Study guide

1.2 OSHA Inspections, Priorities & Inspector Credentials

OSHA 511 Occupational Safety and Health Standards for General Industry Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: OSH Act, Regulatory Framework & Inspection Procedures

1.1 OSH Act Purpose, Scope & General Duty Clause 1.2 OSHA Inspections, Priorities & Inspector Credentials 1.3 Citation Categories, Penalty Calculations & Contesting Procedures 1.4 Employer Rights, Employee Rights & Whistleblower Protections 1.5 Navigating 29 CFR: Standards Organization, Codification & Rulemaking 1.6 Safety & Health Programs, Cooperative Programs & Multi-Employer Worksites

2 Chapter 2: OSHA Recordkeeping & Reporting (29 CFR Part 1904)

2.1 Recording Criteria, Exclusions & First Aid vs. Medical Treatment 2.2 OSHA Recordkeeping Forms (Forms 300, 300A, 301) & Annual Summary Posting 2.3 Severe Injury Reporting Timelines, Privacy Cases & Electronic Submission

3 Chapter 3: Walking-Working Surfaces & Emergency Preparedness (Subparts D & E)

3.1 General Walking-Working Surface Requirements & Housekeeping (1910.22) 3.2 Ladders, Stairways, Scaffolds & Dockboards (1910.23-26) 3.3 Fall Protection Systems, Falling Object Protection & Training (1910.28-30) 3.4 Exit Routes, Emergency Action Plans (EAPs) & Fire Prevention Plans (1910.34-39) 3.5 Fire Protection (Subpart L): Extinguishers, Fixed Systems, Detection & Employee Alarms (1910.155-1910.165)

4 Chapter 4: Hazard Communication & GHS Standard (29 CFR 1910.1200)

4.1 Hazard Communication Standard Overview & Written HazCom Program 4.2 GHS Chemical Hazard Classification & Physical vs. Health Hazards 4.3 GHS Labels, Signal Words & 9 GHS Pictograms 4.4 Safety Data Sheets (16-Section SDS Format) & Employee Information/Training

5 Chapter 5: Personal Protective Equipment & Respiratory Protection (Subpart I)

5.1 Hierarchy of Controls & Hazard Assessment Certification (1910.132) 5.2 Eye, Face, Head, Foot & Hand Protection Standards (1910.133-138) 5.3 Respiratory Protection Program, Fit Testing & Medical Evaluations (1910.134) 5.4 Assigned Protection Factors (APFs), Maximum Use Concentrations & Respirator Selection

6 Chapter 6: Control of Hazardous Energy / Lockout/Tagout (29 CFR 1910.147)

6.1 Energy Control Program & Authorized vs. Affected Employee Roles 6.2 Lockout/Tagout Procedural Steps & Stored Energy Isolation 6.3 Special LOTO Situations: Group LOTO, Shift Changes & Outside Contractors 6.4 Periodic Annual Inspection, LOTO Hardware & Removal of Energy Controls

7 Chapter 7: Permit-Required Confined Spaces (29 CFR 1910.146)

7.1 Confined Space vs. Permit-Required Confined Space (PRCS) Identification 7.2 Atmospheric Testing Sequence, Testing Equipment & Acceptable Limits 7.3 PRCS Entry Roles: Entrant, Attendant, Entry Supervisor & Permit System 7.4 Non-Entry Rescue, Retrieval Systems & Emergency Response Services

8 Chapter 8: Electrical Safety & Safe Work Practices (Subpart S)

8.1 General Electrical Safety, NRTL Listing & Equipment Guarding (1910.303) 8.2 System Grounding, Ground-Fault Circuit Interrupters (GFCIs) & Wiring (1910.304-305) 8.3 Electrical Safe Work Practices, Qualified Persons & Approach Boundaries (1910.331-335) 8.4 Arc Flash Hazards, Personal Protective Equipment & Rubber Insulating Gloves

9 Chapter 9: Machine Guarding & Materials Handling (Subparts N & O)

9.1 General Machine Guarding Requirements & Safeguard Types (1910.212) 9.2 Mechanical Power Presses, Point of Operation & Power Transmission Guarding (1910.217, 1910.219) 9.3 Powered Industrial Trucks (Forklifts): Operator Training, Retraining & Safe Operation (1910.178) 9.4 Materials Handling, Storage, Slings & Overhead Cranes (1910.176, 1910.179, 1910.184) 9.5 Hand & Portable Powered Tools (Subpart P, 1910.241-1910.244)

10 Chapter 10: Occupational Health, Industrial Hygiene & Process Safety (Subparts G & Z)

10.1 Occupational Noise Exposure, Sound Levels & Hearing Conservation Program (1910.95) 10.2 Toxic & Hazardous Substances, Table Z-1 PELs & Industrial Hygiene Paradigm (1910.1000) 10.3 Specific Health Standards: Asbestos, Lead, Bloodborne Pathogens & Methylene Chloride 10.4 Process Safety Management (PSM) of Highly Hazardous Chemicals (1910.119 - 14 Elements) 10.5 Flammable Liquids (1910.106) & Welding, Cutting, and Brazing Safety (1910.252) 10.6 Hazardous Materials (Subpart H): Compressed Gases, Spray Finishing & HAZWOPER (1910.101, 1910.107, 1910.120) 10.7 General Environmental Controls & First Aid: Sanitation, Color Codes, Signs & Tags, Medical Services (Subparts J & K)

1.2 OSHA Inspections, Priorities & Inspector Credentials

Key Takeaways Explain This Topic AI

OSHA establishes five strict enforcement priorities: Imminent Danger, Fatalities/Catastrophes, Complaints/Referrals, Targeted Inspections (SST/NEPs), and Follow-up Inspections.

Fatalities must be reported to OSHA within 8 hours; inpatient hospitalizations, amputations, or loss of an eye must be reported within 24 hours (29 CFR 1904.39).

Giving unauthorized advance notice of an OSHA inspection is a federal crime punishable by up to a $1,000 fine and/or 6 months imprisonment under 29 CFR 1903.6.

Inspections follow three distinct phases: Opening Conference, Walkaround Inspection, and Closing Conference.

Under Marshall v. Barlow's, Inc. (1978), employers have a Fourth Amendment right to demand an administrative search warrant before allowing an OSHA inspection.

Last updated: August 2026

  • 1.2 OSHA Inspections, Priorities & Inspector Credentials
  • OSHA Enforcement Priorities

Federal OSHA and its State Plan partners field roughly 1,850 inspectors covering about 130 million workers at more than 8 million worksites — approximately one compliance officer for every 70,000 workers (OSHA, Commonly Used Statistics ). Federal OSHA completed 34,696 inspections in FY 2024 . Because universal inspection is arithmetically impossible at that ratio, the agency rations enforcement resources through a strict five-tier priority framework.

Priority Level Enforcement Category Triggers & Regulatory Requirements

1st Priority Imminent Danger Top enforcement priority. Defined as any condition or practice where danger exists that could reasonably be expected to cause death or serious physical harm immediately or before the danger can be eliminated through normal enforcement. CSHOs request immediate voluntary abatement; if refused, OSHA petitions a federal district court for an emergency injunction under Section 13.

2nd Priority Fatalities & Catastrophes Second priority. Triggered by work-related incidents causing death or severe harm. Under 29 CFR 1904.39 , employers must report any work-related fatality within 8 hours , and any inpatient hospitalization, amputation, or loss of an eye within 24 hours to OSHA.

3rd Priority Complaints & Referrals Third priority. Formal written complaints submitted by current employees or their representatives alleging safety hazards (formal complaints trigger mandatory on-site inspections). Referrals from other agencies, media reports, or emergency first responders also trigger inspections.

4th Priority Targeted Inspections Fourth priority. Programmed inspections targeting high-hazard industries or facilities with high Days Away, Restricted, or Transferred (DART) rates. Driven by Site-Specific Targeting (SST) , National Emphasis Programs (NEPs) (e.g., trenching, combustible dust, heat illness, fall protection), and Local Emphasis Programs (LEPs) .

5th Priority Follow-up Inspections Fifth priority. Conducted to verify that previously cited violations have been abated by the employer, particularly following Serious, Willful, or Repeat citations.

READ THE CHART BELOW AS A SCHEMATIC : OSHA does not publish an official percentage breakdown of inspections by priority tier. The chart depicts relative enforcement emphasis only — memorize the order of the five priorities, not the percentages.

Advance Notice Restrictions (29 CFR 1903.6)

Under Section 17(f) of the OSH Act and 29 CFR 1903.6 , providing unauthorized advance notice of an OSHA inspection to an employer is strictly prohibited. The law imposes severe criminal penalties: anyone giving unauthorized advance notice is subject to a criminal fine of up to $1,000, imprisonment for up to 6 months, or both .

Advance notice may only be authorized by the OSHA Area Director under four narrow statutory exceptions:

In cases of imminent danger , to enable the employer to correct the hazard immediately.

Where the inspection must take place after regular business hours or requires special preparation.

Where advance notice is necessary to ensure the presence of employer and employee representatives or technical specialists.

In special situations where the Area Director determines that advance notice will produce a more thorough inspection.

CSHO Credentials and Entry Rights

When a CSHO arrives at a worksite, the inspection begins with credential verification. The CSHO must present official U.S. Department of Labor credentials containing a photograph and a unique serial number.

CRITICAL RULE : An inspector's badge or business card alone is not sufficient legal identification. Employers retain the right to verify credentials by calling the local OSHA Area Office before granting access.

Marshall v. Barlow's, Inc. (1978) — Warrants and Entry

In Marshall v. Barlow's, Inc. (436 U.S. 307), the U.S. Supreme Court held that employers have a Fourth Amendment constitutional right protecting against warrantless administrative searches.

An employer has the legal right to refuse entry to a CSHO and demand an administrative search warrant.

If refused entry, the CSHO reports to the OSHA Area Director, who requests an administrative warrant from a U.S. District Court Judge or Magistrate.

To secure an administrative warrant, OSHA does not need to show criminal probable cause; showing that the inspection is part of a neutral administrative plan (e.g., SST program) or based on a specific employee complaint satisfies administrative probable cause.

The Three Phases of an OSHA Inspection

An OSHA inspection follows a structured three-phase protocol: +-----------------------+ +-----------------------+ +-----------------------+

  • | Opening Conference | --> | Walkaround Inspection | --> | Closing Conference |
  • +-----------------------+ +-----------------------+ +-----------------------+
  • Phase 1: Opening Conference

The CSHO presents credentials, explains the purpose and scope of the inspection, and provides copies of any employee complaints (redacting complainant identity if requested).

The CSHO identifies trade secret areas under Section 15 to ensure confidentiality protections under 29 CFR 1903.9.

Selection of walkaround representatives: under 29 CFR 1903.8, an authorized employee representative (such as a union representative or employee-designated safety committee member) has the right to accompany the CSHO.

Review of required compliance documents: the CSHO inspects OSHA 300 Logs , OSHA 300A Summaries , OSHA 301 Incident Reports , written hazard communication programs, SDSs, and safety training records.

Phase 2: Walkaround Inspection

The CSHO, accompanied by management and employee walkaround representatives, inspects facility operations, machinery, chemical storage, and work practices.

CSHOs may take photographs, record videos, take environmental air/noise samples, and examine safety devices.

Private Employee Interviews : CSHOs have statutory authority under Section 8(a) to conduct private, confidential interviews with non-supervisory employees out of the presence of management.

CSHOs point out observed hazards immediately; employers are encouraged to abate hazards on the spot when feasible.

Phase 3: Closing Conference

The CSHO conducts a closing meeting with employer and employee representatives to discuss observed safety hazards, potential violations, and apparent compliance issues.

The CSHO details employer rights, informal conference procedures, and contesting options.

The CSHO does not issue citations or calculate dollar penalties during the closing conference; citation decisions and penalty calculations are made subsequently by the OSHA Area Director.

OSHA Inspection Priority Tiers - Illustrative Relative Emphasis (not OSHA-published data)