Study guide
13.1 Reaction Rates, Rate Laws, and Order of Reaction
PE Chemical Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the PE Chemical Exam How to Use This Guide and the NCEES Handbook
2 Chapter 1: Material Balances & Flowsheet Calculations
1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations
3 Chapter 2: Energy Balances & Thermochemistry
2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances
4 Chapter 3: Fluid Statics & Incompressible Pipe Flow
3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations
5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow
4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up
6 Chapter 5: Thermodynamic Laws & Fundamental Relations
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations
7 Chapter 6: Real Gases & Equations of State
6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions
8 Chapter 7: Phase & Chemical Reaction Equilibria
7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
9 Chapter 8: Heat Transfer Mechanisms & Conduction
8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange
10 Chapter 9: Heat Exchanger Design & Phase Change
9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances
11 Chapter 10: Mass Transfer Fundamentals & Diffusion
10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)
12 Chapter 11: Distillation Operations
11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components
13 Chapter 12: Rate-Controlled & Equilibrium Separations
12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations
14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors
13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations
15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis
14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models
16 Chapter 15: Physical & Transport Properties of Fluids
15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles
17 Chapter 16: Materials of Construction & Corrosion
16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention
18 Chapter 17: Process Safety & Pressure Relief Systems
17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment
19 Chapter 18: Process Control & Engineering Economics
18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems
20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance
19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation
21 Chapter 20: Plant Operation, Reliability & Continuous Improvement
20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting
13.1 Reaction Rates, Rate Laws, and Order of Reaction
Key Takeaways Explain This Topic AI
The intensive rate of reaction for species i is defined as r_i = (1/V)(dn_i/dt) = nu_i * r_rxn, linking relative rates of disappearance and formation through stoichiometric coefficients: -r_A / a = -r_B / b = r_C / c = r_D / d.
In power-law rate laws (-r_A = k * C_A^alpha * C_B^beta), the partial orders alpha and beta must be determined experimentally and do not equal stoichiometric coefficients unless the reaction is proven to be elementary.
The dimensional units of the kinetic rate constant k are strictly governed by overall reaction order n: [k] = (concentration)^(1-n) * (time)^(-1); only a first-order rate constant (s^(-1) or min^(-1)) is independent of concentration units.
Half-life signatures diagnostic of reaction order are t_1/2 = C_A0 / (2k) for zero order (proportional to C_A0), t_1/2 = ln(2) / k = 0.693 / k for first order (independent of C_A0), and t_1/2 = 1 / (k * C_A0) for second order (inversely proportional to C_A0).
For reversible reactions, net rate is the difference between forward and reverse rates (-r_A = k_f * C_A - k_r * C_B), which at thermodynamic equilibrium (-r_A = 0) collapses to the equilibrium constant definition K_c = k_f / k_r = C_B,eq / C_A,eq.
Last updated: September 2026
13.1 Reaction Rates, Rate Laws, and Order of Reaction
Chemical reaction engineering combines chemical kinetics with physical transport phenomena to design, size, and optimize chemical reactors. In the NCEES PE Chemical Reference Handbook , chemical kinetics forms the foundation of reactor design. Before sizing an isothermal or non-isothermal vessel, the chemical engineer must establish the correct mathematical rate law, identify the true reaction order, and understand the physical significance and units of the kinetic rate constant.
1. Stoichiometric Definitions of Reaction Rate
For a homogeneous chemical reaction occurring in a fluid volume V V V , the rate of reaction of species i i i ( r i r_i r i ) is an intensive property defined as the moles of species i i i formed (or consumed) per unit volume per unit time: r i = 1 V d n i d t r_i = \frac{1}{V} \frac{dn_i}{dt} r i = V 1 d t d n i
Where:
n i n_i n i = moles of species i i i in the reacting system ( mol \text{mol} mol or kmol \text{kmol} kmol ).
V V V = volume of the reacting fluid mixture ( L \text{L} L or m 3 \text{m}^3 m 3 ).
t t t = time ( s \text{s} s , min \text{min} min , or h \text{h} h ).
r i r_i r i = rate of formation of species i i i (positive for products, negative for reactants, with units of mol / ( L ⋅ s ) \text{mol}/(\text{L}\cdot\text{s}) mol / ( L ⋅ s ) or kmol / ( m 3 ⋅ h ) \text{kmol}/(\text{m}^3\cdot\text{h}) kmol / ( m 3 ⋅ h ) ).
By convention in chemical engineering, the rate of disappearance (or consumption) of a reactant A A A is written as a positive quantity: − r A = − 1 V d n A d t -r_A = -\frac{1}{V} \frac{dn_A}{dt} − r A = − V 1 d t d n A .
Stoichiometric Relative Rates
Consider the general chemical reaction: a A + b B ⟶ c C + d D a A + b B \longrightarrow c C + d D a A + b B ⟶ c C + d D
Using the generalized stoichiometric equation ∑ ν j A j = 0 \sum \nu_j A_j = 0 ∑ ν j A j = 0 , where stoichiometric coefficients ν j \nu_j ν j are negative for reactants ( ν A = − a , ν B = − b \nu_A = -a, \nu_B = -b ν A = − a , ν B = − b ) and positive for products ( ν C = + c , ν D = + d \nu_C = +c, \nu_D = +d ν C = + c , ν D = + d ), the single, species-independent rate of reaction r r x n r_{rxn} r r x n is: r r x n = r i ν i = − r A a = − r B b = r C c = r D d r_{rxn} = \frac{r_i}{\nu_i} = \frac{-r_A}{a} = \frac{-r_B}{b} = \frac{r_C}{c} = \frac{r_D}{d} r r x n = ν i r i = a − r A = b − r B = c r C = d r D
Consequently, the relative rates of consumption and formation are directly linked by stoichiometry: − r B = b a ( − r A ) , r C = c a ( − r A ) , r D = d a ( − r A ) -r_B = \frac{b}{a} (-r_A), \qquad r_C = \frac{c}{a} (-r_A), \qquad r_D = \frac{d}{a} (-r_A) − r B = a b ( − r A ) , r C = a c ( − r A ) , r D = a d ( − r A )
Important
Stoichiometric Rate Constants:
When a problem provides a rate law such as − r A = k A C A 2 -r_A = k_A C_A^2 − r A = k A C A 2 , the rate constant k A k_A k A is defined with respect to reactant A A A . If the rate of consumption of reactant B B B is asked for a reaction 2 A + B → C 2A + B \to C 2 A + B → C , then − r B = 1 2 ( − r A ) = 1 2 k A C A 2 = k B C A 2 -r_B = \frac{1}{2}(-r_A) = \frac{1}{2} k_A C_A^2 = k_B C_A^2 − r B = 2 1 ( − r A ) = 2 1 k A C A 2 = k B C A 2 . Therefore, k B = 1 2 k A k_B = \frac{1}{2} k_A k B = 2 1 k A . Forgetting this stoichiometric factor is a frequent source of lost points on the PE exam.
2. Power-Law Rate Expressions and Reaction Order
For many homogeneous reactions, the rate of consumption of reactant A A A can be parameterized by an empirical power-law rate law : − r A = k C A α C B β … C M γ -r_A = k C_A^\alpha C_B^\beta \dots C_M^\gamma − r A = k C A α C B β … C M γ
Where:
k k k = reaction rate constant (a strong function of temperature via the Arrhenius equation, but independent of reactant concentrations).
C i C_i C i = molar concentration of species i i i ( mol/L \text{mol/L} mol/L or kmol/m 3 \text{kmol/m}^3 kmol/m 3 ).
α , β , … , γ \alpha, \beta, \dots, \gamma α , β , … , γ = partial reaction orders with respect to components A , B , … , M A, B, \dots, M A , B , … , M .
n = α + β + ⋯ + γ n = \alpha + \beta + \dots + \gamma n = α + β + ⋯ + γ = overall reaction order .
Dimensional Units of the Kinetic Rate Constant ( k k k )
The units of the rate of reaction are always [ concentration ] ⋅ [ time ] − 1 [\text{concentration}] \cdot [\text{time}]^{-1} [ concentration ] ⋅ [ time ] − 1 . Equating dimensions across the power-law equation reveals how the units of k k k depend fundamentally on overall order n n n : [ − r A ] = [ k ] [ C ] n ⟹ [ k ] = [ concentration ] [ time ] ⋅ [ concentration ] n = [ concentration ] 1 − n ⋅ [ time ] − 1 [-r_A] = [k] [C]^n \implies [k] = \frac{[\text{concentration}]}{[\text{time}] \cdot [\text{concentration}]^n} = [\text{concentration}]^{1-n} \cdot [\text{time}]^{-1} [ − r A ] = [ k ] [ C ] n ⟹ [ k ] = [ time ] ⋅ [ concentration ] n [ concentration ] = [ concentration ] 1 − n ⋅ [ time ] − 1
Overall Order ( n n n ) Standard SI Units of k k k Imperial / Engineering Units Diagnostic Example
0 0 0 (Zero order) mol / ( L ⋅ s ) \text{mol}/(\text{L}\cdot\text{s}) mol / ( L ⋅ s ) or kmol / ( m 3 ⋅ s ) \text{kmol}/(\text{m}^3\cdot\text{s}) kmol / ( m 3 ⋅ s ) lbmol / ( ft 3 ⋅ hr ) \text{lbmol}/(\text{ft}^3\cdot\text{hr}) lbmol / ( ft 3 ⋅ hr ) Enzyme surface saturation, catalytic cracking
1 1 1 (First order) s − 1 \text{s}^{-1} s − 1 or min − 1 \text{min}^{-1} min − 1 or h − 1 \text{h}^{-1} h − 1 s − 1 \text{s}^{-1} s − 1 or hr − 1 \text{hr}^{-1} hr − 1 Radioactive decay, thermal cracking, cis-trans isomerization
2 2 2 (Second order) L / ( mol ⋅ s ) \text{L}/(\text{mol}\cdot\text{s}) L / ( mol ⋅ s ) or m 3 / ( kmol ⋅ s ) \text{m}^3/(\text{kmol}\cdot\text{s}) m 3 / ( kmol ⋅ s ) ft 3 / ( lbmol ⋅ hr ) \text{ft}^3/(\text{lbmol}\cdot\text{hr}) ft 3 / ( lbmol ⋅ hr ) Biomolecular gas condensations, dimerization
3 3 3 (Third order) L 2 / ( mol 2 ⋅ s ) \text{L}^2/(\text{mol}^2\cdot\text{s}) L 2 / ( mol 2 ⋅ s ) or m 6 / ( kmol 2 ⋅ s ) \text{m}^6/(\text{kmol}^2\cdot\text{s}) m 6 / ( kmol 2 ⋅ s ) ft 6 / ( lbmol 2 ⋅ hr ) \text{ft}^6/(\text{lbmol}^2\cdot\text{hr}) ft 6 / ( lbmol 2 ⋅ hr ) Recombination reactions: 2 NO + O 2 → 2 NO 2 2\text{NO} + \text{O}_2 \to 2\text{NO}_2 2 NO + O 2 → 2 NO 2
Fractional ( n = 1.5 n=1.5 n = 1.5 ) L 0.5 / ( mol 0.5 ⋅ s ) \text{L}^{0.5}/(\text{mol}^{0.5}\cdot\text{s}) L 0.5 / ( mol 0.5 ⋅ s ) ft 1.5 / ( lbmol 0.5 ⋅ hr ) \text{ft}^{1.5}/(\text{lbmol}^{0.5}\cdot\text{hr}) ft 1.5 / ( lbmol 0.5 ⋅ hr ) Free radical chain mechanisms (e.g., acetaldehyde pyrolysis)
Tip
Quick Unit Check for Reaction Order:
On multiple-choice PE exam questions, inspecting the units of k k k immediately reveals the overall reaction order without performing any algebra. If k k k has units of h − 1 \text{h}^{-1} h − 1 , the reaction is undeniably first order ( n = 1 n = 1 n = 1 ). If k k k is in m 3 / ( kmol ⋅ min ) \text{m}^3/(\text{kmol}\cdot\text{min}) m 3 / ( kmol ⋅ min ) , it is second order ( n = 2 n = 2 n = 2 ).
Gas-Phase Reactions in Partial Pressures
For ideal gas mixtures where partial pressure p i = C i R T p_i = C_i R T p i = C i RT , rate expressions are often written in terms of partial pressures: − r A = k p p A α p B β -r_A = k_p p_A^\alpha p_B^\beta − r A = k p p A α p B β
Where the pressure-basis rate constant k p k_p k p relates to the concentration-basis constant k c k_c k c via: k c = k p ( R T ) n k_c = k_p (R T)^n k c = k p ( RT ) n
Here, n = α + β n = \alpha + \beta n = α + β is the overall order, and R R R is the universal gas constant in compatible units.
3. Elementary vs. Non-Elementary Kinetics & Mechanisms
A central distinction in chemical kinetics is whether a reaction proceeds in a single molecular step or through a sequence of intermediate steps.
Elementary Reactions
An elementary reaction occurs exactly as written at the molecular level, in a single event where colliding molecules break and form bonds simultaneously. For elementary reactions, and only for elementary reactions, the partial reaction orders are identically equal to the stoichiometric coefficients:
Monomolecular: A ⟶ Products ⟹ − r A = k C A A \longrightarrow \text{Products} \implies -r_A = k C_A A ⟶ Products ⟹ − r A = k C A
Bimolecular: A + B ⟶ Products ⟹ − r A = k C A C B A + B \longrightarrow \text{Products} \implies -r_A = k C_A C_B A + B ⟶ Products ⟹ − r A = k C A C B
Bimolecular (self): 2 A ⟶ Products ⟹ − r A = k C A 2 2 A \longrightarrow \text{Products} \implies -r_A = k C_A^2 2 A ⟶ Products ⟹ − r A = k C A 2
Termolecular: 2 A + B ⟶ Products ⟹ − r A = k C A 2 C B 2 A + B \longrightarrow \text{Products} \implies -r_A = k C_A^2 C_B 2 A + B ⟶ Products ⟹ − r A = k C A 2 C B
Non-Elementary Reactions and Heterogeneous Catalysis
Most industrial processes are non-elementary , proceeding through complex multi-step reaction networks involving free radicals, ionic intermediates, or chemisorbed surface species. Their empirical reaction orders may be zero, fractional, or negative, and often vary with concentration.
A classic example is catalytic surface kinetics governed by the Langmuir-Hinshelwood-Hougen-Watson (LHHW) mechanism or enzymatic kinetics governed by the Michaelis-Menten model: − r A = k 1 C A 1 + k 2 C A -r_A = \frac{k_1 C_A}{1 + k_2 C_A} − r A = 1 + k 2 C A k 1 C A
Low reactant concentration ( k 2 C A ≪ 1 k_2 C_A \ll 1 k 2 C A ≪ 1 ): The denominator approaches 1 1 1 , and the rate reduces to pseudo-first-order kinetics: − r A ≈ k 1 C A -r_A \approx k_1 C_A − r A ≈ k 1 C A .
High reactant concentration ( k 2 C A ≫ 1 k_2 C_A \gg 1 k 2 C A ≫ 1 ): Catalyst active sites become fully saturated. The k 2 C A k_2 C_A k 2 C A term dominates the denominator, causing the concentration terms to cancel: − r A ≈ k 1 C A k 2 C A = k 1 k 2 = k a p p a r e n t -r_A \approx \frac{k_1 C_A}{k_2 C_A} = \frac{k_1}{k_2} = k_{apparent} − r A ≈ k 2 C A k 1 C A = k 2 k 1 = k a pp a re n t . The reaction shifts to pseudo-zero-order kinetics.
Reversible Reactions and Thermodynamic Consistency
For a reversible elementary reaction a A ⇌ b B a A \rightleftharpoons b B a A ⇌ b B , the net rate of disappearance of A A A is the difference between the forward and reverse rates: − r A = k f C A a − k r C B b = k f ( C A a − C B b K c ) -r_A = k_f C_A^a - k_r C_B^b = k_f \left( C_A^a - \frac{C_B^b}{K_c} \right) − r A = k f C A a − k r C B b = k f ( C A a − K c C B b )
At thermodynamic equilibrium, the macroscopic rate vanishes ( − r A = 0 -r_A = 0 − r A = 0 ): k f C A , e q a = k r C B , e q b ⟹ K c = k f k r = C B , e q b C A , e q a k_f C_{A,eq}^a = k_r C_{B,eq}^b \implies K_c = \frac{k_f}{k_r} = \frac{C_{B,eq}^b}{C_{A,eq}^a} k f C A , e q a = k r C B , e q b ⟹ K c = k r k f = C A , e q a C B , e q b
This relationship enforces strict thermodynamic consistency between kinetic rate constants and the chemical equilibrium constant K c K_c K c .
4. Differential and Integral Methods of Kinetic Data Analysis
To determine the reaction order and rate constant from laboratory batch reactor data, two primary approaches are utilized: the differential method and the integral method .
The Differential Method
In a constant-volume batch reactor, the rate of reaction is − r A = − d C A d t -r_A = -\frac{dC_A}{dt} − r A = − d t d C A . Taking the natural logarithm of a power-law rate law − r A = k C A n -r_A = k C_A^n − r A = k C A n : ln ( − d C A d t ) = ln ( k ) + n ln ( C A ) \ln\left( -\frac{dC_A}{dt} \right) = \ln(k) + n \ln(C_A) ln ( − d t d C A ) = ln ( k ) + n ln ( C A )
By measuring concentration C A C_A C A over time, determining numerical derivatives d C A / d t dC_A/dt d C A / d t , and plotting ln ( − d C A / d t ) \ln(-dC_A/dt) ln ( − d C A / d t ) versus ln ( C A ) \ln(C_A) ln ( C A ) :
The slope of the resulting straight line equals the reaction order n n n .
The y-intercept equals ln ( k ) \ln(k) ln ( k ) .
The Method of Initial Rates
A powerful variant of the differential method widely tested on the PE exam is the method of initial rates . Multiple experimental runs are initiated at varying starting concentrations ( C A 0 , C B 0 C_{A0}, C_{B0} C A 0 , C B 0 ), and the initial slope ( − d C A / d t ) t = 0 (-dC_A/dt)_{t=0} ( − d C A / d t ) t = 0 is measured before significant conversion occurs or product inhibition develops. Taking the ratio of rates between two runs where only one concentration is varied isolates that species' partial reaction order: ( − r A 0 ) 2 ( − r A 0 ) 1 = ( C A 0 , 2 C A 0 , 1 ) α \frac{(-r_{A0})_2}{(-r_{A0})_1} = \left( \frac{C_{A0,2}}{C_{A0,1}} \right)^\alpha ( − r A 0 ) 1 ( − r A 0 ) 2 = ( C A 0 , 1 C A 0 , 2 ) α
The Integral Method
The integral method postulates a tentative reaction order, integrates the differential rate expression analytically, and tests whether experimental ( C A , t ) (C_A, t) ( C A , t ) data yield a linear plot:
Zero Order ( − r A = k -r_A = k − r A = k ): − ∫ C A 0 C A d C A = k ∫ 0 t d t ⟹ C A = C A 0 − k t -\int_{C_{A0}}^{C_A} dC_A = k \int_0^t dt \implies C_A = C_{A0} - k t − ∫ C A 0 C A d C A = k ∫ 0 t d t ⟹ C A = C A 0 − k t
Linear plot: C A C_A C A vs. t t t has slope − k -k − k and intercept C A 0 C_{A0} C A 0 .
First Order ( − r A = k C A -r_A = k C_A − r A = k C A ): − ∫ C A 0 C A d C A C A = k ∫ 0 t d t ⟹ ln ( C A 0 C A ) = k t or C A = C A 0 e − k t -\int_{C_{A0}}^{C_A} \frac{dC_A}{C_A} = k \int_0^t dt \implies \ln\left( \frac{C_{A0}}{C_A} \right) = k t \quad \text{or} \quad C_A = C_{A0} e^{-k t} − ∫ C A 0 C A C A d C A = k ∫ 0 t d t ⟹ ln ( C A C A 0 ) = k t or C A = C A 0 e − k t
Linear plot: ln ( C A ) \ln(C_A) ln ( C A ) vs. t t t has slope − k -k − k and intercept ln ( C A 0 ) \ln(C_{A0}) ln ( C A 0 ) .
Second Order ( 2 A → Products 2A \to \text{Products} 2 A → Products , − r A = k C A 2 -r_A = k C_A^2 − r A = k C A 2 ): − ∫ C A 0 C A d C A C A 2 = k ∫ 0 t d t ⟹ 1 C A − 1 C A 0 = k t -\int_{C_{A0}}^{C_A} \frac{dC_A}{C_A^2} = k \int_0^t dt \implies \frac{1}{C_A} - \frac{1}{C_{A0}} = k t − ∫ C A 0 C A C A 2 d C A = k ∫ 0 t d t ⟹ C A 1 − C A 0 1 = k t
Linear plot: 1 / C A 1/C_A 1/ C A vs. t t t has slope + k +k + k and intercept 1 / C A 0 1/C_{A0} 1/ C A 0 .
5. Half-Life ( t 1 / 2 t_{1/2} t 1/2 ) Formulations and Reaction Order Diagnostics
The half-life ( t 1 / 2 t_{1/2} t 1/2 ) is the time required for the reactant concentration to drop to exactly half of its initial value ( C A = C A 0 / 2 C_A = C_{A0}/2 C A = C A 0 /2 , corresponding to fractional conversion X = 0.50 X = 0.50 X = 0.50 ). The functional dependence of t 1 / 2 t_{1/2} t 1/2 on initial concentration C A 0 C_{A0} C A 0 provides an instantaneous diagnostic test for reaction order.
Analytical Derivations for Constant Volume
Zero Order: C A = C A 0 2 = C A 0 − k t 1 / 2 ⟹ t 1 / 2 = C A 0 2 k C_A = \frac{C_{A0}}{2} = C_{A0} - k t_{1/2} \implies t_{1/2} = \frac{C_{A0}}{2 k} C A = 2 C A 0 = C A 0 − k t 1/2 ⟹ t 1/2 = 2 k C A 0
Behavior: Half-life is directly proportional to initial concentration. Doubling C A 0 C_{A0} C A 0 doubles t 1 / 2 t_{1/2} t 1/2 .
First Order: ln ( C A 0 C A 0 / 2 ) = ln ( 2 ) = k t 1 / 2 ⟹ t 1 / 2 = ln ( 2 ) k ≈ 0.69315 k \ln\left( \frac{C_{A0}}{C_{A0}/2} \right) = \ln(2) = k t_{1/2} \implies t_{1/2} = \frac{\ln(2)}{k} \approx \frac{0.69315}{k} ln ( C A 0 /2 C A 0 ) = ln ( 2 ) = k t 1/2 ⟹ t 1/2 = k ln ( 2 ) ≈ k 0.69315
Behavior: Half-life is strictly independent of initial concentration. Every successive half-life takes the exact same amount of time.
Second Order ( 2 A → Products 2A \to \text{Products} 2 A → Products ): 1 C A 0 / 2 − 1 C A 0 = 2 C A 0 − 1 C A 0 = 1 C A 0 = k t 1 / 2 ⟹ t 1 / 2 = 1 k C A 0 \frac{1}{C_{A0}/2} - \frac{1}{C_{A0}} = \frac{2}{C_{A0}} - \frac{1}{C_{A0}} = \frac{1}{C_{A0}} = k t_{1/2} \implies t_{1/2} = \frac{1}{k C_{A0}} C A 0 /2 1 − C A 0 1 = C A 0 2 − C A 0 1 = C A 0 1 = k t 1/2 ⟹ t 1/2 = k C A 0 1
Behavior: Half-life is inversely proportional to initial concentration. Doubling C A 0 C_{A0} C A 0 cuts t 1 / 2 t_{1/2} t 1/2 in half.
General Order n n n ( n ≠ 1 n \neq 1 n = 1 ): t 1 / 2 = 2 n − 1 − 1 ( n − 1 ) k C A 0 n − 1 ∝ C A 0 1 − n t_{1/2} = \frac{2^{n-1} - 1}{(n - 1) k C_{A0}^{n-1}} \propto C_{A0}^{1-n} t 1/2 = ( n − 1 ) k C A 0 n − 1 2 n − 1 − 1 ∝ C A 0 1 − n
Taking logarithms yields a direct method to find n n n from two half-life measurements: ( t 1 / 2 ) 1 ( t 1 / 2 ) 2 = ( C A 0 , 2 C A 0 , 1 ) n − 1 ⟹ n = 1 + ln [ ( t 1 / 2 ) 1 / ( t 1 / 2 ) 2 ] ln [ C A 0 , 2 / C A 0 , 1 ] \frac{(t_{1/2})_1}{(t_{1/2})_2} = \left( \frac{C_{A0,2}}{C_{A0,1}} \right)^{n-1} \implies n = 1 + \frac{\ln[(t_{1/2})_1 / (t_{1/2})_2]}{\ln[C_{A0,2} / C_{A0,1}]} ( t 1/2 ) 2 ( t 1/2 ) 1 = ( C A 0 , 1 C A 0 , 2 ) n − 1 ⟹ n = 1 + ln [ C A 0 , 2 / C A 0 , 1 ] ln [( t 1/2 ) 1 / ( t 1/2 ) 2 ] Reaction Order Diagnostic via Half-Life Progression:
- -----------------------------------------------------------
- Zero Order (n=0): t1/2(1) = 40 min ---> t1/2(2) = 20 min (Halves as CA drops)
- First Order (n=1): t1/2(1) = 40 min ---> t1/2(2) = 40 min (Constant)
- Second Order (n=2): t1/2(1) = 40 min ---> t1/2(2) = 80 min (Doubles as CA drops)
- 6. Summary Comparison Table: Kinetics by Reaction Order
Feature Zero Order ( n = 0 n=0 n = 0 ) First Order ( n = 1 n=1 n = 1 ) Second Order ( n = 2 n=2 n = 2 , single reactant)
Rate Law ( − r A -r_A − r A ) k k k k C A k C_A k C A k C A 2 k C_A^2 k C A 2
SI Units of k k k mol / ( L ⋅ s ) \text{mol}/(\text{L}\cdot\text{s}) mol / ( L ⋅ s ) s − 1 \text{s}^{-1} s − 1 L / ( mol ⋅ s ) \text{L}/(\text{mol}\cdot\text{s}) L / ( mol ⋅ s )
Integrated Form C A = C A 0 − k t C_A = C_{A0} - k t C A = C A 0 − k t ln ( C A 0 / C A ) = k t \ln(C_{A0}/C_A) = k t ln ( C A 0 / C A ) = k t 1 / C A − 1 / C A 0 = k t 1/C_A - 1/C_{A0} = k t 1/ C A − 1/ C A 0 = k t
Conversion Form X = k t C A 0 X = \frac{k t}{C_{A0}} X = C A 0 k t X = 1 − e − k t X = 1 - e^{-k t} X = 1 − e − k t X = k C A 0 t 1 + k C A 0 t X = \frac{k C_{A0} t}{1 + k C_{A0} t} X = 1 + k C A 0 t k C A 0 t
Half-Life ( t 1 / 2 t_{1/2} t 1/2 ) C A 0 2 k \frac{C_{A0}}{2 k} 2 k C A 0 ln 2 k ≈ 0.693 k \frac{\ln 2}{k} \approx \frac{0.693}{k} k l n 2 ≈ k 0.693 1 k C A 0 \frac{1}{k C_{A0}} k C A 0 1
Time for Complete Conversion ( X = 1 X=1 X = 1 ) Finite: t = C A 0 / k t = C_{A0}/k t = C A 0 / k Infinite ( t → ∞ t \to \infty t → ∞ ) Infinite ( t → ∞ t \to \infty t → ∞ )
Linear Plot C A C_A C A vs. t t t (slope − k -k − k ) ln ( C A ) \ln(C_A) ln ( C A ) vs. t t t (slope − k -k − k ) 1 / C A 1/C_A 1/ C A vs. t t t (slope + k +k + k )
- 7. Step-by-Step Worked Numerical Example: Method of Initial Rates & Rate Law Determination
- Problem Statement
An engineer is characterizing the liquid-phase synthesis of a specialty monomer governed by the stoichiometry: 2 A + B ⟶ C + 2 D 2 A + B \longrightarrow C + 2 D 2 A + B ⟶ C + 2 D
Four isothermal batch experiments are performed at 25.0 ∘ C 25.0^\circ\text{C} 25. 0 ∘ C in a constant-volume laboratory reactor. The initial rates of disappearance of reactant A A A ( ( − r A 0 ) (-r_{A0}) ( − r A 0 ) ) are recorded as a function of initial concentrations:
Run Number Initial C A 0 C_{A0} C A 0 ( mol/L \text{mol/L} mol/L ) Initial C B 0 C_{B0} C B 0 ( mol/L \text{mol/L} mol/L ) Measured Initial Rate ( − r A 0 ) (-r_{A0}) ( − r A 0 ) ( mol / ( L ⋅ s ) \text{mol}/(\text{L}\cdot\text{s}) mol / ( L ⋅ s ) )
- 1 0.200 0.200 0.200 0.100 0.100 0.100 0.00400 0.00400 0.00400
- 2 0.400 0.400 0.400 0.100 0.100 0.100 0.01600 0.01600 0.01600
- 3 0.200 0.200 0.200 0.300 0.300 0.300 0.01200 0.01200 0.01200
- 4 0.400 0.400 0.400 0.300 0.300 0.300 0.04800 0.04800 0.04800
Calculate:
The partial reaction orders α \alpha α and β \beta β , and the overall reaction order n n n .
The numerical value and dimensional units of the reaction rate constant k A k_A k A based on species A A A .
The reaction rate constant k B k_B k B based on the consumption of species B B B , and k C k_C k C based on the formation of product C C C .
The predicted initial rate of formation of product D D D ( r D 0 r_{D0} r D 0 ) if a new run is initiated with C A 0 = 0.500 mol/L C_{A0} = 0.500\text{ mol/L} C A 0 = 0.500 mol/L and C B 0 = 0.200 mol/L C_{B0} = 0.200\text{ mol/L} C B 0 = 0.200 mol/L .
Step 1: Determine Partial Reaction Orders
The general power-law rate expression based on species A A A is: − r A = k A C A α C B β -r_A = k_A C_A^\alpha C_B^\beta − r A = k A C A α C B β
To find α \alpha α , compare Run 2 and Run 1, where C B 0 C_{B0} C B 0 is held constant at 0.100 mol/L 0.100\text{ mol/L} 0.100 mol/L while C A 0 C_{A0} C A 0 doubles: ( − r A 0 ) 2 ( − r A 0 ) 1 = 0.01600 0.00400 = 4.00 = ( 0.400 0.200 ) α = ( 2.00 ) α ⟹ α = 2 \frac{(-r_{A0})_2}{(-r_{A0})_1} = \frac{0.01600}{0.00400} = 4.00 = \left( \frac{0.400}{0.200} \right)^\alpha = (2.00)^\alpha \implies \mathbf{\alpha = 2} ( − r A 0 ) 1 ( − r A 0 ) 2 = 0.00400 0.01600 = 4.00 = ( 0.200 0.400 ) α = ( 2.00 ) α ⟹ α = 2
The reaction is second order with respect to reactant A A A .
To find β \beta β , compare Run 3 and Run 1, where C A 0 C_{A0} C A 0 is held constant at 0.200 mol/L 0.200\text{ mol/L} 0.200 mol/L while C B 0 C_{B0} C B 0 triples: ( − r A 0 ) 3 ( − r A 0 ) 1 = 0.01200 0.00400 = 3.00 = ( 0.300 0.100 ) β = ( 3.00 ) β ⟹ β = 1 \frac{(-r_{A0})_3}{(-r_{A0})_1} = \frac{0.01200}{0.00400} = 3.00 = \left( \frac{0.300}{0.100} \right)^\beta = (3.00)^\beta \implies \mathbf{\beta = 1} ( − r A 0 ) 1 ( − r A 0 ) 3 = 0.00400 0.01200 = 3.00 = ( 0.100 0.300 ) β = ( 3.00 ) β ⟹ β = 1
The reaction is first order with respect to reactant B B B .
The overall reaction order is: n = α + β = 2 + 1 = 3 ( third order overall ) n = \alpha + \beta = 2 + 1 = \mathbf{3 \quad (\text{third order overall})} n = α + β = 2 + 1 = 3 ( third order overall )
(Cross-check with Run 4: ( − r A 0 ) 4 = k A ( 0.400 ) 2 ( 0.300 ) = k A ( 0.0480 ) (-r_{A0})_4 = k_A (0.400)^2 (0.300) = k_A (0.0480) ( − r A 0 ) 4 = k A ( 0.400 ) 2 ( 0.300 ) = k A ( 0.0480 ) . Ratio to Run 1 is 0.04800 / 0.00400 = 12.0 = 2 2 × 3 1 = 12.0 0.04800 / 0.00400 = 12.0 = 2^2 \times 3^1 = 12.0 0.04800/0.00400 = 12.0 = 2 2 × 3 1 = 12.0 . Matches perfectly).
Step 2: Calculate Value and Units of Rate Constant k A k_A k A
Using experimental Run 1: k A = ( − r A 0 ) 1 C A 0 , 1 2 C B 0 , 1 = 0.00400 mol / ( L ⋅ s ) ( 0.200 mol/L ) 2 ⋅ ( 0.100 mol/L ) = 0.00400 0.0400 × 0.100 = 0.00400 0.00400 = 1.000 L 2 / ( mol 2 ⋅ s ) k_A = \frac{(-r_{A0})_1}{C_{A0,1}^2 C_{B0,1}} = \frac{0.00400\text{ mol}/(\text{L}\cdot\text{s})}{(0.200\text{ mol/L})^2 \cdot (0.100\text{ mol/L})} = \frac{0.00400}{0.0400 \times 0.100} = \frac{0.00400}{0.00400} = \mathbf{1.000\text{ L}^2/(\text{mol}^2\cdot\text{s})} k A = C A 0 , 1 2 C B 0 , 1 ( − r A 0 ) 1 = ( 0.200 mol/L ) 2 ⋅ ( 0.100 mol/L ) 0.00400 mol / ( L ⋅ s ) = 0.0400 × 0.100 0.00400 = 0.00400 0.00400 = 1.000 L 2 / ( mol 2 ⋅ s )
Units verification for third order ( n = 3 n=3 n = 3 ): [ k ] = [ concentration ] 1 − 3 [ time ] − 1 = ( mol L ) − 2 s − 1 = L 2 / ( mol 2 ⋅ s ) [k] = [\text{concentration}]^{1-3} [\text{time}]^{-1} = \left(\frac{\text{mol}}{\text{L}}\right)^{-2} \text{s}^{-1} = \mathbf{\text{L}^2/(\text{mol}^2\cdot\text{s})} [ k ] = [ concentration ] 1 − 3 [ time ] − 1 = ( L mol ) − 2 s − 1 = L 2 / ( mol 2 ⋅ s )
Step 3: Relate Rate Constants by Stoichiometry
From the stoichiometry 2 A + B → C + 2 D 2A + B \to C + 2D 2 A + B → C + 2 D : − r A 2 = − r B 1 = r C 1 = r D 2 \frac{-r_A}{2} = \frac{-r_B}{1} = \frac{r_C}{1} = \frac{r_D}{2} 2 − r A = 1 − r B = 1 r C = 2 r D
Therefore: − r B = 1 2 ( − r A ) = 1 2 k A C A 2 C B = k B C A 2 C B ⟹ k B = 1 2 k A = 0.500 L 2 / ( mol 2 ⋅ s ) -r_B = \frac{1}{2}(-r_A) = \frac{1}{2} k_A C_A^2 C_B = k_B C_A^2 C_B \implies k_B = \frac{1}{2} k_A = \mathbf{0.500\text{ L}^2/(\text{mol}^2\cdot\text{s})} − r B = 2 1 ( − r A ) = 2 1 k A C A 2 C B = k B C A 2 C B ⟹ k B = 2 1 k A = 0.500 L 2 / ( mol 2 ⋅ s ) r C = 1 2 ( − r A ) = 1 2 k A C A 2 C B = k C C A 2 C B ⟹ k C = 1 2 k A = 0.500 L 2 / ( mol 2 ⋅ s ) r_C = \frac{1}{2}(-r_A) = \frac{1}{2} k_A C_A^2 C_B = k_C C_A^2 C_B \implies k_C = \frac{1}{2} k_A = \mathbf{0.500\text{ L}^2/(\text{mol}^2\cdot\text{s})} r C = 2 1 ( − r A ) = 2 1 k A C A 2 C B = k C C A 2 C B ⟹ k C = 2 1 k A = 0.500 L 2 / ( mol 2 ⋅ s )
Step 4: Calculate Predicted Initial Rate of Formation of Product D D D
For C A 0 = 0.500 mol/L C_{A0} = 0.500\text{ mol/L} C A 0 = 0.500 mol/L and C B 0 = 0.200 mol/L C_{B0} = 0.200\text{ mol/L} C B 0 = 0.200 mol/L : − r A 0 = k A C A 0 2 C B 0 = 1.000 × ( 0.500 ) 2 × ( 0.200 ) = 1.000 × 0.250 × 0.200 = 0.0500 mol / ( L ⋅ s ) -r_{A0} = k_A C_{A0}^2 C_{B0} = 1.000 \times (0.500)^2 \times (0.200) = 1.000 \times 0.250 \times 0.200 = 0.0500\text{ mol}/(\text{L}\cdot\text{s}) − r A 0 = k A C A 0 2 C B 0 = 1.000 × ( 0.500 ) 2 × ( 0.200 ) = 1.000 × 0.250 × 0.200 = 0.0500 mol / ( L ⋅ s )
Since r D = 2 2 ( − r A ) = − r A r_D = \frac{2}{2}(-r_A) = -r_A r D = 2 2 ( − r A ) = − r A : r D 0 = − r A 0 = 0.0500 mol / ( L ⋅ s ) r_{D0} = -r_{A0} = \mathbf{0.0500\text{ mol}/(\text{L}\cdot\text{s})} r D 0 = − r A 0 = 0.0500 mol / ( L ⋅ s )
- 8. Critical PE Exam Traps & Pitfalls
- Trap 1: Assuming Exponents Equal Stoichiometric Coefficients
Never infer the rate law directly from the balanced chemical equation unless the problem statement explicitly confirms that the reaction is elementary . For instance, the reaction 2 NO 2 + F 2 → 2 NO 2 F 2 \text{NO}_2 + \text{F}_2 \to 2 \text{NO}_2\text{F} 2 NO 2 + F 2 → 2 NO 2 F has overall stoichiometry of order 3, but laboratory kinetics reveal it is first order in each reactant: − r NO 2 = k C NO 2 C F 2 -r_{\text{NO}_2} = k C_{\text{NO}_2} C_{\text{F}_2} − r NO 2 = k C NO 2 C F 2 (order 2 overall). Always rely on experimental data or an explicit "elementary" descriptor.
Trap 2: Forgetting to Convert Basis When Stating k k k
On exam questions involving a A + b B → c C a A + b B \to c C a A + b B → c C , the question may state that k A = 0.40 L / ( mol ⋅ s ) k_A = 0.40\text{ L}/(\text{mol}\cdot\text{s}) k A = 0.40 L / ( mol ⋅ s ) and ask for the rate of formation of product C C C . You must multiply by c / a c/a c / a . Failing to convert between k A k_A k A , k B k_B k B , and k C k_C k C is one of the most common numerical distractors created by exam writers.
Trap 3: Inverting the Half-Life Dependence
Remember that t 1 / 2 ∝ C A 0 1 − n t_{1/2} \propto C_{A0}^{1-n} t 1/2 ∝ C A 0 1 − n . For a second-order reaction ( n = 2 n = 2 n = 2 ), 1 − n = − 1 1-n = -1 1 − n = − 1 , meaning t 1 / 2 = 1 / ( k C A 0 ) t_{1/2} = 1/(k C_{A0}) t 1/2 = 1/ ( k C A 0 ) . If an engineer doubles the starting concentration for a second-order reaction, the half-life is cut in half, NOT doubled. Conversely, for a zero-order reaction ( n = 0 n = 0 n = 0 ), 1 − n = + 1 1-n = +1 1 − n = + 1 , so doubling concentration doubles the time required to react 50 % 50\% 50% .
Trap 4: Unit Errors in Ideal Gas Rate Laws
When converting between concentration-based rate constants ( k c k_c k c ) and pressure-based rate constants ( k p k_p k p ), remember k c = k p ( R T ) n k_c = k_p (R T)^n k c = k p ( RT ) n . The exponent is the overall order n n n , not the partial order of A A A , and R R R must be expressed in units matching pressure and concentration (e.g., 0.08206 L ⋅ atm / ( mol ⋅ K ) 0.08206\text{ L}\cdot\text{atm}/(\text{mol}\cdot\text{K}) 0.08206 L ⋅ atm / ( mol ⋅ K ) or 8.314 × 10 − 5 m 3 ⋅ bar / ( mol ⋅ K ) 8.314\times 10^{-5}\text{ m}^3\cdot\text{bar}/(\text{mol}\cdot\text{K}) 8.314 × 1 0 − 5 m 3 ⋅ bar / ( mol ⋅ K ) ).