Study guide
11.2 Water & Wastewater Chemistry Fundamentals
Pennsylvania Water and Wastewater Operator Certification Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Pennsylvania Regulatory Framework & Operator Administration
1.1 Act 11 of 2002 & 25 Pa. Code Chapter 302 Licensing 1.2 Operator Duties, Process Control Decisions & OIRC 1.3 License Renewal, Continuing Education & Facility Security
2 Chapter 2: Essential Water & Wastewater Mathematics
2.1 Volumes, Flow Rates & Detention Time Calculations 2.2 Chemical Feed, Dosage & Dilution Calculations 2.3 Loading Rates & Pumping Hydraulics Calculations
3 Chapter 3: Facility Hydraulics, Mechanical Equipment & Safety
3.1 Centrifugal & Positive Displacement Pumps 3.2 Valves, Piping & Flow Measurement Instrumentation 3.3 Workplace Safety, Confined Spaces & HazCom
4 Chapter 4: Drinking Water Treatment: Clarification & Solids Removal
4.1 Source Water & Rapid Mix Coagulation 4.2 Flocculation & Sedimentation Processes 4.3 Filtration Technologies & Backwashing Protocols
5 Chapter 5: Drinking Water Treatment: Disinfection & Chemical Processes
5.1 Chlorine Disinfection & CT Compliance 5.2 Alternative Disinfection & DBP Control 5.3 Water Softening, Iron/Manganese & Corrosion Control
6 Chapter 6: Drinking Water Distribution & Small Water Systems
6.1 Distribution Infrastructure & Storage Tanks 6.2 Water Quality Maintenance & Cross-Connection Control 6.3 Small Groundwater Systems (Classes Dc & Dn)
7 Chapter 7: Wastewater Treatment: Preliminary & Primary Treatment
7.1 Influent Characterization & Preliminary Screening 7.2 Grit Removal Systems & Velocity Control 7.3 Primary Clarification & Solids Separation
8 Chapter 8: Wastewater Treatment: Secondary Biological Processes
8.1 Activated Sludge Principles & Configurations 8.2 Activated Sludge Troubleshooting & Secondary Clarifiers 8.3 Fixed-Film Technologies & Treatment Ponds
9 Chapter 9: Nutrient Removal, Chesapeake Bay Compliance & Biosolids
9.1 Biological Nitrogen Removal (Nitrification/Denitrification) 9.2 Phosphorus Removal & Chesapeake Bay Compliance 9.3 Sludge Processing, Digestion & Biosolids Management
10 Chapter 10: Wastewater Collection, Laboratory Testing & Regulatory Reporting
10.1 Wastewater Collection Systems & Lift Stations 10.2 Sampling & Laboratory Procedures (QA/QC) 10.3 Regulatory Compliance Reporting (eDMR / DWELR) & Emergency Response
11 Chapter 11: Drinking Water Regulations, Operator Science & Residuals
11.1 Chapter 109, Part 141 Rules & Public Water System Classification 11.2 Water & Wastewater Chemistry Fundamentals 11.3 Microbiology, Pathogens & Waterborne Disease 11.4 Treatment Plant Residuals & Filter Backwash Recycling
12 Chapter 12: Alternative Filtration Technologies (Subclasses 2 through 6)
12.1 Direct Filtration (Subclass 2) 12.2 Diatomaceous Earth Filtration (Subclass 3) 12.3 Slow Sand Filtration (Subclass 4) 12.4 Cartridge & Bag Filtration (Subclass 5) 12.5 Membrane Filtration Systems Operation (Subclass 6)
13 Chapter 13: Chemical Addition & Contaminant Removal (Subclasses 8 through 10)
13.1 Chemical Addition Systems & Feed Equipment (Subclass 8) 13.2 Ion Exchange & Inorganics Removal (Subclass 9) 13.3 Aeration, Air Stripping & Activated Carbon Adsorption (Subclass 10)
14 Chapter 14: Disinfection Technology Subclasses (11 through 14)
14.1 Gaseous Chlorine Feed Systems (Subclass 11) 14.2 Nongaseous Chemical Disinfection Systems (Subclass 12) 14.3 Ultraviolet Disinfection Systems (Subclass 13) 14.4 Ozone Generation & Contacting Systems (Subclass 14)
15 Chapter 15: Plant Support Systems: Electrical, Maintenance & Instrumentation
15.1 Electrical Fundamentals & Motor Control 15.2 Preventive & Corrective Maintenance Programs 15.3 Instrumentation, SCADA & Online Analyzer Calibration
16 Chapter 16: Wastewater Effluent Disinfection, Lagoon Control & Industrial Pretreatment
16.1 Wastewater Effluent Disinfection & Dechlorination 16.2 Lagoon Process Control, Sludge Surveys & Seasonal Discharge 16.3 Industrial Pretreatment Programs
11.2 Water & Wastewater Chemistry Fundamentals
Key Takeaways Explain This Topic AI
pH is a logarithmic measure of hydrogen ion activity, so a drop from pH 7.0 to pH 5.0 is a hundredfold increase in hydrogen ion concentration, not a doubling.
Alkalinity exists as bicarbonate, carbonate and hydroxide, and it is the buffer consumed when alum or ferric coagulant is fed; roughly 0.5 mg/L of alkalinity as calcium carbonate is destroyed per mg/L of alum applied.
Hardness and alkalinity are both reported as mg/L as calcium carbonate so that unlike ions can be added and compared on one basis.
Dissolved oxygen saturation falls as temperature rises, which is why an aeration basin needs more air in August than in February to hold the same residual.
Pounds per day equals dose in mg/L times flow in MGD times 8.34, and one grain per gallon of hardness equals 17.1 mg/L as calcium carbonate.
Last updated: September 2026
The Chemistry an Operator Is Actually Tested On
Pennsylvania does not test operators as chemists. It tests whether an operator can predict what a chemical will do to a process and recognize when a laboratory result is impossible. Six concepts carry nearly all of the chemistry questions.
1. pH, Acids and Bases
pH measures hydrogen ion activity on a logarithmic scale from 0 to 14, with 7.0 neutral at standard temperature. Because the scale is logarithmic, each whole unit is a tenfold change:
pH 6.0 water is ten times more acidic than pH 7.0 water.
pH 5.0 water is one hundred times more acidic than pH 7.0 water.
This is why a small pH excursion matters so much. Coagulation with aluminum sulfate works best between about pH 5.5 and 7.5 ; hypochlorous acid, the effective form of free chlorine, dominates below about pH 7.5 and gives way to the far weaker hypochlorite ion above it; and nitrifying bacteria in an aeration basin stall below about pH 6.5 .
2. Alkalinity: The Buffer That Gets Consumed
Alkalinity is the water's capacity to neutralize acid. It is measured by titration and reported as mg/L as calcium carbonate . Three forms exist, and which one is present depends on pH:
- Form Present when Behavior
- Bicarbonate (HCO3-) pH roughly 4.5 to 8.3 The dominant natural form in Pennsylvania surface and ground water
- Carbonate (CO3 2-) pH above about 8.3 Appears during lime softening and high-pH treatment
- Hydroxide (OH-) pH above about 9.4 Produced by caustic soda or excess lime
Coagulants are acids in solution. Feeding alum destroys roughly 0.5 mg/L of alkalinity for every 1 mg/L of alum applied , and ferric chloride destroys somewhat more. A low-alkalinity raw water will therefore lose pH control as coagulant is increased, which is the standard reason a plant supplements with lime, soda ash or caustic soda.
3. Hardness and the Calcium Carbonate Basis
Hardness is the sum of divalent cations, dominated by calcium and magnesium. Both hardness and alkalinity are converted to mg/L as CaCO3 so that they share a common basis and can be subtracted:
Carbonate hardness (temporary hardness) is the portion of hardness matched by alkalinity; it precipitates when heated or when lime is added.
Noncarbonate hardness (permanent hardness) is hardness in excess of alkalinity and is associated with sulfate and chloride; removing it requires soda ash in lime softening or an ion exchange resin.
Water below about 75 mg/L as CaCO3 is soft, 75 to 150 is moderately hard, and above 300 is very hard.
4. Oxidation and Reduction
An oxidizing agent gains electrons and is itself reduced. Chlorine, chlorine dioxide, permanganate and ozone are the oxidants operators feed. They convert soluble reduced species into insoluble oxidized species that a filter can capture:
Ferrous iron (Fe2+, soluble and colorless) oxidizes to ferric iron (Fe3+, red-brown, filterable).
Manganous manganese (Mn2+, soluble) oxidizes to manganese dioxide (black, filterable).
Sulfide oxidizes to sulfate, removing rotten-egg odor.
Reducing agents run the reaction backwards. Sodium bisulfite, sodium metabisulfite and sulfur dioxide are fed to dechlorinate a wastewater effluent, and ascorbic acid is used to neutralize chlorine in a sample bottle.
5. Solution Strength, Specific Gravity and Equivalent Weight
Chemicals are purchased as solutions and solids of stated strength, and the pump must move product, not pure chemical:
Product Typical strength Note
Sodium hypochlorite 10 to 15 percent trade available chlorine Degrades in storage, faster when warm or exposed to light
- Calcium hypochlorite 65 to 70 percent available chlorine Dry solid; keep away from organics and moisture
- Aluminum sulfate (liquid) 48.5 percent, specific gravity about 1.33 One gallon weighs about 11.1 pounds
- Sodium hydroxide 25 or 50 percent The 50 percent solution crystallizes below about 55 degrees F
Specific gravity is the ratio of a liquid's density to water. Multiply 8.34 pounds per gallon by the specific gravity to get the weight of a gallon of product. DEP's modules note the field tool for this: a hydrometer tests liquid chemical strength by measuring specific gravity, which is how an operator verifies that a delivery matches the purchase specification before it is pumped into a day tank.
Two conversions round out the arithmetic:
Pounds per day = dose in mg/L x flow in MGD x 8.34. A 2.5 MGD plant dosing 32 mg/L of alum feeds 32 x 2.5 x 8.34 = 667 pounds per day of dry alum equivalent. If the alum is a 48.5 percent liquid weighing 11.1 pounds per gallon, that is 667 / (11.1 x 0.485) = about 124 gallons per day of product.
Grains per gallon. Hardness is still reported to customers in grains per gallon in Pennsylvania. One grain per gallon equals 17.1 mg/L as calcium carbonate , so 171 mg/L hardness is 10 grains per gallon.
Finally, know which chemicals move pH in which direction. The chemicals fed to raise pH are sodium hydroxide, calcium hydroxide (hydrated lime), sodium carbonate (soda ash) and potassium hydroxide; the chemicals that lower pH are carbon dioxide, sulfuric acid and the acidic coagulants themselves.
6. Temperature and Gas Solubility
Gas solubility falls as temperature rises. Dissolved oxygen saturation in clean fresh water is roughly 14.6 mg/L at 32 degrees F , about 9.1 mg/L at 68 degrees F , and about 7.6 mg/L at 86 degrees F . Three operating consequences follow: an aeration basin needs more blower output in summer to hold 2.0 mg/L, cold water increases viscosity and therefore backwash drag, and cold water slows every biological and chemical reaction, including chlorine disinfection, which is why CT tables demand more contact time at low temperature.