Study guide
11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics
PE Chemical Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the PE Chemical Exam How to Use This Guide and the NCEES Handbook
2 Chapter 1: Material Balances & Flowsheet Calculations
1.1 Degree-of-Freedom Analysis & Process Flowsheet Accounting 1.2 Steady-State Material Balances (Reactive & Non-Reactive Systems) 1.3 Recycle, Bypass, and Purge Operations
3 Chapter 2: Energy Balances & Thermochemistry
2.1 Enthalpy Accounting, Sensible Heat, and Phase Changes 2.2 Heats of Reaction, Formation, and Adiabatic Flame Temperatures 2.3 Unsteady-State Mass and Energy Balances
4 Chapter 3: Fluid Statics & Incompressible Pipe Flow
3.1 Fluid Statics, Pressure Measurement, and Manometry 3.2 Incompressible Flow, Friction Factors, and the Moody Diagram 3.3 Minor Losses, Equivalent Length, and Piping Networks 3.4 Pumps, Compressors, and NPSH Calculations
5 Chapter 4: Advanced Fluid Dynamics & Compressible Flow
4.1 Compressible Gas Flow, Sonic Velocity, and Choked Flow 4.2 Flow Measurement Devices (Orifices, Venturis, Rotameters) 4.3 Multiphase Flow and Fluidization Principles 4.4 Mixing, Agitation, and Agitator Scale-Up
6 Chapter 5: Thermodynamic Laws & Fundamental Relations
5.1 First and Second Laws, Heat Engines, and Carnot Efficiency 5.2 Entropy, Availability, and Exergy Analysis 5.3 Fundamental Property Relations and Maxwell Equations
7 Chapter 6: Real Gases & Equations of State
6.1 Volumetric Properties and Compressibility Factor Charts 6.2 Cubic Equations of State (vdW, RK, SRK, and Peng-Robinson) 6.3 Residual Properties and Enthalpy/Entropy Departure Functions
8 Chapter 7: Phase & Chemical Reaction Equilibria
7.1 Pure Component Vapor Pressure and Phase Equilibria 7.2 Vapor-Liquid Equilibrium (VLE), Raoult's Law, and Activity Coefficients 7.3 Chemical Reaction Equilibria and Equilibrium Constant Calculation
9 Chapter 8: Heat Transfer Mechanisms & Conduction
8.1 Steady-State Conduction in Planar, Cylindrical, and Spherical Geometries 8.2 Convective Heat Transfer and Dimensionless Correlations 8.3 Thermal Radiation, Emissivity, and Surface Radiation Exchange
10 Chapter 9: Heat Exchanger Design & Phase Change
9.1 Shell-and-Tube Exchanger Design, TEMA Standards, and LMTD 9.2 Effectiveness-NTU Method and Exchanger Rating 9.3 Boiling Regimes, Condensation Phenomena, and Fouling Resistances
11 Chapter 10: Mass Transfer Fundamentals & Diffusion
10.1 Molecular Diffusion, Fick's Laws, and Equimolar Counterdiffusion 10.2 Convective Mass Transfer and Film Theories 10.3 Mass Transfer Dimensionless Numbers (Sherwood, Schmidt, Peclet)
12 Chapter 11: Distillation Operations
11.1 Vapor-Liquid Equilibrium and Relative Volatility in Distillation 11.2 McCabe-Thiele Method for Binary Distillation 11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics 11.4 Multicomponent Distillation Fundamentals and Key Components
13 Chapter 12: Rate-Controlled & Equilibrium Separations
12.1 Gas Absorption, Stripping, and the Kremser Equation 12.2 Liquid-Liquid Extraction and Ternary Phase Equilibria 12.3 Adsorption, Membrane Separations, and Drying Operations 12.4 Filtration, Crystallization, and Solid-Fluid Separations
14 Chapter 13: Chemical Kinetics & Ideal Isothermal Reactors
13.1 Reaction Rates, Rate Laws, and Order of Reaction 13.2 Temperature Dependence and the Arrhenius Equation 13.3 Batch Reactors and Continuous Stirred-Tank Reactors (CSTR) 13.4 Plug Flow Reactors (PFR) and Reactor Combinations
15 Chapter 14: Non-Ideal Flow, Non-Isothermal Reactors & Catalysis
14.1 Yield, Selectivity, and Multiple Reactions (Series and Parallel) 14.2 Non-Isothermal Reactor Design and Thermal Runaway 14.3 Heterogeneous Catalysis, Thiele Modulus, and RTD Models
16 Chapter 15: Physical & Transport Properties of Fluids
15.1 Fluid Density, Specific Gravity, and Viscosity Correlations 15.2 Thermal Conductivity and Specific Heat Capacities 15.3 Estimation Methods and Corresponding States Principles
17 Chapter 16: Materials of Construction & Corrosion
16.1 Mechanical Properties and Materials Selection in Chemical Plants 16.2 Corrosion Mechanisms, Materials Degradation, and Prevention
18 Chapter 17: Process Safety & Pressure Relief Systems
17.1 Hazard Identification Methodologies (HAZOP, FMEA, What-If) 17.2 Pressure Relief Valve (PRV) and Rupture Disk Sizing 17.3 Flammability, Explosions, and Toxic Dispersion Limits 17.4 Inerting, Purging, Discharge Location, and Containment
19 Chapter 18: Process Control & Engineering Economics
18.1 Process Dynamics and Feedback Control Loops 18.2 PID Controller Tuning and Loop Stability 18.3 Chemical Plant Capital Cost Estimation and Profitability Analysis 18.4 Field Instrumentation, Control Valves, Alarms, and Safety Instrumented Systems
20 Chapter 19: Process Design, Equipment Selection & Environmental Compliance
19.1 Process Flow Diagrams, P&IDs, Scale-Up, and Plant Siting 19.2 Process Equipment Selection, Sizing, and Optimization 19.3 Emissions Evaluation, Mitigation, and Remediation
21 Chapter 20: Plant Operation, Reliability & Continuous Improvement
20.1 Operating Procedures, Startup, and Shutdown 20.2 Mechanical Integrity, Reliability, and Failure Mechanisms 20.3 Debottlenecking, Optimization, and Troubleshooting
11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics
Key Takeaways Explain This Topic AI
Column internals are classified into trayed columns (discrete staged contact: sieve, valve, bubble-cap) and packed columns (continuous differential contact: random vs structured packing); packed columns provide ultra-low pressure drops (1 to 2 mbar/theoretical stage), making them mandatory for vacuum and heat-sensitive systems.
Tray columns are bounded by distinct hydraulic limits: jet (entrainment) flooding at high vapor rates, downcomer backup flooding at high liquid loads, downcomer choke from inadequate froth disengagement, and weeping or dumping at low vapor velocities.
Valve trays offer broad operating flexibility (turndown ratios of 4:1 to 5:1) by using movable metal discs that throttle orifice area with fluctuating vapor rates, preventing weeping; sieve trays are inexpensive and low-fouling but offer limited turndown (2:1), while bubble-cap trays offer >8:1 turndown at high capital and pressure drop penalties.
Total tray pressure drop h_t = h_d + h_L + h_R comprises dry tray drop h_d (orifice kinetic energy), clear liquid head h_L (weir crest plus weir height), and residual surface tension drop h_R; downcomer backup h_dc must not exceed 50% of the tray spacing plus weir height to prevent catastrophic downcomer flooding.
Packed column height is sized via the Height Equivalent to a Theoretical Plate (HETP, Z = N_ideal * HETP) or via two-film mass transfer units (Z = HTU_OG * NTU_OG); HETP and HTU_OG are linked through the stripping factor lambda = m * V / L via HETP = HTU_OG * [ln(lambda) / (lambda - 1)].
Last updated: September 2026
11.3 Packed vs Tray Columns, Flooding, and Tray Hydraulics
Once the theoretical stage requirements and reflux ratios are established, chemical engineers must translate these thermodynamic quantities into physical hardware. On the NCEES PE Chemical Exam , questions frequently test the mechanical selection, hydraulic boundaries, and sizing of column internals . Operating an industrial column requires balancing vapor and liquid flow rates within a stable operating window; exceeding these limits induces hydraulic failure modes such as flooding , weeping , dumping , or entrainment .
1. Classification of Distillation Internals: Trays vs. Packings
Distillation equipment is divided into two broad physical contact regimes:
Trayed (Staged) Columns: Vapor and liquid contact each other in discrete, step-wise equilibrium stages on horizontal plates.
Packed (Continuous Differential) Columns: Vapor and liquid contact each other continuously and countercurrently across high-surface-area packing elements. [ TRAY COLUMN ] [ PACKED COLUMN ]
- Liquid In +------------+ Liquid In +------------+
- | | Downcomer | | | Liquid |
- v | | | v | Distributor|
- +----+ v | | +----+ +------------+
- |Tray|======> | | |Bed | |~~~~~~~~~~~~|
- +----+ v | | 1 | | Structured |
- +------------+ +----+ | or Random |
- | Active | | Packing |
- | Froth Area | |~~~~~~~~~~~~|
- +------------+ +------------+
- ^ ^ Vapor Up
- | Vapor Up |
- Tray Types
Sieve Trays: Flat metal sheets perforated with small round holes ( 3 – 12 mm 3\text{--}12\text{ mm} 3 – 12 mm or 1 / 8 to 1 / 2 inch 1/8\text{ to }1/2\text{ inch} 1/8 to 1/2 inch diameter). Liquid flows horizontally across the tray while vapor jets upward through the perforations. Lowest capital cost, lowest maintenance, and high capacity, but limited turndown ratio ( 2 : 1 2:1 2 : 1 to 2.5 : 1 2.5:1 2.5 : 1 ). At reduced vapor throughput, liquid weeps directly through the holes.
Valve Trays: Perforations are covered with liftable metal discs or rectangular caps (moving valves) or coined integral indentations (fixed valves). At low vapor rates, the valves sit closed, restricting open area and preventing weeping; as vapor flow increases, the valves rise, accommodating higher gas throughput. Excellent turndown ratio ( 4 : 1 4:1 4 : 1 to 5 : 1 5:1 5 : 1 ) with capacity and efficiency comparable to sieve trays. Standard for wide-range refinery services.
Bubble-Cap Trays: Consist of stationary vapor risers covered by inverted cylindrical caps with vertical slots. The riser extends above the tray deck, creating a permanent liquid seal even at zero vapor flow. Exceptional turndown ( > 8 : 1 >8:1 > 8 : 1 ) and zero weeping, but high capital cost, severe pressure drop (2–3 times higher than sieve trays), and susceptibility to fouling.
Packing Types
Random (Dumped) Packing: Discrete elements dumped randomly into the shell. Evolution: First-generation (ceramic Raschig rings, Berl saddles; low capacity, high Δ P \Delta P Δ P ), Second-generation (metal Pall rings; open slotted walls), Third-generation (IMTP, Jaeger Tri-Packs, Nutter Rings; high void fraction > 95 % >95\% > 95% , low pressure drop).
Structured Packing: Corrugated wire gauze or sheet metal plates arranged in parallel vertical bundles oriented at alternating angles ( 45 ∘ 45^\circ 4 5 ∘ or 60 ∘ 60^\circ 6 0 ∘ ). Provides maximum geometric surface area ( 200 – 500 m 2 / m 3 200\text{--}500\text{ m}^2/\text{m}^3 200 – 500 m 2 / m 3 ) with an ultra-low pressure drop ( ∼ 0.5 – 1.5 mbar \sim 0.5\text{--}1.5\text{ mbar} ∼ 0.5 – 1.5 mbar per theoretical stage, compared to 4 – 8 mbar 4\text{--}8\text{ mbar} 4 – 8 mbar per tray). Mandatory for vacuum distillation, offshore motion units, and heat-sensitive chemical separations.
2. Tray Operating Windows & Hydraulic Failure Regimes
A tray operates stably only within a bounded region on a plot of vapor rate ( V V V ) versus liquid rate ( L L L ): Vapor Rate (V) ^
- | JET (ENTRAINMENT) FLOODING
- |---------------------------------------------
- | / / DOWNCOMER
- | STABLE / / BACKUP
- | OPERATING / / FLOODING
- | WINDOW / /
- | / / DOWNCOMER
- | / / CHOKE
- |---------------------------/
- | WEEPING / DUMPING
- +--------------------------------------------->
- 0 Liquid Rate (L)
- Hydraulic Failure Mechanisms
Jet (Entrainment) Flooding: At excessive vapor velocities, the upward kinetic energy of the gas shears liquid droplets from the froth and carries them up to the tray above. This liquid recycling degrades the concentration gradient, collapses tray separation efficiency, and increases column pressure drop.
Downcomer Backup Flooding: Occurs when the aerated liquid level inside the downcomer backs up and reaches the top of the weir of the tray above. Caused by high liquid flow rates, inadequate downcomer cross-sectional area, or excessive tray pressure drop forcing liquid up the downcomer.
Downcomer Choke: At very high liquid flow rates, vapor disengagement inside the downcomer is incomplete. Aerated, low-density froth enters the bottom downcomer clearance, creating a choking frictional resistance that prevents liquid drainage.
Weeping: Occurs when vapor velocity drops below the minimum threshold required to support the liquid pool on the tray deck. Liquid begins to drip through the perforations, bypassing horizontal crossflow and reducing contact efficiency.
Dumping: Extreme weeping where the entire liquid pool dumps through the perforations, the tray dries out, and vapor-liquid contact collapses completely.
- 3. Quantitative Tray Hydraulics & Flooding Correlations
- Total Tray Pressure Drop ( h t h_t h t )
Total tray pressure drop is expressed in head of clear liquid ( h t h_t h t , in mm \text{mm} mm or inches \text{inches} inches of liquid): h t = h d + h L + h R h_t = h_d + h_L + h_R h t = h d + h L + h R Δ P t r a y = ρ L g h t \Delta P_{tray} = \rho_L g h_t Δ P t r a y = ρ L g h t
Where:
Dry Tray Drop ( h d h_d h d ): Head loss due to vapor kinetic energy dissipating across the perforations: h d = 0.003 ( u h C v ) 2 ( ρ V ρ L ) h_d = 0.003 \left( \frac{u_h}{C_v} \right)^2 \left( \frac{\rho_V}{\rho_L} \right) h d = 0.003 ( C v u h ) 2 ( ρ L ρ V ) u h u_h u h is vapor velocity through hole area, and C v C_v C v is the discharge orifice coefficient ( C v ≈ 0.70 – 0.75 C_v \approx 0.70\text{--}0.75 C v ≈ 0.70 – 0.75 ).
Clear Liquid Head ( h L h_L h L ): The equivalent static liquid pool on the tray: h L = β ( h w + h o w ) h_L = \beta (h_w + h_{ow}) h L = β ( h w + h o w ) Where h w h_w h w is outlet weir height ( 25 – 50 mm 25\text{--}50\text{ mm} 25 – 50 mm or 1 – 2 in 1\text{--}2\text{ in} 1 – 2 in ), β \beta β is the aeration factor (typically 0.4 – 0.7 0.4\text{--}0.7 0.4 – 0.7 ), and h o w h_{ow} h o w is the liquid crest over the weir, calculated from the Francis Weir Formula : h o w = 0.664 ( Q L L w ) 2 / 3 [ SI units: Q L in m 3 / s , L w in m , h o w in m ] h_{ow} = 0.664 \left( \frac{Q_L}{L_w} \right)^{2/3} \quad [\text{SI units: } Q_L \text{ in m}^3/\text{s}, L_w \text{ in m}, h_{ow} \text{ in m}] h o w = 0.664 ( L w Q L ) 2/3 [ SI units: Q L in m 3 / s , L w in m , h o w in m ]
Residual Pressure Drop ( h R h_R h R ): Head required to overcome liquid surface tension to form bubbles ( h R ≈ 6 – 12 mm h_R \approx 6\text{--}12\text{ mm} h R ≈ 6 – 12 mm liquid).
Downcomer Backup ( h d c h_{dc} h d c )
The liquid head backed up inside the downcomer must balance total tray pressure drop, clear liquid head, and frictional entrance loss under the downcomer apron ( h u d h_{ud} h u d ): h d c = h t + h w + h o w + h u d h_{dc} = h_t + h_w + h_{ow} + h_{ud} h d c = h t + h w + h o w + h u d
Where: h u d = 0.06 ( Q L A u d a ) 2 ( A u d a = clearance area under apron ) h_{ud} = 0.06 \left( \frac{Q_L}{A_{uda}} \right)^2 \quad (A_{uda} = \text{clearance area under apron}) h u d = 0.06 ( A u d a Q L ) 2 ( A u d a = clearance area under apron )
To prevent downcomer backup flooding, industrial engineering standards (e.g., Kister, Fair) dictate that clear liquid backup must not exceed 50 % 50\% 50% of the tray spacing ( T . S . T.S. T . S . ) plus weir height, accounting for a downcomer froth density of ϕ d c ≈ 0.50 \phi_{dc} \approx 0.50 ϕ d c ≈ 0.50 : h d c ≤ 0.50 ⋅ ( T . S . + h w ) h_{dc} \le 0.50 \cdot (T.S. + h_w) h d c ≤ 0.50 ⋅ ( T . S . + h w )
Fair's Entrainment Flooding Correlation
Entrainment flooding is evaluated using Fair's Capacity Parameter ( C s b C_{sb} C s b ) , derived from the Souders-Brown terminal droplet settling velocity: ν f = C s b ( σ 20 ) 0.2 ρ L − ρ V ρ V \nu_{f} = C_{sb} \left( \frac{\sigma}{20} \right)^{0.2} \sqrt{\frac{\rho_L - \rho_V}{\rho_V}} ν f = C s b ( 20 σ ) 0.2 ρ V ρ L − ρ V
Where:
u f u_f u f = flooding vapor velocity based on net active bubbling area ( A n = A c o l − A d c A_n = A_{col} - A_{dc} A n = A co l − A d c ), in m/s \text{m/s} m/s or ft/s \text{ft/s} ft/s .
σ \sigma σ = liquid surface tension ( mN/m \text{mN/m} mN/m or dyn/cm \text{dyn/cm} dyn/cm ; reference is 20 dyn/cm 20\text{ dyn/cm} 20 dyn/cm ).
ρ L , ρ V \rho_L, \rho_V ρ L , ρ V = liquid and vapor mass densities ( kg/m 3 \text{kg/m}^3 kg/m 3 or lb/ft 3 \text{lb/ft}^3 lb/ft 3 ).
C s b C_{sb} C s b = empirical capacity factor, evaluated as a function of tray spacing ( T . S . T.S. T . S . ) and the dimensionless Flow Parameter ( F l v F_{lv} F l v ) : F l v = ( L V ) ρ V ρ L F_{lv} = \left( \frac{L}{V} \right) \sqrt{\frac{\rho_V}{\rho_L}} F l v = ( V L ) ρ L ρ V
Where L L L and V V V are mass flow rates ( kg/h \text{kg/h} kg/h or lb/h \text{lb/h} lb/h ). Standard design practice operates at 75 % 75\% 75% to 85 % 85\% 85% of flooding velocity ( u d e s = 0.80 ⋅ u f u_{des} = 0.80 \cdot u_f u d es = 0.80 ⋅ u f ).
4. Packed Column Sizing: HETP vs. Transfer Unit Theory
In packed columns, separation occurs continuously along the bed height ( Z Z Z ).
Height Equivalent to a Theoretical Plate (HETP)
The simplest industrial sizing approach converts theoretical equilibrium stages ( N i d e a l N_{ideal} N i d e a l ) directly into packed bed height: Z = N i d e a l ⋅ HETP Z = N_{ideal} \cdot \text{HETP} Z = N i d e a l ⋅ HETP
Typical industrial HETP values:
High-efficiency structured packing: HETP = 0.25 – 0.45 m \text{HETP} = 0.25\text{--}0.45\text{ m} HETP = 0.25 – 0.45 m ( 10 – 18 inches 10\text{--}18\text{ inches} 10 – 18 inches ).
Modern random packing (Pall rings, IMTP): HETP = 0.45 – 0.75 m \text{HETP} = 0.45\text{--}0.75\text{ m} HETP = 0.45 – 0.75 m ( 18 – 30 inches 18\text{--}30\text{ inches} 18 – 30 inches ).
Rule of thumb for random packing: HETP ≈ 1.0 to 1.5 \text{HETP} \approx 1.0\text{ to }1.5 HETP ≈ 1.0 to 1.5 times column diameter for small columns, capping at ∼ 0.6 – 0.9 m \sim 0.6\text{--}0.9\text{ m} ∼ 0.6 – 0.9 m for large towers.
Transfer Unit Theory (HTU and NTU)
For rigorous continuous differential mass transfer, two-film theory formulates bed height as the product of the Height of a Transfer Unit (HTU) and the Number of Transfer Units (NTU) : Z = HTU O G ⋅ NTU O G = HTU O L ⋅ NTU O L Z = \text{HTU}_{OG} \cdot \text{NTU}_{OG} = \text{HTU}_{OL} \cdot \text{NTU}_{OL} Z = HTU OG ⋅ NTU OG = HTU O L ⋅ NTU O L
Where: NTU O G = ∫ y 1 y 2 d y y ∗ − y , HTU O G = G m K O G a P \text{NTU}_{OG} = \int_{y_1}^{y_2} \frac{dy}{y^* - y}, \quad \text{HTU}_{OG} = \frac{G_m}{K_{OG} a P} NTU OG = ∫ y 1 y 2 y ∗ − y d y , HTU OG = K OG a P G m
G m G_m G m = molar vapor flux ( kmol/(s ⋅ m 2 ) \text{kmol/(s}\cdot\text{m}^2) kmol/(s ⋅ m 2 ) ).
K O G a K_{OG} a K OG a = overall volumetric gas mass transfer coefficient ( kmol/(s ⋅ m 3 ⋅ kPa) \text{kmol/(s}\cdot\text{m}^3\cdot\text{kPa)} kmol/(s ⋅ m 3 ⋅ kPa) ).
Analytical Relationship Between HETP and HTU
When the operating line and equilibrium line are straight, HETP is related to HTU O G \text{HTU}_{OG} HTU OG via the Stripping Factor ( λ \lambda λ ) : λ = m V L = m L / V \lambda = \frac{m V}{L} = \frac{m}{L/V} λ = L mV = L / V m
Where m = d y ∗ / d x m = dy^*/dx m = d y ∗ / d x is the equilibrium line slope. The mathematical transformation is: HETP = HTU O G ⋅ [ ln λ λ − 1 ] \text{HETP} = \text{HTU}_{OG} \cdot \left[ \frac{\ln \lambda}{\lambda - 1} \right] HETP = HTU OG ⋅ [ λ − 1 ln λ ]
When λ = 1.0 \lambda = 1.0 λ = 1.0 (parallel operating and equilibrium lines), lim λ → 1 ln λ λ − 1 = 1.0 ⟹ HETP = HTU O G \lim_{\lambda \to 1} \frac{\ln \lambda}{\lambda - 1} = 1.0 \implies \mathbf{\text{HETP} = \text{HTU}_{OG}} lim λ → 1 λ − 1 l n λ = 1.0 ⟹ HETP = HTU OG .
When λ > 1.0 \lambda > 1.0 λ > 1.0 , HETP < HTU O G \text{HETP} < \text{HTU}_{OG} HETP < HTU OG .
When λ < 1.0 \lambda < 1.0 λ < 1.0 , HETP > HTU O G \text{HETP} > \text{HTU}_{OG} HETP > HTU OG .
5. Comprehensive Comparison: Column Internals Performance Metrics
Internals Type Relative Cost Turndown Ratio Δ P \Delta P Δ P per Stage Capacity Fouling Resistance Best Industrial Applications
Sieve Trays Low ( 1.0 × 1.0\times 1.0 × ) Moderate ( 2 : 1 2:1 2 : 1 ) 4 – 8 mbar 4\text{--}8\text{ mbar} 4 – 8 mbar High Good (self-cleaning holes) Clean to moderate fouling chemical systems; steady rates
Valve Trays Moderate ( 1.2 × 1.2\times 1.2 × ) High ( 4 : 1 – 5 : 1 4:1\text{--}5:1 4 : 1 – 5 : 1 ) 5 – 9 mbar 5\text{--}9\text{ mbar} 5 – 9 mbar Very High Moderate (valves can stick) Crude atmospheric columns; wide feed turndown units
Bubble-Cap Trays High ( 2.5 × 2.5\times 2.5 × ) Very High ( > 8 : 1 >8:1 > 8 : 1 ) 8 – 15 mbar 8\text{--}15\text{ mbar} 8 – 15 mbar Moderate Poor (solids accumulate) Low liquid loads, batch distillation, chemical absorption
Random Packing Moderate ( 1.3 × 1.3\times 1.3 × ) Moderate ( 2.5 : 1 2.5:1 2.5 : 1 ) 1.5 – 3 mbar 1.5\text{--}3\text{ mbar} 1.5 – 3 mbar High Poor (bed traps particulates) Corrosive services, revamp of existing small trayed shells
Structured Packing High ( 2.0 – 3.0 × 2.0\text{--}3.0\times 2.0 – 3.0 × ) High ( 3 : 1 – 4 : 1 3:1\text{--}4:1 3 : 1 – 4 : 1 ) 0.5 – 1.5 mbar 0.5\text{--}1.5\text{ mbar} 0.5 – 1.5 mbar Maximum Very Poor (plugging risk) Deep vacuum distillation, ethylbenzene/styrene, heat-sensitive
- 6. Comprehensive Worked Numerical Example: Tray Column Diameter Sizing
- Problem Statement
A chemical plant fractionator rectifies an organic mixture with the following operating conditions at the top tray:
Vapor mass flow rate: W V = 18 , 000.0 kg/h W_V = 18,000.0\text{ kg/h} W V = 18 , 000.0 kg/h ( 5.000 kg/s 5.000\text{ kg/s} 5.000 kg/s )
Liquid mass flow rate: W L = 14 , 400.0 kg/h W_L = 14,400.0\text{ kg/h} W L = 14 , 400.0 kg/h ( 4.000 kg/s 4.000\text{ kg/s} 4.000 kg/s )
- Vapor mass density: ρ V = 2.500 kg/m 3 \rho_V = 2.500\text{ kg/m}^3 ρ V = 2.500 kg/m 3
- Liquid mass density: ρ L = 800.0 kg/m 3 \rho_L = 800.0\text{ kg/m}^3 ρ L = 800.0 kg/m 3
Liquid surface tension: σ = 24.0 dyn/cm \sigma = 24.0\text{ dyn/cm} σ = 24.0 dyn/cm ( 24.0 mN/m 24.0\text{ mN/m} 24.0 mN/m )
Tray spacing: T . S . = 24 inches T.S. = 24\text{ inches} T . S . = 24 inches ( 0.610 m 0.610\text{ m} 0.610 m )
Downcomer area: Designed to occupy 12.0 % 12.0\% 12.0% of the total column cross-sectional area ( A d c = 0.120 A c o l A_{dc} = 0.120 A_{col} A d c = 0.120 A co l , meaning net bubbling area A n e t = 0.880 A c o l A_{net} = 0.880 A_{col} A n e t = 0.880 A co l ).
From Fair's entrainment flooding chart at T . S . = 24 inches T.S. = 24\text{ inches} T . S . = 24 inches and the calculated flow parameter, the capacity parameter is C s b = 0.110 m/s C_{sb} = 0.110\text{ m/s} C s b = 0.110 m/s . The design engineer specifies that the superficial vapor velocity through the net active area must not exceed 80.0 % 80.0\% 80.0% of the flooding velocity ( u d e s = 0.800 u f u_{des} = 0.800 u_f u d es = 0.800 u f ).
Calculate:
The dimensionless Flow Parameter ( F l v F_{lv} F l v ).
The flooding vapor velocity ( u f u_f u f ) in m/s \text{m/s} m/s .
The design vapor velocity ( u d e s u_{des} u d es ) in m/s \text{m/s} m/s .
The volumetric vapor flow rate ( Q V Q_V Q V ) in m 3 /s \text{m}^3\text{/s} m 3 /s .
The required net bubbling area ( A n e t A_{net} A n e t ) and total column cross-sectional area ( A c o l A_{col} A co l ) in m 2 \text{m}^2 m 2 .
The inside diameter ( D c o l D_{col} D co l ) of the distillation column in meters and inches.
Step 1: Flow Parameter ( F l v F_{lv} F l v ) F l v = ( W L W V ) ρ V ρ L F_{lv} = \left( \frac{W_L}{W_V} \right) \sqrt{\frac{\rho_V}{\rho_L}} F l v = ( W V W L ) ρ L ρ V F l v = ( 14 , 400 18 , 000 ) 2.500 800.0 = 0.8000 × 0.003125 = 0.8000 × 0.05590 = 0.04472 F_{lv} = \left( \frac{14,400}{18,000} \right) \sqrt{\frac{2.500}{800.0}} = 0.8000 \times \sqrt{0.003125} = 0.8000 \times 0.05590 = \mathbf{0.04472} F l v = ( 18 , 000 14 , 400 ) 800.0 2.500 = 0.8000 × 0.003125 = 0.8000 × 0.05590 = 0.04472
Step 2: Flooding Vapor Velocity ( u f u_f u f ) ν f = C s b ( σ 20.0 ) 0.2 ρ L − ρ V ρ V \nu_f = C_{sb} \left( \frac{\sigma}{20.0} \right)^{0.2} \sqrt{\frac{\rho_L - \rho_V}{\rho_V}} ν f = C s b ( 20.0 σ ) 0.2 ρ V ρ L − ρ V
Evaluate each term:
Surface tension correction: ( 24.0 / 20.0 ) 0.2 = ( 1.200 ) 0.2 = 1.0371 (24.0 / 20.0)^{0.2} = (1.200)^{0.2} = 1.0371 ( 24.0/20.0 ) 0.2 = ( 1.200 ) 0.2 = 1.0371
Density buoyancy ratio: 800.0 − 2.500 2.500 = 797.50 2.500 = 319.0 = 17.8606 \sqrt{\frac{800.0 - 2.500}{2.500}} = \sqrt{\frac{797.50}{2.500}} = \sqrt{319.0} = 17.8606 2.500 800.0 − 2.500 = 2.500 797.50 = 319.0 = 17.8606 ν f = 0.110 m/s × 1.0371 × 17.8606 = 2.0376 m/s \nu_f = 0.110\text{ m/s} \times 1.0371 \times 17.8606 = \mathbf{2.0376\text{ m/s}} ν f = 0.110 m/s × 1.0371 × 17.8606 = 2.0376 m/s
Step 3: Design Vapor Velocity ( u d e s u_{des} u d es ) ν d e s = 0.800 × u f = 0.800 × 2.0376 m/s = 1.6301 m/s \nu_{des} = 0.800 \times u_f = 0.800 \times 2.0376\text{ m/s} = \mathbf{1.6301\text{ m/s}} ν d es = 0.800 × u f = 0.800 × 2.0376 m/s = 1.6301 m/s
Step 4: Volumetric Vapor Flow Rate ( Q V Q_V Q V ) Q V = W V ρ V = 5.000 kg/s 2.500 kg/m 3 = 2.000 m 3 /s Q_V = \frac{W_V}{\rho_V} = \frac{5.000\text{ kg/s}}{2.500\text{ kg/m}^3} = \mathbf{2.000\text{ m}^3\text{/s}} Q V = ρ V W V = 2.500 kg/m 3 5.000 kg/s = 2.000 m 3 /s
Step 5: Required Areas
Net bubbling area: A n e t = Q V u d e s = 2.000 m 3 /s 1.6301 m/s = 1.2269 m 2 A_{net} = \frac{Q_V}{u_{des}} = \frac{2.000\text{ m}^3\text{/s}}{1.6301\text{ m/s}} = \mathbf{1.2269\text{ m}^2} A n e t = u d es Q V = 1.6301 m/s 2.000 m 3 /s = 1.2269 m 2
Total column cross-sectional area: A c o l = A n e t 0.880 = 1.2269 m 2 0.880 = 1.3942 m 2 A_{col} = \frac{A_{net}}{0.880} = \frac{1.2269\text{ m}^2}{0.880} = \mathbf{1.3942\text{ m}^2} A co l = 0.880 A n e t = 0.880 1.2269 m 2 = 1.3942 m 2
Step 6: Column Diameter ( D c o l D_{col} D co l ) A c o l = π 4 D c o l 2 ⟹ D c o l = 4 A c o l π A_{col} = \frac{\pi}{4} D_{col}^2 \implies D_{col} = \sqrt{\frac{4 A_{col}}{\pi}} A co l = 4 π D co l 2 ⟹ D co l = π 4 A co l D c o l = 4 × 1.3942 m 2 3.14159 = 1.7751 = 1.332 m D_{col} = \sqrt{\frac{4 \times 1.3942\text{ m}^2}{3.14159}} = \sqrt{1.7751} = \mathbf{1.332\text{ m}} D co l = 3.14159 4 × 1.3942 m 2 = 1.7751 = 1.332 m
Converting to inches: D c o l = 1.332 m × ( 39.370 in 1 m ) = 52.45 in → 54 inches (standard fabrication shell) D_{col} = 1.332\text{ m} \times \left( \frac{39.370\text{ in}}{1\text{ m}} \right) = 52.45\text{ in} \to \mathbf{54\text{ inches (standard fabrication shell)}} D co l = 1.332 m × ( 1 m 39.370 in ) = 52.45 in → 54 inches (standard fabrication shell)
- 7. Critical PE Exam Traps & Pitfalls
- Trap 1: Calculating Superficial Velocity Using Total Tower Area Instead of Net Area
When applying Fair's flooding correlation, u f u_f u f is defined across the net bubbling area ( A n e t = A c o l − A d c A_{net} = A_{col} - A_{dc} A n e t = A co l − A d c ), which excludes the downcomer of the tray above. Sizing the tower diameter by dividing volumetric flow by total cross-sectional area directly causes the column to operate significantly closer to flood than designed, causing immediate entrainment.
Trap 2: Ignoring Froth Density in Downcomer Backup Calculations
Liquid inside a downcomer is not clear, deaerated liquid; it is aerated froth with a density roughly half that of pure liquid ( ρ f r o t h ≈ 0.50 ρ L \rho_{froth} \approx 0.50 \rho_L ρ f ro t h ≈ 0.50 ρ L ). If an engineer allows clear liquid height h d c h_{dc} h d c to reach 80 % 80\% 80% of tray spacing, the actual aerated froth height is h f r o t h = h d c / 0.50 = 1.6 × T . S . h_{froth} = h_{dc} / 0.50 = 1.6 \times T.S. h f ro t h = h d c /0.50 = 1.6 × T . S . , which submerges the tray above and causes massive downcomer flooding.
Trap 3: Specifying Trays for Deep Vacuum Service
In deep vacuum distillation ( P t o p < 50 mbar P_{top} < 50\text{ mbar} P t o p < 50 mbar or 35 mmHg 35\text{ mmHg} 35 mmHg ), specifying standard trays is a critical process error. A 30-tray column with a modest pressure drop of 5 mbar/tray 5\text{ mbar/tray} 5 mbar/tray generates a bottom pressure of 50 + ( 30 × 5 ) = 200 mbar 50 + (30 \times 5) = 200\text{ mbar} 50 + ( 30 × 5 ) = 200 mbar , a four-fold pressure increase! This raises the bottoms boiling temperature dramatically, causing severe product degradation and fouling. Structured packing ( Δ P ≈ 1 mbar/theoretical stage \Delta P \approx 1\text{ mbar/theoretical stage} Δ P ≈ 1 mbar/theoretical stage ) is virtually mandatory.