Study guide

13.1 Chemical Addition Systems & Feed Equipment (Subclass 8)

Pennsylvania Water and Wastewater Operator Certification Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Pennsylvania Regulatory Framework & Operator Administration

1.1 Act 11 of 2002 & 25 Pa. Code Chapter 302 Licensing 1.2 Operator Duties, Process Control Decisions & OIRC 1.3 License Renewal, Continuing Education & Facility Security

2 Chapter 2: Essential Water & Wastewater Mathematics

2.1 Volumes, Flow Rates & Detention Time Calculations 2.2 Chemical Feed, Dosage & Dilution Calculations 2.3 Loading Rates & Pumping Hydraulics Calculations

3 Chapter 3: Facility Hydraulics, Mechanical Equipment & Safety

3.1 Centrifugal & Positive Displacement Pumps 3.2 Valves, Piping & Flow Measurement Instrumentation 3.3 Workplace Safety, Confined Spaces & HazCom

4 Chapter 4: Drinking Water Treatment: Clarification & Solids Removal

4.1 Source Water & Rapid Mix Coagulation 4.2 Flocculation & Sedimentation Processes 4.3 Filtration Technologies & Backwashing Protocols

5 Chapter 5: Drinking Water Treatment: Disinfection & Chemical Processes

5.1 Chlorine Disinfection & CT Compliance 5.2 Alternative Disinfection & DBP Control 5.3 Water Softening, Iron/Manganese & Corrosion Control

6 Chapter 6: Drinking Water Distribution & Small Water Systems

6.1 Distribution Infrastructure & Storage Tanks 6.2 Water Quality Maintenance & Cross-Connection Control 6.3 Small Groundwater Systems (Classes Dc & Dn)

7 Chapter 7: Wastewater Treatment: Preliminary & Primary Treatment

7.1 Influent Characterization & Preliminary Screening 7.2 Grit Removal Systems & Velocity Control 7.3 Primary Clarification & Solids Separation

8 Chapter 8: Wastewater Treatment: Secondary Biological Processes

8.1 Activated Sludge Principles & Configurations 8.2 Activated Sludge Troubleshooting & Secondary Clarifiers 8.3 Fixed-Film Technologies & Treatment Ponds

9 Chapter 9: Nutrient Removal, Chesapeake Bay Compliance & Biosolids

9.1 Biological Nitrogen Removal (Nitrification/Denitrification) 9.2 Phosphorus Removal & Chesapeake Bay Compliance 9.3 Sludge Processing, Digestion & Biosolids Management

10 Chapter 10: Wastewater Collection, Laboratory Testing & Regulatory Reporting

10.1 Wastewater Collection Systems & Lift Stations 10.2 Sampling & Laboratory Procedures (QA/QC) 10.3 Regulatory Compliance Reporting (eDMR / DWELR) & Emergency Response

11 Chapter 11: Drinking Water Regulations, Operator Science & Residuals

11.1 Chapter 109, Part 141 Rules & Public Water System Classification 11.2 Water & Wastewater Chemistry Fundamentals 11.3 Microbiology, Pathogens & Waterborne Disease 11.4 Treatment Plant Residuals & Filter Backwash Recycling

12 Chapter 12: Alternative Filtration Technologies (Subclasses 2 through 6)

12.1 Direct Filtration (Subclass 2) 12.2 Diatomaceous Earth Filtration (Subclass 3) 12.3 Slow Sand Filtration (Subclass 4) 12.4 Cartridge & Bag Filtration (Subclass 5) 12.5 Membrane Filtration Systems Operation (Subclass 6)

13 Chapter 13: Chemical Addition & Contaminant Removal (Subclasses 8 through 10)

13.1 Chemical Addition Systems & Feed Equipment (Subclass 8) 13.2 Ion Exchange & Inorganics Removal (Subclass 9) 13.3 Aeration, Air Stripping & Activated Carbon Adsorption (Subclass 10)

14 Chapter 14: Disinfection Technology Subclasses (11 through 14)

14.1 Gaseous Chlorine Feed Systems (Subclass 11) 14.2 Nongaseous Chemical Disinfection Systems (Subclass 12) 14.3 Ultraviolet Disinfection Systems (Subclass 13) 14.4 Ozone Generation & Contacting Systems (Subclass 14)

15 Chapter 15: Plant Support Systems: Electrical, Maintenance & Instrumentation

15.1 Electrical Fundamentals & Motor Control 15.2 Preventive & Corrective Maintenance Programs 15.3 Instrumentation, SCADA & Online Analyzer Calibration

16 Chapter 16: Wastewater Effluent Disinfection, Lagoon Control & Industrial Pretreatment

16.1 Wastewater Effluent Disinfection & Dechlorination 16.2 Lagoon Process Control, Sludge Surveys & Seasonal Discharge 16.3 Industrial Pretreatment Programs

13.1 Chemical Addition Systems & Feed Equipment (Subclass 8)

Key Takeaways Explain This Topic AI

Positive displacement diaphragm metering pumps deliver a fixed volume per stroke and are calibrated by adjusting stroke length and stroke frequency, so output is verified by drawdown against a calibration cylinder rather than assumed from the dial setting.

A day tank holds no more than one day of chemical use, is filled from bulk storage under operator control, and provides the volume reference used for drawdown calibration and for detecting a leak.

Injection points must be located where mixing is immediate and where the chemical will not damage downstream equipment, and each requires a corporation stop or removable quill so the injector can be cleared of scale.

Sodium hypochlorite off-gases and forms scale in feed lines, so hypochlorite systems use degassing pump heads, flooded suction and periodic acid cleaning of the injector.

Acids and hypochlorite must never share containment, since mixing them liberates chlorine gas, and every chemical system requires compatible materials, secondary containment, eyewash and safety shower, and a current safety data sheet.

Last updated: September 2026

What Subclass 8 Actually Tests

Chemical Addition is one of the larger drinking water subclass examinations at 40 questions, and it appears at nearly every plant because almost every treatment technology feeds something. The knowledge statements center on the ability to adjust chemical feed rates, confirm chemical strength, calibrate equipment, prepare chemicals, and interpret safety data sheets . Dosage arithmetic is covered with the mathematics chapter; this section covers the hardware and the practice.

Feed Equipment by Type

Equipment Principle Typical service Control range

Diaphragm metering pump Positive displacement; fixed volume per stroke Hypochlorite, caustic, polymer, fluoride, corrosion inhibitor About 10 to 1 by stroke length, extended by frequency control

Peristaltic (hose) pump Roller squeezes a flexible tube Polymer, hypochlorite, small doses; tolerates off-gassing well Wide, limited by tube life

Progressive cavity pump Rotor turning in a stator Thick polymer, lime slurry Broad, set by speed

Volumetric dry feeder Screw or belt delivers a fixed volume of powder Lime, soda ash, powdered activated carbon Moderate accuracy, roughly plus or minus 2 percent

Gravimetric dry feeder Loss-in-weight control Lime and soda ash where accuracy matters High accuracy, roughly plus or minus 1 percent

Gas chlorinator Vacuum regulator and ejector Chlorine and sulfur dioxide Covered in the gaseous disinfection section

Storage, Day Tanks and Transfer

Bulk storage sizing is a compliance decision as much as an economic one: a plant that runs out of coagulant is out of compliance. Standard practice is 30 days of storage at average use , with the caveat that sodium hypochlorite degrades in storage , losing strength faster when warm, when exposed to light, and when diluted with hard water. Hypochlorite inventory is therefore sized for weeks, not months.

A day tank sits between bulk storage and the metering pump:

Holds no more than one operating day of chemical.

Is filled deliberately by the operator or under interlocked control, never left connected to bulk storage.

Carries a calibrated sight glass or level element, which is what makes drawdown calibration and leak detection possible.

Limits the volume that can be released in a single failure, which is why secondary containment is sized to the largest single container.

Calibrating a Metering Pump by Drawdown

The dial setting on a metering pump is an indication, not a measurement. Feed rate is verified as follows:

Isolate the pump suction from the day tank and place it on a graduated calibration cylinder filled with the same chemical.

Run the pump at the operating setting for a measured time, commonly five minutes.

Record the volume drawn from the cylinder.

Convert to gallons per day and compare against the required feed rate.

Adjust stroke length or frequency and repeat until the delivered rate matches, then record the setting and the verified rate in the log.

Calibration is repeated after any change of chemical lot or strength, after maintenance on the pump head or check valves, and on a routine schedule. A drawdown result that is far below the setting normally indicates worn check valves, a gas bubble in the pump head, or a clogged injector.

Injection Points and Their Failures

Inject where immediate mixing occurs, such as a turbulent zone, a static mixer or the suction side of a pump where permitted for the chemical.

Use a removable quill or corporation stop so the injector can be pulled and cleaned without shutting down the main.

Keep chemicals that react with each other far apart. Feeding hypochlorite and an acid at nearly the same point can generate chlorine gas and will destroy the intended treatment.

Watch for injector scaling : hypochlorite raises local pH and precipitates calcium carbonate at the injection point, gradually restricting flow. The symptom is a rising discharge pressure and a falling delivered dose despite an unchanged pump setting, and the remedy is a scheduled acid soak of the quill.

Off-gassing in hypochlorite lines causes vapor lock. Flooded suction, a degassing pump head, foot valves and correctly sloped tubing all address it.

Chemical Safety Discipline

  • Rule Reason
  • Never store or contain acids with hypochlorite Mixing releases chlorine gas
  • Never store calcium hypochlorite with organics, oils or rags Strong oxidizer; fire and explosion hazard
  • Add acid to water, never water to acid Violent exothermic reaction and spattering

Confirm connections before every bulk delivery Cross-connecting a delivery to the wrong tank has caused fatal gas releases at water plants

Verify material compatibility for tanks, tubing and gaskets Hypochlorite attacks many metals; caustic attacks aluminum; fluorosilicic acid attacks concrete

Maintain eyewash, safety shower, ventilation, spill kit and current safety data sheets Required by the hazard communication and confined space programs described in the safety section

Exam tactic: when a scenario shows a stable pump setting but a declining chlorine residual, look for injector scaling, a failed check valve, off-gassing in the suction line, or hypochlorite that has lost strength in storage before concluding the demand changed.