and Power Tools (Subpart I) 10.4 Materials Handling, Storage, Use & Disposal and Powered Industrial Vehicles 10.5 Signs, Signals, Barricades & Demolition (Subparts G and T) 10.6 Subparts C & D: Employer Duties, Sanitation, Illumination, Heat and Cold Stress & Ergonomics

5.3 Sloping, Benching, Shoring & Shield Systems

Key Takeaways Explain This Topic AI

Maximum allowable sloping angles under 29 CFR 1926 Subpart P Appendix B are: Type A = 3/4:1 (53°), Type B = 1:1 (45°), and Type C = 1.5:1 (34°).

A short-term simple slope of 1/2:1 (63°) is permitted in Type A soil only if the trench is 12 feet or less in depth and open for 24 hours or less.

Benching is permitted in Type A and Type B soils (max bench height of 4 feet in Type B), but is strictly PROHIBITED in Type C soil.

Trench boxes (shields) must extend at least 18 inches above the vertical side when the excavation is sloped above the top of the box.

An excavation may extend a maximum of 2 feet below the bottom of a trench shield only if the shield is rated for the full depth and there is no loss of soil behind or below the shield.

Last updated: September 2026

Sloping, Benching, Shoring & Shield Systems

Core Principle: When an excavation reaches 5 feet or deeper, employers must protect employees from cave-ins by selecting, designing, and installing an approved protective system under 29 CFR 1926.652. OSHA recognizes four fundamental protective methodologies: sloping, benching, shoring, and shielding. Each system functions on distinct mechanical principles, carries strict operational limitations, and requires specific geometric configurations based on soil classification.

1. Sloping Systems (Appendix B to Subpart P)

Sloping protects employees by cutting back the trench face at an angle inclined away from the excavation, eliminating the gravitational shear stress that causes soil failure.

Maximum Allowable Slopes for Excavations < 20 Feet Deep

OSHA 29 CFR 1926 Subpart P Appendix B (Table B-1) specifies the maximum allowable slope angle (expressed as the ratio of horizontal distance to vertical rise, H:V ) for each soil classification:

  • Soil Classification Maximum Allowable Slope (H:V) Angle from Horizontal Setback Ratio
  • Stable Rock Vertical (90°) 90° 0 ft horizontal per foot of depth
  • Type A Soil 3/4 : 1 53° 0.75 ft horizontal per 1.0 ft vertical rise
  • Type B Soil 1 : 1 45° 1.0 ft horizontal per 1.0 ft vertical rise

Type C Soil 1 1/2 : 1 (1.5 : 1) 34° 1.5 ft horizontal per 1.0 ft vertical rise MAXIMUM ALLOWABLE SLOPES (APPENDIX B)

  • Stable Rock Type A (3/4:1) Type B (1:1) Type C (1.5:1)
  • 90° 53° 45° 34°
  • │ ┌─ ┌── ┌───
  • │ │ 3/4 │ 1 │ 1.5
  • │ 1 │ │ │
  • │ │ 1 │ 1 │ 1
  • │ │ │ │
  • ─────┴───── ─────┴────── ─────┴────── ─────┴──────
  • The Short-Term Type A Exception

Under Appendix B, OSHA permits a steeper slope in Type A soil under very narrow operational conditions:

Slope Ratio: 1/2 : 1 (horizontal to vertical), which corresponds to an angle of 63 degrees from the horizontal.

Depth Limit: The excavation must be 12 feet (3.66 meters) or less in depth.

Time Limit: The excavation must remain open for 24 hours or less (short-term unsupported slope).

If the excavation will remain open for more than 24 hours, or if it exceeds 12 feet in depth, it must be sloped to the standard 3/4:1 (53°).

Calculating Real-World Surface Cut Widths

Safety professionals must calculate the total top width of a sloped trench to ensure adequate site clearance. Consider a 10-foot deep trench with a 4-foot wide bottom :

In Type A Soil (3/4:1):

Setback per side = 10 ft × 0.75 = 7.5 ft.

Total Top Width = 7.5 ft (left) + 4.0 ft (bottom) + 7.5 ft (right) = 19.0 feet .

In Type B Soil (1:1):

Setback per side = 10 ft × 1.0 = 10.0 ft.

Total Top Width = 10.0 ft (left) + 4.0 ft (bottom) + 10.0 ft (right) = 24.0 feet .

In Type C Soil (1.5:1):

Setback per side = 10 ft × 1.5 = 15.0 ft.

Total Top Width = 15.0 ft (left) + 4.0 ft (bottom) + 15.0 ft (right) = 34.0 feet .

2. Benching Systems (Appendix B)

Benching is a method of protecting employees from cave-ins by excavating the sides of an excavation to form one or a series of horizontal levels or steps, usually with vertical or near-vertical surfaces between levels.

Types of Benching Configurations

Simple Benching: A single vertical cut at the trench bottom followed by one horizontal step and a sloped upper bank.

Multiple Benching: A stair-stepped series of horizontal levels and vertical rises descending to the trench floor.

Permissible Soil Conditions and Critical Prohibitions

Type A Soil: Simple and multiple benching are permitted up to 20 feet in depth. The maximum vertical rise of the bottom bench is 4 feet , and intermediate benches may rise up to 5 feet , provided the overall slope does not exceed 3/4:1.

Type B Soil:

Benching is permitted only in cohesive Type B soils.

Maximum Bench Height: The vertical rise between benches cannot exceed 4 feet (1.22 meters) .

The overall slope of the benched system cannot exceed 1:1 (45 degrees) .

CRITICAL OSHA PROHIBITION: Benching in Type C Soil:

BENCHING IS STRICTLY PROHIBITED IN TYPE C SOIL.

Granular, cohesionless soils (sand, gravel, submerged material) possess no shear strength to support a vertical bench face. Any attempt to cut steps into Type C soil results in catastrophic sloughing and collapse.

3. Shoring Systems: Timber and Aluminum Hydraulic

Unlike sloping—which alters the geometry of the ground— shoring provides structural support against trench faces to prevent soil movement and cave-in initiation.

Structural Mechanics

Shoring works by exerting active lateral pressure against trench walls.

By maintaining lateral stress, shoring prevents soil decompaction, tension cracking, and shear plane failure before a collapse can start.

Timber Shoring (Appendix C)

Composed of wooden cross braces (struts) , horizontal wales (stringers) , and vertical uprights (sheeting) .

Components must be sized using the engineering tables in Appendix C based on soil type, trench depth, and trench width.

Today, timber shoring is largely supplanted by modern pre-engineered systems due to labor intensity and timber degradation.

Aluminum Hydraulic Shoring (Appendix D)

Pre-engineered systems consisting of vertical aluminum rails (shores) equipped with horizontal hydraulic cylinders (cross braces).

Major Safety Advantage: Hydraulic shores can be installed and removed completely from above ground , outside the trench. Workers never enter an unprotected trench to set or pull shores.

Operating Principles:

Pressurized using a portable hand pump filled with biodegradable fluid (water and water-soluble oil) to a typical gauge pressure of 750 to 1,500 psi .

Internal check valves lock hydraulic pressure in the cylinders.

Spacing of vertical rails (horizontal spacing) and cylinder spacing (vertical spacing) must strictly adhere to the manufacturer's tabulated data or OSHA Appendix D tables.

4. Shield Systems (Trench Boxes)

Shield systems , commonly called trench boxes , function on a fundamentally different principle than shoring:

Shoring vs. Shielding:

Shoring prevents the trench walls from moving or collapsing by applying active lateral support.

Shields (Trench Boxes) do NOT prevent trench walls from collapsing; they are engineered structural enclosures designed to withstand the immense dynamic impact forces of a cave-in, protecting the workers inside the protective envelope.

Critical Regulatory Requirements for Trench Boxes

Work Within the Shield Envelope:

Employees must remain inside the shielded perimeter at all times while in the trench.

Workers are strictly prohibited from working outside the shield , in front of or behind the box, or between the exterior shield wall and the unexcavated earth face.

Safe Egress Within the Box:

In accordance with 1926.651(c)(2), a ladder or safe egress must be located inside the shield so workers do not exit into an unprotected area.

Sloping Above the Trench Box (The 18-Inch Rule):

When an excavation is sloped above the top of a trench box, the shield must extend at least 18 inches (0.45 meters) above the vertical face / toe of the slope.

Rationale: This 18-inch lip acts as a retaining wall to catch rolling stones, boulders, sloughing earth, and spoil clods that tumble down the sloped bank, preventing them from falling into the box onto workers.

Unexcavated Earth Below the Shield (The 2-Foot Rule):

OSHA permits an excavation to extend a maximum of 2 feet (0.61 meters) below the bottom of a trench box, provided two conditions are met :

The shield is designed and rated to resist the lateral earth forces calculated for the full depth of the trench.

There is no indication of soil loss from behind or below the bottom of the shield (no sloughing, squeezing, boiling, or running soil).

Backfilling Void Spaces:

The space between the exterior of the trench shield and the trench wall must be backfilled or minimized .

If a large gap exists, collapsing soil gains kinetic momentum before striking the shield, generating dynamic impact forces that can shift, tip, or deform the box.

Loading diagram... Trench Box Combination Sloping and Depth Configuration Rules