Study guide

12.5 Membrane Filtration Systems Operation (Subclass 6)

Pennsylvania Water and Wastewater Operator Certification Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Pennsylvania Regulatory Framework & Operator Administration

1.1 Act 11 of 2002 & 25 Pa. Code Chapter 302 Licensing 1.2 Operator Duties, Process Control Decisions & OIRC 1.3 License Renewal, Continuing Education & Facility Security

2 Chapter 2: Essential Water & Wastewater Mathematics

2.1 Volumes, Flow Rates & Detention Time Calculations 2.2 Chemical Feed, Dosage & Dilution Calculations 2.3 Loading Rates & Pumping Hydraulics Calculations

3 Chapter 3: Facility Hydraulics, Mechanical Equipment & Safety

3.1 Centrifugal & Positive Displacement Pumps 3.2 Valves, Piping & Flow Measurement Instrumentation 3.3 Workplace Safety, Confined Spaces & HazCom

4 Chapter 4: Drinking Water Treatment: Clarification & Solids Removal

4.1 Source Water & Rapid Mix Coagulation 4.2 Flocculation & Sedimentation Processes 4.3 Filtration Technologies & Backwashing Protocols

5 Chapter 5: Drinking Water Treatment: Disinfection & Chemical Processes

5.1 Chlorine Disinfection & CT Compliance 5.2 Alternative Disinfection & DBP Control 5.3 Water Softening, Iron/Manganese & Corrosion Control

6 Chapter 6: Drinking Water Distribution & Small Water Systems

6.1 Distribution Infrastructure & Storage Tanks 6.2 Water Quality Maintenance & Cross-Connection Control 6.3 Small Groundwater Systems (Classes Dc & Dn)

7 Chapter 7: Wastewater Treatment: Preliminary & Primary Treatment

7.1 Influent Characterization & Preliminary Screening 7.2 Grit Removal Systems & Velocity Control 7.3 Primary Clarification & Solids Separation

8 Chapter 8: Wastewater Treatment: Secondary Biological Processes

8.1 Activated Sludge Principles & Configurations 8.2 Activated Sludge Troubleshooting & Secondary Clarifiers 8.3 Fixed-Film Technologies & Treatment Ponds

9 Chapter 9: Nutrient Removal, Chesapeake Bay Compliance & Biosolids

9.1 Biological Nitrogen Removal (Nitrification/Denitrification) 9.2 Phosphorus Removal & Chesapeake Bay Compliance 9.3 Sludge Processing, Digestion & Biosolids Management

10 Chapter 10: Wastewater Collection, Laboratory Testing & Regulatory Reporting

10.1 Wastewater Collection Systems & Lift Stations 10.2 Sampling & Laboratory Procedures (QA/QC) 10.3 Regulatory Compliance Reporting (eDMR / DWELR) & Emergency Response

11 Chapter 11: Drinking Water Regulations, Operator Science & Residuals

11.1 Chapter 109, Part 141 Rules & Public Water System Classification 11.2 Water & Wastewater Chemistry Fundamentals 11.3 Microbiology, Pathogens & Waterborne Disease 11.4 Treatment Plant Residuals & Filter Backwash Recycling

12 Chapter 12: Alternative Filtration Technologies (Subclasses 2 through 6)

12.1 Direct Filtration (Subclass 2) 12.2 Diatomaceous Earth Filtration (Subclass 3) 12.3 Slow Sand Filtration (Subclass 4) 12.4 Cartridge & Bag Filtration (Subclass 5) 12.5 Membrane Filtration Systems Operation (Subclass 6)

13 Chapter 13: Chemical Addition & Contaminant Removal (Subclasses 8 through 10)

13.1 Chemical Addition Systems & Feed Equipment (Subclass 8) 13.2 Ion Exchange & Inorganics Removal (Subclass 9) 13.3 Aeration, Air Stripping & Activated Carbon Adsorption (Subclass 10)

14 Chapter 14: Disinfection Technology Subclasses (11 through 14)

14.1 Gaseous Chlorine Feed Systems (Subclass 11) 14.2 Nongaseous Chemical Disinfection Systems (Subclass 12) 14.3 Ultraviolet Disinfection Systems (Subclass 13) 14.4 Ozone Generation & Contacting Systems (Subclass 14)

15 Chapter 15: Plant Support Systems: Electrical, Maintenance & Instrumentation

15.1 Electrical Fundamentals & Motor Control 15.2 Preventive & Corrective Maintenance Programs 15.3 Instrumentation, SCADA & Online Analyzer Calibration

16 Chapter 16: Wastewater Effluent Disinfection, Lagoon Control & Industrial Pretreatment

16.1 Wastewater Effluent Disinfection & Dechlorination 16.2 Lagoon Process Control, Sludge Surveys & Seasonal Discharge 16.3 Industrial Pretreatment Programs

12.5 Membrane Filtration Systems Operation (Subclass 6)

Key Takeaways Explain This Topic AI

DEP defines Subclassification 6 as a pressure or vacuum driven separation process in which particulate matter larger than one micrometer is rejected by an engineered barrier, verifiable by direct integrity testing, and it covers microfiltration, ultrafiltration, nanofiltration and reverse osmosis.

Flux is permeate flow per square foot per day, and specific flux is flux divided by transmembrane pressure: 5 gpm through 75 square feet for 24 hours is 96 gfd, and at 20 psi that is 4.8 gfd/psi.

Transmembrane pressure direction is the diagnosis: a gradual rise is normal, a sudden rise points to feed water or pretreatment, and a sudden drop outside a cleaning points to a failed module or a failed pressure instrument.

Cross flow sweeps the membrane surface and extends run time at slightly higher energy cost while dead end flow sends all feed water through the membrane, but neither reverse flow nor cross flow is as effective as a rapid sand filter backwash, so maintenance cleaning and clean-in-place with acid for scale and caustic or hypochlorite for organic and biological fouling remain unavoidable.

Nanofiltration and reverse osmosis remove dissolved hardness, disinfection byproduct precursors and many regulated contaminants but produce aggressive, low-alkalinity permeate that must be stabilized before distribution.

Last updated: September 2026

Operating the Membrane, Not Just Describing It

Hollow fiber construction and the pressure decay integrity test are introduced with granular filtration in Chapter 4. The Subclass 6 examination goes further: DEP's definition covers microfiltration, ultrafiltration, nanofiltration and reverse osmosis , and the exam asks how an operator runs a membrane plant day to day. Start with the spectrum DEP publishes:

Level Pore size range Target contaminants Typical operating pressure

Microfiltration 0.05 to 1.0 micrometer Particulates, algae, Giardia , Cryptosporidium , bacteria, clays 15 to 40 psi

Ultrafiltration 0.005 to 0.5 micrometer Everything microfiltration removes, plus humic acids and some viruses Moderate

Nanofiltration 0.0005 to 0.01 micrometer Adds dissolved metals and salts Elevated

Reverse osmosis 0.0001 to 0.001 micrometer Adds the smallest dissolved metals and salts Up to 800 to 1,000 psi at the tightest pore sizes

Manufacturers also rate tight membranes by molecular weight cut-off (MWCO) , expressed in daltons, rather than by pore diameter. One process on the Subclass 6 list is not pressure driven at all: electrodialysis uses an electrical force to move ions and their associated water to the membrane instead of pushing the whole solution through it, and is used mainly for desalination and deionization.

Four numbers then drive every operating decision.

Parameter Definition What it tells the operator

Flux Permeate flow per unit membrane area, in gallons per square foot per day (gfd) How hard the membrane is being pushed

Transmembrane pressure (TMP) Pressure difference driving water through the membrane Resistance the membrane is presenting

Specific flux (permeability) Flux divided by TMP, temperature normalized The true health of the membrane

Recovery Permeate volume divided by feed volume, as a percent How much water is being wasted, and how concentrated the reject is

Working the Flux Math

DEP's own worked example is the pattern to memorize. A module holds 75 square feet of membrane area and runs 24 hours at 5 gpm:

  • Volume produced: 5 gpm x 60 min/hr x 24 hr = 7,200 gallons per day
  • Flux: 7,200 gpd / 75 sq ft = 96 gfd
  • Specific flux at a transmembrane pressure of 20 psi: 96 gfd / 20 psi = 4.8 gfd/psi

The lower the specific flux, the more pressure the system is losing and the more expensive it is to run. Cleaning effectiveness is judged with the companion equation Loss of original specific flux = 100 x (1 - Jsi/Jsio) , where Jsi is specific flux measured on restart after a cleaning and Jsio is specific flux at the time-zero baseline. When repeated cleanings can no longer pull that loss back down, the modules are at end of life.

Temperature Normalization: The Most Common Misread

Cold water is more viscous, so TMP rises in winter even on a perfectly clean membrane. An operator who reacts to raw TMP alone will clean membranes that do not need cleaning in January and miss real fouling in July. Manufacturers supply a temperature correction factor that converts observed specific flux to a standard reference temperature, usually 20 degrees C. Normalized specific flux is the trend that matters : a steady decline over weeks indicates genuine fouling, while a seasonal swing that recovers in spring indicates viscosity.

Flow Path and DEP's Operating Vocabulary

Subclass 6 items use DEP's terms, which differ from generic industry wording:

Cross flow allows a small portion of the feed to sweep across the membrane surface instead of through it. It scours the surface, extends the interval between cleanings, and costs slightly more energy because some pumped water never becomes permeate. It is chosen for poorer-quality feed water or where powdered activated carbon is dosed upstream.

Dead end flow sends all feed water through the membrane. Simpler and cheaper to pump, but it accumulates solids faster.

Reverse flow (RF) drives permeate backward through the membrane to lift deposited material, then discards the waste stream. DEP is explicit that RF is not as effective as a rapid sand filter backwash , which is exactly why periodic chemical cleaning is unavoidable.

Back pulse is the same reversal performed as a short, sharp pulse.

Air scrub (AS) injects air on the feed side during RF to agitate the surface and improve solids release; some submerged systems run continuous low-rate air in the process tank.

Concentrate or reject is the waste created by an RF, and rejection is the percentage reduction of a solute in the permeate relative to the feed.

Backwash recovery reclaims RF waste through settling, bag or cartridge filters, or another membrane, and returns the recovered water to the feed side.

A membrane control system automatically runs five procedures: flux maintenance, RF, maintenance chemical cleaning, cross flow maintenance and membrane integrity testing .

Fouling: Diagnosis Before Chemistry

Fouling type Cause Signature Cleaning approach

Particulate/colloidal Silt, clay, coagulant carryover TMP rises quickly, recovers well after backpulse Physical backpulse and air scour

Organic Natural organic matter adsorbing to the surface Gradual permeability loss, poor backpulse recovery Caustic soda, often with hypochlorite

Biological (biofouling) Microbial growth on the surface and in feed channels Slow permeability loss, rising feed channel pressure drop Hypochlorite or an approved biocide, plus source control

Scaling Calcium carbonate, calcium sulfate, silica precipitating at high recovery Permeability loss concentrated in the last stage of an RO array Citric or hydrochloric acid; prevention by antiscalant or lower recovery

The Cleaning Hierarchy

Backpulse or backwash. Permeate is driven backward through the fiber every 15 to 60 minutes, often with air scour, to lift the reversible cake. Typical duration is under a minute.

Maintenance chemical cleaning , also marketed as a chemically enhanced backwash. A dilute chemical, commonly hypochlorite, caustic or acid, is added to the reverse flow daily or weekly to extend the interval between full cleanings.

Clean-in-place (CIP). The rack is isolated and recirculated with heated cleaning solution for one to several hours. Acid first for scale, then caustic or hypochlorite for organics and biology , with a thorough rinse between and after. CIP is scheduled when normalized specific flux falls to a defined trigger, commonly 20 to 30 percent below the clean baseline.

Integrity verification after cleaning. A direct integrity test is performed before returning the rack to service, because cleaning chemistry and pressure cycling can expose a weak fiber.

Reading TMP, and What to Watch Daily

TMP is the single most important operating parameter, and its direction of change is the diagnosis:

  • TMP behavior Interpretation
  • Gradual increase Normal; the system is operating acceptably
  • Sudden rapid increase Feed water quality change or a pretreatment system problem

Sudden decrease not following a CIP Failure of one or more modules, or failure of the pressure monitoring instrument itself

Daily, the operator confirms the system is holding the target flux, reviews the last several days of trend data, watches TMP, and checks feed and permeate turbidity several times per day . Because the control system holds flux using flow meter signals, the displayed values are only as good as those meters, so meter maintenance and calibration are part of process control rather than a separate maintenance chore. Weekly, verify the on-line analytical equipment by comparing its readings against a calibrated bench-top instrument and confirming the sample flow rates in the manufacturer's manual.

Two limits shape design and operation. Pretreatment reduces the fouling load on the membrane, whether as prefiltration, antiscalant, or acid addition; the silt density index (SDI) is the test used to estimate a feed water's fouling potential. Chemical tolerance is the other limit: chlorine, some organic chemicals and solvents destroy certain membrane materials, so if they cannot be removed ahead of the membrane, a different membrane or a different treatment approach is required. Fouling that a cleaning can reverse is reversible ; fouling that cannot be removed is irreversible and eventually forces module replacement. Modules commonly last 10 years or more , with actual life set by feed water quality, flux rate and cleaning effectiveness.

Recovery and Concentrate

Recovery for low-pressure microfiltration and ultrafiltration is typically 90 to 97 percent , with the balance leaving as backwash waste. Reverse osmosis recovery is lower, commonly 65 to 85 percent for brackish water. Raising recovery has a direct penalty: everything rejected is concentrated into a smaller reject volume, so scaling potential rises sharply. Antiscalant dosing, acid addition for carbonate control, and staged array design exist to manage that trade-off.

Concentrate disposal, discussed with residuals in Chapter 11, is a permitting question and often the limiting factor for a membrane project in Pennsylvania.

Nanofiltration and Reverse Osmosis

Where microfiltration and ultrafiltration remove particles and pathogens, nanofiltration and reverse osmosis reject dissolved constituents:

Nanofiltration is used as membrane softening , removing hardness and a large fraction of disinfection byproduct precursors at moderate pressure.

Reverse osmosis removes monovalent ions, nitrate, arsenic, radionuclides and per- and polyfluoroalkyl substances.

Both produce a permeate that is soft, low in alkalinity and aggressive toward metal pipe . Post-treatment stabilization, typically with lime, caustic, soda ash or calcite contactors plus a corrosion inhibitor, is mandatory before the water enters distribution. Blending a controlled fraction of bypassed feed water back into the permeate is the common way to restore alkalinity and reduce treatment cost simultaneously, provided the bypassed stream carries no pathogen risk.