Study guide
4.3 Multiphase Flow and Fluidization Principles
PE Chemical Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the PE Chemical Exam How to Use This Guide and the NCEES Handbook
2 Chapter 1: Material Balances & Flowsheet Calculations
1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations
3 Chapter 2: Energy Balances & Thermochemistry
2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances
4 Chapter 3: Fluid Statics & Incompressible Pipe Flow
3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations
5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow
4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up
6 Chapter 5: Thermodynamic Laws & Fundamental Relations
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations
7 Chapter 6: Real Gases & Equations of State
6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions
8 Chapter 7: Phase & Chemical Reaction Equilibria
7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
9 Chapter 8: Heat Transfer Mechanisms & Conduction
8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange
10 Chapter 9: Heat Exchanger Design & Phase Change
9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances
11 Chapter 10: Mass Transfer Fundamentals & Diffusion
10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)
12 Chapter 11: Distillation Operations
11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components
13 Chapter 12: Rate-Controlled & Equilibrium Separations
12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations
14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors
13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations
15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis
14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models
16 Chapter 15: Physical & Transport Properties of Fluids
15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles
17 Chapter 16: Materials of Construction & Corrosion
16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention
18 Chapter 17: Process Safety & Pressure Relief Systems
17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment
19 Chapter 18: Process Control & Engineering Economics
18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems
20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance
19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation
21 Chapter 20: Plant Operation, Reliability & Continuous Improvement
20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting
4.3 Multiphase Flow and Fluidization Principles
Key Takeaways Explain This Topic AI
Two-phase gas-liquid flow regimes (bubble, slug, plug, churn, annular, mist) depend on phase superficial velocities and fluid physical properties; intermittent slug flow presents catastrophic water-hammer risks to piping and supports.
The Lockhart-Martinelli correlation evaluates two-phase frictional pressure drop via the parameter chi = sqrt[(dP/dz)_L / (dP/dz)_G] and the Chisholm two-phase multiplier phi_L^2 = 1 + C/chi + 1/chi^2, where C = 20 for turbulent-turbulent flow.
Frictional pressure drop through stationary packed beds is quantified across all flow regimes by the Ergun equation, which superimposes laminar viscous losses (Blake-Kozeny) and turbulent inertial losses (Burke-Plummer).
Incipient fluidization occurs when upward aerodynamic drag plus buoyancy balances the net weight of the bed particles, establishing the minimum fluidization velocity u_mf from the Ergun equation; once fluidized, the total bed pressure drop remains strictly constant regardless of further velocity increases.
The safe fluidization operating envelope is bounded between the minimum fluidization velocity u_mf and the single-particle terminal settling velocity u_t; operating at superficial velocities u_0 > u_t causes severe particle carryover (elutriation).
Last updated: September 2026
4.3 Multiphase Flow and Fluidization Principles
Multiphase flow phenomena—involving simultaneous movement of gas and liquid, liquid and solid, or gas and solid—are ubiquitous across chemical processing facilities. Examples include boiling reboilers, distillation column trays and packings, petroleum pipelines, catalytic fluidized bed reactors (FCCUs), slurry bubble columns, and pneumatic conveying lines. Because phases exhibit differing densities, viscosities, and velocities, multiphase hydrodynamics cannot be described by single-phase equations. This section covers two-phase gas-liquid pipe flow, the Ergun equation for packed beds, and fluidization principles essential for the NCEES PE Chemical exam.
1. Two-Phase Gas-Liquid Flow Regimes and Hydrodynamic Transitions
When a gas and a liquid flow concurrently through a conduit, the interfacial shear between phases generates distinct morphological configurations known as flow regimes (or flow patterns ). Flow regimes govern phase holdup, heat transfer coefficients, and frictional pressure drops.
Horizontal Flow Regimes
In horizontal piping, gravity acts perpendicular to the flow direction, causing denser liquid to accumulate along the bottom of the pipe:
Stratified Flow (Smooth): At low gas and liquid velocities, liquid flows along the pipe bottom while gas glides smoothly over the top across an undisturbed horizontal interface.
Stratified-Wavy Flow: As gas velocity increases, interfacial shear creates capillary and gravity waves on the liquid surface.
Plug Flow (Elongated Bubble): Liquid is continuous along the bottom and intermittent elongated gas plugs travel along the upper pipe wall.
Slug Flow: Waves grow until their crests bridge the entire pipe diameter, forming high-velocity liquid slugs separated by large gas bubbles (Taylor bubbles). Slug flow is hazardous in industrial plants : the periodic impact of dense liquid slugs produces violent piping vibration, structural fatigue, and severe pressure shocks (water hammer) at pipe elbows and headers.
Annular Flow: At high gas velocities, gas forms a high-speed core carrying atomized entrained droplets, while liquid forms a continuous annular film around the entire pipe circumference.
Dispersed / Mist Flow: At ultra-high gas velocities, the liquid film is stripped from the pipe walls, dispersing into fine droplets suspended in a continuous gas matrix.
Vertical Upward Flow Regimes
In vertical pipes, gravity is aligned with the axis, producing axisymmetric flow patterns:
Bubbly Flow: Gas is dispersed as discrete bubbles in a continuous liquid continuum.
Slug / Plug Flow: Small bubbles coalesce into bullet-shaped Taylor bubbles that fill nearly the entire pipe cross-section, separated by liquid slugs.
Churn Flow: Highly chaotic, churning oscillatory flow occurring when gas momentum shatters liquid slugs before stable annular flow establishes.
Annular Flow: Liquid forms a thin film ascending the pipe wall, surrounding a high-speed gas core containing sheared liquid droplets.
Mist Flow: Complete atomization of the liquid phase into the gas core.
2. Two-Phase Frictional Pressure Drop: The Lockhart-Martinelli Method
The classical engineering framework for evaluating two-phase frictional pressure gradient ( − d P / d z ) T P (-dP/dz)_{TP} ( − d P / d z ) TP is the Lockhart-Martinelli correlation .
The Lockhart-Martinelli Parameter ( χ \chi χ )
Define the parameter χ \chi χ as the square root of the ratio of the frictional pressure gradient if the liquid phase flowed alone in the conduit at its superficial rate, to the frictional pressure gradient if the gas phase flowed alone: χ = ( − d P / d z ) L ( − d P / d z ) G \chi = \sqrt{\frac{(-dP/dz)_L}{(-dP/dz)_G}} χ = ( − d P / d z ) G ( − d P / d z ) L
where ( − d P / d z ) L (-dP/dz)_L ( − d P / d z ) L and ( − d P / d z ) G (-dP/dz)_G ( − d P / d z ) G are computed using standard single-phase Darcy-Weisbach formulas based on the superficial velocities u S L = Q L / A c u_{SL} = Q_L / A_c u S L = Q L / A c and u S G = Q G / A c u_{SG} = Q_G / A_c u SG = Q G / A c .
The Turbulent-Turbulent Regime ( χ t t \chi_{tt} χ tt )
When both liquid and gas phases operate in the turbulent regime ( R e S L > 4 , 000 Re_{SL} > 4,000 R e S L > 4 , 000 and R e S G > 4 , 000 Re_{SG} > 4,000 R e SG > 4 , 000 ), applying the Blasius friction factor ( f ∝ R e − 0.20 f \propto Re^{-0.20} f ∝ R e − 0.20 ) gives the explicit expression for χ t t \chi_{tt} χ tt in terms of gas mass quality x = m ˙ G / ( m ˙ L + m ˙ G ) x = \dot{m}_G / (\dot{m}_L + \dot{m}_G) x = m ˙ G / ( m ˙ L + m ˙ G ) : χ t t = ( 1 − x x ) 0.9 ( ρ G ρ L ) 0.5 ( μ L μ G ) 0.1 \chi_{tt} = \left(\frac{1 - x}{x}\right)^{0.9} \left(\frac{\rho_G}{\rho_L}\right)^{0.5} \left(\frac{\mu_L}{\mu_G}\right)^{0.1} χ tt = ( x 1 − x ) 0.9 ( ρ L ρ G ) 0.5 ( μ G μ L ) 0.1
Two-Phase Multipliers ( ϕ L 2 \phi_L^2 ϕ L 2 and ϕ G 2 \phi_G^2 ϕ G 2 )
The total two-phase frictional pressure drop is determined by multiplying the single-phase pressure drop by the two-phase multiplier (correlated by Chisholm): ( d P d z ) T P = ϕ L 2 ( d P d z ) L = ϕ G 2 ( d P d z ) G \left(\frac{dP}{dz}\right)_{TP} = \phi_L^2 \left(\frac{dP}{dz}\right)_L = \phi_G^2 \left(\frac{dP}{dz}\right)_G ( d z d P ) TP = ϕ L 2 ( d z d P ) L = ϕ G 2 ( d z d P ) G ϕ L 2 = 1 + C χ + 1 χ 2 \phi_L^2 = 1 + \frac{C}{\chi} + \frac{1}{\chi^2} ϕ L 2 = 1 + χ C + χ 2 1 ϕ G 2 = 1 + C χ + χ 2 \phi_G^2 = 1 + C \chi + \chi^2 ϕ G 2 = 1 + C χ + χ 2
Chisholm Parameter ( C C C ) Selection Matrix
The dimensionless constant C C C depends on the flow regime of each independent phase:
Liquid Phase Regime Gas Phase Regime Regime Designation Chisholm Parameter ( C C C )
Turbulent ( R e L > 4 , 000 Re_L > 4,000 R e L > 4 , 000 ) Turbulent ( R e G > 4 , 000 Re_G > 4,000 R e G > 4 , 000 ) t t tt tt C = 20 C = 20 C = 20
Viscous (Laminar) ( R e L < 2 , 100 Re_L < 2,100 R e L < 2 , 100 ) Turbulent ( R e G > 4 , 000 Re_G > 4,000 R e G > 4 , 000 ) v t vt v t C = 12 C = 12 C = 12
Turbulent ( R e L > 4 , 000 Re_L > 4,000 R e L > 4 , 000 ) Viscous (Laminar) ( R e G < 2 , 100 Re_G < 2,100 R e G < 2 , 100 ) t v tv t v C = 10 C = 10 C = 10
Viscous (Laminar) ( R e L < 2 , 100 Re_L < 2,100 R e L < 2 , 100 ) Viscous (Laminar) ( R e G < 2 , 100 Re_G < 2,100 R e G < 2 , 100 ) v v vv vv C = 5 C = 5 C = 5
3. Flow Through Packed Beds and the Ergun Equation
In chemical reactors (fixed-bed catalytic converters), absorbers, and filter media, fluid percolates through a stationary bed of granular solid particles. Sabri Ergun (1952) established that the total frictional pressure gradient through a packed bed is the sum of viscous laminar energy losses (viscous drag along particle surfaces) and turbulent kinetic energy losses (inertial form drag in tortuous interstitial expansions/contractions): Δ P L = 150 ( 1 − ε ) 2 ε 3 μ u 0 d p 2 ⏟ Viscous Term (Blake-Kozeny) + 1.75 1 − ε ε 3 ρ u 0 2 d p ⏟ Inertial Term (Burke-Plummer) \frac{\Delta P}{L} = \underbrace{150 \frac{(1 - \varepsilon)^2}{\varepsilon^3} \frac{\mu u_0}{d_p^2}}_{\text{Viscous Term (Blake-Kozeny)}} + \underbrace{1.75 \frac{1 - \varepsilon}{\varepsilon^3} \frac{\rho u_0^2}{d_p}}_{\text{Inertial Term (Burke-Plummer)}} L Δ P = Viscous Term (Blake-Kozeny) 150 ε 3 ( 1 − ε ) 2 d p 2 μ u 0 + Inertial Term (Burke-Plummer) 1.75 ε 3 1 − ε d p ρ u 0 2
where:
Δ P / L \Delta P / L Δ P / L is the pressure drop per unit length of packed bed ( Pa/m \text{Pa/m} Pa/m ),
ε = V v o i d / V b e d \varepsilon = V_{void} / V_{bed} ε = V v o i d / V b e d is the bed void fraction (porosity), typically 0.35 − 0.45 0.35 - 0.45 0.35 − 0.45 for random spherical packings,
u 0 = Q / A c u_0 = Q / A_c u 0 = Q / A c is the superficial fluid velocity (empty tube velocity, m/s \text{m/s} m/s ),
d p d_p d p is the effective particle diameter ( m \text{m} m ), defined for non-spherical particles as d p = ϕ s d v d_p = \phi_s d_v d p = ϕ s d v (where ϕ s \phi_s ϕ s is sphericity and d v d_v d v is volume-equivalent sphere diameter),
μ \mu μ is fluid dynamic viscosity ( Pa ⋅ s \text{Pa}\cdot\text{s} Pa ⋅ s ),
ρ \rho ρ is fluid mass density ( kg/m 3 \text{kg/m}^3 kg/m 3 ).
Asymptotic Regimes of the Ergun Equation
Define the particle Reynolds number based on superficial velocity: R e p = ρ u 0 d p μ ( 1 − ε ) Re_p = \frac{\rho u_0 d_p}{\mu (1 - \varepsilon)} R e p = μ ( 1 − ε ) ρ u 0 d p
Laminar Flow ( R e p < 10 Re_p < 10 R e p < 10 ): The viscous term dominates ( > 90 % > 90\% > 90% of total loss). The equation reduces to the Blake-Kozeny equation (analogous to Darcy's law for porous media): Δ P L = 150 ( 1 − ε ) 2 ε 3 μ u 0 d p 2 ⟹ Δ P ∝ u 0 \frac{\Delta P}{L} = 150 \frac{(1 - \varepsilon)^2}{\varepsilon^3} \frac{\mu u_0}{d_p^2} \implies \Delta P \propto u_0 L Δ P = 150 ε 3 ( 1 − ε ) 2 d p 2 μ u 0 ⟹ Δ P ∝ u 0
Highly Turbulent Flow ( R e p > 1 , 000 Re_p > 1,000 R e p > 1 , 000 ): Inertial form drag dominates. The equation reduces to the Burke-Plummer equation : Δ P L = 1.75 1 − ε ε 3 ρ u 0 2 d p ⟹ Δ P ∝ u 0 2 \frac{\Delta P}{L} = 1.75 \frac{1 - \varepsilon}{\varepsilon^3} \frac{\rho u_0^2}{d_p} \implies \Delta P \propto u_0^2 L Δ P = 1.75 ε 3 1 − ε d p ρ u 0 2 ⟹ Δ P ∝ u 0 2
4. Fluidization Fundamentals and Minimum Fluidization Velocity ( u m f u_{mf} u m f )
Consider a vertical column packed with solid particles supported on a porous gas distributor plate. Fluid is pumped upward through the bed at steadily increasing superficial velocity u 0 u_0 u 0 . Bed Pressure Drop (Delta P)
- ^
- | Fixed Bed Fluidized Bed (Bubbling/Slugging)
- | (Delta P increases with u0) (Delta P = CONSTANT = Buoyant Weight)
- Delta P | /------------------------------------------------------------
- mf | /*
- | / *
- | / * Peak (interlocking friction)
- | /
- | /
- | /
- +--------------+-------------------------------------------------------------> Superficial
- u_mf u_t Velocity (u0)
- Incipient Fluidization Elutriation Limit
- The Incipient Fluidization Condition
As upward superficial velocity increases, the upward aerodynamic drag force and buoyant force exerted by the fluid on the particles increase. At a critical velocity known as the minimum fluidization velocity ( u m f u_{mf} u m f ), the net upward fluid forces exactly balance the downward gravitational weight of the solid particles: Upward Pressure Force = Net Buoyant Weight of Bed \text{Upward Pressure Force} = \text{Net Buoyant Weight of Bed} Upward Pressure Force = Net Buoyant Weight of Bed Δ P b e d A c = W s o l i d s − F b u o y a n c y = ( 1 − ε m f ) A c L m f ( ρ p − ρ f ) g \Delta P_{bed} A_c = W_{solids} - F_{buoyancy} = (1 - \varepsilon_{mf}) A_c L_{mf} (\rho_p - \rho_f) g Δ P b e d A c = W so l i d s − F b u oy an cy = ( 1 − ε m f ) A c L m f ( ρ p − ρ f ) g
Dividing by bed volume A c L m f A_c L_{mf} A c L m f yields the fundamental bed pressure drop equation at fluidization : Δ P b e d L m f = ( 1 − ε m f ) ( ρ p − ρ f ) g \frac{\Delta P_{bed}}{L_{mf}} = (1 - \varepsilon_{mf}) (\rho_p - \rho_f) g L m f Δ P b e d = ( 1 − ε m f ) ( ρ p − ρ f ) g
where:
L m f L_{mf} L m f is bed height at minimum fluidization,
ε m f \varepsilon_{mf} ε m f is void fraction at incipient fluidization (typically 0.40 − 0.45 0.40 - 0.45 0.40 − 0.45 ),
ρ p \rho_p ρ p is solid particle density,
ρ f \rho_f ρ f is fluidizing fluid density.
Deriving u m f u_{mf} u m f from the Ergun Equation
Equating the hydrostatic buoyant bed weight gradient to the Ergun pressure drop at voidage ε m f \varepsilon_{mf} ε m f : ( 1 − ε m f ) ( ρ p − ρ f ) g = 150 ( 1 − ε m f ) 2 ε m f 3 μ u m f d p 2 + 1.75 1 − ε m f ε m f 3 ρ f u m f 2 d p (1 - \varepsilon_{mf}) (\rho_p - \rho_f) g = 150 \frac{(1 - \varepsilon_{mf})^2}{\varepsilon_{mf}^3} \frac{\mu u_{mf}}{d_p^2} + 1.75 \frac{1 - \varepsilon_{mf}}{\varepsilon_{mf}^3} \frac{\rho_f u_{mf}^2}{d_p} ( 1 − ε m f ) ( ρ p − ρ f ) g = 150 ε m f 3 ( 1 − ε m f ) 2 d p 2 μ u m f + 1.75 ε m f 3 1 − ε m f d p ρ f u m f 2
Dividing through by ( 1 − ε m f ) (1 - \varepsilon_{mf}) ( 1 − ε m f ) and expressing in dimensionless form yields a quadratic in terms of the particle Reynolds number at minimum fluidization ( R e p , m f = ρ f u m f d p μ Re_{p,mf} = \frac{\rho_f u_{mf} d_p}{\mu} R e p , m f = μ ρ f u m f d p ): 1.75 ε m f 3 R e p , m f 2 + 150 ( 1 − ε m f ) ε m f 3 R e p , m f = A r \frac{1.75}{\varepsilon_{mf}^3} Re_{p,mf}^2 + \frac{150 (1 - \varepsilon_{mf})}{\varepsilon_{mf}^3} Re_{p,mf} = Ar ε m f 3 1.75 R e p , m f 2 + ε m f 3 150 ( 1 − ε m f ) R e p , m f = A r
where A r Ar A r is the dimensionless Archimedes number , characterizing the ratio of gravitational/buoyancy forces to viscous forces: A r = d p 3 ρ f ( ρ p − ρ f ) g μ 2 Ar = \frac{d_p^3 \rho_f (\rho_p - \rho_f) g}{\mu^2} A r = μ 2 d p 3 ρ f ( ρ p − ρ f ) g
Analytical Solution for Small Particles (Laminar Flow, R e p , m f < 20 Re_{p,mf} < 20 R e p , m f < 20 )
For fine catalyst particles and powders where A r < 1 , 000 Ar < 1,000 A r < 1 , 000 , flow at incipient fluidization is strictly laminar ( R e p , m f < 20 Re_{p,mf} < 20 R e p , m f < 20 ). The inertial quadratic term is negligible, yielding the direct formula for u m f u_{mf} u m f : ν m f = d p 2 ( ρ p − ρ f ) g 150 μ ( ε m f 3 1 − ε m f ) \nu_{mf} = \frac{d_p^2 (\rho_p - \rho_f) g}{150 \mu} \left(\frac{\varepsilon_{mf}^3}{1 - \varepsilon_{mf}}\right) ν m f = 150 μ d p 2 ( ρ p − ρ f ) g ( 1 − ε m f ε m f 3 )
5. Bed Pressure Drop Dynamics and Expansion Above u m f u_{mf} u m f
A critical conceptual principle tested on the PE exam is the behavior of bed pressure drop Δ P b e d \Delta P_{bed} Δ P b e d as superficial velocity increases beyond u m f u_{mf} u m f :
Fixed Bed Regime ( u 0 < u m f u_0 < u_{mf} u 0 < u m f ): The particles remain stationary in physical contact. Bed voidage ε \varepsilon ε and bed height L L L remain constant. By the Ergun equation, Δ P b e d \Delta P_{bed} Δ P b e d increases monotonically (linearly at low u 0 u_0 u 0 , quadratically at higher u 0 u_0 u 0 ).
Incipient Fluidization ( u 0 = u m f u_0 = u_{mf} u 0 = u m f ): Particles unlock and begin to float. A slight transient peak in Δ P \Delta P Δ P often occurs just before u m f u_{mf} u m f to overcome mechanical particle interlocking.
Fluidized Bed Regime ( u 0 > u m f u_0 > u_{mf} u 0 > u m f ): As velocity increases beyond u m f u_{mf} u m f , the total bed pressure drop remains strictly constant! Δ P b e d = M b e d , t o t a l g A c ( 1 − ρ f ρ p ) = constant \Delta P_{bed} = \frac{M_{bed,total} g}{A_c} \left(1 - \frac{\rho_f}{\rho_p}\right) = \text{constant} Δ P b e d = A c M b e d , t o t a l g ( 1 − ρ p ρ f ) = constant The excess gas passes through the bed as bubbles (in bubbling beds). The bed expands vertically ( L > L m f L > L_{mf} L > L m f ), increasing the void fraction ε \varepsilon ε such that the upward drag per unit particle remains exactly equal to particle weight.
6. Geldart Particle Classification System
D. Geldart (1973) categorized solids for gas fluidization into four distinct groups based on mean particle diameter d p d_p d p and particle-fluid density difference ( ρ p − ρ g ) (\rho_p - \rho_g) ( ρ p − ρ g ) :
Geldart Group Designation Particle Size Range Fluidization Characteristics Industrial Chemical Examples
Group A Aeratable 30 − 100 μ m 30 - 100\ \mu\text{m} 30 − 100 μ m ( ρ p < 1 , 400 kg/m 3 \rho_p < 1,400\text{ kg/m}^3 ρ p < 1 , 400 kg/m 3 ) Expands significantly and smoothly before bubbling begins ( u m b > u m f u_{mb} > u_{mf} u mb > u m f ); slow deaeration rate. Fluid Catalytic Cracking (FCC) catalysts; Fischer-Tropsch catalyst.
Group B Sand-like / Bubbling 100 − 800 μ m 100 - 800\ \mu\text{m} 100 − 800 μ m ( ρ p = 1 , 400 − 4 , 000 \rho_p = 1,400 - 4,000 ρ p = 1 , 400 − 4 , 000 ) Bubbles form immediately at incipient fluidization ( u m b ≈ u m f u_{mb} \approx u_{mf} u mb ≈ u m f ); moderate bed expansion. Coarse silica sand, coal gasifier granules, polymerization catalysts.
Group C Cohesive / Fine < 30 μ m < 30\ \mu\text{m} < 30 μ m Very difficult to fluidize smoothly; interparticle Van der Waals forces cause channeling, lifting, and rat-holing. Flour, fine talc, face powders, submicron paint pigments, cement dust.
Group D Spoutable / Coarse > 1 , 000 μ m > 1,000\ \mu\text{m} > 1 , 000 μ m ( > 1 mm > 1\text{ mm} > 1 mm ) Deep spouting beds; gas jets penetrate center; bubbles coalesce into large slugs. Coffee beans, roasted grains, polymer pellets, metal ores, roasted catalyst.
7. Terminal Settling Velocity ( u t u_t u t ) and Elutriation Limits
If gas velocity through a fluidized bed is increased continuously, particles eventually become entrained and are carried out of the vessel. The upper physical operating limit of a stationary fluidized bed is the terminal settling velocity ( u t u_t u t ) of a single particle.
Single-Particle Settling Balance
Setting drag force equal to net buoyant particle weight: F D = C D ( π 4 d p 2 ) ( 1 2 ρ f u t 2 ) = ( π 6 d p 3 ) ( ρ p − ρ f ) g F_D = C_D \left(\frac{\pi}{4} d_p^2\right) \left(\frac{1}{2}\rho_f u_t^2\right) = \left(\frac{\pi}{6} d_p^3\right) (\rho_p - \rho_f) g F D = C D ( 4 π d p 2 ) ( 2 1 ρ f u t 2 ) = ( 6 π d p 3 ) ( ρ p − ρ f ) g
Solving for u t u_t u t : ν t = 4 d p ( ρ p − ρ f ) g 3 C D ρ f \nu_t = \sqrt{\frac{4 d_p (\rho_p - \rho_f) g}{3 C_D \rho_f}} ν t = 3 C D ρ f 4 d p ( ρ p − ρ f ) g
Regimes of Particle Settling
Stokes' Law Regime ( R e p = ρ f u t d p μ < 1.0 Re_p = \frac{\rho_f u_t d_p}{\mu} < 1.0 R e p = μ ρ f u t d p < 1.0 ): Viscous drag dominates; drag coefficient is C D = 24 / R e p C_D = 24 / Re_p C D = 24/ R e p : u t = g d p 2 ( ρ p − ρ f ) 18 μ u_t = \frac{g d_p^2 (\rho_p - \rho_f)}{18 \mu} u t = 18 μ g d p 2 ( ρ p − ρ f )
Intermediate Regime ( 1.0 ≤ R e p ≤ 1 , 000 1.0 \le Re_p \le 1,000 1.0 ≤ R e p ≤ 1 , 000 ): Transition drag: C D ≈ 18.5 R e p 0.6 ⟹ u t = 0.153 g 0.71 d p 1.14 ( ρ p − ρ f ) 0.71 ρ f 0.29 μ 0.43 C_D \approx \frac{18.5}{Re_p^{0.6}} \implies u_t = 0.153 \frac{g^{0.71} d_p^{1.14} (\rho_p - \rho_f)^{0.71}}{\rho_f^{0.29} \mu^{0.43}} C D ≈ R e p 0.6 18.5 ⟹ u t = 0.153 ρ f 0.29 μ 0.43 g 0.71 d p 1.14 ( ρ p − ρ f ) 0.71
Newton's Law Regime ( 1 , 000 < R e p < 200 , 000 1,000 < Re_p < 200,000 1 , 000 < R e p < 200 , 000 ): Inertial turbulent form drag dominates; C D ≈ 0.44 C_D \approx 0.44 C D ≈ 0.44 (constant): u t = 1.74 d p ( ρ p − ρ f ) g ρ f u_t = 1.74 \sqrt{\frac{d_p (\rho_p - \rho_f) g}{\rho_f}} u t = 1.74 ρ f d p ( ρ p − ρ f ) g
The Fluidization Operating Window
A stable bubbling or turbulent fluidized bed reactor must operate within the strict velocity window: ν m f < u 0 < u t \nu_{mf} < u_0 < u_t ν m f < u 0 < u t
Operating at u 0 ≥ u t u_0 \ge u_t u 0 ≥ u t triggers pneumatic transport (elutriation), carrying the entire catalyst inventory into overhead cyclones and downstream heat exchangers.
8. Summary Comparison of Gas-Solid Contacting Regimes
Contacting Regime Superficial Velocity ( u 0 u_0 u 0 ) Bed Void Fraction ( ε \varepsilon ε ) Pressure Drop ( Δ P \Delta P Δ P ) Dominant Industrial Application
Fixed Bed 0 < u 0 < u m f 0 < u_0 < u_{mf} 0 < u 0 < u m f Constant ( ≈ 0.40 \approx 0.40 ≈ 0.40 ) Increases with u 0 u_0 u 0 (Ergun) Desulfurization hydrotreaters, packed absorption columns.
Particulate (Smooth) u m f ≤ u 0 < u m b u_{mf} \le u_0 < u_{mb} u m f ≤ u 0 < u mb Expands smoothly ( 0.42 − 0.60 0.42 - 0.60 0.42 − 0.60 ) Constant ( = W b e d / A c = W_{bed}/A_c = W b e d / A c ) Liquid-solid fluidization; Geldart Group A gas systems.
Bubbling Fluidized Bed u m b < u 0 < u m s u_{mb} < u_0 < u_{ms} u mb < u 0 < u m s Moderate expansion ( 0.50 − 0.70 0.50 - 0.70 0.50 − 0.70 ) Constant ( = W b e d / A c = W_{bed}/A_c = W b e d / A c ) Gas-phase polyethylene (Unipol), roasting, coal combustion.
Circulating Bed (CFB) u 0 > u t u_0 > u_t u 0 > u t High voidage ( 0.85 − 0.95 0.85 - 0.95 0.85 − 0.95 ) Low per meter; cyclone return Fluid catalytic cracking (FCC) risers, CFB boilers.
Pneumatic Conveying u 0 ≫ u t u_0 \gg u_t u 0 ≫ u t Dilute phase ( ε > 0.99 \varepsilon > 0.99 ε > 0.99 ) Frictional pipe loss Railcar unloading of pellets, pneumatic ash transfer.
- 9. Step-by-Step Worked Numerical Example: Fluidized Bed Reactor Hydrodynamics
- Problem Statement
A gas-phase catalytic fluidized bed reactor operates at 200 ∘ C 200^\circ\text{C} 20 0 ∘ C and 1.50 MPa(a) 1.50\text{ MPa(a)} 1.50 MPa(a) ( 15.0 bar(a) 15.0\text{ bar(a)} 15.0 bar(a) ) to synthesize an organic intermediate. The fluidizing synthesis gas has a density of ρ f = 7.50 kg/m 3 \rho_f = 7.50\text{ kg/m}^3 ρ f = 7.50 kg/m 3 and dynamic viscosity of μ = 2.00 × 10 − 5 Pa ⋅ s = 0.0200 cP \mu = 2.00 \times 10^{-5}\text{ Pa}\cdot\text{s} = 0.0200\text{ cP} μ = 2.00 × 1 0 − 5 Pa ⋅ s = 0.0200 cP .
The solid catalyst particles are spherical with mean diameter d p = 100.0 μ m = 1.00 × 10 − 4 m d_p = 100.0\ \mu\text{m} = 1.00 \times 10^{-4}\text{ m} d p = 100.0 μ m = 1.00 × 1 0 − 4 m and particle density ρ p = 1 , 600.0 kg/m 3 \rho_p = 1,600.0\text{ kg/m}^3 ρ p = 1 , 600.0 kg/m 3 . The bed void fraction at minimum fluidization is measured as ε m f = 0.450 \varepsilon_{mf} = 0.450 ε m f = 0.450 .
Calculate:
The buoyant bed pressure drop gradient Δ P b e d / L m f \Delta P_{bed} / L_{mf} Δ P b e d / L m f in kPa/m \text{kPa/m} kPa/m .
The Archimedes number A r Ar A r .
The minimum fluidization velocity u m f u_{mf} u m f in millimeters per second ( mm/s \text{mm/s} mm/s ).
The particle Reynolds number at minimum fluidization R e p , m f Re_{p,mf} R e p , m f to verify the flow regime.
The single-particle terminal settling velocity u t u_t u t using Stokes' law.
The allowable superficial operating velocity window for the reactor.
Solution
Step 1: Calculate bed pressure drop gradient at minimum fluidization. Δ P b e d L m f = ( 1 − ε m f ) ( ρ p − ρ f ) g \frac{\Delta P_{bed}}{L_{mf}} = (1 - \varepsilon_{mf}) (\rho_p - \rho_f) g L m f Δ P b e d = ( 1 − ε m f ) ( ρ p − ρ f ) g ρ p − ρ f = 1 , 600.0 kg/m 3 − 7.50 kg/m 3 = 1 , 592.5 kg/m 3 \rho_p - \rho_f = 1,600.0\text{ kg/m}^3 - 7.50\text{ kg/m}^3 = 1,592.5\text{ kg/m}^3 ρ p − ρ f = 1 , 600.0 kg/m 3 − 7.50 kg/m 3 = 1 , 592.5 kg/m 3 Δ P b e d L m f = ( 1 − 0.450 ) × 1 , 592.5 kg/m 3 × 9.807 m/s 2 = 0.550 × 15 , 617.65 N/m 3 = 8 , 589.7 Pa/m = 8.590 kPa/m \frac{\Delta P_{bed}}{L_{mf}} = (1 - 0.450) \times 1,592.5\text{ kg/m}^3 \times 9.807\text{ m/s}^2 = 0.550 \times 15,617.65\text{ N/m}^3 = 8,589.7\text{ Pa/m} = 8.590\text{ kPa/m} L m f Δ P b e d = ( 1 − 0.450 ) × 1 , 592.5 kg/m 3 × 9.807 m/s 2 = 0.550 × 15 , 617.65 N/m 3 = 8 , 589.7 Pa/m = 8.590 kPa/m
Step 2: Calculate the Archimedes number ( A r Ar A r ). A r = d p 3 ρ f ( ρ p − ρ f ) g μ 2 Ar = \frac{d_p^3 \rho_f (\rho_p - \rho_f) g}{\mu^2} A r = μ 2 d p 3 ρ f ( ρ p − ρ f ) g d p 3 = ( 1.00 × 10 − 4 m ) 3 = 1.00 × 10 − 12 m 3 d_p^3 = (1.00 \times 10^{-4}\text{ m})^3 = 1.00 \times 10^{-12}\text{ m}^3 d p 3 = ( 1.00 × 1 0 − 4 m ) 3 = 1.00 × 1 0 − 12 m 3 μ 2 = ( 2.00 × 10 − 5 Pa ⋅ s ) 2 = 4.00 × 10 − 10 Pa 2 ⋅ s 2 \mu^2 = (2.00 \times 10^{-5}\text{ Pa}\cdot\text{s})^2 = 4.00 \times 10^{-10}\text{ Pa}^2\cdot\text{s}^2 μ 2 = ( 2.00 × 1 0 − 5 Pa ⋅ s ) 2 = 4.00 × 1 0 − 10 Pa 2 ⋅ s 2 A r = ( 1.00 × 10 − 12 ) × 7.50 × 1 , 592.5 × 9.807 4.00 × 10 − 10 = 1.17132 × 10 − 7 4.00 × 10 − 10 = 292.83 Ar = \frac{(1.00 \times 10^{-12}) \times 7.50 \times 1,592.5 \times 9.807}{4.00 \times 10^{-10}} = \frac{1.17132 \times 10^{-7}}{4.00 \times 10^{-10}} = 292.83 A r = 4.00 × 1 0 − 10 ( 1.00 × 1 0 − 12 ) × 7.50 × 1 , 592.5 × 9.807 = 4.00 × 1 0 − 10 1.17132 × 1 0 − 7 = 292.83
Because A r = 292.8 < 1 , 000 Ar = 292.8 < 1,000 A r = 292.8 < 1 , 000 , flow through the bed at minimum fluidization is fully within the laminar regime ( R e p , m f ≪ 20 Re_{p,mf} \ll 20 R e p , m f ≪ 20 ).
Step 3: Calculate minimum fluidization velocity ( u m f u_{mf} u m f ). Using the laminar Blake-Kozeny form of the Ergun equation: ν m f = d p 2 ( ρ p − ρ f ) g 150 μ ( ε m f 3 1 − ε m f ) \nu_{mf} = \frac{d_p^2 (\rho_p - \rho_f) g}{150 \mu} \left(\frac{\varepsilon_{mf}^3}{1 - \varepsilon_{mf}}\right) ν m f = 150 μ d p 2 ( ρ p − ρ f ) g ( 1 − ε m f ε m f 3 )
Evaluate the physical grouping: d p 2 ( ρ p − ρ f ) g 150 μ = ( 1.00 × 10 − 4 m ) 2 × 1 , 592.5 kg/m 3 × 9.807 m/s 2 150 × ( 2.00 × 10 − 5 Pa ⋅ s ) = 1.561765 × 10 − 4 3.00 × 10 − 3 = 0.052059 m/s \frac{d_p^2 (\rho_p - \rho_f) g}{150 \mu} = \frac{(1.00 \times 10^{-4}\text{ m})^2 \times 1,592.5\text{ kg/m}^3 \times 9.807\text{ m/s}^2}{150 \times (2.00 \times 10^{-5}\text{ Pa}\cdot\text{s})} = \frac{1.561765 \times 10^{-4}}{3.00 \times 10^{-3}} = 0.052059\text{ m/s} 150 μ d p 2 ( ρ p − ρ f ) g = 150 × ( 2.00 × 1 0 − 5 Pa ⋅ s ) ( 1.00 × 1 0 − 4 m ) 2 × 1 , 592.5 kg/m 3 × 9.807 m/s 2 = 3.00 × 1 0 − 3 1.561765 × 1 0 − 4 = 0.052059 m/s
Evaluate the voidage function: ε m f 3 1 − ε m f = ( 0.450 ) 3 1 − 0.450 = 0.091125 0.550 = 0.165682 \frac{\varepsilon_{mf}^3}{1 - \varepsilon_{mf}} = \frac{(0.450)^3}{1 - 0.450} = \frac{0.091125}{0.550} = 0.165682 1 − ε m f ε m f 3 = 1 − 0.450 ( 0.450 ) 3 = 0.550 0.091125 = 0.165682
Multiply the two factors: ν m f = 0.052059 m/s × 0.165682 = 0.008625 m/s = 8.625 mm/s ≈ 8.63 mm/s \nu_{mf} = 0.052059\text{ m/s} \times 0.165682 = 0.008625\text{ m/s} = 8.625\text{ mm/s} \approx 8.63\text{ mm/s} ν m f = 0.052059 m/s × 0.165682 = 0.008625 m/s = 8.625 mm/s ≈ 8.63 mm/s
Step 4: Verify the particle Reynolds number at u m f u_{mf} u m f . R e p , m f = ρ f u m f d p μ = 7.50 kg/m 3 × 0.008625 m/s × 1.00 × 10 − 4 m 2.00 × 10 − 5 Pa ⋅ s = 6.4688 × 10 − 6 2.00 × 10 − 5 = 0.323 Re_{p,mf} = \frac{\rho_f u_{mf} d_p}{\mu} = \frac{7.50\text{ kg/m}^3 \times 0.008625\text{ m/s} \times 1.00 \times 10^{-4}\text{ m}}{2.00 \times 10^{-5}\text{ Pa}\cdot\text{s}} = \frac{6.4688 \times 10^{-6}}{2.00 \times 10^{-5}} = 0.323 R e p , m f = μ ρ f u m f d p = 2.00 × 1 0 − 5 Pa ⋅ s 7.50 kg/m 3 × 0.008625 m/s × 1.00 × 1 0 − 4 m = 2.00 × 1 0 − 5 6.4688 × 1 0 − 6 = 0.323
Because R e p , m f = 0.323 ≪ 20 Re_{p,mf} = 0.323 \ll 20 R e p , m f = 0.323 ≪ 20 , the laminar simplification is verified with extreme precision.
Step 5: Calculate single-particle terminal settling velocity ( u t u_t u t ). Assuming the Stokes' law regime ( R e p < 1.0 Re_p < 1.0 R e p < 1.0 ): ν t , S t o k e s = g d p 2 ( ρ p − ρ f ) 18 μ = 9.807 × ( 1.00 × 10 − 4 ) 2 × 1 , 592.5 18 × ( 2.00 × 10 − 5 ) = 1.561765 × 10 − 4 3.60 × 10 − 4 = 0.4338 m/s = 433.8 mm/s \nu_{t,Stokes} = \frac{g d_p^2 (\rho_p - \rho_f)}{18 \mu} = \frac{9.807 \times (1.00 \times 10^{-4})^2 \times 1,592.5}{18 \times (2.00 \times 10^{-5})} = \frac{1.561765 \times 10^{-4}}{3.60 \times 10^{-4}} = 0.4338\text{ m/s} = 433.8\text{ mm/s} ν t , St o k es = 18 μ g d p 2 ( ρ p − ρ f ) = 18 × ( 2.00 × 1 0 − 5 ) 9.807 × ( 1.00 × 1 0 − 4 ) 2 × 1 , 592.5 = 3.60 × 1 0 − 4 1.561765 × 1 0 − 4 = 0.4338 m/s = 433.8 mm/s
Check Reynolds number at terminal velocity: R e p , t = ρ f u t d p μ = 7.50 × 0.4338 × 1.00 × 10 − 4 2.00 × 10 − 5 = 1.63 Re_{p,t} = \frac{\rho_f u_t d_p}{\mu} = \frac{7.50 \times 0.4338 \times 1.00 \times 10^{-4}}{2.00 \times 10^{-5}} = 1.63 R e p , t = μ ρ f u t d p = 2.00 × 1 0 − 5 7.50 × 0.4338 × 1.00 × 1 0 − 4 = 1.63
Because R e p , t = 1.63 Re_{p,t} = 1.63 R e p , t = 1.63 is slightly above 1.0 1.0 1.0 , applying the Schiller-Naumann intermediate drag correction ( C D = 24 R e ( 1 + 0.15 R e 0.687 ) C_D = \frac{24}{Re}(1 + 0.15 Re^{0.687}) C D = R e 24 ( 1 + 0.15 R e 0.687 ) with factor 1 + 0.15 ( 1.63 ) 0.687 = 1.21 1 + 0.15(1.63)^{0.687} = 1.21 1 + 0.15 ( 1.63 ) 0.687 = 1.21 ): ν t , a c t u a l ≈ u t , S t o k e s 1.21 = 0.4338 1.10 = 0.394 m/s = 394 mm/s \nu_{t,actual} \approx \frac{u_{t,Stokes}}{\sqrt{1.21}} = \frac{0.4338}{1.10} = 0.394\text{ m/s} = 394\text{ mm/s} ν t , a c t u a l ≈ 1.21 u t , St o k es = 1.10 0.4338 = 0.394 m/s = 394 mm/s
Step 6: Determine the operational window. The fluidization operating window is: ν m f = 8.63 mm/s < u 0 < u t ≈ 394 mm/s \nu_{mf} = 8.63\text{ mm/s} < u_0 < u_t \approx 394\text{ mm/s} ν m f = 8.63 mm/s < u 0 < u t ≈ 394 mm/s
The ratio of terminal velocity to minimum fluidization velocity is u t / u m f = 394 / 8.63 = 45.7 u_t / u_{mf} = 394 / 8.63 = 45.7 u t / u m f = 394/8.63 = 45.7 . Typically, commercial bubbling beds operate at u 0 ≈ 3 − 6 × u m f u_0 \approx 3 - 6 \times u_{mf} u 0 ≈ 3 − 6 × u m f ( 25 − 50 mm/s 25 - 50\text{ mm/s} 25 − 50 mm/s ), ensuring vigorous fluidization and high catalyst contacting without risking particle elutriation.
10. Common PE Exam Traps in Multiphase Flow and Fluidization
Assuming Bed Pressure Drop Keeps Rising After Fluidization: In fixed beds ( u 0 < u m f u_0 < u_{mf} u 0 < u m f ), pressure drop increases continuously. But once the bed fluidizes ( u 0 ≥ u m f u_0 \ge u_{mf} u 0 ≥ u m f ), the total pressure drop remains strictly constant because the buoyant weight of solids does not change. Excess gas merely forms bubbles.
Confusing Superficial Velocity with Interstitial Pore Velocity: Superficial velocity u 0 = Q / A c u_0 = Q / A_c u 0 = Q / A c is based on the empty column cross-sectional area. The true interstitial pore velocity through the voids is u p o r e = u 0 / ε u_{pore} = u_0 / \varepsilon u p ore = u 0 / ε . The Ergun equation uses superficial velocity u 0 u_0 u 0 .
Omitting the Buoyancy Term in Bed Calculations: Using particle density ρ p \rho_p ρ p instead of buoyant density difference ( ρ p − ρ f ) (\rho_p - \rho_f) ( ρ p − ρ f ) . In high-pressure gas fluidization (where gas density can exceed 20 kg/m 3 20\text{ kg/m}^3 20 kg/m 3 ) or liquid fluidization, neglecting ρ f \rho_f ρ f creates major errors.
Applying Stokes' Law Outside Its Validity Range: Using u t = g d p 2 ( ρ p − ρ f ) / ( 18 μ ) u_t = g d_p^2 (\rho_p - \rho_f) / (18 \mu) u t = g d p 2 ( ρ p − ρ f ) / ( 18 μ ) when R e p > 1.0 Re_p > 1.0 R e p > 1.0 . For large particles ( d p > 1 mm d_p > 1\text{ mm} d p > 1 mm ), the settling regime shifts to Newton's law ( C D ≈ 0.44 C_D \approx 0.44 C D ≈ 0.44 ), where u t ∝ d p u_t \propto \sqrt{d_p} u t ∝ d p rather than d p 2 d_p^2 d p 2 .