Study guide

4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow

PE Chemical Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the PE Chemical Exam How to Use This Guide and the NCEES Handbook

2 Chapter 1: Material Balances & Flowsheet Calculations

1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations

3 Chapter 2: Energy Balances & Thermochemistry

2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances

4 Chapter 3: Fluid Statics & Incompressible Pipe Flow

3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations

5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow

4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up

6 Chapter 5: Thermodynamic Laws & Fundamental Relations

5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations

7 Chapter 6: Real Gases & Equations of State

6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions

8 Chapter 7: Phase & Chemical Reaction Equilibria

7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation

9 Chapter 8: Heat Transfer Mechanisms & Conduction

8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange

10 Chapter 9: Heat Exchanger Design & Phase Change

9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances

11 Chapter 10: Mass Transfer Fundamentals & Diffusion

10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)

12 Chapter 11: Distillation Operations

11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components

13 Chapter 12: Rate-Controlled & Equilibrium Separations

12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations

14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors

13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations

15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis

14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models

16 Chapter 15: Physical & Transport Properties of Fluids

15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles

17 Chapter 16: Materials of Construction & Corrosion

16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention

18 Chapter 17: Process Safety & Pressure Relief Systems

17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment

19 Chapter 18: Process Control & Engineering Economics

18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems

20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance

19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation

21 Chapter 20: Plant Operation, Reliability & Continuous Improvement

20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting

4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow

Key Takeaways Explain This Topic AI

A flowing gas must be treated as compressible whenever the local Mach number exceeds 0.30 (Ma > 0.30) or the fractional pressure drop across a conduit or restriction exceeds 10% (Delta P / P_1 > 0.10).

The speed of sound in an ideal gas is c = sqrt(k * R * T / M); it is purely a function of absolute temperature and thermodynamic properties, and is strictly independent of static pressure.

The critical pressure ratio P*/P_0 = [2 / (k + 1)]^(k / (k - 1)) governs sonic choking; for air and diatomic gases (k = 1.40), P*/P_0 = 0.528, whereas for steam and methane (k = 1.30-1.31), P*/P_0 = 0.544-0.546.

When downstream backpressure drops below the critical pressure (P_b <= P*), flow at the restriction throat chokes at Mach 1.0; further reductions in downstream pressure cannot increase mass flow rate or throat velocity.

Under choked conditions, the mass discharge rate is directly proportional to upstream stagnation pressure P_0 and inversely proportional to the square root of absolute stagnation temperature (m_dot proportional to P_0 / sqrt(T_0)).

Last updated: September 2026

4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow

In chemical manufacturing plants, gases frequently flow under conditions involving large pressure gradients, extreme velocities, or rapid depressurization. Examples include emergency relief valves (PRVs), flare headers, restriction orifices, gas pipeline ruptures, high-pressure steam turbines, and vacuum ejectors. When density changes across a piping element become significant, the constant-density assumptions of incompressible fluid mechanics fail completely. Mastering compressible gas dynamics is vital for the NCEES PE Chemical exam, where questions routinely evaluate sonic speed, choking thresholds, relief valve capacities, and stagnation conditions.

1. Fundamentals of Compressible Flow and Compressibility Criteria

A fluid flow is classified as compressible when variations in fluid density ρ \rho ρ significantly influence the momentum and energy balances throughout the flow field. For gases, density is coupled to local static pressure P P P and absolute temperature T T T via the thermodynamic equation of state: ρ = P M Z R T \rho = \frac{P M}{Z R T} ρ = ZRT PM ​

where M M M is molecular weight, R = 8 , 314.5 J/(kmol ⋅ K) = 10.731 psia ⋅ ft 3 / ( lbmol ⋅ ∘ R ) R = 8,314.5\text{ J/(kmol}\cdot\text{K)} = 10.731\text{ psia}\cdot\text{ft}^3/(\text{lbmol}\cdot^\circ\text{R}) R = 8 , 314.5 J/(kmol ⋅ K) = 10.731 psia ⋅ ft 3 / ( lbmol ⋅ ∘ R ) is the universal gas constant, and Z Z Z is the compressibility factor.

The Engineering Threshold for Incompressible vs. Compressible Modeling

Two practical diagnostic criteria dictate when compressible flow equations must be deployed on the PE exam:

The Mach Number Criterion: If the fluid velocity v v v exceeds 30 % 30\% 30% of the local speed of sound ( M a = v / c > 0.30 Ma = v/c > 0.30 M a = v / c > 0.30 ), inertial compression effects cause density changes exceeding 5 % 5\% 5% . Below M a = 0.30 Ma = 0.30 M a = 0.30 , gases can be modeled as incompressible fluids with less than 1 % 1\% 1% error.

The Fractional Pressure Drop Criterion: For flow through a pipeline, valve, or restriction, if the overall pressure drop exceeds 10 % 10\% 10% of the absolute upstream pressure: Δ P P 1 = P 1 − P 2 P 1 > 0.10 \frac{\Delta P}{P_1} = \frac{P_1 - P_2}{P_1} > 0.10 P 1 ​ Δ P ​ = P 1 ​ P 1 ​ − P 2 ​ ​ > 0.10 the fluid density variation is too large for standard incompressible Darcy-Weisbach formulations. If Δ P / P 1 ≤ 0.10 \Delta P / P_1 \le 0.10 Δ P / P 1 ​ ≤ 0.10 , an engineer may use incompressible formulas evaluated at the arithmetic mean density ρ a v g = ( ρ 1 + ρ 2 ) / 2 \rho_{avg} = (\rho_1 + \rho_2)/2 ρ a vg ​ = ( ρ 1 ​ + ρ 2 ​ ) /2 .

2. Speed of Sound (Sonic Velocity) and the Mach Number

The speed of sound ( c c c ) is the velocity at which an infinitesimal acoustic pressure wave propagates through a fluid medium. Because acoustic wave propagation occurs with negligible heat transfer and minimal viscous dissipation, the disturbance travels as an isentropic process (reversible and adiabatic): c = ( ∂ P ∂ ρ ) s c = \sqrt{\left(\frac{\partial P}{\partial \rho}\right)_s} c = ( ∂ ρ ∂ P ​ ) s ​ ​

For an ideal gas obeying the isentropic relation P ρ − k = constant P \rho^{-k} = \text{constant} P ρ − k = constant (where k = C p / C v k = C_p / C_v k = C p ​ / C v ​ is the heat capacity ratio / isentropic expansion exponent): ( ∂ P ∂ ρ ) s = k P ρ = k R T M \left(\frac{\partial P}{\partial \rho}\right)_s = \frac{k P}{\rho} = \frac{k R T}{M} ( ∂ ρ ∂ P ​ ) s ​ = ρ k P ​ = M k RT ​

Yielding the fundamental sonic velocity formula : c = k R T M = k R s p T c = \sqrt{\frac{k R T}{M}} = \sqrt{k R_{sp} T} c = M k RT ​ ​ = k R s p ​ T ​

where R s p = R / M R_{sp} = R / M R s p ​ = R / M is the specific gas constant (in J/(kg ⋅ K) \text{J/(kg}\cdot\text{K)} J/(kg ⋅ K) or ft ⋅ lb f / ( lb m ⋅ ∘ R ) \text{ft}\cdot\text{lb}_f/(\text{lb}_m\cdot^\circ\text{R}) ft ⋅ lb f ​ / ( lb m ​ ⋅ ∘ R ) ).

In US Customary units, apply the gravitational conversion constant g c = 32.174 lb m ⋅ ft / ( lb f ⋅ s 2 ) g_c = 32.174\text{ lb}_m\cdot\text{ft}/(\text{lb}_f\cdot\text{s}^2) g c ​ = 32.174 lb m ​ ⋅ ft / ( lb f ​ ⋅ s 2 ) : c = k g c R T M = k g c R s p T c = \sqrt{\frac{k g_c R T}{M}} = \sqrt{k g_c R_{sp} T} c = M k g c ​ RT ​ ​ = k g c ​ R s p ​ T ​

Important

Sonic Velocity Depends Solely on Temperature! Static pressure does NOT appear in the sonic velocity formula. For an ideal gas, doubling the pressure at constant temperature doubles the density but leaves the speed of sound completely unchanged!

Flow Classification by Mach Number

The Mach number ( M a Ma M a ) is the dimensionless ratio of bulk flow velocity v v v to the local acoustic velocity c c c : M a = v c Ma = \frac{v}{c} M a = c v ​

Subsonic Flow ( M a < 1.0 Ma < 1.0 M a < 1.0 ): Pressure disturbances travel faster than the fluid stream. Upstream fluid elements sense downstream flow restrictions (such as valves or bends) and adjust smoothly prior to arrival.

Sonic Flow ( M a = 1.0 Ma = 1.0 M a = 1.0 ): Fluid velocity exactly matches the speed of sound. Small pressure disturbances cannot propagate upstream against the flow.

Supersonic Flow ( M a > 1.0 Ma > 1.0 M a > 1.0 ): Fluid velocity exceeds the speed of sound. Upstream fluid cannot receive acoustic warning of downstream obstacles, leading to shock waves.

3. Stagnation State and Isentropic Flow Relations

The stagnation state (denoted by subscript 0 0 0 ) is the thermodynamic state a fluid would achieve if brought to rest reversibly and adiabatically ( v → 0 v \to 0 v → 0 ). For a flowing ideal gas with constant specific heats, the energy balance equates enthalpy and kinetic energy: h 0 = h + v 2 2 ⟹ C p T 0 = C p T + v 2 2 h_0 = h + \frac{v^2}{2} \implies C_p T_0 = C_p T + \frac{v^2}{2} h 0 ​ = h + 2 v 2 ​ ⟹ C p ​ T 0 ​ = C p ​ T + 2 v 2 ​

Dividing by C p T C_p T C p ​ T and substituting C p = k R M ( k − 1 ) C_p = \frac{k R}{M (k - 1)} C p ​ = M ( k − 1 ) k R ​ and c 2 = k R T M c^2 = \frac{k R T}{M} c 2 = M k RT ​ yields the stagnation temperature ratio : T 0 T = 1 + ( k − 1 2 ) M a 2 \frac{T_0}{T} = 1 + \left(\frac{k - 1}{2}\right) Ma^2 T T 0 ​ ​ = 1 + ( 2 k − 1 ​ ) M a 2

For an isentropic expansion, combining the temperature ratio with the polytropic isentropic path P / T k k − 1 = constant P / T^{\frac{k}{k-1}} = \text{constant} P / T k − 1 k ​ = constant yields the stagnation pressure ratio and stagnation density ratio : P 0 P = [ 1 + ( k − 1 2 ) M a 2 ] k k − 1 \frac{P_0}{P} = \left[1 + \left(\frac{k - 1}{2}\right) Ma^2\right]^{\frac{k}{k-1}} P P 0 ​ ​ = [ 1 + ( 2 k − 1 ​ ) M a 2 ] k − 1 k ​ ρ 0 ρ = [ 1 + ( k − 1 2 ) M a 2 ] 1 k − 1 \frac{\rho_0}{\rho} = \left[1 + \left(\frac{k - 1}{2}\right) Ma^2\right]^{\frac{1}{k-1}} ρ ρ 0 ​ ​ = [ 1 + ( 2 k − 1 ​ ) M a 2 ] k − 1 1 ​

4. One-Dimensional Variable-Area Duct Dynamics

Combining the differential continuity equation ( d ρ / ρ + d A / A + d v / v = 0 d\rho/\rho + dA/A + dv/v = 0 d ρ / ρ + d A / A + d v / v = 0 ), differential Euler momentum equation ( d P = − ρ v d v dP = -\rho v dv d P = − ρ v d v ), and sonic definition ( c 2 = d P / d ρ c^2 = dP/d\rho c 2 = d P / d ρ ) yields the area-velocity relationship (Hugoniot equation): d A A = ( M a 2 − 1 ) d v v \frac{dA}{A} = (Ma^2 - 1) \frac{dv}{v} A d A ​ = ( M a 2 − 1 ) v d v ​

This fundamental equation reveals why compressible gas flow behaves counter-intuitively compared to liquid flow:

Subsonic Regime ( M a < 1.0 Ma < 1.0 M a < 1.0 ): Since M a 2 − 1 < 0 Ma^2 - 1 < 0 M a 2 − 1 < 0 , a decrease in area ( d A < 0 dA < 0 d A < 0 ) causes an increase in velocity ( d v > 0 dv > 0 d v > 0 ). Fluid accelerates through a converging nozzle, exactly like an incompressible liquid.

Supersonic Regime ( M a > 1.0 Ma > 1.0 M a > 1.0 ): Since M a 2 − 1 > 0 Ma^2 - 1 > 0 M a 2 − 1 > 0 , an increase in area ( d A > 0 dA > 0 d A > 0 ) causes an increase in velocity ( d v > 0 dv > 0 d v > 0 ). Fluid accelerates through a diverging duct.

Sonic Condition ( M a = 1.0 Ma = 1.0 M a = 1.0 ): At M a = 1 Ma = 1 M a = 1 , d A / A = 0 dA/A = 0 d A / A = 0 , meaning sonic velocity can only occur at a local minimum cross-sectional area—the throat ( d A = 0 dA = 0 d A = 0 ).

Warning

Converging Nozzles Cannot Produce Supersonic Flow! A converging nozzle alone can never accelerate a gas beyond M a = 1.0 Ma = 1.0 M a = 1.0 . Regardless of how low the downstream backpressure is set, the maximum exit velocity is sonic. Achieving supersonic expansion requires a converging-diverging (de Laval) nozzle geometry.

5. Choked Flow and the Critical Pressure Ratio

When a gas expands from a high-pressure reservoir ( P 0 , T 0 P_0, T_0 P 0 ​ , T 0 ​ ) through an orifice, nozzle, control valve, or relief valve into a downstream region of lower pressure ( P b P_b P b ​ ), the flow rate increases as backpressure P b P_b P b ​ is reduced. However, once the throat velocity reaches the local speed of sound ( M a t = 1.0 Ma_t = 1.0 M a t ​ = 1.0 ), the system reaches choked flow (or critical flow ).

Evaluating the stagnation pressure formula at the sonic throat condition ( M a = 1.0 Ma = 1.0 M a = 1.0 ) yields the critical pressure ratio ( r c = P ∗ / P 0 r_c = P^* / P_0 r c ​ = P ∗ / P 0 ​ ): P ∗ P 0 = ( 2 k + 1 ) k k − 1 \frac{P^*}{P_0} = \left(\frac{2}{k + 1}\right)^{\frac{k}{k - 1}} P 0 ​ P ∗ ​ = ( k + 1 2 ​ ) k − 1 k ​

where P ∗ P^* P ∗ is the critical throat pressure (the static pressure at the throat when M a = 1 Ma = 1 M a = 1 ).

Typical Values of the Critical Pressure Ratio

Diatomic gases and air ( k = 1.40 k = 1.40 k = 1.40 ): P ∗ P 0 = ( 2 1.4 + 1 ) 1.4 0.4 = ( 0.8333 ) 3.5 = 0.52828 ≈ 0.528 \frac{P^*}{P_0} = \left(\frac{2}{1.4 + 1}\right)^{\frac{1.4}{0.4}} = (0.8333)^{3.5} = 0.52828 \approx 0.528 P 0 ​ P ∗ ​ = ( 1.4 + 1 2 ​ ) 0.4 1.4 ​ = ( 0.8333 ) 3.5 = 0.52828 ≈ 0.528

Triatomic gases, methane, and steam ( k = 1.30 k = 1.30 k = 1.30 to 1.31 1.31 1.31 ): P ∗ P 0 = ( 2 1.31 + 1 ) 1.31 0.31 = ( 0.8658 ) 4.226 = 0.5439 ≈ 0.544 \frac{P^*}{P_0} = \left(\frac{2}{1.31 + 1}\right)^{\frac{1.31}{0.31}} = (0.8658)^{4.226} = 0.5439 \approx 0.544 P 0 ​ P ∗ ​ = ( 1.31 + 1 2 ​ ) 0.31 1.31 ​ = ( 0.8658 ) 4.226 = 0.5439 ≈ 0.544

Monatomic gases ( k = 1.667 k = 1.667 k = 1.667 ): P ∗ P 0 = ( 2 1.667 + 1 ) 1.667 0.667 = ( 0.750 ) 2.5 = 0.4871 ≈ 0.487 \frac{P^*}{P_0} = \left(\frac{2}{1.667 + 1}\right)^{\frac{1.667}{0.667}} = (0.750)^{2.5} = 0.4871 \approx 0.487 P 0 ​ P ∗ ​ = ( 1.667 + 1 2 ​ ) 0.667 1.667 ​ = ( 0.750 ) 2.5 = 0.4871 ≈ 0.487

The Choking Criterion

Unchoked (Subcritical) Flow ( P b / P 0 > P ∗ / P 0 P_b / P_0 > P^* / P_0 P b ​ / P 0 ​ > P ∗ / P 0 ​ ): Throat pressure equals the receiver backpressure ( P t = P b P_t = P_b P t ​ = P b ​ ). The throat Mach number is subsonic ( M a t < 1 Ma_t < 1 M a t ​ < 1 ), and mass flow rate depends on both P 0 P_0 P 0 ​ and P b P_b P b ​ .

Choked (Critical) Flow ( P b / P 0 ≤ P ∗ / P 0 P_b / P_0 \le P^* / P_0 P b ​ / P 0 ​ ≤ P ∗ / P 0 ​ ): Throat pressure is locked at the critical pressure ( P t = P ∗ P_t = P^* P t ​ = P ∗ ). The throat Mach number is identically 1.0 1.0 1.0 . Acoustic pressure disturbances in the receiver propagate at speed c c c , which cannot travel upstream against the sonic throat velocity. Consequently, lowering the downstream backpressure further has zero effect on the throat pressure, velocity, or mass flow rate .

6. Choked Mass Flow Rate Formulations and Relief Sizing

For an ideal gas undergoing isentropic choked flow through a restriction of throat area A t A_t A t ​ with discharge coefficient C d C_d C d ​ , the maximum mass flow rate is governed by: m ˙ c h o k e d = C d A t ρ ∗ c ∗ \dot{m}_{choked} = C_d A_t \rho^* c^* m ˙ c h o k e d ​ = C d ​ A t ​ ρ ∗ c ∗

Substituting the critical density ρ ∗ = ρ 0 ( 2 k + 1 ) 1 k − 1 \rho^* = \rho_0 \left(\frac{2}{k+1}\right)^{\frac{1}{k-1}} ρ ∗ = ρ 0 ​ ( k + 1 2 ​ ) k − 1 1 ​ and critical sonic velocity c ∗ = k R T 0 M ( 2 k + 1 ) c^* = \sqrt{\frac{k R T_0}{M} \left(\frac{2}{k+1}\right)} c ∗ = M k R T 0 ​ ​ ( k + 1 2 ​ ) ​ leads to the classic choked mass flow equation : m ˙ c h o k e d = C d A t P 0 k M R T 0 ( 2 k + 1 ) k + 1 2 ( k − 1 ) \dot{m}_{choked} = C_d A_t P_0 \sqrt{\frac{k M}{R T_0}} \left(\frac{2}{k + 1}\right)^{\frac{k + 1}{2(k - 1)}} m ˙ c h o k e d ​ = C d ​ A t ​ P 0 ​ R T 0 ​ k M ​ ​ ( k + 1 2 ​ ) 2 ( k − 1 ) k + 1 ​

In US Customary units ( P 0 P_0 P 0 ​ in lb f / ft 2 \text{lb}_f/\text{ft}^2 lb f ​ / ft 2 , A t A_t A t ​ in ft 2 \text{ft}^2 ft 2 , T 0 T_0 T 0 ​ in ∘ R ^\circ\text{R} ∘ R , g c = 32.174 g_c = 32.174 g c ​ = 32.174 , R = 1 , 545.3 ft ⋅ lb f / ( lbmol ⋅ ∘ R ) R = 1,545.3\text{ ft}\cdot\text{lb}_f/(\text{lbmol}\cdot^\circ\text{R}) R = 1 , 545.3 ft ⋅ lb f ​ / ( lbmol ⋅ ∘ R ) ): m ˙ c h o k e d = C d A t P 0 k M g c R T 0 ( 2 k + 1 ) k + 1 2 ( k − 1 ) \dot{m}_{choked} = C_d A_t P_0 \sqrt{\frac{k M g_c}{R T_0}} \left(\frac{2}{k + 1}\right)^{\frac{k + 1}{2(k - 1)}} m ˙ c h o k e d ​ = C d ​ A t ​ P 0 ​ R T 0 ​ k M g c ​ ​ ​ ( k + 1 2 ​ ) 2 ( k − 1 ) k + 1 ​

API Standard 520 Formulation for Safety Relief Valves (PRVs)

In the chemical process industries and on the NCEES PE Chemical exam, vapor relief valve sizing adheres to API 520 Part I. For critical vapor flow, the required effective discharge area A A A is expressed as: W = C K d P 1 A K w K c M T Z W = C K_d P_1 A K_w K_c \sqrt{\frac{M}{T Z}} W = C K d ​ P 1 ​ A K w ​ K c ​ TZ M ​ ​

where:

W W W is mass flow rate ( lb/h \text{lb/h} lb/h ),

C C C is the gas expansion coefficient: C = 520 k ( 2 k + 1 ) k + 1 k − 1 C = 520 \sqrt{k \left(\frac{2}{k+1}\right)^{\frac{k+1}{k-1}}} C = 520 k ( k + 1 2 ​ ) k − 1 k + 1 ​ ​ ,

K d K_d K d ​ is the effective discharge coefficient (typically 0.975 0.975 0.975 for certified gas nozzles),

P 1 P_1 P 1 ​ is upstream relieving pressure in absolute units ( psia \text{psia} psia ), equal to set pressure plus allowable overpressure plus atmospheric pressure,

K w K_w K w ​ is the backpressure correction factor ( K w = 1.0 K_w = 1.0 K w ​ = 1.0 for conventional PRVs discharging to atmospheric or balanced bellows valves with backpressure < 30 % < 30\% < 30% ),

K c K_c K c ​ is the rupture disk combination factor ( 1.0 1.0 1.0 without disk, 0.9 0.9 0.9 if disk installed upstream),

T T T is relieving temperature ( ∘ R = ∘ F + 459.67 ^\circ\text{R} = ^\circ\text{F} + 459.67 ∘ R = ∘ F + 459.67 ).

7. Fanno Flow vs. Isothermal Flow in Process Piping

When compressible gas flows through a long conduit of constant cross-sectional area, friction drives changes in fluid properties:

Fanno Flow (Adiabatic Pipe Flow with Wall Friction)

In insulated process piping or short relief header lines, heat transfer is negligible ( q = 0 q = 0 q = 0 ), so stagnation temperature remains constant ( T 0 = constant T_0 = \text{constant} T 0 ​ = constant ):

Friction accelerates a subsonic gas flow ( d M a / d x > 0 dMa/dx > 0 d M a / d x > 0 ). As velocity increases, static pressure P P P and static temperature T T T drop.

The maximum possible length of straight pipe before choking occurs at the exit ( M a = 1.0 Ma = 1.0 M a = 1.0 ) is the limiting length ( L ∗ L^* L ∗ ): f D L ∗ D = 1 − M a 2 k M a 2 + ( k + 1 2 k ) ln ⁡ [ ( k + 1 ) M a 2 2 + ( k − 1 ) M a 2 ] \frac{f_D L^*}{D} = \frac{1 - Ma^2}{k Ma^2} + \left(\frac{k + 1}{2k}\right) \ln\left[ \frac{(k + 1) Ma^2}{2 + (k - 1) Ma^2} \right] D f D ​ L ∗ ​ = k M a 2 1 − M a 2 ​ + ( 2 k k + 1 ​ ) ln [ 2 + ( k − 1 ) M a 2 ( k + 1 ) M a 2 ​ ]

If the actual pipe length exceeds L ∗ L^* L ∗ , the upstream pressure P 0 P_0 P 0 ​ must increase or the inlet mass flow rate will decrease (choking at the pipe exit).

Isothermal Flow (Gas Flow with Heat Transfer Through Uninsulated Walls)

In long, uninsulated buried transmission pipelines, rapid heat conduction through the pipe wall maintains the gas at constant temperature ( T = T a m b i e n t = constant T = T_{ambient} = \text{constant} T = T ambi e n t ​ = constant ):

As pressure drops along the pipeline due to wall friction, gas expands, density decreases, and velocity rises.

Unlike adiabatic Fanno flow, the limiting maximum velocity in isothermal flow is not sonic ( M a = 1 Ma = 1 M a = 1 ), but rather: v l i m i t = R T M = c k ⟹ M a l i m i t = 1 k v_{limit} = \sqrt{\frac{R T}{M}} = \frac{c}{\sqrt{k}} \implies Ma_{limit} = \frac{1}{\sqrt{k}} v l imi t ​ = M RT ​ ​ = k ​ c ​ ⟹ M a l imi t ​ = k ​ 1 ​ For air ( k = 1.4 k = 1.4 k = 1.4 ), isothermal flow chokes when M a = 1 / 1.4 = 0.845 Ma = 1/\sqrt{1.4} = 0.845 M a = 1/ 1.4 ​ = 0.845 .

8. Summary Table: Compressible Flow Regimes and Governing Equations

Regime / Phenomenon Governing Parameter Critical Formula Practical Process Implication

Incompressible Threshold M a ≤ 0.30 Ma \le 0.30 M a ≤ 0.30 or Δ P / P 1 ≤ 0.10 \Delta P/P_1 \le 0.10 Δ P / P 1 ​ ≤ 0.10 ρ = constant \rho = \text{constant} ρ = constant Standard Darcy-Weisbach head loss equations apply without density correction.

Acoustic Speed Isentropic wave speed c = k R T / M c = \sqrt{k R T / M} c = k RT / M ​ Speed of sound increases with temperature; independent of static pressure.

Critical Pressure Ratio Choking condition ( M a = 1 Ma = 1 M a = 1 ) r c = ( 2 k + 1 ) k k − 1 r_c = \left(\frac{2}{k+1}\right)^{\frac{k}{k-1}} r c ​ = ( k + 1 2 ​ ) k − 1 k ​ Flow chokes when backpressure P b ≤ P ∗ P_b \le P^* P b ​ ≤ P ∗ ; r c ≈ 0.528 r_c \approx 0.528 r c ​ ≈ 0.528 for air, 0.544 0.544 0.544 for methane.

Choked Mass Flow Maximum mass flux m ˙ ∝ P 0 A t / T 0 \dot{m} \propto P_0 A_t / \sqrt{T_0} m ˙ ∝ P 0 ​ A t ​ / T 0 ​ ​ Increasing upstream pressure increases flow linearly; lowering backpressure does nothing.

Adiabatic Pipe Flow (Fanno) Constant T 0 T_0 T 0 ​ with friction M a e x i t = 1.0 Ma_{exit} = 1.0 M a e x i t ​ = 1.0 at L ∗ L^* L ∗ Subsonic gas accelerates toward exit; pipe chokes at the discharge terminus.

Isothermal Pipe Flow Constant T T T with friction M a e x i t = 1 / k Ma_{exit} = 1/\sqrt{k} M a e x i t ​ = 1/ k ​ Long buried pipelines choke at M a < 1.0 Ma < 1.0 M a < 1.0 due to thermal equilibration with soil.

  • 9. Step-by-Step Worked Numerical Example: High-Pressure Blowdown Orifice
  • Problem Statement

An emergency depressuring restriction orifice is installed in an emergency blowdown line connected to a high-pressure natural gas treator. The treator contains dry methane gas ( M = 16.04 kg/kmol M = 16.04\text{ kg/kmol} M = 16.04 kg/kmol , k = 1.31 k = 1.31 k = 1.31 , compressibility factor Z ≈ 1.0 Z \approx 1.0 Z ≈ 1.0 ) at an upstream stagnation pressure of P 0 = 4.00 MPa(a) = 4 , 000 kPa(a) P_0 = 4.00\text{ MPa(a)} = 4,000\text{ kPa(a)} P 0 ​ = 4.00 MPa(a) = 4 , 000 kPa(a) and a stagnation temperature of T 0 = 310.0 K T_0 = 310.0\text{ K} T 0 ​ = 310.0 K ( 36.85 ∘ C 36.85^\circ\text{C} 36.8 5 ∘ C ). The orifice discharges into an atmospheric flare collection header maintained at a backpressure of P b = 300.0 kPa(a) P_b = 300.0\text{ kPa(a)} P b ​ = 300.0 kPa(a) ( 3.00 bar(a) 3.00\text{ bar(a)} 3.00 bar(a) ).

The restriction orifice bore diameter is d t = 25.0 mm = 0.0250 m d_t = 25.0\text{ mm} = 0.0250\text{ m} d t ​ = 25.0 mm = 0.0250 m , and the calibrated discharge coefficient is C d = 0.950 C_d = 0.950 C d ​ = 0.950 . The universal gas constant is R = 8 , 314.5 J/(kmol ⋅ K) R = 8,314.5\text{ J/(kmol}\cdot\text{K)} R = 8 , 314.5 J/(kmol ⋅ K) .

Determine:

The critical pressure ratio P ∗ / P 0 P^* / P_0 P ∗ / P 0 ​ and the critical pressure P ∗ P^* P ∗ .

Whether the restriction orifice is choked.

The static temperature T ∗ T^* T ∗ and sonic speed c ∗ c^* c ∗ at the orifice throat.

The gas density at the throat ρ ∗ \rho^* ρ ∗ .

The choked mass flow rate m ˙ c h o k e d \dot{m}_{choked} m ˙ c h o k e d ​ in kilograms per second ( kg/s \text{kg/s} kg/s ) and kilograms per hour ( kg/h \text{kg/h} kg/h ).

Solution

Step 1: Calculate the critical pressure ratio ( P ∗ / P 0 P^* / P_0 P ∗ / P 0 ​ ) and critical pressure ( P ∗ P^* P ∗ ). Using the isentropic sonic relation for k = 1.31 k = 1.31 k = 1.31 : P ∗ P 0 = ( 2 k + 1 ) k k − 1 = ( 2 1.31 + 1 ) 1.31 1.31 − 1 = ( 2 2.31 ) 1.31 0.31 = ( 0.865801 ) 4.2258 \frac{P^*}{P_0} = \left(\frac{2}{k + 1}\right)^{\frac{k}{k - 1}} = \left(\frac{2}{1.31 + 1}\right)^{\frac{1.31}{1.31 - 1}} = \left(\frac{2}{2.31}\right)^{\frac{1.31}{0.31}} = (0.865801)^{4.2258} P 0 ​ P ∗ ​ = ( k + 1 2 ​ ) k − 1 k ​ = ( 1.31 + 1 2 ​ ) 1.31 − 1 1.31 ​ = ( 2.31 2 ​ ) 0.31 1.31 ​ = ( 0.865801 ) 4.2258

Evaluating the power: ln ⁡ ( 0.865801 ) = − 0.144101 \ln(0.865801) = -0.144101 ln ( 0.865801 ) = − 0.144101 4.2258 × ( − 0.144101 ) = − 0.60894 4.2258 \times (-0.144101) = -0.60894 4.2258 × ( − 0.144101 ) = − 0.60894 P ∗ P 0 = e − 0.60894 = 0.54393 ≈ 0.544 \frac{P^*}{P_0} = e^{-0.60894} = 0.54393 \approx 0.544 P 0 ​ P ∗ ​ = e − 0.60894 = 0.54393 ≈ 0.544

Calculate the absolute critical pressure P ∗ P^* P ∗ : P ∗ = 0.54393 × P 0 = 0.54393 × 4 , 000 kPa = 2 , 175.7 kPa(a) ≈ 2.176 MPa(a) P^* = 0.54393 \times P_0 = 0.54393 \times 4,000\text{ kPa} = 2,175.7\text{ kPa(a)} \approx 2.176\text{ MPa(a)} P ∗ = 0.54393 × P 0 ​ = 0.54393 × 4 , 000 kPa = 2 , 175.7 kPa(a) ≈ 2.176 MPa(a)

Step 2: Determine if the flow is choked. Compare the downstream flare header pressure P b P_b P b ​ to the critical throat pressure P ∗ P^* P ∗ : P b = 300.0 kPa(a) < P ∗ = 2 , 175.7 kPa(a) P_b = 300.0\text{ kPa(a)} < P^* = 2,175.7\text{ kPa(a)} P b ​ = 300.0 kPa(a) < P ∗ = 2 , 175.7 kPa(a) P b P 0 = 300.0 4 , 000.0 = 0.0750 ≪ 0.544 \frac{P_b}{P_0} = \frac{300.0}{4,000.0} = 0.0750 \ll 0.544 P 0 ​ P b ​ ​ = 4 , 000.0 300.0 ​ = 0.0750 ≪ 0.544

Because the receiver backpressure is substantially below the critical choking pressure, the orifice is completely choked ( M a t = 1.0 Ma_t = 1.0 M a t ​ = 1.0 ) . The static pressure at the orifice throat is fixed at P t = P ∗ = 2 , 175.7 kPa(a) P_t = P^* = 2,175.7\text{ kPa(a)} P t ​ = P ∗ = 2 , 175.7 kPa(a) , regardless of the 300 kPa 300\text{ kPa} 300 kPa header pressure.

Step 3: Calculate static temperature ( T ∗ T^* T ∗ ) and sonic velocity ( c ∗ c^* c ∗ ) at the throat. The throat temperature under choked isentropic expansion is: T ∗ = T 0 ( 2 k + 1 ) = 310.0 K × ( 2 2.31 ) = 310.0 × 0.865801 = 268.40 K ( − 4.75 ∘ C ) T^* = T_0 \left(\frac{2}{k + 1}\right) = 310.0\text{ K} \times \left(\frac{2}{2.31}\right) = 310.0 \times 0.865801 = 268.40\text{ K} \quad (-4.75^\circ\text{C}) T ∗ = T 0 ​ ( k + 1 2 ​ ) = 310.0 K × ( 2.31 2 ​ ) = 310.0 × 0.865801 = 268.40 K ( − 4.7 5 ∘ C )

The specific gas constant for methane is: R s p = R M = 8 , 314.5 J/(kmol ⋅ K) 16.04 kg/kmol = 518.36 J/(kg ⋅ K) R_{sp} = \frac{R}{M} = \frac{8,314.5\text{ J/(kmol}\cdot\text{K)}}{16.04\text{ kg/kmol}} = 518.36\text{ J/(kg}\cdot\text{K)} R s p ​ = M R ​ = 16.04 kg/kmol 8 , 314.5 J/(kmol ⋅ K) ​ = 518.36 J/(kg ⋅ K)

The sonic velocity at the throat is: c ∗ = k R s p T ∗ = 1.31 × 518.36 J/(kg ⋅ K) × 268.40 K = 182 , 258 m 2 / s 2 = 426.92 m/s c^* = \sqrt{k R_{sp} T^*} = \sqrt{1.31 \times 518.36\text{ J/(kg}\cdot\text{K)} \times 268.40\text{ K}} = \sqrt{182,258\text{ m}^2/\text{s}^2} = 426.92\text{ m/s} c ∗ = k R s p ​ T ∗ ​ = 1.31 × 518.36 J/(kg ⋅ K) × 268.40 K ​ = 182 , 258 m 2 / s 2 ​ = 426.92 m/s

Step 4: Calculate gas density at the throat ( ρ ∗ \rho^* ρ ∗ ). Using the ideal gas equation of state at throat conditions ( P ∗ , T ∗ P^*, T^* P ∗ , T ∗ ): ρ ∗ = P ∗ M R T ∗ = 2 , 175.7 × 10 3 Pa × 16.04 kg/kmol 8 , 314.5 J/(kmol ⋅ K) × 268.40 K = 34 , 898 , 228 2 , 231 , 612 = 15.638 kg/m 3 \rho^* = \frac{P^* M}{R T^*} = \frac{2,175.7 \times 10^3\text{ Pa} \times 16.04\text{ kg/kmol}}{8,314.5\text{ J/(kmol}\cdot\text{K)} \times 268.40\text{ K}} = \frac{34,898,228}{2,231,612} = 15.638\text{ kg/m}^3 ρ ∗ = R T ∗ P ∗ M ​ = 8 , 314.5 J/(kmol ⋅ K) × 268.40 K 2 , 175.7 × 1 0 3 Pa × 16.04 kg/kmol ​ = 2 , 231 , 612 34 , 898 , 228 ​ = 15.638 kg/m 3

Step 5: Calculate choked mass flow rate ( m ˙ c h o k e d \dot{m}_{choked} m ˙ c h o k e d ​ ). The cross-sectional throat area is: A t = π 4 d t 2 = π 4 ( 0.0250 m ) 2 = 4.9087 × 10 − 4 m 2 A_t = \frac{\pi}{4} d_t^2 = \frac{\pi}{4} (0.0250\text{ m})^2 = 4.9087 \times 10^{-4}\text{ m}^2 A t ​ = 4 π ​ d t 2 ​ = 4 π ​ ( 0.0250 m ) 2 = 4.9087 × 1 0 − 4 m 2

The mass flow rate is: m ˙ c h o k e d = C d A t ρ ∗ c ∗ = 0.950 × ( 4.9087 × 10 − 4 m 2 ) × 15.638 kg/m 3 × 426.92 m/s \dot{m}_{choked} = C_d A_t \rho^* c^* = 0.950 \times (4.9087 \times 10^{-4}\text{ m}^2) \times 15.638\text{ kg/m}^3 \times 426.92\text{ m/s} m ˙ c h o k e d ​ = C d ​ A t ​ ρ ∗ c ∗ = 0.950 × ( 4.9087 × 1 0 − 4 m 2 ) × 15.638 kg/m 3 × 426.92 m/s m ˙ c h o k e d = 0.950 × 3.2771 kg/s = 3.113 kg/s \dot{m}_{choked} = 0.950 \times 3.2771\text{ kg/s} = 3.113\text{ kg/s} m ˙ c h o k e d ​ = 0.950 × 3.2771 kg/s = 3.113 kg/s

Converting to kilograms per hour: m ˙ c h o k e d = 3.1132 kg/s × 3 , 600 s/h = 11 , 208 kg/h ≈ 11 , 210 kg/h \dot{m}_{choked} = 3.1132\text{ kg/s} \times 3,600\text{ s/h} = 11,208\text{ kg/h} \approx 11,210\text{ kg/h} m ˙ c h o k e d ​ = 3.1132 kg/s × 3 , 600 s/h = 11 , 208 kg/h ≈ 11 , 210 kg/h

10. Common PE Exam Traps in Compressible Flow

Using Gauge Pressure in Choking Equations: The critical pressure ratio P ∗ / P 0 P^*/P_0 P ∗ / P 0 ​ and the choked mass flow equation require absolute pressure ( P a b s = P g a u g e + P a t m P_{abs} = P_{gauge} + P_{atm} P ab s ​ = P g a ug e ​ + P a t m ​ ). Using gauge pressure results in severe calculation errors and incorrect choking determinations.

Using Static Temperature Instead of Stagnation Temperature: The total energy of the gas includes its bulk velocity head. In equations for relief valves or blowdown orifices, T 0 T_0 T 0 ​ must be the stagnation temperature of the upstream vessel or reservoir, not the expanded throat temperature.

Assuming Downstream Pressure Drops Increase Choked Flow: Once a nozzle or orifice is choked ( P b ≤ P ∗ P_b \le P^* P b ​ ≤ P ∗ ), further decreases in receiver backpressure do NOT increase mass flow rate. The throat velocity remains fixed at M a = 1.0 Ma = 1.0 M a = 1.0 .

Confusing Specific Gas Constant ( R s p R_{sp} R s p ​ ) with Universal Constant ( R R R ): In metric units, R = 8 , 314.5 J/(kmol ⋅ K) R = 8,314.5\text{ J/(kmol}\cdot\text{K)} R = 8 , 314.5 J/(kmol ⋅ K) . If using specific gas constant R s p = R / M R_{sp} = R/M R s p ​ = R / M , ensure units are in J/(kg ⋅ K) \text{J/(kg}\cdot\text{K)} J/(kg ⋅ K) . In US Customary, forgetting g c = 32.174 g_c = 32.174 g c ​ = 32.174 in c = k g c R T / M c = \sqrt{k g_c R T / M} c = k g c ​ RT / M ​ causes an answer that is off by a factor of 32.174 = 5.67 \sqrt{32.174} = 5.67 32.174 ​ = 5.67 !