Study guide

4.2 GHS Chemical Hazard Classification & Physical vs. Health Hazards

OSHA 511 Occupational Safety and Health Standards for General Industry Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: OSH Act, Regulatory Framework & Inspection Procedures

1.1 OSH Act Purpose, Scope & General Duty Clause 1.2 OSHA Inspections, Priorities & Inspector Credentials 1.3 Citation Categories, Penalty Calculations & Contesting Procedures 1.4 Employer Rights, Employee Rights & Whistleblower Protections 1.5 Navigating 29 CFR: Standards Organization, Codification & Rulemaking 1.6 Safety & Health Programs, Cooperative Programs & Multi-Employer Worksites

2 Chapter 2: OSHA Recordkeeping & Reporting (29 CFR Part 1904)

2.1 Recording Criteria, Exclusions & First Aid vs. Medical Treatment 2.2 OSHA Recordkeeping Forms (Forms 300, 300A, 301) & Annual Summary Posting 2.3 Severe Injury Reporting Timelines, Privacy Cases & Electronic Submission

3 Chapter 3: Walking-Working Surfaces & Emergency Preparedness (Subparts D & E)

3.1 General Walking-Working Surface Requirements & Housekeeping (1910.22) 3.2 Ladders, Stairways, Scaffolds & Dockboards (1910.23-26) 3.3 Fall Protection Systems, Falling Object Protection & Training (1910.28-30) 3.4 Exit Routes, Emergency Action Plans (EAPs) & Fire Prevention Plans (1910.34-39) 3.5 Fire Protection (Subpart L): Extinguishers, Fixed Systems, Detection & Employee Alarms (1910.155-1910.165)

4 Chapter 4: Hazard Communication & GHS Standard (29 CFR 1910.1200)

4.1 Hazard Communication Standard Overview & Written HazCom Program 4.2 GHS Chemical Hazard Classification & Physical vs. Health Hazards 4.3 GHS Labels, Signal Words & 9 GHS Pictograms 4.4 Safety Data Sheets (16-Section SDS Format) & Employee Information/Training

5 Chapter 5: Personal Protective Equipment & Respiratory Protection (Subpart I)

5.1 Hierarchy of Controls & Hazard Assessment Certification (1910.132) 5.2 Eye, Face, Head, Foot & Hand Protection Standards (1910.133-138) 5.3 Respiratory Protection Program, Fit Testing & Medical Evaluations (1910.134) 5.4 Assigned Protection Factors (APFs), Maximum Use Concentrations & Respirator Selection

6 Chapter 6: Control of Hazardous Energy / Lockout/Tagout (29 CFR 1910.147)

6.1 Energy Control Program & Authorized vs. Affected Employee Roles 6.2 Lockout/Tagout Procedural Steps & Stored Energy Isolation 6.3 Special LOTO Situations: Group LOTO, Shift Changes & Outside Contractors 6.4 Periodic Annual Inspection, LOTO Hardware & Removal of Energy Controls

7 Chapter 7: Permit-Required Confined Spaces (29 CFR 1910.146)

7.1 Confined Space vs. Permit-Required Confined Space (PRCS) Identification 7.2 Atmospheric Testing Sequence, Testing Equipment & Acceptable Limits 7.3 PRCS Entry Roles: Entrant, Attendant, Entry Supervisor & Permit System 7.4 Non-Entry Rescue, Retrieval Systems & Emergency Response Services

8 Chapter 8: Electrical Safety & Safe Work Practices (Subpart S)

8.1 General Electrical Safety, NRTL Listing & Equipment Guarding (1910.303) 8.2 System Grounding, Ground-Fault Circuit Interrupters (GFCIs) & Wiring (1910.304-305) 8.3 Electrical Safe Work Practices, Qualified Persons & Approach Boundaries (1910.331-335) 8.4 Arc Flash Hazards, Personal Protective Equipment & Rubber Insulating Gloves

9 Chapter 9: Machine Guarding & Materials Handling (Subparts N & O)

9.1 General Machine Guarding Requirements & Safeguard Types (1910.212) 9.2 Mechanical Power Presses, Point of Operation & Power Transmission Guarding (1910.217, 1910.219) 9.3 Powered Industrial Trucks (Forklifts): Operator Training, Retraining & Safe Operation (1910.178) 9.4 Materials Handling, Storage, Slings & Overhead Cranes (1910.176, 1910.179, 1910.184) 9.5 Hand & Portable Powered Tools (Subpart P, 1910.241-1910.244)

10 Chapter 10: Occupational Health, Industrial Hygiene & Process Safety (Subparts G & Z)

10.1 Occupational Noise Exposure, Sound Levels & Hearing Conservation Program (1910.95) 10.2 Toxic & Hazardous Substances, Table Z-1 PELs & Industrial Hygiene Paradigm (1910.1000) 10.3 Specific Health Standards: Asbestos, Lead, Bloodborne Pathogens & Methylene Chloride 10.4 Process Safety Management (PSM) of Highly Hazardous Chemicals (1910.119 - 14 Elements) 10.5 Flammable Liquids (1910.106) & Welding, Cutting, and Brazing Safety (1910.252) 10.6 Hazardous Materials (Subpart H): Compressed Gases, Spray Finishing & HAZWOPER (1910.101, 1910.107, 1910.120) 10.7 General Environmental Controls & First Aid: Sanitation, Color Codes, Signs & Tags, Medical Services (Subparts J & K)

4.2 GHS Chemical Hazard Classification & Physical vs. Health Hazards

Key Takeaways Explain This Topic AI

OSHA updated 29 CFR 1910.1200 in 2012 to align with the United Nations Globally Harmonized System of Classification and Labelling of Chemicals (GHS).

GHS hazard classification establishes specific criteria for physical hazard classes (16 classes under Appendix B) and health hazard classes (10 classes under Appendix A).

Within GHS hazard classes, Hazard Categories indicate the degree of severity, where Category 1 ALWAYS represents the most severe hazard, and higher numbers (Category 4 or 5) represent lower severity.

GHS numerical hazard categories operate in direct opposition to traditional NFPA 704 and HMIS systems, where 4 represents the most severe hazard and 0 represents minimal hazard.

OSHA's HazCom standard includes specialized hazard classifications such as Combustible Dust, Pyrophoric Gas, Simple Asphyxiants, and Hazards Not Otherwise Classified (HNOC).

Last updated: August 2026

  • 4.2 GHS Chemical Hazard Classification & Physical vs. Health Hazards
  • The GHS Classification Framework

Prior to the 2012 GHS alignment, 29 CFR 1910.1200 relied on performance-oriented definitions where chemical manufacturers evaluated toxicological data using varying subjective thresholds. Under the GHS framework, chemical hazard classification is strictly criterion-based . Manufacturers and importers must compare empirical physical test data and toxicological study results against detailed statutory benchmarks defined in 29 CFR 1910.1200 Appendix A (Health Hazards) and Appendix B (Physical Hazards) .

Two fundamental structural terms govern GHS chemical classification:

Hazard Class : Describes the nature of the physical or health hazard (e.g., Flammable Liquid, Carcinogenicity, Acute Toxicity, Corrosive to Metals).

Hazard Category : Defines the numerical or alphabetical sub-division within a hazard class that expresses the relative severity of the hazard.

Critical Distinction: GHS Hazard Categories vs. NFPA 704 / HMIS Systems

A primary source of confusion for safety managers and workers is the inverse numerical relationship between GHS Hazard Categories and legacy rating systems such as the National Fire Protection Association (NFPA 704) diamond and the Hazardous Materials Identification System (HMIS) color bars.

CRITICAL RULE : In GHS (29 CFR 1910.1200), Category 1 is ALWAYS the most severe hazard within a hazard class. As the category number increases (Category 2, Category 3, Category 4), the hazard severity decreases .

  • Classification System Rating Scale Range Most Severe Rating Least Severe Rating
  • GHS (29 CFR 1910.1200) Category 1 to 4 (or 5) Category 1 (Highest Severity) Category 4 / 5 (Lowest Severity)
  • NFPA 704 Standard Rating 0 to 4 Rating 4 (Extreme Hazard) Rating 0 (Minimal Hazard)
  • HMIS System Rating 0 to 4 Rating 4 (Severe Hazard) Rating 0 (Minimal Hazard)

Because NFPA 4 represents severe fire/health danger while GHS Category 4 represents low danger, employers must train workers thoroughly to prevent dangerous misinterpretations when reviewing SDSs or workplace placards.

Health Hazard Classification (29 CFR 1910.1200 Appendix A)

Appendix A sets forth mandatory scientific criteria for classifying chemical health hazards across 10 distinct classes:

1. Acute Toxicity (Appendix A.1)

Refers to adverse effects occurring following oral or dermal administration of a single dose, multiple doses within 24 hours, or an inhalation exposure of 4 hours. Classified into Categories 1 through 4 based on LD50 (lethal dose for 50% of test animals in mg/kg body weight) or LC50 (lethal concentration in ppm or mg/L):

Category 1 : Oral LD50 ≤ 5 mg/kg; Inhalation gas LC50 ≤ 100 ppm (Fatal if swallowed/inhaled).

Category 4 : Oral LD50 300 to 2000 mg/kg; Inhalation gas LC50 2500 to 20000 ppm (Harmful if swallowed/inhaled).

2. Skin Corrosion / Irritation (Appendix A.2)

Skin Corrosion (Category 1A, 1B, 1C) : Production of irreversible skin damage (visible necrosis through the epidermis into the dermis) following exposure up to 4 hours.

Skin Irritation (Category 2) : Production of reversible inflammatory skin damage following exposure up to 4 hours.

3. Serious Eye Damage / Eye Irritation (Appendix A.3)

Category 1 (Serious Eye Damage) : Irreversible tissue damage or severe physical decay of vision.

Category 2 / 2A / 2B (Eye Irritation) : Reversible changes to the eye clearing within 21 days.

4. Respiratory or Skin Sensitization (Appendix A.4)

Respiratory Sensitizer (Category 1) : Chemical that induces hyper-responsiveness of the airways (asthma, severe dyspnea) following inhalation.

Skin Sensitizer (Category 1) : Chemical that induces an allergic response following skin contact (allergic contact dermatitis).

5. Germ Cell Mutagenicity (Appendix A.5)

Chemicals causing heritable gene mutations in human germ cells (Category 1A known, 1B presumed, Category 2 suspected).

6. Carcinogenicity (Appendix A.6)

Chemicals that induce cancer or increase its incidence:

Category 1A : Known to have carcinogenic potential for humans based on human epidemiological evidence.

Category 1B : Presumed to have carcinogenic potential for humans based on animal studies.

Category 2 : Suspected human carcinogen (limited evidence).

7. Reproductive Toxicity (Appendix A.7)

Adverse effects on sexual function and fertility in adult males/females, or developmental toxicity in offspring.

8. Specific Target Organ Toxicity — Single Exposure (STOT-SE) (Appendix A.8)

Specific, non-lethal target organ toxicity arising from a single exposure (e.g., liver necrosis, kidney damage). Category 1 (severe effect), Category 2 (significant effect), Category 3 (transient narcotic effects or respiratory tract irritation).

9. Specific Target Organ Toxicity — Repeated Exposure (STOT-RE) (Appendix A.9)

Target organ damage resulting from repeated or prolonged exposure (e.g., silicosis, chronic painter's encephalopathy).

10. Aspiration Hazard (Appendix A.10)

Chemicals causing severe pulmonary injury or chemical pneumonitis if aspirated into the trachea and lower respiratory tract (e.g., low-viscosity liquid hydrocarbons).

Physical Hazard Classification (29 CFR 1910.1200 Appendix B)

Appendix B establishes classification criteria for the 16 physical hazard classes (B.1 through B.16) , based on intrinsic chemical and thermodynamic properties. The groupings below cover all sixteen:

Explosives (Appendix B.1) : Solid or liquid substances (or mixtures) capable on their own of producing gas at such a temperature, pressure, and speed as to cause damage to the surroundings. Subdivided into Divisions 1.1 through 1.6 by mass-explosion, projection, fire, and insensitivity hazard. Unstable explosives and Divisions 1.1–1.3 carry the Exploding Bomb pictogram with the signal word Danger . The 2024 HazCom update added desensitized explosives — explosives wetted or diluted to suppress their explosive properties — as a separate class.

Flammable Liquids : Classified by Flash Point (FP) and Initial Boiling Point (IBP) :

  • Category 1 : FP < 23°C (73.4°F) and IBP ≤ 35°C (95°F) (e.g., diethyl ether, pentane)
  • Category 2 : FP < 23°C (73.4°F) and IBP > 35°C (95°F) (e.g., acetone, ethanol, toluene)
  • Category 3 : FP ≥ 23°C (73.4°F) and ≤ 60°C (140°F) (e.g., mineral spirits, xylene)
  • Category 4 : FP > 60°C (140°F) and ≤ 93°C (199.4°F) (e.g., diesel fuel, fuel oil)

Flammable Gases & Aerosols : Gases having a flammable range with air at 20°C and 101.3 kPa.

Oxidizing Gases, Liquids, Solids : Substances that yield oxygen or cause/contribute to the combustion of other material more than air does.

Gases Under Pressure : Compressed, liquefied, refrigerated liquefied, or dissolved gases stored at ≥ 200 kPa gauge pressure.

Pyrophoric Liquids, Solids & Gases : Substances liable to ignite within 5 minutes after coming into contact with air without an external ignition source.

Self-Heating Substances : Solid/liquid substances liable to self-heat by reaction with air without energy supply.

Substances emitting Flammable Gases upon Contact with Water : React spontaneously with water to emit flammable gases.

Organic Peroxides & Self-Reactive Substances : Thermally unstable organic substances subject to exothermic decomposition (Types A through G).

Corrosive to Metals : Chemicals that by chemical action will materially damage or destroy metals (corrosion rate on steel/aluminum > 6.25 mm/year at 55°C).

OSHA Specific Physical Hazards :

Combustible Dust : Finely divided solid particles suspended in air that present a fire or explosion hazard.

Pyrophoric Gas : Flammable gas that ignites spontaneously in air at or below 54.4°C (130°F).

Simple Asphyxiant : Vapor/gas that displaces oxygen in air, causing rapid suffocation (e.g., nitrogen, argon, helium).

Hazards Not Otherwise Classified (HNOC) : Adverse physical or health hazards established by scientific evidence that do not fall into defined GHS hazard classes.