Study guide
8.4 Arc Flash Hazards, Personal Protective Equipment & Rubber Insulating Gloves
OSHA 511 Occupational Safety and Health Standards for General Industry Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: OSH Act, Regulatory Framework & Inspection Procedures
1.1 OSH Act Purpose, Scope & General Duty Clause 1.2 OSHA Inspections, Priorities & Inspector Credentials 1.3 Citation Categories, Penalty Calculations & Contesting Procedures 1.4 Employer Rights, Employee Rights & Whistleblower Protections 1.5 Navigating 29 CFR: Standards Organization, Codification & Rulemaking 1.6 Safety & Health Programs, Cooperative Programs & Multi-Employer Worksites
2 Chapter 2: OSHA Recordkeeping & Reporting (29 CFR Part 1904)
2.1 Recording Criteria, Exclusions & First Aid vs. Medical Treatment 2.2 OSHA Recordkeeping Forms (Forms 300, 300A, 301) & Annual Summary Posting 2.3 Severe Injury Reporting Timelines, Privacy Cases & Electronic Submission
3 Chapter 3: Walking-Working Surfaces & Emergency Preparedness (Subparts D & E)
3.1 General Walking-Working Surface Requirements & Housekeeping (1910.22) 3.2 Ladders, Stairways, Scaffolds & Dockboards (1910.23-26) 3.3 Fall Protection Systems, Falling Object Protection & Training (1910.28-30) 3.4 Exit Routes, Emergency Action Plans (EAPs) & Fire Prevention Plans (1910.34-39) 3.5 Fire Protection (Subpart L): Extinguishers, Fixed Systems, Detection & Employee Alarms (1910.155-1910.165)
4 Chapter 4: Hazard Communication & GHS Standard (29 CFR 1910.1200)
4.1 Hazard Communication Standard Overview & Written HazCom Program 4.2 GHS Chemical Hazard Classification & Physical vs. Health Hazards 4.3 GHS Labels, Signal Words & 9 GHS Pictograms 4.4 Safety Data Sheets (16-Section SDS Format) & Employee Information/Training
5 Chapter 5: Personal Protective Equipment & Respiratory Protection (Subpart I)
5.1 Hierarchy of Controls & Hazard Assessment Certification (1910.132) 5.2 Eye, Face, Head, Foot & Hand Protection Standards (1910.133-138) 5.3 Respiratory Protection Program, Fit Testing & Medical Evaluations (1910.134) 5.4 Assigned Protection Factors (APFs), Maximum Use Concentrations & Respirator Selection
6 Chapter 6: Control of Hazardous Energy / Lockout/Tagout (29 CFR 1910.147)
6.1 Energy Control Program & Authorized vs. Affected Employee Roles 6.2 Lockout/Tagout Procedural Steps & Stored Energy Isolation 6.3 Special LOTO Situations: Group LOTO, Shift Changes & Outside Contractors 6.4 Periodic Annual Inspection, LOTO Hardware & Removal of Energy Controls
7 Chapter 7: Permit-Required Confined Spaces (29 CFR 1910.146)
7.1 Confined Space vs. Permit-Required Confined Space (PRCS) Identification 7.2 Atmospheric Testing Sequence, Testing Equipment & Acceptable Limits 7.3 PRCS Entry Roles: Entrant, Attendant, Entry Supervisor & Permit System 7.4 Non-Entry Rescue, Retrieval Systems & Emergency Response Services
8 Chapter 8: Electrical Safety & Safe Work Practices (Subpart S)
8.1 General Electrical Safety, NRTL Listing & Equipment Guarding (1910.303) 8.2 System Grounding, Ground-Fault Circuit Interrupters (GFCIs) & Wiring (1910.304-305) 8.3 Electrical Safe Work Practices, Qualified Persons & Approach Boundaries (1910.331-335) 8.4 Arc Flash Hazards, Personal Protective Equipment & Rubber Insulating Gloves
9 Chapter 9: Machine Guarding & Materials Handling (Subparts N & O)
9.1 General Machine Guarding Requirements & Safeguard Types (1910.212) 9.2 Mechanical Power Presses, Point of Operation & Power Transmission Guarding (1910.217, 1910.219) 9.3 Powered Industrial Trucks (Forklifts): Operator Training, Retraining & Safe Operation (1910.178) 9.4 Materials Handling, Storage, Slings & Overhead Cranes (1910.176, 1910.179, 1910.184) 9.5 Hand & Portable Powered Tools (Subpart P, 1910.241-1910.244)
10 Chapter 10: Occupational Health, Industrial Hygiene & Process Safety (Subparts G & Z)
10.1 Occupational Noise Exposure, Sound Levels & Hearing Conservation Program (1910.95) 10.2 Toxic & Hazardous Substances, Table Z-1 PELs & Industrial Hygiene Paradigm (1910.1000) 10.3 Specific Health Standards: Asbestos, Lead, Bloodborne Pathogens & Methylene Chloride 10.4 Process Safety Management (PSM) of Highly Hazardous Chemicals (1910.119 - 14 Elements) 10.5 Flammable Liquids (1910.106) & Welding, Cutting, and Brazing Safety (1910.252) 10.6 Hazardous Materials (Subpart H): Compressed Gases, Spray Finishing & HAZWOPER (1910.101, 1910.107, 1910.120) 10.7 General Environmental Controls & First Aid: Sanitation, Color Codes, Signs & Tags, Medical Services (Subparts J & K)
8.4 Arc Flash Hazards, Personal Protective Equipment & Rubber Insulating Gloves
Key Takeaways Explain This Topic AI
Arc flash hazards release extreme plasma temperatures (up to 35,000°F), explosive pressure waves (arc blast), and UV radiation, with an incident energy of 1.2 cal/cm² triggering second-degree skin burns.
Under 29 CFR 1910.137 and ASTM D120, rubber insulating gloves are classified into six voltage classes (Class 00 rated for 500V up to Class 4 rated for 36,000V).
Leather protector gloves must always be worn directly over rubber insulating gloves to provide vital physical protection against mechanical punctures, cuts, tears, and abrasions.
Under 1910.137(c)(2)(ii), rubber insulating gloves must be inspected for damage before each day's use and immediately after any incident suspected of causing damage, and gloves must be given an air test along with that inspection.
Under 29 CFR 1910.137(c)(2)(viii) and Table I-5, rubber insulating gloves must be electrically tested before first issue and every 6 months thereafter, while sleeves are tested before first issue and every 12 months thereafter.
Last updated: August 2026
- 8.4 Arc Flash Hazards, Personal Protective Equipment & Rubber Insulating Gloves
- Arc Flash and Arc Blast Physics
An Arc Flash is a dangerous explosive release of energy caused by an electric arc fault through air between phase conductors or between phase conductors and ground. Arc faults are typically initiated by accidental tool contact, dust accumulation, insulation breakdown, or equipment failure.
Severe Hazards Associated with Arc Flash Events:
Extreme Temperatures : Arc temperatures can reach 35,000°F (19,400°C) —four times hotter than the surface of the sun—instantaneously vaporizing copper conductors and steel enclosures.
Arc Blast Pressure Wave : Rapid thermal expansion of air creates explosive blast pressure waves exceeding 2,000 lbs/sq ft , capable of knocking technicians off ladders and destroying switchgear walls.
Molten Metal Shrapnel : Vaporized copper expands 67,000 times its solid volume, blasting molten droplets and metal shrapnel outward at speeds exceeding 700 mph.
Intense UV & Acoustic Energy : High-intensity ultraviolet radiation causes instantaneous blindness, accompanied by sound pressure levels exceeding 160 decibels (dB) , causing permanent eardrum rupture.
Incident Energy and Arc Flash Boundaries
Incident Energy is the amount of thermal energy impressed on a surface at a specified distance from an electrical arc fault, measured in calories per square centimeter ( c a l / c m 2 cal/cm^2 c a l / c m 2 ) .
The Second-Degree Burn Threshold
In electrical safety standards (NFPA 70E / OSHA 1910.335), an incident energy level of 1.2 cal/cm 2 1.2\text{ cal/cm}^2 1.2 cal/cm 2 represents the exact threshold for the onset of a second-degree burn on unprotected human skin (equivalent to holding a finger in the flame of a cigarette lighter for one second).
The Arc Flash Boundary
The Arc Flash Boundary is defined as the physical distance from an arc source at which potential incident energy equals 1.2 cal/cm 2 1.2\text{ cal/cm}^2 1.2 cal/cm 2 . Anyone working inside the Arc Flash Boundary MUST wear arc-rated personal protective equipment (PPE) .
Electrical Personal Protective Equipment (1910.335 & NFPA 70E)
Under 29 CFR 1910.335 , employees working in areas where electrical hazards exist must be provided with, and use, protective equipment designed and constructed for the specific body part to be protected.
Head, Eye, and Body Protection Criteria:
Non-Conductive Head Protection : Class E hard hats (tested to 20,000 volts) are required for high-voltage shock exposure. Class G (2,200V) hard hats provide limited protection. Class C (conductive) hard hats are strictly prohibited .
Eye & Face Protection : Arc-rated face shields combined with safety glasses must be worn whenever there is an arc flash hazard. Face shields must be rated for the incident energy ( c a l / c m 2 cal/cm^2 c a l / c m 2 ).
Arc-Rated (FR) Clothing : Flame-resistant clothing (NOMEX, treated cotton) rated in c a l / c m 2 cal/cm^2 c a l / c m 2 must cover all exposed skin. Outer garments must match or exceed the PPE category requirement (Categories 1 through 4, ranging from 4 c a l / c m 2 4\ cal/cm^2 4 c a l / c m 2 to 40 c a l / c m 2 40\ cal/cm^2 40 c a l / c m 2 ).
Undergarment Restrictions : Undergarments made of synthetic materials (nylon, polyester, rayon, spandex) are strictly prohibited under 1910.335 because they melt directly into human skin during an arc flash thermal event. Only 100% natural fibers (cotton, wool) are permitted.
Rubber Insulating Gloves: Voltage Classification (1910.137 / ASTM D120)
Rubber insulating gloves are the primary defense against electrical shock. Governed by 29 CFR 1910.137 and ASTM D120 , rubber gloves are divided into six distinct voltage classes, designated by color-coded cuffs and labels:
- Glove Class Color Label Maximum Use Voltage (AC) Proof Test Voltage (AC)
- Class 00 Beige 500 Volts 2,500 Volts
- Class 0 Red 1,000 Volts 5,000 Volts
- Class 1 White 7,500 Volts 10,000 Volts
- Class 2 Yellow 17,000 Volts 20,000 Volts
- Class 3 Green 26,500 Volts 30,000 Volts
Class 4 Orange 36,000 Volts 40,000 Volts MEMORY TIP FOR GLOVE CLASSES:
- Class 00 = 500V (Beige) | Class 0 = 1,000V (Red) | Class 1 = 7,500V (White)
- Class 2 = 17,000V (Yel) | Class 3 = 26,500V (Grn) | Class 4 = 36,000V (Org)
- Mandatory Leather Protectors (1910.137(c)(2)(vii))
Rubber insulating gloves are highly vulnerable to mechanical damage. Under 29 CFR 1910.137(c)(2)(vii) , leather protector gloves must ALWAYS be worn over rubber insulating gloves .
Mechanical Defense : Leather protectors protect the soft rubber underneath from punctures, abrasions, metal burrs, cuts, and tears.
Dielectric Function : Leather protectors offer zero electrical insulation by themselves; their sole function is mechanical preservation of the rubber dielectric barrier.
Cuff Clearance : a minimum distance must be maintained between the cuff of the leather protector and the cuff of the rubber glove so that surface tracking cannot bridge the insulation. The required gap increases with the voltage class and is specified in the consensus standard ASTM F496 (in-service care of insulating gloves and sleeves) rather than in the text of 1910.137 itself.
Daily Inspection and Air Testing Protocols (1910.137(c)(2)(ii))
Rubber insulating gloves must be inspected for flaws before each day's use and immediately following any situation where damage is suspected.
Air Testing Procedure
In addition to visual inspection, rubber gloves must undergo a mandatory air test prior to daily use:
Manual Air Inflation : The cuff of the glove is rolled tightly toward the fingers to trap air inside, or a portable manual air pump/glove inflator is utilized.
Pinch & Listen : The inflated glove is held near the technician's ear and cheek to check for escaping air, listening for faint hissing sounds and feeling for air leakage.
Inspection of Stretched Rubber : Inflation stretches the rubber, making microscopic pinholes, ozone cuts, embedded wood splinters, or chemical cracks readily visible.
Rejection : Any glove exhibiting air leakage, ozone checking, swelling, or embedded debris must be removed from service immediately.
Periodic Laboratory Electrical Re-Testing (1910.137(c)(2)(viii))
Visual and air testing cannot verify the ongoing dielectric breakdown strength of rubber insulation. OSHA standard 29 CFR 1910.137(c)(2)(viii) mandates periodic laboratory electrical re-testing:
Mandatory Testing Intervals:
Gloves In Active Service : Must be electrically re-tested in an accredited laboratory at least once every 6 months .
Tested but Not Yet Issued : insulating equipment that has been electrically tested but not issued for service may not be placed into service unless it has been electrically tested within the previous 12 months .
Sleeves : rubber insulating sleeves follow a longer cycle - before first issue and every 12 months thereafter.
Additional triggers : retesting is also required upon any indication that the insulating value is suspect, after repair, and - for gloves - after any use without protectors .
Stamp Requirements : Upon passing laboratory high-voltage proof testing, the glove cuff must be stamped with the test date or re-test expiration date .
Storage and Care Directives
Rubber insulating equipment must be stored in a manner that prevents environmental degradation:
Storage Location : Stored flat or cuff-down inside heavy canvas glove storage bags.
Prohibited Conditions : Must be kept away from direct sunlight (UV degradation), extreme heat, ozone (electric motors/transformers), moisture, and petroleum-based solvents/oils.