Study guide

5.3 Specific Scaffold Types & Competent Person Roles

OSHA 510 Occupational Safety and Health Standards for Construction Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: OSH Act, Policies & Procedures

1.1 The OSH Act of 1970 & General Duty Clause 1.2 OSHA Inspections & Enforcement Priorities 1.3 Violations, Citations, & Penalty Framework 1.4 Multi-Employer Worksite Citation Policy

2 Chapter 2: Focus Four — Falls (Subpart M)

2.1 Fall Protection Scope & Triggers 2.2 Guardrail Systems & Safety Net Systems 2.3 Personal Fall Arrest Systems (PFAS) 2.4 Warning Line Systems & Controlled Access Zones 2.5 Fall Protection Training & Written Fall Protection Plans

3 Chapter 3: Focus Four — Electrical (Subpart K)

3.1 Ground-Fault Circuit Interrupters & Assured Equipment Grounding 3.2 Clearance Distances & Temporary Wiring Rules 3.3 Lockout/Tagout (LOTO) in Construction

4 Chapter 4: Focus Four — Struck-By & Caught-In

4.1 Heavy Equipment & Motor Vehicle Safety 4.2 Rigging Equipment & Hand/Power Tools 4.3 Concrete, Masonry & Steel Erection

5 Chapter 5: Scaffolds (Subpart L)

5.1 General Scaffold Requirements & Capacity 5.2 Scaffold Access, Fall Protection, & Falling Objects 5.3 Specific Scaffold Types & Competent Person Roles

6 Chapter 6: Excavations (Subpart P)

6.1 Protective Systems: Sloping, Shoring, & Shielding 6.2 Safe Egress, Access, & Hazardous Atmospheres 6.3 Soils Classification & Competent Person Inspections

7 Chapter 7: Health Hazards in Construction (Subpart D)

7.1 Respirable Crystalline Silica (1926.1153) 7.2 Lead (1926.62) & Asbestos (1926.1101) 7.3 Occupational Noise Exposure (1926.52) 7.4 Hazard Communication & Heat Illness Prevention

8 Chapter 8: PPE, Fire Protection, & Welding (Subparts E, F, J)

8.1 PPE & Employer Payment Rule 8.2 Fire Prevention & Protection in Construction 8.3 Welding, Cutting, & Hot Work Safety

9 Chapter 9: Cranes & Derricks (Subpart CC)

9.1 Crane Operator Certification & Inspections 9.2 Crane Operations: Power Line Clearances & Signal Persons

10 Chapter 10: Recordkeeping & Inspections (29 CFR 1904)

10.1 Recordkeeping Forms: OSHA 300, 301, & 300A 10.2 Reporting Fatalities, Hospitalizations, & Amputations 10.3 Recordkeeping Audits & Electronic Submission Rules

5.3 Specific Scaffold Types & Competent Person Roles

Key Takeaways Explain This Topic AI

Supported scaffolds with a height-to-base ratio greater than 4:1 must be secured using guys, ties, or braces.

Vertical ties must be installed every 20 feet or less for scaffolds less than or equal to 3 feet wide, and every 26 feet or less for scaffolds wider than 3 feet.

Suspension scaffolds require independent vertical lifelines for each worker, attached to independent anchorages capable of holding 5,000 lbs.

A Competent Person is responsible for supervising scaffold erection, dismantling, daily inspections, and training.

A Qualified Person is responsible for designing scaffolds, including custom systems and any scaffold exceeding 125 feet in height.

Last updated: July 2026

  • 5.3 Specific Scaffold Types & Competent Person Roles
  • Supported Scaffolds & The 4:1 Height-to-Base Rule (29 CFR 1926.451(c))

Supported scaffolds are platforms supported by legs, outrigger beams, brackets, poles, or uprights. Frame scaffolds are the most common type.

The 4:1 Height-to-Base Tipping Ratio

Supported scaffolds with a height-to-base width ratio of more than 4:1 must be restrained from tipping by guying, tying, bracing, or equivalent means. Base width is measured as the minimum width of the scaffold base (typically the width of the frame).

Worked Example :

A standard welded frame scaffold is 5 feet wide.

Height Threshold : 5 feet * 4 = 20 feet. Once the scaffold platform height reaches 20 feet, it must be secured to the structure.

If the scaffold is 3 feet wide, it must be secured before exceeding 12 feet.

Guying, Tying, and Bracing Intervals

First Tie/Guy : Must be installed at the closest frame header or brace member at or below the 4:1 height threshold.

Subsequent Vertical Spacing :

For scaffolds 3 feet wide or less: Vertical ties must be installed at intervals not to exceed 20 feet .

For scaffolds wider than 3 feet: Vertical ties must be installed at intervals not to exceed 26 feet .

Horizontal Spacing : Ties must be installed at each end of the scaffold and at horizontal intervals not to exceed 30 feet (measured from one end).

Suspension Scaffolds & Critical Safety Rules (29 CFR 1926.451(d))

Suspension scaffolds are platforms suspended by ropes or cables from overhead supports. Swing stages are a common example used in high-rise window washing or masonry repair.

Counterweights and Outriggers

Outrigger beams must be made of structural metal or equivalent strength material.

Counterweights : Must be made of non-flowable material (e.g., solid steel or concrete blocks). Sand, gravel, water, or other loose materials are strictly prohibited because they can leak, wash away, or be easily moved.

Counterweights must be secured to the outrigger beams to prevent accidental displacement.

Direct connections (such as tiebacks) must be used to secure outrigger beams to the roof or structure. Tiebacks must be perpendicular to the face of the building and equal in strength to the suspension ropes.

Independent Fall Arrest Systems (Lifelines)

When working on single-point or two-point adjustable suspension scaffolds, each employee must be attached to an independent vertical lifeline.

The lifeline must be secured to an independent anchorage point. It must NEVER be attached to the scaffold itself, the scaffold's suspension ropes, or the outrigger beams supporting the scaffold.

Rationale : If the scaffold structure or its primary suspension system fails, a worker attached to the scaffold would fall with it. The independent lifeline ensures that if the scaffold falls, the worker remains suspended safely.

Anchorage Strength : The independent anchorage must be capable of supporting at least 5,000 lbs per employee attached.

Mobile (Rolling) Scaffolds

Mobile scaffolds are supported scaffolds mounted on wheels or casters. They are widely used for overhead electrical, mechanical, and painting work.

Essential Mobile Scaffold Rules

Wheel/Caster Locks : Caster wheels must be locked with positive wheel and/or swivel locks to prevent movement while employees are working on the scaffold.

Prohibition of Riding : Employees must not ride mobile scaffolds unless all of the following conditions are met:

The floor or surface is within 3 degrees of level and free of pits, holes, or obstructions.

The height-to-base width ratio of the scaffold is 2:1 or less (unless outriggers are used).

The speed of movement is slow and controlled.

No employees are on any part of the scaffold extending beyond the wheels or casters.

Outrigger frames are installed on both sides of the scaffold if used to meet the height-to-base ratio.

Manual Force Application : Force used to move the scaffold must be applied as close to the base as possible, and not more than 5 feet above the surface.

Power Systems : Power systems must not be used to propel mobile scaffolds unless the scaffold is specifically designed for such propulsion.

Specialty Scaffolds: Pump Jack and Ladder Jack

Subpart L regulates many specialty scaffold systems commonly found on residential construction sites:

Pump Jack Scaffolds : These scaffolds utilize vertical poles and a pump mechanism to raise and lower the platform. The poles must be secured to the structure with rigid triangular bracing. The maximum platform height is 20 feet, and the workload is limited to light-duty (25 lbs/sq. ft.).

Ladder Jack Scaffolds : A light-duty scaffold supported by brackets attached to ladders. The maximum platform height is 20 feet. The span between ladders must not exceed 8 feet, and the ladders must be secured against slipping. Only light-duty work is permitted on ladder jack platforms, and no more than two employees may occupy them simultaneously.

The Roles of the Competent Person and Qualified Person

OSHA makes a clear distinction between the "Competent Person" and "Qualified Person" under Subpart L. Misunderstanding these roles is a very common exam trap.

The Qualified Person (Design & Technical Expertise)

Definition : A person who, by possession of a recognized degree, certificate, or professional standing, or who by extensive knowledge, training, and experience, has successfully demonstrated their ability to solve or resolve problems relating to the subject matter, the work, or the project.

Responsibilities under Subpart L :

Designing scaffolds, including structural calculations, load paths, and component specifications.

Designing suspension scaffold outriggers, tiebacks, and counterweight systems.

Designing custom or non-standard scaffolds.

Special Rule : Scaffolds exceeding 125 feet in height must be designed by a Registered Professional Engineer (RPE), who is a specialized Qualified Person.

The Competent Person (Inspection & Field Supervision)

Definition : A person who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.

Responsibilities under Subpart L :

Inspections : Must inspect scaffolds and scaffold components for visible defects before each work shift, and after any occurrence that could affect structural integrity (e.g., high winds, equipment collisions).

Supervision : Must supervise the erection, dismantling, altering, or moving of all scaffolds.

Fall Protection for Erectors/Dismantlers : Must determine the feasibility and safety of providing fall protection and access for employees erecting or dismantling scaffolds.

Weather Calls : Must determine if it is safe for employees to work on scaffolds during storms or high winds.

Training : Must train employees who erect, disassemble, move, operate, repair, maintain, or inspect scaffolds. (Note: Daily users of scaffolds can be trained by a competent person or qualified person, but erectors and dismantlers must be trained by a competent person).

Scaffold Inspection Checklist for the Competent Person

A competent person's daily inspection should include checking:

Mud sills are present and stable on the ground.

Base plates are secured to the frames and mud sills.

Screw jacks are adjusted properly and not overextended.

Frames are plumb, level, and free of bends or cracks.

Crossbraces are in place and pinned at all connections.

Scaffold ties are installed at the required vertical and horizontal intervals (4:1 ratio followed).

Planking is fully decking the platform with no gaps > 1 inch.

Plank overhang is between 6 and 12/18 inches, and overlap is at least 12 inches over supports.

Guardrail systems (toprails, midrails, toeboards) are complete and secure.

Access ladders or stair towers are properly attached and secure.

Power line clearances are maintained (minimum 10 feet for lines up to 50 kV).

Comparison Table of Competent vs. Qualified Person Responsibilities

  • Responsibility Competent Person Qualified Person Registered Professional Engineer (RPE)
  • Inspect scaffolds before each shift Yes No No
  • Supervise erection/dismantling Yes No No
  • Determine feasibility of fall protection during erection Yes No No
  • Make weather safety calls (high winds) Yes No No
  • Design suspension outriggers No Yes No
  • Design scaffold systems > 125 ft No No Yes
  • Solve engineering/structural issues No Yes Yes