Study guide
13.2 Temperature Dependence and the Arrhenius Equation
PE Chemical Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the PE Chemical Exam How to Use This Guide and the NCEES Handbook
2 Chapter 1: Material Balances & Flowsheet Calculations
1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations
3 Chapter 2: Energy Balances & Thermochemistry
2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances
4 Chapter 3: Fluid Statics & Incompressible Pipe Flow
3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations
5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow
4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up
6 Chapter 5: Thermodynamic Laws & Fundamental Relations
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations
7 Chapter 6: Real Gases & Equations of State
6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions
8 Chapter 7: Phase & Chemical Reaction Equilibria
7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
9 Chapter 8: Heat Transfer Mechanisms & Conduction
8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange
10 Chapter 9: Heat Exchanger Design & Phase Change
9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances
11 Chapter 10: Mass Transfer Fundamentals & Diffusion
10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)
12 Chapter 11: Distillation Operations
11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components
13 Chapter 12: Rate-Controlled & Equilibrium Separations
12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations
14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors
13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations
15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis
14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models
16 Chapter 15: Physical & Transport Properties of Fluids
15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles
17 Chapter 16: Materials of Construction & Corrosion
16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention
18 Chapter 17: Process Safety & Pressure Relief Systems
17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment
19 Chapter 18: Process Control & Engineering Economics
18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems
20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance
19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation
21 Chapter 20: Plant Operation, Reliability & Continuous Improvement
20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting
13.2 Temperature Dependence and the Arrhenius Equation
Key Takeaways Explain This Topic AI
The Arrhenius equation k(T) = A * exp(-E_a / (R*T)) dictates that reaction rate constants increase exponentially with absolute temperature; on an Arrhenius plot of ln(k) versus 1/T, the slope is strictly -E_a / R and the y-intercept is ln(A).
Temperature must always be expressed in absolute thermodynamic units (Kelvin or Rankine); using Celsius or Fahrenheit produces catastrophic calculation errors in exponential rate equations.
The universal rule of thumb—that reaction rates approximately double for every 10 K (or 10 °C) rise—strictly holds only for moderate activation energies (E_a approx 50-55 kJ/mol) near ambient temperature (300 K).
Reactions with high activation energies (E_a > 100-150 kJ/mol) exhibit extreme temperature sensitivity, whereas catalytic reactions with low activation energies (E_a < 30-40 kJ/mol) or mass-transfer-limited reactions show mild temperature dependence.
For reversible reactions, the standard heat of reaction is Delta_H_rxn = E_a,forward - E_a,reverse; in exothermic reactions (Delta_H_rxn < 0), higher temperatures accelerate kinetics but diminish equilibrium conversion (X_eq), dictating a descending temperature profile along the reactor.
Last updated: September 2026
13.2 Temperature Dependence and the Arrhenius Equation
Temperature is the single most powerful operating variable available to the chemical engineer for controlling reaction rates and reactor performance. While fluid concentrations vary linearly or quadratically in reactor balances, the reaction rate constant k k k varies exponentially with temperature. An increase of just 20 ∘ C 20^\circ\text{C} 2 0 ∘ C to 30 ∘ C 30^\circ\text{C} 3 0 ∘ C can increase reaction rates by a factor of 4 to 10, dramatically reducing the required reactor volume or, if uncontrolled, leading to dangerous thermal runaways.
On the NCEES PE Chemical Exam , problems require evaluating activation energy from multi-temperature experimental data, scaling rate constants across operating conditions, and balancing kinetic speed against thermodynamic equilibrium limitations in reversible reactions.
1. The Arrhenius Equation and Activation Energy
In 1889, Svante Arrhenius proposed the empirical relationship governing the temperature dependence of the reaction rate constant k k k : k ( T ) = A exp ( − E a R T ) k(T) = A \exp\left( -\frac{E_a}{R T} \right) k ( T ) = A exp ( − RT E a )
Where:
k ( T ) k(T) k ( T ) = reaction rate constant at absolute temperature T T T .
A A A = pre-exponential factor (also known as the frequency factor ), possessing the exact same dimensional units as k k k .
E a E_a E a = activation energy of the reaction ( J/mol \text{J/mol} J/mol , kJ/mol \text{kJ/mol} kJ/mol , cal/mol \text{cal/mol} cal/mol , or Btu/lbmol \text{Btu/lbmol} Btu/lbmol ).
R R R = universal gas constant:
R = 8.31446 J / ( mol ⋅ K ) = 8.31446 × 10 − 3 kJ / ( mol ⋅ K ) R = 8.31446\text{ J}/(\text{mol}\cdot\text{K}) = 8.31446\times 10^{-3}\text{ kJ}/(\text{mol}\cdot\text{K}) R = 8.31446 J / ( mol ⋅ K ) = 8.31446 × 1 0 − 3 kJ / ( mol ⋅ K )
R = 1.9872 cal / ( mol ⋅ K ) = 1.9872 Btu / ( lbmol ⋅ ∘ R ) R = 1.9872\text{ cal}/(\text{mol}\cdot\text{K}) = 1.9872\text{ Btu}/(\text{lbmol}\cdot^\circ\text{R}) R = 1.9872 cal / ( mol ⋅ K ) = 1.9872 Btu / ( lbmol ⋅ ∘ R )
R = 8.31446 × 10 − 5 m 3 ⋅ bar / ( mol ⋅ K ) = 0.082057 L ⋅ atm / ( mol ⋅ K ) R = 8.31446\times 10^{-5}\text{ m}^3\cdot\text{bar}/(\text{mol}\cdot\text{K}) = 0.082057\text{ L}\cdot\text{atm}/(\text{mol}\cdot\text{K}) R = 8.31446 × 1 0 − 5 m 3 ⋅ bar / ( mol ⋅ K ) = 0.082057 L ⋅ atm / ( mol ⋅ K )
T T T = absolute thermodynamic temperature ( K \text{K} K or ∘ R ^\circ\text{R} ∘ R ).
The Linearized Arrhenius Form
Taking the natural logarithm of both sides transforms the exponential relationship into a linear equation ( y = m x + b y = mx + b y = m x + b ): ln ( k ) = ln ( A ) − E a R ( 1 T ) \ln(k) = \ln(A) - \frac{E_a}{R} \left( \frac{1}{T} \right) ln ( k ) = ln ( A ) − R E a ( T 1 )
When experimental ln ( k ) \ln(k) ln ( k ) data are plotted against reciprocal absolute temperature ( 1 / T ) (1/T) ( 1/ T ) :
The data form a straight line with slope m = − E a R m = -\frac{E_a}{R} m = − R E a .
The activation energy is directly obtained from the slope: E a = − R ⋅ m E_a = -R \cdot m E a = − R ⋅ m .
The vertical intercept at 1 / T = 0 1/T = 0 1/ T = 0 corresponds to ln ( A ) \ln(A) ln ( A ) . Arrhenius Plot: ln(k) versus (1/T)
- ln(k)
- ^
- | * (High T, Low 1/T)
- | \
- | \ Slope = -E_a / R
- | \
- | \
- | * (Low T, High 1/T)
- +-----------------------------------> (1/T) [1/K]
- Two-Point Temperature Ratio Form
In most PE exam calculations, rate constants are known or specified at two discrete temperatures, T 1 T_1 T 1 and T 2 T_2 T 2 . Subtracting the linearized equations eliminates the frequency factor A A A : ln ( k 2 k 1 ) = − E a R ( 1 T 2 − 1 T 1 ) = E a R ( T 2 − T 1 T 1 T 2 ) \ln\left( \frac{k_2}{k_1} \right) = -\frac{E_a}{R} \left( \frac{1}{T_2} - \frac{1}{T_1} \right) = \frac{E_a}{R} \left( \frac{T_2 - T_1}{T_1 T_2} \right) ln ( k 1 k 2 ) = − R E a ( T 2 1 − T 1 1 ) = R E a ( T 1 T 2 T 2 − T 1 )
Solving explicitly for k 2 k_2 k 2 at temperature T 2 T_2 T 2 given k 1 k_1 k 1 at T 1 T_1 T 1 : k 2 = k 1 exp [ E a R ( T 2 − T 1 T 1 T 2 ) ] k_2 = k_1 \exp\left[ \frac{E_a}{R} \left( \frac{T_2 - T_1}{T_1 T_2} \right) \right] k 2 = k 1 exp [ R E a ( T 1 T 2 T 2 − T 1 ) ]
Caution
Inconsistent Units of R R R and E a E_a E a :
The most prevalent numerical pitfall on the PE exam is mixing units: combining E a E_a E a in kJ/mol \text{kJ/mol} kJ/mol with R = 8.314 J / ( mol ⋅ K ) R = 8.314\text{ J}/(\text{mol}\cdot\text{K}) R = 8.314 J / ( mol ⋅ K ) without converting E a E_a E a to J/mol \text{J/mol} J/mol (or dividing R R R by 1,000). A factor of 1 , 000 1,000 1 , 000 error in an exponential exponent generates answers that differ by billions of orders of magnitude.
2. Theoretical Foundations: Collision Theory vs. Transition State Theory
While Arrhenius formulated his law empirically, modern chemical physics explains the temperature dependence through two complementary microscale theories.
Collision Theory of Gas Reactions
Collision theory models reacting molecules as hard spheres. For a reaction to take place:
Molecules must physically collide.
The relative kinetic energy along the line of centers must exceed a threshold energy barrier, E c E_c E c .
Colliding molecules must be oriented favorably (quantified by a steric factor, P P P ).
From kinetic gas theory, the collision frequency between molecules increases proportionally to the mean molecular speed, which varies as T 1 / 2 T^{1/2} T 1/2 . The fraction of collisions possessing energy exceeding E c E_c E c is given by the Boltzmann distribution exp ( − E c / R T ) \exp(-E_c / R T) exp ( − E c / RT ) . Thus, collision theory yields: k ( T ) = A ′ T 1 / 2 e x p ( − E c R T ) k(T) = A' T^{1/2} \ exp\left( -\frac{E_c}{R T} \right) k ( T ) = A ′ T 1/2 e x p ( − RT E c )
Transition State Theory (Eyring Equation)
Transition state theory (activated complex theory) assumes that reactants are in quasi-thermodynamic equilibrium with a high-energy, unstable intermediate known as the activated complex or transition state ( [ A B ] ‡ [AB]^\ddagger [ A B ] ‡ ): A + B ⇌ [ A B ] ‡ ⟶ Products A + B \rightleftharpoons [AB]^\ddagger \longrightarrow \text{Products} A + B ⇌ [ A B ] ‡ ⟶ Products
The rate constant derived from statistical mechanics and transition-state thermodynamics is given by the Eyring-Polanyi equation : k ( T ) = k B T h exp ( Δ S ‡ R ) exp ( − Δ H ‡ R T ) k(T) = \frac{k_B T}{h} \exp\left( \frac{\Delta S^\ddagger}{R} \right) \exp\left( -\frac{\Delta H^\ddagger}{R T} \right) k ( T ) = h k B T exp ( R Δ S ‡ ) exp ( − RT Δ H ‡ )
Where:
k B k_B k B = Boltzmann constant ( 1.38065 × 10 − 23 J/K 1.38065\times 10^{-23}\text{ J/K} 1.38065 × 1 0 − 23 J/K ).
h h h = Planck constant ( 6.62607 × 10 − 34 J ⋅ s 6.62607\times 10^{-34}\text{ J}\cdot\text{s} 6.62607 × 1 0 − 34 J ⋅ s ).
Δ S ‡ \Delta S^\ddagger Δ S ‡ = standard entropy of activation (related to the frequency factor A A A ).
Δ H ‡ \Delta H^\ddagger Δ H ‡ = standard enthalpy of activation (related to activation energy by E a = Δ H ‡ + R T E_a = \Delta H^\ddagger + R T E a = Δ H ‡ + RT for liquid solutions, or E a = Δ H ‡ + 2 R T E_a = \Delta H^\ddagger + 2 R T E a = Δ H ‡ + 2 RT for bimolecular gas reactions).
Why the Simple Arrhenius Equation Holds in Practice
Notice that collision theory predicts k ∝ T 1 / 2 exp ( − E / R T ) k \propto T^{1/2} \exp(-E/RT) k ∝ T 1/2 exp ( − E / RT ) , while transition state theory predicts k ∝ T 1 exp ( − E / R T ) k \propto T^1 \exp(-E/RT) k ∝ T 1 exp ( − E / RT ) . However, over any practical industrial temperature interval (e.g., 300 K 300\text{ K} 300 K to 400 K 400\text{ K} 400 K , a 33 % 33\% 33% change in T T T ):
The pre-exponential temperature factor T 1 T^1 T 1 increases by only a factor of 400 / 300 = 1.33 400/300 = 1.33 400/300 = 1.33 .
The exponential Boltzmann factor exp ( − E a / R T ) \exp(-E_a / RT) exp ( − E a / RT ) for E a = 80 kJ/mol E_a = 80\text{ kJ/mol} E a = 80 kJ/mol increases by a factor of exp [ ( 80,000 / 8.314 ) ( 1 / 300 − 1 / 400 ) ] = exp ( 8.018 ) = 3 , 036 \exp[(80{,}000/8.314)(1/300 - 1/400)] = \exp(8.018) = 3,\!036 exp [( 80 , 000/8.314 ) ( 1/300 − 1/400 )] = exp ( 8.018 ) = 3 , 036 !
Because the exponential term varies thousands of times faster than the polynomial temperature coefficient, the temperature dependence of A A A is negligible. The simple Arrhenius equation with a constant pre-exponential factor A A A remains extraordinarily accurate across engineering temperature ranges.
3. Temperature Sensitivity, Activation Energy Magnitude, and Rules of Thumb
The magnitude of the activation energy E a E_a E a dictates how aggressively a reaction responds to changes in temperature.
Mathematical Sensitivity (Logarithmic Derivative)
Differentiating the Arrhenius equation with respect to temperature: d ln ( k ) d T = 1 k d k d T = E a R T 2 \frac{d\ln(k)}{dT} = \frac{1}{k} \frac{dk}{dT} = \frac{E_a}{R T^2} d T d ln ( k ) = k 1 d T d k = R T 2 E a
This differential sensitivity shows that:
Sensitivity increases with E a E_a E a : Reactions with high activation barriers experience vastly larger percentage changes in rate per degree temperature rise than reactions with low activation barriers.
Sensitivity decreases with T T T : The sensitivity varies inversely with T 2 T^2 T 2 . Raising temperature from 300 K 300\text{ K} 300 K to 310 K 310\text{ K} 310 K causes a substantially larger fractional rate increase than raising temperature from 800 K 800\text{ K} 800 K to 810 K 810\text{ K} 810 K .
The "Doubling Every 10 K" Rule of Thumb
A ubiquitous industrial rule of thumb states that homogeneous reaction rates roughly double for every 10 ∘ C 10^\circ\text{C} 1 0 ∘ C ( 10 K 10\text{ K} 10 K ) increase in temperature. We can rigorously verify the physical boundaries under which this rule applies: k ( T + 10 ) k ( T ) = 2.00 ⟹ ln ( 2.00 ) = 0.69315 = E a R ( 10 T ( T + 10 ) ) \frac{k(T + 10)}{k(T)} = 2.00 \implies \ln(2.00) = 0.69315 = \frac{E_a}{R} \left( \frac{10}{T (T + 10)} \right) k ( T ) k ( T + 10 ) = 2.00 ⟹ ln ( 2.00 ) = 0.69315 = R E a ( T ( T + 10 ) 10 )
Solving for E a E_a E a at ambient temperature ( T = 300 K T = 300\text{ K} T = 300 K , T + 10 = 310 K T + 10 = 310\text{ K} T + 10 = 310 K ): E a = 0.69315 ⋅ ( 8.31446 J / ( mol ⋅ K ) ) ⋅ ( 300 K ⋅ 310 K ) 10 K = 0.69315 ⋅ 8.31446 ⋅ 93,000 10 = 53,595 J/mol ≈ 53.6 kJ/mol E_a = \frac{0.69315 \cdot (8.31446\text{ J}/(\text{mol}\cdot\text{K})) \cdot (300\text{ K} \cdot 310\text{ K})}{10\text{ K}} = \frac{0.69315 \cdot 8.31446 \cdot 93{,}000}{10} = \mathbf{53{,}595\text{ J/mol}} \approx 53.6\text{ kJ/mol} E a = 10 K 0.69315 ⋅ ( 8.31446 J / ( mol ⋅ K )) ⋅ ( 300 K ⋅ 310 K ) = 10 0.69315 ⋅ 8.31446 ⋅ 93 , 000 = 53 , 595 J/mol ≈ 53.6 kJ/mol
Note
Validity of the 10 K Doubling Rule:
The rate doubles every 10 K 10\text{ K} 10 K only if E a ≈ 53 kJ/mol E_a \approx 53\text{ kJ/mol} E a ≈ 53 kJ/mol ( 12.8 kcal/mol 12.8\text{ kcal/mol} 12.8 kcal/mol ) near room temperature ( 300 K 300\text{ K} 300 K ). If E a = 150 kJ/mol E_a = 150\text{ kJ/mol} E a = 150 kJ/mol , a 10 K 10\text{ K} 10 K rise increases the rate by a factor of nearly 7.0 7.0 7.0 ! Never blindly apply the "doubles every 10 degrees" rule on the PE exam without checking the stated activation energy.
Regimes of Activation Energy in Chemical Engineering
Mass Transfer Limited / Diffusion Controlled ( E a < 20 kJ/mol E_a < 20\text{ kJ/mol} E a < 20 kJ/mol ): Physical diffusion in liquids has an activation energy of 10 − 20 kJ/mol 10-20\text{ kJ/mol} 10 − 20 kJ/mol . If an experimental catalytic reaction exhibits an apparent E a E_a E a below 20 kJ/mol 20\text{ kJ/mol} 20 kJ/mol , the process is almost certainly limited by external film or pore diffusion, not intrinsic chemical kinetics.
Typical Catalytic Reactions ( E a ≈ 40 − 80 kJ/mol E_a \approx 40 - 80\text{ kJ/mol} E a ≈ 40 − 80 kJ/mol ): Catalysts provide alternative reaction pathways with lower activation barriers.
Homogeneous Non-Catalytic Reactions ( E a ≈ 80 − 250 kJ/mol E_a \approx 80 - 250\text{ kJ/mol} E a ≈ 80 − 250 kJ/mol ): Bond-breaking thermal reactions (pyrolysis, combustion, gas-phase chlorination) possess high activation barriers and exhibit extreme temperature sensitivity.
4. Reversible Reactions and the van 't Hoff Equation
For a reversible elementary reaction A ⇌ B A \rightleftharpoons B A ⇌ B , both the forward rate constant k f k_f k f and reverse rate constant k r k_r k r follow Arrhenius temperature dependence: k f = A f exp ( − E a , f R T ) , k r = A r exp ( − E a , r R T ) k_f = A_f \exp\left( -\frac{E_{a,f}}{R T} \right), \qquad k_r = A_r \exp\left( -\frac{E_{a,r}}{R T} \right) k f = A f exp ( − RT E a , f ) , k r = A r exp ( − RT E a , r )
The thermodynamic equilibrium constant is the ratio of rate constants: K c = k f k r = ( A f A r ) exp ( − E a , f − E a , r R T ) K_c = \frac{k_f}{k_r} = \left( \frac{A_f}{A_r} \right) \exp\left( -\frac{E_{a,f} - E_{a,r}}{R T} \right) K c = k r k f = ( A r A f ) exp ( − RT E a , f − E a , r )
Comparing this expression to classical thermodynamics ( K c ∝ exp ( − Δ H r x n ∘ / R T ) K_c \propto \exp(-\Delta H_{rxn}^\circ / R T) K c ∝ exp ( − Δ H r x n ∘ / RT ) ) establishes that the standard enthalpy (heat) of reaction is the exact difference between forward and reverse activation energies: Δ H r x n ∘ = E a , f − E a , r \Delta H_{rxn}^\circ = E_{a,f} - E_{a,r} Δ H r x n ∘ = E a , f − E a , r Reaction Coordinate & Energy Profiles:
- Potential Energy Potential Energy
- ^ [Activated Complex] ^ [Activated Complex]
- | /\ | /\
- | E_a,f / \ E_a,r | E_a,f / \ E_a,r
- | / \ | / \
- | A / \ B | / \
- | --- --- | A / \ B
- | \__ _/ | --- ---
- | Delta_H < 0 | \_____/
- | (EXOTHERMIC) | Delta_H > 0 (ENDOTHERMIC)
- +---------------------> Coord +---------------------> Coord
- The van 't Hoff Equation
Differentiating ln ( K c ) \ln(K_c) ln ( K c ) with respect to temperature yields the van 't Hoff equation : d ln ( K c ) d T = Δ H r x n ∘ R T 2 \frac{d\ln(K_c)}{dT} = \frac{\Delta H_{rxn}^\circ}{R T^2} d T d ln ( K c ) = R T 2 Δ H r x n ∘
Integrated between temperatures T 1 T_1 T 1 and T 2 T_2 T 2 : ln ( K c 2 K c 1 ) = − Δ H r x n ∘ R ( 1 T 2 − 1 T 1 ) = Δ H r x n ∘ R ( T 2 − T 1 T 1 T 2 ) \ln\left( \frac{K_{c2}}{K_{c1}} \right) = -\frac{\Delta H_{rxn}^\circ}{R} \left( \frac{1}{T_2} - \frac{1}{T_1} \right) = \frac{\Delta H_{rxn}^\circ}{R} \left( \frac{T_2 - T_1}{T_1 T_2} \right) ln ( K c 1 K c 2 ) = − R Δ H r x n ∘ ( T 2 1 − T 1 1 ) = R Δ H r x n ∘ ( T 1 T 2 T 2 − T 1 )
Thermodynamic Consequences for Reactor Operation
Endothermic Reactions ( Δ H r x n ∘ > 0 ⟹ E a , f > E a , r \Delta H_{rxn}^\circ > 0 \implies E_{a,f} > E_{a,r} Δ H r x n ∘ > 0 ⟹ E a , f > E a , r ):
As temperature increases, K c K_c K c increases.
Both the forward rate constant k f k_f k f and the maximum attainable equilibrium conversion X e q X_{eq} X e q increase.
Design strategy: Run endothermic reactors at the highest allowable metallurgical or materials temperature limit to maximize both speed and yield.
Exothermic Reactions ( Δ H r x n ∘ < 0 ⟹ E a , f < E a , r \Delta H_{rxn}^\circ < 0 \implies E_{a,f} < E_{a,r} Δ H r x n ∘ < 0 ⟹ E a , f < E a , r ):
As temperature increases, the reverse rate constant k r k_r k r grows faster than k f k_f k f because E a , r > E a , f E_{a,r} > E_{a,f} E a , r > E a , f .
Consequently, K c K_c K c decreases as temperature rises, causing equilibrium conversion X e q X_{eq} X e q to fall dramatically.
While higher temperatures increase the initial kinetic rate, they severely depress the maximum thermodynamic conversion.
5. Temperature Optimization in Exothermic Reversible Systems
Because of the conflict between kinetics (favored at high T T T ) and chemical equilibrium (favored at low T T T ), reversible exothermic reactions (such as ammonia synthesis, sulfur dioxide oxidation, or methanol synthesis) exhibit an optimal temperature for any given conversion. Reversible Exothermic Reaction Rate Trajectory:
- Conversion (X)
- ^
- 1.0 | / Equilibrium Curve X_eq(T)
- | / (Thermodynamic Limit: Decreases with T)
- | /
- | +------------/ <-- Locus of Maximum Rates
- | | Optimum /
- | | Operating/
- | | Path /
- | | /
- | | /
- 0.0 +---+--------------------------------> Temperature (T)
- T_exit T_inlet
To maximize the reaction rate at a specific conversion X X X , setting ( ∂ ( − r A ) ∂ T ) X = 0 \left( \frac{\partial (-r_A)}{\partial T} \right)_X = 0 ( ∂ T ∂ ( − r A ) ) X = 0 yields the locus of maximum reaction rates : T o p t = E a , r − E a , f R ln [ A r A f E a , r E a , f ( X 1 − X ) ] = − Δ H r x n ∘ R ln [ A r E a , r A f E a , f ( X 1 − X ) ] T_{opt} = \frac{E_{a,r} - E_{a,f}}{R \ln\left[ \frac{A_r}{A_f} \frac{E_{a,r}}{E_{a,f}} \left(\frac{X}{1-X}\right) \right]} = \frac{-\Delta H_{rxn}^\circ}{R \ln\left[ \frac{A_r E_{a,r}}{A_f E_{a,f}} \left(\frac{X}{1-X}\right) \right]} T o pt = R ln [ A f A r E a , f E a , r ( 1 − X X ) ] E a , r − E a , f = R ln [ A f E a , f A r E a , r ( 1 − X X ) ] − Δ H r x n ∘
Practical Engineering Implications:
At the reactor inlet ( X ≈ 0 X \approx 0 X ≈ 0 ), operate at high temperature to ignite the reaction and achieve rapid conversion.
As conversion increases, progressively cool the reacting mixture along the reactor length (using interstage cooling, heat exchangers, or cold-shot gas injection) to track the optimal temperature locus and avoid thermodynamic equilibrium pinching.
6. Summary Comparison Table: Temperature Dependence & Thermodynamics
Parameter / Feature Endothermic Reaction ( Δ H r x n ∘ > 0 \Delta H_{rxn}^\circ > 0 Δ H r x n ∘ > 0 ) Exothermic Reaction ( Δ H r x n ∘ < 0 \Delta H_{rxn}^\circ < 0 Δ H r x n ∘ < 0 )
Relative Activation Energies E a , f > E a , r E_{a,f} > E_{a,r} E a , f > E a , r E a , f < E a , r E_{a,f} < E_{a,r} E a , f < E a , r
Effect of Increasing T T T on k f k_f k f Increases exponentially Increases exponentially
Effect of Increasing T T T on k r k_r k r Increases moderately Increases aggressively ( E a , r > E a , f E_{a,r} > E_{a,f} E a , r > E a , f )
Effect of Increasing T T T on K c K_c K c Increases ( d ln K / d T > 0 d\ln K/dT > 0 d ln K / d T > 0 ) Decreases ( d ln K / d T < 0 d\ln K/dT < 0 d ln K / d T < 0 )
Equilibrium Conversion ( X e q X_{eq} X e q ) Increases with T T T Decreases with T T T
Optimal Reactor Temperature Profile Maintain highest possible T T T along entire reactor High T T T at inlet, descending to low T T T at outlet
Thermal Runaway Risk Inherently self-quenching (safe) High risk of runaway ( + Q g e n +Q_{gen} + Q g e n accelerates rate)
- 7. Step-by-Step Worked Numerical Example: Multi-Temperature Kinetic Analysis & Reactor Scaling
- Problem Statement
A pharmaceutical intermediate decomposes via an elementary, irreversible first-order reaction: A ⟶ Products A \longrightarrow \text{Products} A ⟶ Products
Kinetic measurements in an isothermal batch test unit determine the following rate constants:
At T 1 = 47.0 ∘ C T_1 = 47.0^\circ\text{C} T 1 = 47. 0 ∘ C ( 320.15 K 320.15\text{ K} 320.15 K ): k 1 = 0.0150 min − 1 k_1 = 0.0150\text{ min}^{-1} k 1 = 0.0150 min − 1
At T 2 = 87.0 ∘ C T_2 = 87.0^\circ\text{C} T 2 = 87. 0 ∘ C ( 360.15 K 360.15\text{ K} 360.15 K ): k 2 = 0.1850 min − 1 k_2 = 0.1850\text{ min}^{-1} k 2 = 0.1850 min − 1
Calculate:
The activation energy E a E_a E a in kJ/mol \text{kJ/mol} kJ/mol and cal/mol \text{cal/mol} cal/mol .
The pre-exponential frequency factor A A A in min − 1 \text{min}^{-1} min − 1 and s − 1 \text{s}^{-1} s − 1 .
The predicted rate constant k 3 k_3 k 3 at a target operating temperature of T 3 = 127.0 ∘ C T_3 = 127.0^\circ\text{C} T 3 = 127. 0 ∘ C ( 400.15 K 400.15\text{ K} 400.15 K ).
The factor by which the required reactor volume decreases if the operating temperature is increased from 47.0 ∘ C 47.0^\circ\text{C} 47. 0 ∘ C to 127.0 ∘ C 127.0^\circ\text{C} 127. 0 ∘ C for a continuous first-order reactor achieving 90 % 90\% 90% conversion.
Step 1: Calculate Activation Energy ( E a E_a E a )
Convert temperatures to absolute thermodynamic scale:
- T 1 = 47.0 + 273.15 = 320.15 K T_1 = 47.0 + 273.15 = 320.15\text{ K} T 1 = 47.0 + 273.15 = 320.15 K
- T 2 = 87.0 + 273.15 = 360.15 K T_2 = 87.0 + 273.15 = 360.15\text{ K} T 2 = 87.0 + 273.15 = 360.15 K
Evaluate the natural logarithm of the rate constant ratio: ln ( k 2 k 1 ) = ln ( 0.1850 0.0150 ) = ln ( 12.3333 ) = 2.51231 \ln\left( \frac{k_2}{k_1} \right) = \ln\left( \frac{0.1850}{0.0150} \right) = \ln(12.3333) = 2.51231 ln ( k 1 k 2 ) = ln ( 0.0150 0.1850 ) = ln ( 12.3333 ) = 2.51231
Evaluate the reciprocal temperature difference: 1 T 1 − 1 T 2 = 1 320.15 − 1 360.15 = 0.00312354 − 0.00277662 = 0.00034692 K − 1 \frac{1}{T_1} - \frac{1}{T_2} = \frac{1}{320.15} - \frac{1}{360.15} = 0.00312354 - 0.00277662 = 0.00034692\text{ K}^{-1} T 1 1 − T 2 1 = 320.15 1 − 360.15 1 = 0.00312354 − 0.00277662 = 0.00034692 K − 1
Applying the two-point Arrhenius equation: E a R = ln ( k 2 / k 1 ) 1 T 1 − 1 T 2 = 2.51231 0.00034692 K − 1 = 7 , 241.75 K \frac{E_a}{R} = \frac{\ln(k_2 / k_1)}{\frac{1}{T_1} - \frac{1}{T_2}} = \frac{2.51231}{0.00034692\text{ K}^{-1}} = 7,\!241.75\text{ K} R E a = T 1 1 − T 2 1 ln ( k 2 / k 1 ) = 0.00034692 K − 1 2.51231 = 7 , 241.75 K
Now multiply by the gas constant R R R : E a = 7 , 241.75 K × 8.31446 × 10 − 3 kJ / ( mol ⋅ K ) = 60.21 kJ/mol ( 60 , 210 J/mol ) E_a = 7,\!241.75\text{ K} \times 8.31446\times 10^{-3}\text{ kJ}/(\text{mol}\cdot\text{K}) = \mathbf{60.21\text{ kJ/mol}} \quad (60,\!210\text{ J/mol}) E a = 7 , 241.75 K × 8.31446 × 1 0 − 3 kJ / ( mol ⋅ K ) = 60.21 kJ/mol ( 60 , 210 J/mol )
In calorie units ( R = 1.9872 cal / ( mol ⋅ K ) R = 1.9872\text{ cal}/(\text{mol}\cdot\text{K}) R = 1.9872 cal / ( mol ⋅ K ) ): E a = 7 , 241.75 K × 1.9872 cal / ( mol ⋅ K ) = 14 , 391 cal/mol ( 14.39 kcal/mol ) E_a = 7,\!241.75\text{ K} \times 1.9872\text{ cal}/(\text{mol}\cdot\text{K}) = \mathbf{14,\!391\text{ cal/mol}} \quad (14.39\text{ kcal/mol}) E a = 7 , 241.75 K × 1.9872 cal / ( mol ⋅ K ) = 14 , 391 cal/mol ( 14.39 kcal/mol )
Step 2: Calculate the Pre-Exponential Frequency Factor ( A A A )
From the Arrhenius equation at T 1 T_1 T 1 : k 1 = A exp ( − E a R T 1 ) ⟹ A = k 1 exp ( E a R T 1 ) k_1 = A \exp\left( -\frac{E_a}{R T_1} \right) \implies A = k_1 \exp\left( \frac{E_a}{R T_1} \right) k 1 = A exp ( − R T 1 E a ) ⟹ A = k 1 exp ( R T 1 E a ) E a R T 1 = 7 , 241.75 K 320.15 K = 22.6198 \frac{E_a}{R T_1} = \frac{7,\!241.75\text{ K}}{320.15\text{ K}} = 22.6198 R T 1 E a = 320.15 K 7 , 241.75 K = 22.6198 exp ( 22.6198 ) = 6.6629 × 10 9 \exp(22.6198) = 6.6629\times 10^9 exp ( 22.6198 ) = 6.6629 × 1 0 9 A = 0.0150 min − 1 × 6.6629 × 10 9 = 9.994 × 10 7 min − 1 A = 0.0150\text{ min}^{-1} \times 6.6629\times 10^9 = \mathbf{9.994\times 10^7\text{ min}^{-1}} A = 0.0150 min − 1 × 6.6629 × 1 0 9 = 9.994 × 1 0 7 min − 1
Converting to reciprocal seconds: A = 9.994 × 10 7 min − 1 60 s/min = 1.666 × 10 6 s − 1 A = \frac{9.994\times 10^7\text{ min}^{-1}}{60\text{ s/min}} = \mathbf{1.666\times 10^6\text{ s}^{-1}} A = 60 s/min 9.994 × 1 0 7 min − 1 = 1.666 × 1 0 6 s − 1
Step 3: Predict Rate Constant at 127.0 ∘ C 127.0^\circ\text{C} 127. 0 ∘ C ( T 3 = 400.15 K T_3 = 400.15\text{ K} T 3 = 400.15 K )
Using the two-point form between T 1 T_1 T 1 and T 3 T_3 T 3 : 1 T 1 − 1 T 3 = 1 320.15 − 1 400.15 = 0.00312354 − 0.00249906 = 0.00062448 K − 1 \frac{1}{T_1} - \frac{1}{T_3} = \frac{1}{320.15} - \frac{1}{400.15} = 0.00312354 - 0.00249906 = 0.00062448\text{ K}^{-1} T 1 1 − T 3 1 = 320.15 1 − 400.15 1 = 0.00312354 − 0.00249906 = 0.00062448 K − 1 ln ( k 3 k 1 ) = E a R ( 1 T 1 − 1 T 3 ) = 7 , 241.75 K × 0.00062448 K − 1 = 4.5223 \ln\left( \frac{k_3}{k_1} \right) = \frac{E_a}{R} \left( \frac{1}{T_1} - \frac{1}{T_3} \right) = 7,\!241.75\text{ K} \times 0.00062448\text{ K}^{-1} = 4.5223 ln ( k 1 k 3 ) = R E a ( T 1 1 − T 3 1 ) = 7 , 241.75 K × 0.00062448 K − 1 = 4.5223 k 3 k 1 = exp ( 4.5223 ) = 92.047 \frac{k_3}{k_1} = \exp(4.5223) = 92.047 k 1 k 3 = exp ( 4.5223 ) = 92.047 k 3 = 0.0150 min − 1 × 92.047 = 1.381 min − 1 ( 0.0230 s − 1 ) k_3 = 0.0150\text{ min}^{-1} \times 92.047 = \mathbf{1.381\text{ min}^{-1}} \quad (0.0230\text{ s}^{-1}) k 3 = 0.0150 min − 1 × 92.047 = 1.381 min − 1 ( 0.0230 s − 1 )
Notice that increasing the temperature by 80 ∘ C 80^\circ\text{C} 8 0 ∘ C (from 47 ∘ C 47^\circ\text{C} 4 7 ∘ C to 127 ∘ C 127^\circ\text{C} 12 7 ∘ C ) accelerates the reaction rate by a factor of 92.0 92.0 92.0 !
Step 4: Volume Reduction Factor for Reactor Sizing
For any ideal continuous isothermal reactor (CSTR or PFR) executing a first-order irreversible reaction to a fixed conversion X X X : V ∝ 1 k V \propto \frac{1}{k} V ∝ k 1
Therefore, the required reactor volume at 47.0 ∘ C 47.0^\circ\text{C} 47. 0 ∘ C relative to 127.0 ∘ C 127.0^\circ\text{C} 127. 0 ∘ C is: V ( 47 ∘ C ) V ( 127 ∘ C ) = k 3 k 1 = 92.05 \frac{V(47^\circ\text{C})}{V(127^\circ\text{C})} = \frac{k_3}{k_1} = 92.05 V ( 12 7 ∘ C ) V ( 4 7 ∘ C ) = k 1 k 3 = 92.05
Operating at 127 ∘ C 127^\circ\text{C} 12 7 ∘ C reduces the required reactor volume by 98.9 % 98.9\% 98.9% ( 1 − 1 / 92.05 = 0.9891 1 - 1/92.05 = 0.9891 1 − 1/92.05 = 0.9891 ), enabling an engineer to replace a 9 , 200 L 9,\!200\text{ L} 9 , 200 L vessel with a compact 100 L 100\text{ L} 100 L vessel.
- 8. Critical PE Exam Traps & Pitfalls
- Trap 1: Failing to Use Absolute Temperature Scale
Inserting temperatures in Celsius (e.g., evaluating 87 − 47 47 × 87 \frac{87 - 47}{47 \times 87} 47 × 87 87 − 47 ) produces a completely nonsensical result. Always convert to Kelvin ( + 273.15 +273.15 + 273.15 ) or Rankine ( + 459.67 +459.67 + 459.67 ) before touching the calculator.
Trap 2: Mismatching Gas Constant Units with Activation Energy
If E a E_a E a is specified as 75.0 kJ/mol 75.0\text{ kJ/mol} 75.0 kJ/mol , you must write E a / R = 75,000 / 8.314 = 9 , 020.9 K E_a / R = 75{,}000 / 8.314 = 9,\!020.9\text{ K} E a / R = 75 , 000/8.314 = 9 , 020.9 K or 75.0 / 0.008314 = 9 , 020.9 K 75.0 / 0.008314 = 9,\!020.9\text{ K} 75.0/0.008314 = 9 , 020.9 K . Using 75.0 / 8.314 = 9.02 K 75.0 / 8.314 = 9.02\text{ K} 75.0/8.314 = 9.02 K is an instant, catastrophic factor-of-1,000 error.
Trap 3: Forgetting the Temperature Effect on Equilibrium in Exothermic Reactions
When a problem asks to increase conversion in an exothermic reversible reactor, raising temperature increases the rate initially, but if the reactor is near equilibrium, raising temperature will decrease conversion! The correct answer on the PE exam is often to install interstage cooling or operate at a lower temperature.
Trap 4: Incorrect Sign in Two-Point Arrhenius Form
Write the two-point relation with careful attention to indices: ln ( k 2 / k 1 ) = − E a R ( 1 T 2 − 1 T 1 ) = + E a R ( 1 T 1 − 1 T 2 ) \ln(k_2 / k_1) = -\frac{E_a}{R}\left(\frac{1}{T_2} - \frac{1}{T_1}\right) = +\frac{E_a}{R}\left(\frac{1}{T_1} - \frac{1}{T_2}\right) ln ( k 2 / k 1 ) = − R E a ( T 2 1 − T 1 1 ) = + R E a ( T 1 1 − T 2 1 ) Since T 2 > T 1 T_2 > T_1 T 2 > T 1 , 1 / T 1 > 1 / T 2 1/T_1 > 1/T_2 1/ T 1 > 1/ T 2 , so ( 1 / T 1 − 1 / T 2 ) (1/T_1 - 1/T_2) ( 1/ T 1 − 1/ T 2 ) is positive, ensuring k 2 > k 1 k_2 > k_1 k 2 > k 1 . Always sanity check that higher temperatures produce larger rate constants!