Study guide

13.2 Ion Exchange & Inorganics Removal (Subclass 9)

Pennsylvania Water and Wastewater Operator Certification Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Pennsylvania Regulatory Framework & Operator Administration

1.1 Act 11 of 2002 & 25 Pa. Code Chapter 302 Licensing 1.2 Operator Duties, Process Control Decisions & OIRC 1.3 License Renewal, Continuing Education & Facility Security

2 Chapter 2: Essential Water & Wastewater Mathematics

2.1 Volumes, Flow Rates & Detention Time Calculations 2.2 Chemical Feed, Dosage & Dilution Calculations 2.3 Loading Rates & Pumping Hydraulics Calculations

3 Chapter 3: Facility Hydraulics, Mechanical Equipment & Safety

3.1 Centrifugal & Positive Displacement Pumps 3.2 Valves, Piping & Flow Measurement Instrumentation 3.3 Workplace Safety, Confined Spaces & HazCom

4 Chapter 4: Drinking Water Treatment: Clarification & Solids Removal

4.1 Source Water & Rapid Mix Coagulation 4.2 Flocculation & Sedimentation Processes 4.3 Filtration Technologies & Backwashing Protocols

5 Chapter 5: Drinking Water Treatment: Disinfection & Chemical Processes

5.1 Chlorine Disinfection & CT Compliance 5.2 Alternative Disinfection & DBP Control 5.3 Water Softening, Iron/Manganese & Corrosion Control

6 Chapter 6: Drinking Water Distribution & Small Water Systems

6.1 Distribution Infrastructure & Storage Tanks 6.2 Water Quality Maintenance & Cross-Connection Control 6.3 Small Groundwater Systems (Classes Dc & Dn)

7 Chapter 7: Wastewater Treatment: Preliminary & Primary Treatment

7.1 Influent Characterization & Preliminary Screening 7.2 Grit Removal Systems & Velocity Control 7.3 Primary Clarification & Solids Separation

8 Chapter 8: Wastewater Treatment: Secondary Biological Processes

8.1 Activated Sludge Principles & Configurations 8.2 Activated Sludge Troubleshooting & Secondary Clarifiers 8.3 Fixed-Film Technologies & Treatment Ponds

9 Chapter 9: Nutrient Removal, Chesapeake Bay Compliance & Biosolids

9.1 Biological Nitrogen Removal (Nitrification/Denitrification) 9.2 Phosphorus Removal & Chesapeake Bay Compliance 9.3 Sludge Processing, Digestion & Biosolids Management

10 Chapter 10: Wastewater Collection, Laboratory Testing & Regulatory Reporting

10.1 Wastewater Collection Systems & Lift Stations 10.2 Sampling & Laboratory Procedures (QA/QC) 10.3 Regulatory Compliance Reporting (eDMR / DWELR) & Emergency Response

11 Chapter 11: Drinking Water Regulations, Operator Science & Residuals

11.1 Chapter 109, Part 141 Rules & Public Water System Classification 11.2 Water & Wastewater Chemistry Fundamentals 11.3 Microbiology, Pathogens & Waterborne Disease 11.4 Treatment Plant Residuals & Filter Backwash Recycling

12 Chapter 12: Alternative Filtration Technologies (Subclasses 2 through 6)

12.1 Direct Filtration (Subclass 2) 12.2 Diatomaceous Earth Filtration (Subclass 3) 12.3 Slow Sand Filtration (Subclass 4) 12.4 Cartridge & Bag Filtration (Subclass 5) 12.5 Membrane Filtration Systems Operation (Subclass 6)

13 Chapter 13: Chemical Addition & Contaminant Removal (Subclasses 8 through 10)

13.1 Chemical Addition Systems & Feed Equipment (Subclass 8) 13.2 Ion Exchange & Inorganics Removal (Subclass 9) 13.3 Aeration, Air Stripping & Activated Carbon Adsorption (Subclass 10)

14 Chapter 14: Disinfection Technology Subclasses (11 through 14)

14.1 Gaseous Chlorine Feed Systems (Subclass 11) 14.2 Nongaseous Chemical Disinfection Systems (Subclass 12) 14.3 Ultraviolet Disinfection Systems (Subclass 13) 14.4 Ozone Generation & Contacting Systems (Subclass 14)

15 Chapter 15: Plant Support Systems: Electrical, Maintenance & Instrumentation

15.1 Electrical Fundamentals & Motor Control 15.2 Preventive & Corrective Maintenance Programs 15.3 Instrumentation, SCADA & Online Analyzer Calibration

16 Chapter 16: Wastewater Effluent Disinfection, Lagoon Control & Industrial Pretreatment

16.1 Wastewater Effluent Disinfection & Dechlorination 16.2 Lagoon Process Control, Sludge Surveys & Seasonal Discharge 16.3 Industrial Pretreatment Programs

13.2 Ion Exchange & Inorganics Removal (Subclass 9)

Key Takeaways Explain This Topic AI

Strong acid cation resin in the sodium form exchanges two sodium ions for each calcium or magnesium ion removed, so softened water gains sodium in proportion to the hardness removed.

Resin exchange capacity is expressed in kilograins of hardness as calcium carbonate per cubic foot, and run length is calculated by dividing total bed capacity by the hardness load per gallon.

A regeneration cycle is backwash, brine draw and slow rinse, then fast rinse and return to service, and shortening the slow rinse is the most common cause of salty finished water.

Nitrate-selective resin is required for nitrate removal because a standard resin releases previously captured nitrate in a concentrated peak when it is exhausted by sulfate, a phenomenon called chromatographic peaking.

Regeneration brine carries very high chloride, sodium, hardness and whatever contaminant was removed, so a disposal route, typically a permitted sanitary sewer discharge, must be secured before the technology is selected.

Last updated: September 2026

Ion Exchange as a Unit Process

Ion exchange passes water through a bed of resin beads that hold loosely bound ions and swap them for ions in the water. The DEP subclassification pairs ion exchange with greensand because both are regenerable media beds operated on a service and regeneration cycle, and both are commonly the only treatment at small Pennsylvania groundwater systems.

Resin type Exchange form Removes Releases

Strong acid cation (SAC), sodium form Sodium Calcium, magnesium, radium, barium, some iron and manganese Sodium

  • Strong acid cation, hydrogen form Hydrogen Cations with acid production Hydrogen ion, lowering pH
  • Strong base anion (SBA), chloride form Chloride Nitrate, sulfate, arsenate, uranium, chromate Chloride
  • Nitrate-selective anion Chloride Nitrate preferentially over sulfate Chloride

Manganese greensand Manganese oxide coating Iron, manganese, hydrogen sulfide by oxidation Regenerated with potassium permanganate

The selectivity order matters. A standard strong base anion resin prefers sulfate over nitrate , which creates the peaking behavior described below.

Capacity and Run Length

Resin capacity is rated in kilograins of hardness as calcium carbonate removed per cubic foot of resin , commonly 20 to 30 kilograins per cubic foot at typical salt doses. The operator-level calculation is:

Grains per gallon of hardness equals hardness in mg/L as calcium carbonate divided by 17.1.

Total capacity in grains equals resin volume in cubic feet times rated capacity in kilograins per cubic foot times 1,000.

Gallons to exhaustion equals total capacity in grains divided by grains per gallon.

Higher salt dosages during regeneration buy more capacity per cubic foot, but with diminishing returns and rising brine strength and volume. Selecting the salt dose is therefore a direct trade between run length and waste load.

The Regeneration Cycle

Backwash. Upflow at a rate that expands the bed, removing accumulated particulates and reclassifying the resin. Skipping backwash lets the bed channel.

Brine draw and slow rinse. Concentrated sodium chloride solution, typically 10 to 26 percent, is drawn slowly through the bed. Contact time is what actually regenerates the resin, so this step is deliberately slow. The slow rinse that follows displaces brine at the same low rate.

Fast rinse. Full-rate service water rinses residual brine to waste until conductivity or chloride falls to the service standard.

Return to service.

The two classic failures are short-cycling the slow rinse , which sends salty water to the distribution system and generates customer complaints and possible sodium concerns, and regenerating on time rather than on volume , which either wastes salt or breaks through on hardness.

Nitrate and Chromatographic Peaking

Nitrate is a health-based MCL at 10 mg/L as nitrogen and is acutely dangerous to infants. On a standard chloride-form anion resin the bed captures both sulfate and nitrate, but because the resin prefers sulfate, continued operation past exhaustion causes sulfate to displace previously captured nitrate , releasing it in a slug at a concentration higher than the raw water . An operator who runs a standard resin past breakthrough can therefore deliver water worse than untreated.

Controls:

Use a nitrate-selective resin , which prefers nitrate over sulfate.

Regenerate on treated volume , monitored against the calculated capacity, not on a clock.

Monitor nitrate at the effluent and blend with a controlled fraction of raw water only where the blend is continuously verified.

Other Inorganic Contaminants

Contaminant Removal approach Operator note

Arsenic (MCL 0.010 mg/L) Strong base anion or, more commonly, adsorptive iron-based media Arsenite must be oxidized to arsenate first; sulfate and competing anions shorten run length

Radium Strong acid cation in sodium form, or lime softening Spent resin and brine can carry regulated radioactivity, which complicates disposal

Uranium Strong base anion Very high resin affinity; disposal of exhausted resin is the constraint

Iron and manganese Manganese greensand with permanganate regeneration, or oxidation and filtration Iron fouls anion and cation resins; pretreat before ion exchange

Resin Fouling and Loss

Iron fouling coats beads and reduces capacity; symptoms are shortened runs and rusty backwash. Treated with an acid or a reducing cleaner.

Organic fouling of anion resin by natural organic matter produces gradual capacity loss and color throw; treated with a warm brine and caustic soak.

Oxidant damage. Free chlorine attacks resin structure, so chlorinated water must not be applied to a resin bed unless the resin is rated for it. Dechlorinate ahead of the vessel.

Physical loss. Excessive backwash rate carries beads out the top; a broken underdrain lets them out the bottom, and the giveaway is resin appearing in the distribution system or in a downstream strainer.

The Brine Problem

Every regeneration produces a short, high-strength waste containing the salt used plus everything removed. Typical volumes are 2 to 5 percent of the water treated but the strength is extreme. Discharge options are a permitted sanitary sewer discharge , which may be limited by the receiving wastewater plant's ability to tolerate chloride and by its own permit limits, or a surface water NPDES discharge , which is difficult to obtain for total dissolved solids. Where radium or uranium is involved, the waste may be subject to radioactive material handling requirements. Securing the disposal route is part of selecting the technology, not an afterthought.