Study guide

10.5 Flammable Liquids (1910.106) & Welding, Cutting, and Brazing Safety (1910.252)

OSHA 511 Occupational Safety and Health Standards for General Industry Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: OSH Act, Regulatory Framework & Inspection Procedures

1.1 OSH Act Purpose, Scope & General Duty Clause 1.2 OSHA Inspections, Priorities & Inspector Credentials 1.3 Citation Categories, Penalty Calculations & Contesting Procedures 1.4 Employer Rights, Employee Rights & Whistleblower Protections 1.5 Navigating 29 CFR: Standards Organization, Codification & Rulemaking 1.6 Safety & Health Programs, Cooperative Programs & Multi-Employer Worksites

2 Chapter 2: OSHA Recordkeeping & Reporting (29 CFR Part 1904)

2.1 Recording Criteria, Exclusions & First Aid vs. Medical Treatment 2.2 OSHA Recordkeeping Forms (Forms 300, 300A, 301) & Annual Summary Posting 2.3 Severe Injury Reporting Timelines, Privacy Cases & Electronic Submission

3 Chapter 3: Walking-Working Surfaces & Emergency Preparedness (Subparts D & E)

3.1 General Walking-Working Surface Requirements & Housekeeping (1910.22) 3.2 Ladders, Stairways, Scaffolds & Dockboards (1910.23-26) 3.3 Fall Protection Systems, Falling Object Protection & Training (1910.28-30) 3.4 Exit Routes, Emergency Action Plans (EAPs) & Fire Prevention Plans (1910.34-39) 3.5 Fire Protection (Subpart L): Extinguishers, Fixed Systems, Detection & Employee Alarms (1910.155-1910.165)

4 Chapter 4: Hazard Communication & GHS Standard (29 CFR 1910.1200)

4.1 Hazard Communication Standard Overview & Written HazCom Program 4.2 GHS Chemical Hazard Classification & Physical vs. Health Hazards 4.3 GHS Labels, Signal Words & 9 GHS Pictograms 4.4 Safety Data Sheets (16-Section SDS Format) & Employee Information/Training

5 Chapter 5: Personal Protective Equipment & Respiratory Protection (Subpart I)

5.1 Hierarchy of Controls & Hazard Assessment Certification (1910.132) 5.2 Eye, Face, Head, Foot & Hand Protection Standards (1910.133-138) 5.3 Respiratory Protection Program, Fit Testing & Medical Evaluations (1910.134) 5.4 Assigned Protection Factors (APFs), Maximum Use Concentrations & Respirator Selection

6 Chapter 6: Control of Hazardous Energy / Lockout/Tagout (29 CFR 1910.147)

6.1 Energy Control Program & Authorized vs. Affected Employee Roles 6.2 Lockout/Tagout Procedural Steps & Stored Energy Isolation 6.3 Special LOTO Situations: Group LOTO, Shift Changes & Outside Contractors 6.4 Periodic Annual Inspection, LOTO Hardware & Removal of Energy Controls

7 Chapter 7: Permit-Required Confined Spaces (29 CFR 1910.146)

7.1 Confined Space vs. Permit-Required Confined Space (PRCS) Identification 7.2 Atmospheric Testing Sequence, Testing Equipment & Acceptable Limits 7.3 PRCS Entry Roles: Entrant, Attendant, Entry Supervisor & Permit System 7.4 Non-Entry Rescue, Retrieval Systems & Emergency Response Services

8 Chapter 8: Electrical Safety & Safe Work Practices (Subpart S)

8.1 General Electrical Safety, NRTL Listing & Equipment Guarding (1910.303) 8.2 System Grounding, Ground-Fault Circuit Interrupters (GFCIs) & Wiring (1910.304-305) 8.3 Electrical Safe Work Practices, Qualified Persons & Approach Boundaries (1910.331-335) 8.4 Arc Flash Hazards, Personal Protective Equipment & Rubber Insulating Gloves

9 Chapter 9: Machine Guarding & Materials Handling (Subparts N & O)

9.1 General Machine Guarding Requirements & Safeguard Types (1910.212) 9.2 Mechanical Power Presses, Point of Operation & Power Transmission Guarding (1910.217, 1910.219) 9.3 Powered Industrial Trucks (Forklifts): Operator Training, Retraining & Safe Operation (1910.178) 9.4 Materials Handling, Storage, Slings & Overhead Cranes (1910.176, 1910.179, 1910.184) 9.5 Hand & Portable Powered Tools (Subpart P, 1910.241-1910.244)

10 Chapter 10: Occupational Health, Industrial Hygiene & Process Safety (Subparts G & Z)

10.1 Occupational Noise Exposure, Sound Levels & Hearing Conservation Program (1910.95) 10.2 Toxic & Hazardous Substances, Table Z-1 PELs & Industrial Hygiene Paradigm (1910.1000) 10.3 Specific Health Standards: Asbestos, Lead, Bloodborne Pathogens & Methylene Chloride 10.4 Process Safety Management (PSM) of Highly Hazardous Chemicals (1910.119 - 14 Elements) 10.5 Flammable Liquids (1910.106) & Welding, Cutting, and Brazing Safety (1910.252) 10.6 Hazardous Materials (Subpart H): Compressed Gases, Spray Finishing & HAZWOPER (1910.101, 1910.107, 1910.120) 10.7 General Environmental Controls & First Aid: Sanitation, Color Codes, Signs & Tags, Medical Services (Subparts J & K)

10.5 Flammable Liquids (1910.106) & Welding, Cutting, and Brazing Safety (1910.252)

Key Takeaways Explain This Topic AI

OSHA 29 CFR 1910.106 classifies flammable liquids into four Categories based on flash point and boiling point, aligning with the Globally Harmonized System (GHS).

Portable storage of flammable liquids requires approved safety cans of no more than 5 gallons capacity equipped with spring-closing caps, flame arrestor screens, and pressure relief.

Storage cabinet limits under 1910.106 prohibit storing more than 60 gallons of Category 1, 2, or 3 flammable liquids, or 120 gallons of Category 4 flammable liquids in a single cabinet.

OSHA 29 CFR 1910.252 mandates a fire watch whenever hot work occurs within 35 feet of exposed combustibles, with the fire watch maintained for at least 30 minutes post-completion.

Oxygen cylinders in storage must be separated from fuel-gas cylinders or combustible materials by at least 20 feet or by a 5-foot noncombustible barrier with a 1/2-hour fire rating, with valve caps secured.

Last updated: August 2026

Industrial facilities utilize flammable liquids and hot work operations daily. Improper handling of flammable liquids under 29 CFR 1910.106 or unsafe welding and cutting practices under 29 CFR 1910.252 / 1910.253 creates high-consequence fire and explosion risks. Safety professionals must understand GHS flammable liquid classifications, safety container design, storage cabinet volume thresholds, grounding/bonding principles, 35-foot fire clearance rules, 30-minute fire watch mandates, and gas cylinder separation standards.

1. Flammable Liquids Classification (29 CFR 1910.106)

OSHA aligned 29 CFR 1910.106 with the Globally Harmonized System (GHS), categorizing flammable liquids into four distinct categories based on Flash Point (FP) and Boiling Point (BP) .

Flammable Liquid Category Classifications

  • Category Flash Point (FP) Thresholds Boiling Point (BP) Thresholds Representative Examples
  • Category 1 FP < 23 °C (73.4 °F) BP ≤ \le ≤ 35 °C (95 °F) Diethyl ether, Pentane
  • Category 2 FP < 23 °C (73.4 °F) BP > 35 °C (95 °F) Acetone, Gasoline, Toluene
  • Category 3 FP ≥ \ge ≥ 23 °C (73.4 °F) and ≤ \le ≤ 60 °C (140 °F) Any BP Mineral spirits, Xylene, Diesel
  • Category 4 FP > 60 °C (140 °F) and ≤ \le ≤ 93 °C (199.4 °F) Any BP Heating oil, Naphthalene
  • 2. Portable Storage & Safety Cans (1910.106(a)(29))

When storing or transporting small quantities of flammable liquids, standard unapproved containers are strictly prohibited.

Safety Can Definition: An approved container of not more than 5 gallons (19 liters) capacity, having a spring-closing lid and spout cover, and so designed that it will safely relieve internal pressure when subjected to fire exposure (automatic pressure relief at 3 to 5 psi), equipped with a internal flame arrestor screen .

Flame Arrestor Function: A wire mesh screen inside the spout that dissipates heat energy, preventing an external flame from propagating into the vapor space of the container.

3. Storage Cabinet Specifications & Storage Limits (1910.106(d)(3))

Flammable storage cabinets protect internal containers from external fire exposure during an emergency.

Cabinet Construction: Double-walled 18-gauge sheet steel with a 1.5-inch insulating air space , or 1-inch thick approved exterior grade wood; 2-inch liquid-tight bottom sump to contain spills; 3-point door latching mechanism; labeled in conspicuous letters "FLAMMABLE - KEEP FIRE AWAY" .

Storage Limits per Cabinet:

Maximum 60 gallons of Category 1, Category 2, or Category 3 flammable liquids.

Maximum 120 gallons of Category 4 flammable liquids.

Fire Area Limits: No more than 3 storage cabinets may be located in a single fire area unless separated by at least 100 feet. +-------------------------------------------------------------+

  • | FLAMMABLE LIQUID STORAGE CABINET LIMITS |
  • +-------------------------------------------------------------+
  • | CATEGORY 1, 2, or 3 LIQUIDS: Max 60 Gallons per Cabinet |
  • | CATEGORY 4 LIQUIDS: Max 120 Gallons per Cabinet |
  • | |
  • | CONSTRUCTION: 18-gauge steel, 1.5-inch air space, 2-in sump|
  • +-------------------------------------------------------------+
  • 4. Grounding & Bonding during Transfer (1910.106(e)(6)(ii))

Static electricity generated during fluid flow through hoses and spouts can ignite flammable vapors. When dispensing Category 1 or 2 flammable liquids (or Category 3 with FP < 100 °F):

Bonding: Electrically connecting the dispensing container to the receiving container using a conductive wire/clamp to equalize electrical potential and eliminate static spark jumping between containers.

Grounding: Electrically connecting the dispensing container to a grounded building earth ground to drain accumulated static charge safely to the earth.

5. Welding, Cutting, and Brazing Safety (29 CFR 1910.252)

Hot work operations generate sparks, slag, and intense radiant heat capable of igniting structural fires hours after work ceases.

Fire Prevention & the 35-Foot Radius Clearance Rule (1910.252(a)(2))

35-Foot Rule: All combustible materials within a 35-foot (10.7 m) radius of the welding or cutting operation must be moved to a safe location. If relocation is impracticable, combustibles must be protected with flameproof covers, welding blankets, or metal guards. Floor openings or wall cracks within 35 feet must be tightly covered to prevent spark passage.

Fire Watch Mandate & 30-Minute Duration (1910.252(a)(2)(iii)(C))

Fire Watch Conditions: A dedicated fire watch is required whenever hot work is performed in locations where other than a minor fire might develop, OR when combustibles are within 35 feet, OR when wall/floor openings expose combustibles in adjacent areas.

Post-Operation Duration: The fire watch must be maintained for at least 30 minutes after completion of welding or cutting operations to detect and extinguish possible smoldering fires.

Fire Watch Duties: Dedicated personnel with suitable fire extinguishers, trained in sounding alarms and extinguishing fires.

6. Compressed Gas Cylinder Safety (29 CFR 1910.252 & 1910.253)

Oxy-fuel gas welding uses compressed oxygen and fuel gas (e.g., acetylene) under high pressure. Cylinder handling failure can cause rocketing cylinders or massive firestorms.

Cylinder Storage Separation Rule (1910.252 / 1910.253(b)(4)(iii))

Oxygen cylinders in storage must be separated from fuel-gas cylinders or combustible materials (especially oil, grease, or flammable liquids) by:

A minimum distance of 20 feet (6.1 meters) , OR

A noncombustible barrier at least 5 feet (1.5 meters) high having a fire-resistance rating of at least 1/2 hour (30 minutes).

Cylinder Handling & Storage Standards

Valve Protection Caps: Must be in place and hand-tight whenever cylinders are not in use, being moved, or connected for service.

Upright Securement: Cylinders must be stored upright (valve end up) and secured with chains, straps, or racks to prevent tipping. Acetylene cylinders must always be stored and operated in the vertical upright position to prevent acetone liquid from entering regulators and hose lines.

Separation from Heat: Cylinders must be kept away from radiators, furnace vents, and electrical circuits.